Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “frequency shift”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Continuous wave dye-laser technique for simultaneous, spatially resolved measurements of temperature, pressure, and velocity of NO in an underexpanded free jet

Gas dynamic quantities within an underexpanded nitrogen free jet, seeded with 0.5 percent NO, were measured nonintrusively by using an intracavity-doubled, rapid-tuning, CW ring dye laser. The UV beam passed obliquely through the jet axis, and its frequency repetitively scanned across adjacent rotational lines in the NO gamma band near 225 nm at a rate of 4 kHz. Spatially resolved excitation scans were obtained by monitoring the induced broadband fluoresence. Modeling the Doppler-shifted excitation scans with Voigt profiles permitted simultaneous determinations of NO velocity, rotational temperature, and pressure. Zero Doppler shift was referenced to an absorption trace obtained across a static cell and recorded concurrently with the excitation scan. Typically, the measured and predicted axial distributions agreed within 10 percent. At high Mach numbers there was evidence of rotational freezing of NO.

Di Rosa, Michael D.↗
NASA NTRS2000

BOREAS RSS-17 Dielectric Constant Profile Measurements

The BOREAS RSS-17 team acquired and analyzed imaging radar data from the ESA's ERS-1 over a complete annual cycle at the BOREAS sites in Canada in 1994 to detect shifts in radar backscatter related to varying environmental conditions. This data set consists of dielectric constant profile measurements from selected trees at various BOREAS flux tower sites. The relative dielectric constant was measured at C-band (frequency = 5 GHz) as a function of depth into the trunk of three trees at each site, Measurements were made during April 1994 with an Applied Microwave Corporation field PDP fitted with a 0.358-cm (0.141-inch) diameter coaxial probe tip. The data are available in tabular ASCII files. The data files are available on a CD-ROM (see document number 20010000884), or from the Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC).

Hall, Forrest G.↗
NASA NTRS2004

Robust Timing Synchronization in Aeronautical Mobile Communication Systems

This work details a study of robust synchronization schemes suitable for satellite to mobile aeronautical applications. A new scheme, the Modified Sliding Window Synchronizer (MSWS), is devised and compared with existing schemes, including the traditional Early-Late Gate Synchronizer (ELGS), the Gardner Zero-Crossing Detector (GZCD), and the Sliding Window Synchronizer (SWS). Performance of the synchronization schemes is evaluated by a set of metrics that indicate performance in digital communications systems. The metrics are convergence time, mean square phase error (or root mean-square phase error), lowest SNR for locking, initial frequency offset performance, midstream frequency offset performance, and system complexity. The performance of the synchronizers is evaluated by means of Matlab simulation models. A simulation platform is devised to model the satellite to mobile aeronautical channel, consisting of a Quadrature Phase Shift Keying modulator, an additive white Gaussian noise channel, and a demodulator front end. Simulation results show that the MSWS provides the most robust performance at the cost of system complexity. The GZCD provides a good tradeoff between robustness and system complexity for communication systems that require high symbol rates or low overall system costs. The ELGS has a high system complexity despite its average performance. Overall, the SWS, originally designed for multi-carrier systems, performs very poorly in single-carrier communications systems. Table 5.1 in Section 5 provides a ranking of each of the synchronization schemes in terms of the metrics set forth in Section 4.1. Details of comparison are given in Section 5. Based on the results presented in Table 5, it is safe to say that the most robust synchronization scheme examined in this work is the high-sample-rate Modified Sliding Window Synchronizer. A close second is its low-sample-rate cousin. The tradeoff between complexity and lowest mean-square phase error determines the rankings of the Gardner Zero-Crossing Detector and both versions of the Early-Late Gate Synchronizer. The least robust models are the high and low-sample-rate Sliding Window Synchronizers. Consequently, the recommended replacement synchronizer for NASA's Advanced Air Transportation Technologies mobile aeronautical communications system is the high-sample-rate Modified Sliding Window Synchronizer. By incorporating this synchronizer into their system, NASA can be assured that their system will be operational in extremely adverse conditions. The quick convergence time of the MSWS should allow the use of high-level protocols. However, if NASA feels that reduced system complexity is the most important aspect of their replacement synchronizer, the Gardner Zero-Crossing Detector would be the best choice.

Xiong, Fu-Qin↗
DOE OSTI2020

An Adaptive Reference Scheme to Extend the Functional Range of Optical Backscatter Reflectometry in Extreme Environments

Optical frequency domain reflectometry (OFDR) measurements are performed by recording the interference pattern of light backscattered by density fluctuations or Bragg gratings along the length of an optical fiber. Changes in local temperature or strain in the fiber cause shifts in the backscattered light spectrum, which can be calibrated to the applied temperature or strain. Comparing the backscattered optical spectra from each reflection site with a reference (unstrained) spectrum allows for quantification of local spectral shifts. While mature OFDR-based technologies can provide high-precision spatially distributed measurements over kilometer lengths, the post-processing approaches used to recover spectral shifts from raw optical intensity data can limit the use of OFDR in harsh environments. This paper presents a novel approach to post-processing OFDR data which extends the usability of optical fibers exposed to harsh environments. This approach is the first to use the spectral shift quality, calculated for two OFDR measurements, to identify an appropriate reference scan from which the spectral shift can be determined. Here, three experimental data sets are used to test the algorithm: (1) an optical fiber heated to >950°C, (2) an aluminum-embedded optical fiber under strain from differential thermal expansion, and (3) an optical fiber exposed to a total neutron flux of 2×10 13 n/cm 2 /s over 40 hours in a nuclear test reactor. Results show that using a metric of quality to select an appropriate reference measurement extends the functional range of OFDR strain and temperature sensors. Furthermore, this algorithm can be applied to existing OFDR data.

47 OTHER INSTRUMENTATION↗
NASA NTRS1974

Wideband infrared heterodyne receiver front-end

A 10.6 micron infrared heterodyne receiver front end was developed for use in a wideband CO2 laser communications link. The infrared receiver employs an 850 MHz response PV HgCdTe photomixer which is mounted in a space quality housing, a low-noise 5 to 1500 MHz IF preamplifier, and a remote control panel. The receiver was designed to handle + or - 750 MHz of Doppler shift while providing an instantaneous information bandwidth of 400 MHz. The measured receiver sensitivity NEP was 1.0 x 10 to the 19th power W/Hz for a photomixer temperature of T sub m = 77 K and an IF beat frequency of 20 MHz and degraded to 1.75 x 10 to the 19th power W/Hz for T sub m = 130 K.

Peyton, B. J.↗
NASA NTRS1978

Time domain phase measuring apparatus

The phase and/or period stability of a device is determined by connecting the device in one orthogonal arm of a phase detector having a mixer. In the other arm is an adjustable, variable phase shift device. The output of the mixer is fed through an active low pass filter to derive a DC voltage indicative of the phase shift. The variable phase device is adjusted so that the DC voltage will nullify the phase shift of the tested device under normal conditions. The DC voltage level is converted into a time interval indicative of the phase change of the tested device by determining when the level equals the amplitude of a low frequency ramp voltage. The interval between adjacent equality points can be measured or the period between a reference point on the ramp voltage and the quality be measured.

Reinhardt, V. S.↗
NASA NTRS1983

Variability in the power spectrum of solar five-minute oscillations

It is noted that two-dimensional power spectra of solar five-minute oscillations exhibit prominent ridge structures in (k, omega) space, k being the horizontal wavenumber and omega the temporal frequency. The positions of these ridges in k and omega can be used in probing temperature and velocity structures in the subphotosphere. The progress made in a program to establish whether power spectra taken on separate days show shifts in ridge locations is surveyed, noting that these may arise from different velocity and temperature patterns having been brought into the sampling region by solar rotation. Power spectra are obtained for six days of observations of Doppler velocities using the Mg I 5173 A and Fe I 5434 A spectral lines. Each data set encompasses 8 to 11 hr in time and samples a region 256 x 1024 arcsec in spatial extent, with a spatial resolution of 2 arcsec and temporal sampling of 65 s. Statistically significant shifts are detected in ridge locations between certain data sets. When analyzed in terms of eastward and westward propagating waves, the character of these displacements is seen as implying that changes have occurred in both temperature and horizontal velocity fields underlying the observing window. The velocity changes are estimated to be of the order of 100 m/s.

Hill, F.↗
NASA NTRS1990

Acquisition of the QPSK demodulator in the presence of interference

The acquisition behavior of the tracking and data relay satellite system (TDRSS) receiver (a quadrative phase-shift keying (QPSK) demodulator using a dither lock detector) in the presence of interference from another user has been analyzed using a simulation model. The demodulator is composed of an automatic gain control, a QPSK Costas loop, a frequency sweep unit, lock test units, and a control unit. The simulation model has been tested for the following variables: signal and interference Doppler frequencies and phase offsets (with respect to initial voltage control oscillator setup), signal-to-interference ratio (SIR), and signal I/Q power ratio. The simulation results are discussed.

Ghazvinian, Farzad↗
NASA NTRS1993

Investigation of plasma instabilities in the Polar cusp

During the last six months, our efforts concentrated on studying the excitation of electromagnetic waves in the whistler frequency range by an anisotropic electron beam. A paper entitled 'Electron Cyclotron Wave Generation by Relativistic Electrons' was submitted to Journal of Geophysical Research and was accepted for publication. This paper is in collaboration with Dr. M. L. Goldstein at Goddard Space Flight Center. It was shown that an anisotropic electron beam (or gyrating electron beam) is capable of generating electron cyclotron waves with frequency from above to below the electron plasma frequency in a low density plasma. This instability may account for the observed Z mode and the electromagnetic component of auroral hiss in the Earth's polar region. The abstract of this paper is enclosed. For a high density plasma in which the electron plasma frequency is considerably higher than the electron cyclotron frequency, a new left-hand electromagnetic wave at whistler frequencies, which is also driven unstable by an anisotropic electron beam, was found. The basic notion of this new instability is the significant change of the dispersion equation due to the contribution of the beam component, which can shift the usual right hand whistler waves into left hand waves.

Wong, H. K.↗
NASA NTRS2008

Neutron Stars and Black Holes Seen with the Rossi X-Ray Timing Explorer (RXTE)

Astrophysical X-rays bring information about location, energy, time, and polarization. X-rays from compact objects were seen in the first explorations to vary in time. Eclipses and pulsations have simple explanations that identified the importance of X-ray binaries and magnetic neutron stars in the first decade of X-ray astronomy. The dynamics of accretion onto stellar and supermassive black holes and onto neutron stars with relatively low magnetic fields shows up as more complex variations, quasi-periodic oscillations, noise with characteristic frequency spectra, broad-band changes in the energy spectra. To study these variations, RXTE instruments needed to have large area and operational flexibility to find transient activity and observe when it was present. Proportional counters and Phoswich scintillators provided it in a modest mission that has made textbook level contributions to understanding of compact objects. The first seen, and the brightest known, X-ray binary, Sco X-1 is one of a class of neutron stars with low mass companions. Before RXTE, none of these had been seen to show pulsations, though they were hypothesized to be the precursors of radio pulsars with millisecond periods and low magnetic fields. RXTE's large area led to identifying coherent millisecond pulsars in a subset which are relatively faint transients. It also led to identifying short episodes of pulsation during thermonuclear bursts, in sources where a steady signal is not seen. The X-ray stage verifies the evolution that produces millisecond radio pulsars.Masses and radii of neutron stars are being determined by various techniques, constraining the equation of state of matter at nuclear densities. Accretion should lead to a range of neutron star masses. An early stage of superstrong magnetic field neutron stars is now known to produce X-ray and gamma-ray bursts in crust quakes and magnetic field reconnection releases of energy. Soft Gamma Repeaters, Anomolous X-ray Pulsars, and high magnetic field rotation-powered pulsars are all now called magnetars, because they have pulse periods indicating they are slowing down as they would with magnetic dipole radiation for a surface field above 5x1013 gauss. The accretion disk has been connected to the launching of radio jets from black holes, and even from neutron stars. Estimates of the angular momenta of black holes are being made from different approaches, modelling a high frequency oscillation that may be related to how close the inner part of the accretion disk is to the black hole, modelling the continua spectra of the X-ray emission, and modeling the emission of red-shifted iron that may be emitted from the accretion disk. These investigations require early discovery of the black hole transient with the All Sky Monitor on RXTE or other monitoring information, frequent extended observations, and coordinated observations with missions that give higher energy resolution, or radio and infrared information.

Swank, Jean↗
NASA NTRS2018

System to Perform Radio Frequency Interferometry Using Optical Fiber Sensing Signal Processing Techniques

Aspects of the present disclosure involve a system and method for performing radio frequency interferometry using optical fiber sensing. Optical fiber sensing is performed as a reference signal is defined and compared, in the optical domain, to incoming signals to obtain interference fringe patterns that can be used to decode phase shift offsets with respect to the designated reference signal. The phase shift offsets can be determined by first optically modulating the reference and incoming signals using a laser source as the carrier. In the optical domain, the reference and incoming signals are combined using an optical coupler and then converted back to the electrical domain for processing.

Ott, Melanie N.↗
NASA NTRSDate not supplied

TPSAS-NF1676L-31460-DND

Summary - An upward shift of cirrus clouds at a rate higher than that predicted by the climate models is observed in the last 16 years. - Only sub-visible cirrus clouds exhibited upward shift in their altitude. - Optical thickness of sub-visible and thick cirrus clouds showed decreasing trends. - No significant trend was obtained from the CALIOP data over Gadanki. - SAGE-II data show increasing trend in the occurrence frequency of aerosol and decreasing trend in aerosol-cloud mixture - CALIOP observations show increase in cirrus cloud occurrence in Western-equatorial pacific.

Amit Kumar Pandit↗
DOE OSTI2023

A New Plasma Radar Concept for Simultaneous Magnetic and Density Measurements

An innovative, compact 288GHz interferometer has been fabricated, tested, installed and successfully demonstrated on the LAPD-U magnetized plasma at UCLA. The system takes advantage of frequency modulated (FM) radar techniques to deliver a compact heterodyne system. In addition, the reflected power from the source is taken advantage of to eliminate the need for additional quasi-optical components. Electron density in LAPD-U plasma has recently been increased substantially thereby requiring a higher frequency/shorter wavelength interferometer to avoid deleterious refractive effects. This system satisfies those needs. The system uses a 96GHz varactor tuned Gunn oscillator which passes to a passive tripler. This tripler has ~3% conversion efficiency. The 288GHz radiation is then coupled to free space using a so-called dual-mode or Pickett horn. The output 288GHz beam is then coupled to an aspheric lens manufactured from low-loss, high-density polyethylene. This lens is employed to collimate the emerging beam. Small axial adjustment of the lens position can also be used to create a slowly focusing beam so as to optimize the measured signal. In addition, up-down or side-to-side adjustment of the lens can be utilized to steer the beam vertically or horizontally – again to optimize alignment. The propagating beam passes through a beam splitter and then through a water-free, bubble-free fused quartz window into the LAPD-U vacuum vessel. The beam-splitter is a thin sheet of G10 which reflects a small fraction of the incident power (~5 %) towards a zero-bias detector optimized for the frequency range from 220 to 300GHz. Note that waveguides at this frequency have dimensions of ~0.9mm x 0.45mm and so have very large conductive losses. This drives the use of quasi-optical propagation. The detector requires no DC bias and is very responsive (> 1V/mW into 1MΩ). Radiation is coupled to the detector via a similar lens-horn arrangement used for the launch. This reflected beam acts as the local oscillator or reference millimeter-wave beam for the detector. The remainder of the launched source beam then enters the LAPD-U vacuum vessel and passes through the plasma at the mid-plane until reaching the opposing port which is closed off with an aluminum flange. This flange is used as a mirror to retroreflect the incident 288GHz beam back along its path. The retroreflected beam exits the input port but does NOT couple directly into the zero-bias detector. Instead, the majority of the return power continues towards the 288GHz source. As mentioned above the transmitted beam enters the source a second time. This would appear undesirable. However, at these frequencies multipliers are highly non-linear elements which results in a significant portion of the return beam (~20%) re-emerging from the multiplier and horn and then coupling via the G10 beam-splitter to the zero-bias detector. This approach eliminated the need for a second quasi-optical beam-splitter. The system is extremely compact measuring approximately 28 inches x 20 inches. The above did not explain how heterodyne operation was achieved. As mentioned above the Gunn oscillator is able to be varactor tuned. This allows a low voltage to be applied to control the operating frequency of the Gunn oscillator. During heterodyne operation a sawtooth shaped voltage is applied to the varactor at 750kHz using an 80MHz Arbitrary Waveform Generator (AWG). This voltage changes the Gunn frequency linearly during the up-sweep which is then reset abruptly at the sawtooth crash to be immediately followed by another linear sweep. Passage through the 288GHz multiplier triples the frequency change experienced by the electromagnetic wave. These frequency changes are small – tens of megahertz. This FM radar approach results in the launched electromagnetic wave frequencies at the detector for the reference and plasma wave to be different. The approximately 10 ns delay propagation delay for the plasma beam results in the local oscillator and plasma beams NOT having an identical frequency – there is in fact a fixed difference frequency. The frequency tuning level of the Gunn oscillator is then adjusted so that there is ONE cycle of this difference frequency during each linear ramp. During the sawtooth crash or downward re-sweep this one cycle replays in reverse but on a very fast timescale. The process then repeats. Low-pass filtering eliminates the fast re-sweep to leave a pure sine wave heterodyne signal. When the plasma is present it introduces a phase delay in the sine wave (caused by the extremely small Doppler shift resulting from the optical path length change). Of course, to measure this phase change we need a reference. This is simply obtained from an arbitrary waveform generator which provides a synchronized output pulse train which again is low pass filtered to obtain a 750kHz sinusoidal voltage reference for the interferometer. The interferometer was installed on LAPD-U where it has worked reliably and has established that electron densities exceeding 1x10 13 cm -3 are routinely achieved. In addition, the system sensitivity was able to easily observe density fluctuation at frequencies up to 50kHz. FM Radar techniques have enabled a full demonstration of a compact, sensitive, high frequency (288GHz/1mm) heterodyne interferometer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

The Diurnal Dynamics of Gross Primary Productivity Using Observations From the Advanced Baseline Imager on the Geostationary Operational Environmental Satellite‐R Series at an Oak Savanna Ecosystem

Gross primary productivity (GPP) is the largest flux in the global carbon cycle and satellite-based GPP estimates have long been used to study the trends and interannual variability of GPP. With recent updates to geostationary satellites, we can now explore the diurnal variability of GPP at a comparable spatial resolution to polar-orbiting satellites and at temporal frequencies comparable to eddy covariance (EC) tower sites. We used observations from the Advanced Baseline Imager on the Geostationary Operational Environmental Satellite-R series (GOES-R) to test the ability of subdaily satellite data to capture the shifts in the diurnal course of GPP at an oak savanna EC site in California, USA that is subject to seasonal soil moisture declines. We compared three methods to estimate GPP: (a) a light-use efficiency model, (b) a linear relationship between the product of near-infrared reflectance of vegetation and photosynthetically active radiation (LIN-NIR v P) and EC tower GPP, and (c) a light response curve (LRC-NIR v P) between NIR v P and EC GPP. The LRC-NIR v P achieved the lowest mean absolute error for winter (2 µmol CO 2 m –2 s –1 ), spring (2.51 µmol CO 2 m –2 s –1 ), summer (1.43 µmol CO 2 m –2 s –1 ), and fall (1.35 µmol CO 2 m –2 s –1 ). The ecosystem experienced the largest shift in daily peak GPP in relation to the peak of incoming solar radiation toward the morning hours during the dry summers. The LRC-NIRvP and the light-use efficiency model were in agreement with these patterns of a shift in peak daily GPP toward the morning hours during summer. Our results can help develop diurnal estimates of GPP from geostationary satellites that are sensitive to fluctuating environmental conditions during the day.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Floquet-engineered fast SNAP gates in weakly coupled circuit-QED systems

Superconducting cavities with high quality factors, coupled to a fixed-frequency transmon, provide a state-of-the-art platform for quantum information storage and manipulation. The commonly used selective number-dependent arbitrary phase ( SNAP ) gate faces significant challenges in ultrahigh-coherence cavities, where the weak dispersive shifts necessary for preserving high coherence typically result in prolonged gate times. Here, in this work, we propose a protocol to achieve high-fidelity SNAP gates that are orders of magnitude faster than the standard implementation, surpassing the speed limit set by the bare dispersive shift. We achieve this enhancement by dynamically amplifying the dispersive coupling via sideband interactions, followed by quantum optimal control on the Floquet-engineered system. We also present a unified perturbation theory that explains both the gate acceleration and the associated benign drive-induced decoherence, corroborated by Floquet-Markov simulations. These results pave the way for the experimental realization of high-fidelity, selective control of weakly coupled, high-coherence cavities, and expanding the scope of optimal control techniques to a broader class of Floquet quantum systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Temporal reflection from short pump pulses inside a dispersive nonlinear medium: the impact of pump parameters

We have studied, through a series of experiments and numerical simulations, how temporal reflection from an intense pump pulse inside a photonic crystal fiber is affected by parameters of the pump pulse used to form a moving high-index boundary. We used femtosecond pump pulses, which slow down inside the fiber as their spectrum red-shifts because of intrapulse Raman scattering. Temporal reflection of probe pulses occurs from such decelerating pump pulses. We changed the width and chirp of our pump pulses with a 4f pulse shaper capable of providing both spectral filtering and frequency chirping. We found that temporal refection exhibited novel features, to our knowledge, when pump pulses were made wider or chirped. In both cases, two or more reflected pulses were produced at different wavelengths in a specific range of the initial pump-probe delays. Furthermore, numerical simulations reveal that the origin of such novel features is related to the complex nonlinear evolution of pump pulses inside optical fibers.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Advancing the central role of non-model biorepositories in predictive modeling of emerging pathogens

The COVID-19 pandemic demonstrated the insufficiency of a reactive approach to emerging zoonotic pathogens. With spillover increasing in frequency as environments change and the human footprint continues to grow, pandemic prevention will require predictive models that can identify (i) potential zoonoses with a high likelihood of emergence and (ii) environmental or other features that may trigger a shift in host, vector, or pathogen baselines associated with emergence and/or spillover. Artificial intelligence (AI), and particularly its machine learning and deep learning branches, holds enormous potential for detecting shifts in large-scale biodiversity and disease datasets (genomic, ecological, geospatial, etc.). Such algorithms can be trained to identify subtle patterns in large volumes of data to yield insights into complex phenomena for which we have limited knowledge of the true cause(s) or predictor(s), as is the case for emerging infectious diseases.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1979

Choice of method for discretization of continuous systems

The paper discusses and compares several common methods of discretizing the transfer function of a continuous control system so that a digital computer can be used. The discretization effect on the frequency response attenuation of the simple transfer function G(s) = 1/(s + 1) is illustrated for the Tusting, Boxer-Thaler, Madwed, linear segment approximation, and stair-step with half period advanced methods. The input frequency must be significantly lower than one-half the sampling error to have negligible discretization error. Phase differences due to discretization are also plotted, and it is seen that the zero-order hold contributes much more phase shift than that due to discretization. In situations where zero-order hold must follow a computer, the method of discretization of a continuous system is not a major factor if phase shift is important.

Mcvey, E. S.↗

Refine your search to explore more results.