Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “location map”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

The local distribution of Na I interstellar gas

We present high-resolution absorption measurements (lambda/Delta lambda approximately 75,000) of the interstellar Na I D lines at 5890 A toward 80 southern hemisphere early-type stars located in the local interstellar medium (LISM). Combining these results with other sodium measurements taken from the literature, we produce galactic maps of the distribution of neutral sodium column density for a total of 293 stars generally lying within approximately 250 pc of the Sun. These maps reveal the approximate shape of the mid-plane contours of the rarefied region of interstellar space termed the Local Bubble. Its shape is seen as highly asymmetric, with a radius ranging from 30 to 300 pc, and with an average radius of 60 pc. Similar plots of the Galactic mid-plane distribution of sources emitting extreme ultraviolet radiation show that they also trace out similar contours of the Local Bubble derived from Na I absorption measurements. We conclude that the Local Bubble absorption interface can be represented by a hydrogen column density, Nu(sub ETA) = 2 x 10(exp 19) cm(exp -2), which explains both the local distribution of Na I absorption and the observed galactic distribution of extreme ultraviolet sources. The derived mid-plane contours of the Bubble generally reproduce the large-scale features carved out in the interstellar medium by several nearby galactic shell structures.

Welsh, B. Y.↗

South Pole Hydrogen Distribution for Present Lunar Conditions: Implications for Past Impacts

It has been known since the Lunar Prospector mission that the poles of the Moon evidently harbor enhanced concentrations of hydrogen [1,2]. The physical and chemical form of the hydrogen has been much debated. Using imagery from Clementine it was possible to roughly estimate permanently-shadowed regions (PSRs), and to perform image reconstructions of the Lunar Prospector epithermal neutron flux maps [3,4]. The hydrogen concentrations resulting from these reconstructions were consistent with a few weight percent water ice in selected locations. With the LCROSS impact, we now know that hydrogen in the form of ice does exist in lunar polar cold traps [5]. Armed with this information, and new data from LRO/Diviner, we can examine whether the pre-sent-day distribution of hydrogen in the form of water ice is consistent with a past large impact that delivered a large mass of volatiles to the lunar surface. These volatiles, mixed with solid impact ejecta, would then be lost from locations having high mean temperatures but would otherwise remain trapped in locations with sufficiently low mean annual temperatures [6]. The time scales for loss would depend on the location-dependent temperatures as well as impact history.

Elphic, R. C.↗

Large Meteoroid Impact on the Moon on 17 March 2013

Since early 2006, NASA's Marshall Space Flight Center has observed over 300 impact flashes on the Moon, produced by meteoroids striking the lunar surface. On 17 March 2013 at 03:50:54.312 UTC, the brightest flash of an 8-year routine observing campaign was observed in two 0.35 m telescopes outfitted with Watec 902H2 Ultimate monochrome CCD cameras recording interleaved 30 fps video. Standard CCD photometric techniques, described in [1], were applied to the video after saturation correction, yielding a peak R magnitude of 3.0 +/- 0.4 in a 1/30 second video exposure. This corresponds to a luminous energy of 7.1 × 10(exp 6) J. Geographic Information System (GIS) tools were used to georeference the lunar impact imagery and yielded a crater location at 20.60 +/- 0.17deg N, 23.92 +/- 0.30deg W. The camera onboard the Lunar Reconnaissance Orbiter (LRO), a NASA spacecraft mapping the Moon from lunar orbit, discovered the fresh crater associated with this impact by comparing post-impact images from 28 July 2013 to pre-impact images on 12 Feb 2012. The images show fresh, bright ejecta around an 18 m diameter circular crater, with a 15 m inner diameter measured from the level of pre-existing terrain, at 20.7135deg N, 24.3302deg W. An asymmetrical ray pattern with both high and low reflectance ejecta zones extends 1-2 km beyond the crater, and a series of mostly low reflectance splotches can be seen within 30 km of the crater - likely due to secondary impacts [2]. The meteoroid impactor responsible for this event may have been part of a stream of large particles encountered by the Earth/Moon associated with the Virginid Meteor Complex, as evidenced by a cluster of 5 fireballs seen in Earth's atmosphere on the same night by the NASA All Sky Fireball Network [3] and the Southern Ontario Meteor Network [4]. Assuming a velocity-dependent luminous efficiency (ratio of luminous energy to kinetic energy) from [5] and an impact velocity of 25.6 km/s derived from fireball measurements, the impactor kinetic energy was 5.4 × 10(exp 9) J and the impactor mass was 16 kg. Assuming an impact angle of 56deg from horizontal (based on fireball orbit measurements), a regolith density of 1500 kg/m(exp 3), and impactor density between 1800 and 3000 kg/m(exp 3), the impact crater diameter was estimated to be 8-18 m at the pre-impact surface and 10-23 m rim-to-rim using the Holsapple [6] and Gault [7] models, a result consistent with the observed crater.

Moser, Danielle E.↗

Flight Dynamics of Mars Helicopter

Starting with the first attempted flybys of Mars in the 1960s, human exploration of the Red Planet has evolved through ever-more sophisticated means, with the use of orbiters, stationary landers, and more recently rovers that have traveled over distances of tens of kilometers in search of new knowledge. Yet, despite discussion since the early days of space exploration, no mission has so far attempted to unlock the aerial dimension of Mars exploration through the use of atmospheric flyers. This could be about to change, as NASA is currently considering sending a small helicopter to the Martian surface as part of a future mission, as a technology demonstration to verify the feasibility and utility of using helicopters for future Mars exploration. The use of helicopters promises to bridge a resolution gap in current Mars exploration capabilities—betweeen orbiters providing large-area imagery at low resolution, and rovers that provide detailed imagery limited by line-of-sight from the current rover location. Paired with a rover, a helicopter can act as a forward reconnaisance platform, helping to identify promising science targets or mapping the terrain ahead of the rover. Looking further ahead, helicopters may one day carry their own science payloads to areas that are inaccessible to rovers.

San Martin, Miguel↗

Basin-wide gradients in dolomite d26Mg and 87Sr/86Sr identify the structural centre of the Williston Basin as a source of magnesium for dolomitization of the Middle Devonian Winnipegosis Formation

Dolomitized carbonates in the Williston Basin are common below the Middle Devonian Prairie Evaporite Formation, indicating a plausible role for brine-reflux as the source of Mg for dolomitization. However, the Lower Member Winnipegosis Formation, which directly underlies the evaporite sequence, exhibits dolomite 87Sr/86Sr ratios that are higher than expected for Middle Devonian seawater, instead suggesting that the dolomitizing fluids ascended from the deep basin where present-day formation waters are known to be more radiogenic. This interpretation is supported in this study by Mg isotope data showing a basin-scale gradient of increasing d26Mg values from the deep center (–2.03‰) to the edge (–1.34‰) of the Williston Basin along the lower Member Winnipegosis bed. Dolomite favors light isotopes of Mg when it forms, thus driving dolomitizing solutions, and the produced dolomite, towards heavier isotopic compositions in the direction of fluid flow. However, dolomite is also Mg-deficient when it forms, and its initial Mg isotope composition is susceptible to alteration by fluid-rock interactions occurring later in the depositional history of the deposit. We argue that the Mg isotope gradient in the Lower Member Winnipegosis was created by an ascending flow of isotopically light Mg-bearing fluid that differentially altered an earlier formed brine-reflux dolomite, with more alteration occurring deeper in the basin and less towards to edges. Alteration of pre-existing dolomite by an Mg isotope exchange mechanism requires large supplies of Mg. This fact, and the direction of fluid flow point to the underlying crystalline basement as an important Mg source for dolomitization in the Williston Basin. We speculate that ultramafic rocks supplied the Mg when they were hydrothermally altered during an anomalous heating event that affected the Williston Basin in the Late Devonian / Early Carboniferous. Seismic pumping drove these fluids upwards through fracture networks in the crust, and eventually into the deep center of the Williston Basin along vertically-oriented down-to-the-basement faults, pressuring deep aquifers like the Winnipegosis, which resulted in fluids migrating up the stratigraphic dip of the beds towards the edges of the basin. Plotting and contouring the dolomite d26Mg data on a map of the Williston Basin reveals the pathways taken by the migrating fluids. One prominent pathway extending outwards from the center of the basin towards the northeast bears a strong resemblance to petroleum migration fairways deduced for the underlying Late Ordovician Red River Formation. This study demonstrates that Mg isotopic mapping of large dolomite bodies is a useful tool for deciphering fluid flow histories in sedimentary basins and may assist in locating migrated petroleum and Mississippi Valley Type ore deposits.

Magnesium Isotopes, Strontium Isotopes, Dolomitiza↗

On the Thermal and Vibrational Properties of LaGaO3 Single Crystals

The thermal expansion and vibrational properties of [100] and [001] LaGaO3 single crystals have been studied by Thermal Mechanical Analysis and micro-Raman spectroscopy. A first order orthorhombic to rhombohedral phase transition has been confirmed by both techniques, as well as by in-situ heating using optical microscopy. The appearance of a metastable intermediate phase, tentatively assigned as monoclinic, has been detected both by optical microscopy and Raman spectroscopy upon heating of [100] and [001] LaGaO3 single crystals. Not only temperature but the stress induced orthorhombic to rhombohedral phase transition has also been detected by Raman mapping of the residual impression made by Vickers indentation. The position map of bands belonging to the lower temperature/pressure orthorhombic and the higher temperature/pressure rhombohedral phase show that the rhombohedral phase is located inside the impression, where the applied indentation stresses are the highest, and no rhombohedral phase can be located outside the impression, where the surface has not been altered by the contact stresses

36 MATERIALS SCIENCE↗

3D Lightning Geolocation With the CubeSpark Constellation

The new CubeSpark mission concept is being developed as a constellation of up to six satellites for high-resolution 3D lightning mapping. Each satellite in low-Earth orbit (LEO) will use optical and radio frequency (RF) sensors to geolocate individual sources from lightning flashes. The purpose of this study is to evaluate the potential accuracies and feasibilities of RF-based geolocation methods. This is done using a robust simulation framework to accurately depict the ionosphere’s effect on propagating RF signals, using their arrival times at each station to reconstruct source locations. We identified the primary sources of error as geometric, ionospheric, and instrumental. These are each analyzed to determine their quantitative effect on geolocation uncertainty. CubeSpark’s science objectives include mapping thundercloud charge regions and even individual flash channel structure for applications across a wide range of fields from climatology to hydrology. These applications require geolocation accuracy better than 1-2 km in each dimension, thus special care must be taken to optimize constellation design, minimize the main sources of error, and maximize CubeSpark’s potential. The algorithms developed in this study show promising results, with large regions having both horizontal and vertical uncertainties less than 1 km. After the removal of the Lightning Imaging Sensor from the International Space Station, an observational gap has been left for lightning observers from LEO. It therefore becomes increasingly vital to evaluate and improve on the current state of lightning mapping to prepare for the next generation of 3D lightning geolocation.

lightning↗

3D Lightning Geolocation with the CubeSpark Constellation

The new CubeSpark mission concept is being developed as a constellation of up to six satellites for high-resolution 3D lightning mapping. Each satellite in low-Earth orbit (LEO) will use optical and radio frequency (RF) sensors to geolocate individual sources from lightning flashes. The purpose of this study is to evaluate the potential accuracies and feasibilities of RF-based geolocation methods. This is done using a robust simulation framework to accurately depict the ionosphere’s effect on propagating RF signals, using their arrival times at each station to reconstruct source locations. We identified the primary sources of error as geometric, ionospheric, and instrumental. These are each analyzed to determine their quantitative effect on geolocation uncertainty. CubeSpark’s science objectives include mapping thundercloud charge regions and even individual flash channel structure for applications across a wide range of fields from climatology to hydrology. These applications require geolocation accuracy better than 1-2 km in each dimension, thus special care must be taken to optimize constellation design, minimize the main sources of error, and maximize CubeSpark’s potential. The algorithms developed in this study show promising results, with large regions having both horizontal and vertical uncertainties less than 1 km. After the removal of the Lightning Imaging Sensor from the International Space Station, an observational gap has been left for lightning observers from LEO. It therefore becomes increasingly vital to evaluate and improve on the current state of lightning mapping to prepare for the next generation of 3D lightning geolocation.

lightning↗

MECHANICAL PROPERTIES AND MICROSTRUCTURAL CHARACTERIZATION OF A MULTILAYERED MULTIPASS FRICTION STIR WELD IN STEEL

Multilayered multipass friction stir welding (MM-FSW) makes it possible to use FSW to fabricate thick-section structures. In this work, MM-FSW was demonstrated on a high strength low alloy steel; ASTM A572 Grade 50. Three steel plates with thicknesses of 0.18", 0.18", 0.24" respectively were stacked and friction stir welded together to form a 0.6" thick welded structure. The welded plate was sectioned into rectangular bars transverse to the weld direction for tensile testing to evaluate mechanical properties. Digital image correlation (DIC) was employed to map the local strain fields during tensile testing. The initial failure was found to occur simultaneously at the bottom and middle layers away from the weld zone. The top layer failed last in the base metal. The failure locations were consistent among different samples tested. Also, Charpy V-notch impact tests were conducted for weld metal, heat affected zone, and the base metal at each layer as a function of temperature. The weld microstructures were characterized using optical and electron microscopy and micro-hardness mapping.

Lim, Yong Chae↗

Experimental demonstration of passive acoustic imaging in the human skull cavity using CT-based aberration corrections

Purpose: Experimentally verify a previously described technique for performing passive acoustic imaging through an intact human skull using noninvasive, computed tomography (CT)-based aberration corrections Jones et al. [Phys. Med. Biol. 58, 4981–5005 (2013)]. Methods: A sparse hemispherical receiver array (30 cm diameter) consisting of 128 piezoceramic discs (2.5 mm diameter, 612 kHz center frequency) was used to passively listen through ex vivo human skullcaps (n = 4) to acoustic emissions from a narrow-band fixed source (1 mm diameter, 516 kHz center frequency) and from ultrasound-stimulated (5 cycle bursts, 1 Hz pulse repetition frequency, estimated in situ peak negative pressure 0.11–0.33 MPa, 306 kHz driving frequency) Definity™ microbubbles flowing through a thin-walled tube phantom. Initial in vivo feasibility testing of the method was performed. The performance of the method was assessed through comparisons to images generated without skull corrections, with invasive source-based corrections, and with water-path control images. Results: For source locations at least 25 mm from the inner skull surface, the modified reconstruction algorithm successfully restored a single focus within the skull cavity at a location within 1.25 mm from the true position of the narrow-band source. The results obtained from imaging single bubbles are in good agreement with numerical simulations of point source emitters and the authors’ previous experimental measurements using source-based skull corrections O’Reilly et al. [IEEE Trans. Biomed. Eng. 61, 1285–1294 (2014)]. In a rat model, microbubble activity was mapped through an intact human skull at pressure levels below and above the threshold for focused ultrasound-induced blood–brain barrier opening. During bursts that led to coherent bubble activity, the location of maximum intensity in images generated with CT-based skull corrections was found to deviate by less than 1 mm, on average, from the position obtained using source-based corrections. Conclusions: Taken together, these results demonstrate the feasibility of using the method to guide bubble-mediated ultrasound therapies in the brain. The technique may also have application in ultrasound-based cerebral angiography.

60 APPLIED LIFE SCIENCES↗

Flight Deck Surface Trajectory-Based Operations (STBO): A Four-Dimensional Trajectory (4DT) Simulation

In four-dimensional trajectory (4DT) Surface Trajectory-Based Operations (STBO), aircraft are assigned a conflict-free 4DT which defines an expected location (x,y coordinates) at all times, t, along the taxi route (with altitude, being fixed). These 4DTs afford the highest temporal certainty at all points along the taxi route, and at the departure runway. In the present study, a 4DT flight deck display was presented on the Airport Moving Map (AMM) to support pilot conformance to a 4DT clearance while taxiing under manual control. This pilot-in-the-loop simulation compared the effect of 4DT flight deck display formats on distance from the expected 4DT location, conformance to the displayed tolerance band, eyes-out time, and pilot ratings of safety and workload. In the defined-tolerance display format, a graphical representation of the expected 4DT location, with a distance-based allowable-tolerance band, was depicted on the AMM. Two defined-tolerance band sizes were tested: plus or minus 164 feet and plus or minus 405 feet. In the undefined-tolerance display format, the expected 4DT location was displayed graphically on the AMM, with no indicated allowable-tolerance bounds. Each taxi trial included 4DT speed changes (two or five, per trial) and a range of 4DT taxi speeds. Results showed that the larger (plus or minus 405 feet) defined-tolerance band yielded higher conformance levels than the smaller (plus or minus 164 feet) band, with pilots staying within the specified and displayed conformance bounds more in the larger (99.71%) than the smaller defined-tolerance band (93.37 percent). However, in terms of being able to predict the location of the aircraft compared to the expected 4DT location, the smaller defined-tolerance band resulted in pilots keeping their aircraft closer to the 4DT location, for both average distance and for a given confidence interval (e.g., 95 percent), than either the larger defined-tolerance band or the undefined-tolerance display format. The larger tolerance band yielded more “eyes-out-the-window” time than the smaller tolerance band. Pilots also rated taxing with the larger tolerance band as safer than the smaller tolerance band.

STBO↗

Point Cloud Based Mapping of Understory Shrub Fuel Distribution, Estimation of Fuel Consumption and Relationship to Pyrolysis Gas Emissions on Experimental Prescribed Burns

Forest fires spread via production and combustion of pyrolysis gases in the understory. The goal of the present paper is to understand the spatial location, distribution, and fraction (relative to the overstory) of understory plants, in this case, sparkleberry shrub, namely its degree of understory consumption upon burn, and to search for correlations between the degree of shrub consumption to the composition of emitted pyrolysis gases. Data were collected in situ at seven small experimental prescribed burns at Ft. Jackson, an army base in South Carolina, USA. Using airborne laser scanning (ALS) to map overstory tree crowns and terrestrial laser scanning (TLS) to characterize understory shrub fuel density, both pre- and postburn estimates of sparkleberry coverage were obtained. Sparkleberry clump polygons were manually digitized from a UAV-derived orthoimage of the understory and intersected with the TLS point cloud-derived rasters of pre- and postburn shrub fuel bulk density; these were compared in relation to overstory crown cover as well as to ground truth. Shrub fuel consumption was estimated from the digitized images; sparkleberry clump distributions were generally found to not correlate well to the overstory tree crowns, suggesting it is shade-tolerant. Moreover, no relationship was found between the magnitude of the fuel consumption and the chemical composition of pyrolysis gases, even though mixing ratios of 25 individual gases were measured.

54 ENVIRONMENTAL SCIENCES↗

Identification of a QTL region for tomato brown rugose fruit virus resistance in Solanum pimpinellifolium

Abstract Tomato (Solanum lycopersicumL.), one of the most widely grown vegetables in the world, has been seriously impacted in the past decade by the emerging tomato brown rugose fruit virus (ToBRFV). ToBRFV is a seed-borne tobamovirus, with ability to overcome the commonly usedTm-2 2 resistance gene in tomato. The objective of this study was to conduct quantitative trait locus (QTL) mapping and identify single-nucleotide polymorphism (SNP) markers associated with ToBRFV resistance in tomato. Two F 2 populations were used for QTL mapping: One derived from a cross betweenS. pimpinellifoliumUSVL333 (PI 390718) × USVL332 (PI 390717) and another from ‘Moneymaker’ × USVL332 (PI 390717), with population sizes of 195 and 79 plants, respectively. The resistance trait was derived from theS. pimpinellifoliumaccession USVL332 (PI 390717). A major QTL for ToBRFV resistance was identified on chromosome 11 (SL4.0ch11), with the peak located at approximately 46.84 Mbp. This QTL spans a 22-kb interval between 46,825,788 bp and 46,847,421 bp, as determined through both genome-wide association study (GWAS) and QTL linkage mapping. Three SNP markers, SL4.0ch11_46825788, SL4.0ch11_46847421, and SL4.0ch11_46850215, demonstrated the most significant association with high LOD values (LOD = 13 in the Blink model) in GWAS analysis. In this genomic region, two disease resistance gene analogs, Solyc11g062150 (TIR-NBS-LRR resistance protein, Toll-Interleukin receptor) and Solyc11g062180 (disease resistance protein, leucine-rich repeat), were identified, which may serve as candidates for ToBRFV resistance. The QTL identified in this study could be valuable for plant breeders in facilitating tomato breeding with ToBRFV resistance.

Agriculture↗

ERTS-1 MSS imagery: Its use in delineating soil associations and as a base map for publishing soils information

ERTS 1 imagery is a useful tool in the identification and refinement of soil association areas and an excellent base map upon which soil association information can be published. Prints of bands 5 and 7 were found to be most useful to help delineate major soil and vegetation areas. After delineating major soil areas, over 4800 land sale prices covering a period of 1967-72 were located in the soil areas and averaged. The soil association then were described as soil association value areas and published on a 1:1,000,000 scale ERTS mosaic of South Dakota constructed using negative prints of band 7. The map is intended for use by state and county revenue officers, by individual buyers and sellers of land and lending institutions, and as a reference map by those planning road routes and cable lines and pipelines.

Westin, F. C.↗

Appendices for Geothermal Exploration Artificial Intelligence Report

The Geothermal Exploration Artificial Intelligence looks to use machine learning to spot geothermal identifiers from land maps. This is done to remotely detect geothermal sites for the purpose of energy uses. Such uses include enhanced geothermal system (EGS) applications, especially regarding finding locations for viable EGS sites. This submission includes the appendices and reports formerly attached to the Geothermal Exploration Artificial Intelligence Quarterly and Final Reports. The appendices below include methodologies, results, and some data regarding what was used to train the Geothermal Exploration AI. The methodology reports explain how specific anomaly detection modes were selected for use with the Geo Exploration AI. This also includes how the detection mode is useful for finding geothermal sites. Some methodology reports also include small amounts of code. Results from these reports explain the accuracy of methods used for the selected sites (Brady Desert Peak and Salton Sea). Data from these detection modes can be found in some of the reports, such as the Mineral Markers Maps, but most of the raw data is included the DOE Database which includes Brady, Desert Peak, and Salton Sea Geothermal Sites.

15 GEOTHERMAL ENERGY↗

Geothermal Play Fairway Analysis for Low-Temperature Resources in the Denver Basin

This dataset is part of an effort to highlight the advantages of incorporating low-temperature (< 150 C) geothermal resource evaluation into the implementation of combined heat and power (CHP), and geothermal direct use (GDU) technologies (e.g., space heating and/or cooling). For this Denver Basin example, resource favorability maps were created to identify potentially favorable areas for further geothermal exploration and are provided here. Favorability was based on three types of data: (1) geologic, (2) economic, and (3) risk. This raw data is also provided below. Geologic data include bottom-hole temperatures (BHT) from oil and gas wells, water co-production volumes from oil and gas wells, well groundwater levels, hot spring locations, temperatures, and chemistries, faults, and earthquakes. Economic feasibility data include population, thermal energy demand, infrastructure, and roads. Risk data (which includes data on excluded areas) include flood plains, protected lands (e.g. wildlife conservation areas, national parks). The included report describes this project in detail, covering workflows, relevant datasets, Python code, and both common and composite maps used to create low-temperature geothermal resource favorability maps for the Denver Basin, which extends across Colorado, Nebraska, and Wyoming. The figures in this report include: maps of the original datasets; maps of transformed data and derived parameters (such as the geothermal gradient or thermal conductivity); results of uncertainty analyses; results of data completeness (using the GeoRePORT tool); examples of the data combination and processing (using the geoPFA Python library, which is introduced in the attached report); favorability maps for each criteria; and a final combined favorability map. This project is designed to facilitate future deployment of CHP and GDU by providing data, tools, and a workflow applicable to low-temperature geothermal resources in sedimentary basins.

15 GEOTHERMAL ENERGY↗

User Guide for the Anvil Threat Cooridor Forecast Tool V2.4 for AWIPS

The Anvil Tool GUI allows users to select a Data Type, toggle the map refresh on/off, place labels, and choose the Profiler Type (source of the KSC 50 MHz profiler data), the Date- Time of the data, the Center of Plot, and the Station (location of the RAOB or 50 MHz profiler). If the Data Type is Models, the user selects a Fcst Hour (forecast hour) instead of Station. There are menus for User Profiles, Circle Label Options, and Frame Label Options. Labels can be placed near the center circle of the plot and/or at a specified distance and direction from the center of the circle (Center of Plot). The default selection for the map refresh is "ON". When the user creates a new Anvil Tool map with Refresh Map "ON, the plot is automatically displayed in the AWIPS frame. If another Anvil Tool map is already displayed and the user does not change the existing map number shown at the bottom of the GUI, the new Anvil Tool map will overwrite the old one. If the user turns the Refresh Map "OFF", the new Anvil Tool map is created but not automatically displayed. The user can still display the Anvil Tool map through the Maps dropdown menu* as shown in Figure 4.

Barett, Joe H., III↗

Chile Disasters: Automating Wildfire Risk and Occurrence Mapping in Google Earth Engine to Improve Wildfire Detection and Response Time Efforts

Wildfires in Chile in the last decade were the worst on record, destroying homes and livelihoods, polluting the air, and displacing whole towns. To predict locations where wildfires were likely to start, the Corporación Nacional Forestal (CONAF) created a wildfire risk model within ArcGIS Pro and Google Earth Engine (GEE) that utilized the NOAA Global Forecast System (GFS) and the NASA Shuttle Radar Topography Mission (STRM) 90-meter datasets. The previous CONAF model was very resource-heavy and time-intensive to run. NASA DEVELOP, in partnership with CONAF, automated the previous model and transferred it fully into GEE where all Earth observation datasets could be used without downloading. The new model substantially reduced the runtime. The final model was used to create a near real-time wildfire monitoring application as well as fire severity maps. The end products will be used by CONAF for wildfire prediction and management to prevent more destruction in the future.

Maria De Los Santos↗

Refine your search to explore more results.