Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “control layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

Altitude/path-angle transitions in fuel-optimal problems for transport aircraft

Altitude/path angle transitions to fuel-optimal, energy climb and descent paths are examined for subsonic transport aircraft. These transitions are termed boundary layers in singular perturbation theory, the framework used herein to simplify solutions to the state-Euler system. The energy climb and descent paths provide equilibrium or stationary points for the boundary layer system, and thus for moderate transitions, presumed valid for the class of aircraft considered, the boundary layer system may be linearized. This simplification allows derivation of an explicit solution to the two-point boundary-value, boundary layer problem and, as a consequence, yields a nearly optimal control law, in feedback form, for the transitions. Numerical simulation results using the feedback control law are presented for a Boeing 737 airframe (NASA-ATOPS Vehicle) employing twin JT8D-7-7A engines.

Gracey, C.↗

Fresh attack on laminar flow

Laminar flow control is a technology with great potential for aircraft drag reduction. Stabilization of laminar boundary layers became known as natural laminar flow (NLF) and research led to the development of NLF airfoils. Research was also conducted on stabilization by suction, referred to as laminar flow control (LFC). Experiments demonstrated that extensive laminar flow could be achieved in flight. However, there remained doubts regarding the practicality of producing, with the technology then available, wing surfaces sufficiently smooth and wavefree to meet laminar-flow criteria and maintaining the wing surface quality in normal service. In 1976, the Aircraft Energy Efficiency (ACEE) program was begun by NASA to develop fuel-conservative technology for commercial transports. The progress of the ACEE program is discussed. Attention is given to LFC wing structures, and LFC leading-edge systems.

Wagner, R. D.↗

Spacecraft contamination: Sources and prevention; Thermophysics Conference, 18th, Montreal, Canada, June 1-3, 1983, Selected Papers

Results of current research in the field of spacecraft contamination are presented. An overview of the various sources of contamination is given, showing the many and diverse mechanisms associated with the degradation of thermal and optical performance of spacecraft surfaces and optics. Some of the causes of contamination are discussed, including spallation of foam insulation on cryogenic fuel tanks, dispersion of particle contamination about a spacecraft, particle contamination of optical sensors, and the influence of the location of venting systems. Contamination prevention is addressed. Infrared transmittance and infrared optical properties of contaminants are considered along with the effects and properties of mixtures of exhaust species, of plume boundary layer flow, and of the contamination associated with bipropellant attitude control thrusters proposed for the Galileo spacecraft. Also discussed are: degradation of 'clean' thermal control surfaces over four years in orbit, in-orbit measurement of solar absorptance, and contamination from postfire efflux of a solid-propellant rocket motor.

Roux, J. A.↗

Flat-plate transition

A new research effort was undertaken to build a boundary-layer transition tunnel. This facility only recently became operational. The data obtained so far are merely qualitative. The main goal is to predict heat transfer given any combination of factors such as pressure gradient, turbulence level, Reynolds number, or intermittency factor. The boundary-layer transition tunnel is a closed-loop tunnel that controls the turbulence level, velocity and temperature of the air within it. Problems associated with the operation of this tunnel are examined.

Ercegovic, B. A.↗

Numerical experiments on subcritical transition mechanisms

A spectral algorithm for simulating three-dimensional, incompressible, parallel shear flows is described. It applies to the channel, to the parallel boundary layer, and to other shear flows with one wall-bounded and two periodic directions. Simulations performed for the channel identify the one nonlinear interaction which is crucial to the secondary instability. Moreover, it is shown that subharmonic instability ensues for Reynolds numbers as low as 1500. Simulations performed for the heated water boundary layer reveal the operation of the secondary instability in this controlled flow.

Zang, T. A.↗

Stability theory applications to laminar-flow control

In order to design Laminar Flow Control (LFC) configurations, reliable methods are needed for boundary-layer transition predictions. Among the available methods, there are correlations based upon R sub e, shape factors, Goertler number and crossflow Reynolds number. The most advanced transition prediction method is based upon linear stability theory in the form of the e sup N method which has proven to be successful in predicting transition in two- and three-dimensional boundary layers. When transition occurs in a low disturbance environment, the e sup N method provides a viable design tool for transition prediction and LFC in both 2-D and 3-D subsonic/supersonic flows. This is true for transition dominated by either TS, crossflow, or Goertler instability. If Goertler/TS or crossflow/TS interaction is present, the e sup N will fail to predict transition. However, there is no evidence of such interaction at low amplitudes of Goertler and crossflow vortices.

Malik, Mujeeb R.↗

BLSTA: A boundary layer code for stability analysis

A computer program is developed to solve the compressible, laminar boundary-layer equations for two-dimensional flow, axisymmetric flow, and quasi-three-dimensional flows including the flow along the plane of symmetry, flow along the leading-edge attachment line, and swept-wing flows with a conical flow approximation. The finite-difference numerical procedure used to solve the governing equations is second-order accurate. The flow over a wide range of speed, from subsonic to hypersonic speed with perfect gas assumption, can be calculated. Various wall boundary conditions, such as wall suction or blowing and hot or cold walls, can be applied. The results indicate that this boundary-layer code gives velocity and temperature profiles which are accurate, smooth, and continuous through the first and second normal derivatives. The code presented herein can be coupled with a stability analysis code and used to predict the onset of the boundary-layer transition which enables the assessment of the laminar flow control techniques. A user's manual is also included.

Wie, Yong-Sun↗

Replicate Wolter-I x-ray mirrors

Cylindrical (hyperbolic - parabolic Wolter I) mirrors have been electroformed from nickel over an electroless nickel-phosphorous (NiP) plated aluminum mandrel in support of the NASA AXAF-S x-ray spectrometer program. The electroless nickel was diamond turned and polished to achieve a surface finish of 10 angstroms rms or better. Gold was then plated on the nickel alloy after an electrochemical passivation step. Next a heavy layer of pure nickel was plated one millimeter thick with controlled stress at zero using a commercial PID program to form the actual mirror. This shell was removed from the NiP alloy coated mandrel by cryogenic cooling and contraction of the aluminum to release the mirror. It is required that the gold not adhere well to the NiP but all other plated coatings must exhibit good adherence. Four mirrors were fabricated from two mandrels prepared by this method. The area of each part is 0.7 square meters (7.5 square feet).

Engelhaupt, D. E.↗

Evaluation of Tropospheric Water Vapor Simulations from the Atmospheric Model Intercomparison Project

Simulations of humidity from 28 general circulation models for the period 1979-88 from the Atmospheric Model Intercomparison Project are compared with observations from radiosondes over North America and the globe and with satellite microwave observations over the Pacific basin. The simulations of decadal mean values of precipitable water (W) integrated over each of these regions tend to be less moist than the real atmosphere in all three cases; the median model values are approximately 5% less than the observed values. The spread among the simulations is larger over regions of high terrain, which suggests that differences in methods of resolving topographic features are important. The mean elevation of the North American continent is substantially higher in the models than is observed, which may contribute to the overall dry bias of the models over that area. The authors do not find a clear association between the mean topography of a model and its mean W simulation, however, which suggests that the bias over land is not purely a matter of orography. The seasonal cycle of W is reasonably well simulated by the models, although over North America they have a tendency to become moister more quickly in the spring than is observed. The interannual component of the variability of W is not well captured by the models over North America. Globally, the simulated W values show a signal correlated with the Southern Oscillation index but the observations do not. This discrepancy may be related to deficiencies in the radiosonde network, which does not sample the tropical ocean regions well. Overall, the interannual variability of W, as well as its climatology and mean seasonal cycle, are better described by the median of the 28 simulations than by individual members of the ensemble. Tests to learn whether simulated precipitable water, evaporation, and precipitation values may be related to aspects of model formulation yield few clear signals, although the authors find, for example, a tendency for the few models that predict boundary layer depth to have large values of evaporation and precipitation. Controlled experiments, in which aspects of model architecture are systematically varied within individual models, may be necessary to elucidate whether and how model characteristics influence simulations.

Gaffen, Dian J.↗

Hybrid Thermal Control Testing of a Cryogenic Propellant Tank

This report presents the experimental results of a hybrid thermal control system, one that integrates a passive system (multi-layer insulation) with an active system (a mechanical cyrocooler) applied to cryogenic propellant storage. These experiments were performed on a 1.39 m diameter spherical propellant tank filled with LH2 while installed in an evacuated chamber. The tank heat transfer to the cryocooler was accomplished with a condenser installed in the ullage of the tank and mated to the second stage of the cooler, and by conduction, through copper leaves mated to the first stage of the cooler. The first hybrid system test was performed with both the condenser and the leaves, a configuration that had excess capacity to remove the heat entering the tank; the second test was performed with only the condenser, with a capacity closely matched to the tank heating rate. In both of these tests, the goal of zero boil-off was achieved.

Plachta, David W.↗

Chemistry and Transport In a Multi-Dimensional Model

The focus of the work funded under this proposal is the exchange between the stratosphere and the troposphere, and between the troposphere and the blaspheme. These two interfaces represent the frontiers of atmospheric chemistry. It is the combination of exchange processes at both interfaces that ultimately controls how the blaspheme (including human activities) affects the ozone layer. The modeling work was motivated by and attempts to integrate information obtained by aircraft, spacecraft, shuttle and oceanic measurements. The model development and research activities accomplished in the past three years provide a technical and intellectual basis for the research in this group. The innovative part of our research program is related to the IAV of ozone and the hydrological cycle. Other related but independently supported work include the study of isotopic fractionation of atmospheric species, e.g., N2O and CO2. Our theory suggests that we now have the ability to probe the middle atmosphere at a level of sensitivity where subtle details such as the isotopic composition of simple molecules can yield measurable systematic effects. This creates the possibility for probing the chemistry and dynamics of the middle atmosphere using all of the N2O and CO2 isotopologues. In the following we will briefly describe the model development and review the highlights of recent accomplishments.

Yung, Yuk L.↗

Laser Synthesis of Supported Catalysts for Carbon Nanotubes

Four methods of laser assisted catalyst generation for carbon nanotube (CNT) synthesis have been tested. These include pulsed laser transfer (PLT), photolytic deposition (PLD), photothermal deposition (PTD) and laser ablation deposition (LABD). Results from each method are compared based on CNT yield, morphology and structure. Under the conditions tested, the PLT was the easiest method to implement, required the least time and also yielded the best pattemation. The photolytic and photothermal methods required organometallics, extended processing time and partial vacuums. The latter two requirements also held for the ablation deposition approach. In addition to control of the substrate position, controlled deposition duration was necessary to achieve an active catalyst layer. Although all methods were tested on both metal and quartz substrates, only the quartz substrates proved to be inactive towards the deposited catalyst particles.

VanderWal, Randall L.↗

Astronaut Thermal Exposure: Re-Entry After Low Earth Orbit Rescue Mission

The STS-125 mission, launched May 11, 2009, is the final servicing mission to the Hubble Space Telescope. The repair mission's EVA tasks are described, including: installing a new wide field camera; installing the Cosmic Origins Spectrograph; repairing the Space Telescope Imaging Spectrograph; installing a new outer blanket layer; adding a Soft Capture and Rendezvous System for eventual controlled deorbit in about 2014; replacing the 'A' side Science Instrument Command and Data Handling module; repairing the Advanced Camera for surveys; and, replacing the rate sensor unit gyroscopes, fine guidance sensors and 3 batteries. Additionally, the Shuttle crew cabin thermal environment is described. A CFD model of per person CO2 demonstrates a discrepancy between crew breathing volume and general mid-deck levels of CO2. A follow-on CFD analysis of the mid-deck temperature distribution is provided. Procedural and engineering mitigation plans are presented to counteract thermal exposure upon reentry to the Earth atmosphere. Some of the procedures include: full cold soak the night prior to deorbit; modifying deck stowage to reduce interference with air flow; and early securing of avionics post-landing to reduce cabin thermal load prior to hatch opening. Engineering mitigation activities include modifying the location of the aft starboard ICUs, eliminating the X3 stack and eliminating ICU exhaust air directed onto astronauts; improved engineering data of ICU performance; and, verifying the adequacy of mid-deck temperature control using CFD models in addition to lumped parameter models. Post-mitigation CFD models of mid-deck temperature profiles and distribution are provided.

Gillis, David B.↗

Magnetization of the Lunar Crust

Magnetic fields measured by the satellite Lunar Prospector show large scale features resulting from remanently magnetized crust. Vector data synthesized at satellite altitude from a spherical harmonic model of the lunar crustal field, and the radial component of the magnetometer data, have been used to produce spatially continuous global magnetization models for the lunar crust. The magnetization is expressed in terms of localized basis functions, with a magnetization solution selected having the smallest root-mean square magnetization for a given fit to the data, controlled by a damping parameter. Suites of magnetization models for layers with thicknesses between 10 and 50 km are able to reproduce much of the input data, with global misfits of less than 0.5 nT (within the uncertainties of the data), and some surface field estimates. The magnetization distributions show robust magnitudes for a range of model thicknesses and damping parameters, however the magnetization direction is unconstrained. These global models suggest that magnetized sources of the lunar crust can be represented by a 30 km thick magnetized layer. Average magnetization values in magnetized regions are 30-40 mA/m, similar to the measured magnetizations of the Apollo samples and significantly weaker than crustal magnetizations for Mars and the Earth. These are the first global magnetization models for the Moon, providing lower bounds on the magnitude of lunar crustal magnetization in the absence of multiple sample returns, and can be used to predict the crustal contribution to the lunar magnetic field at a particular location.

Lunar↗

Thermal Protection Systems Technology Transfer from Apollo and Space Shuttle to the Orion Program

This paper describes how the Orion program is utilizing the Thermal Protection System (TPS) experience from the Apollo and Space Shuttle programs to reduce program risk and improve affordability to meet NASA's future manned exploration missions. The Orion program successfully completed the Exploration Flight Test (EFT-1) mission in 2014 and is currently assembling, integrating, and testing the next spacecraft for the Exploration Mission (EM-1) to meet the flight test objectives of an unmanned orbital mission to the moon and return to earth in 2019. The Orion spacecraft production operations are located in the Neil Armstrong Operations and Checkout (O&C) facility at the Kennedy Space Center (KSC) providing an affordable and seamless delivery approach of vehicles directly to the launch site eliminating spacecraft transportation and additional checkout testing. Innovative vehicle design, manufacturing and test operations approaches are maturing and evolving with each Orion vehicle build to support the challenging NASA exploration mission requirements beyond Low Earth Orbit (LEO) while reducing program cost and schedule impacts. An example of Orion's evolution is the incorporation of an improved heat shield design, assembly and testing approach to meet the higher re-entry velocities for a lunar return for the EM-1 mission. The EFT- 1 heat shield was based on the Apollo heat shield manufacturing processes and was assembled at a supplier location and then transported to KSC for final integration. The EM-1 heat shield is now manufactured, assembled, tested, and installed into the spacecraft at the O&C facility reducing program cost and production schedules. The transition of the Space Shuttle TPS capabilities has enabled Orion to provide a human rated capsule design using proven materials and processes established over years of orbiter re-entry missions. The Orion Crew Module (CM) TPS configuration is derived from the Apollo CM approach utilizing improved materials and processes developed from the Space Shuttle program. The Orion EFT-1 heat shield utilized the Avcoat ablative material from Apollo which was injected into a honeycomb substrate and has been updated for EM-1 incorporating a block configuration bonded to a composite shell structure. This approach utilizes the proven Avcoat material for the heat shield ablator and is utilizing derived bonding and inspection methods and techniques from the Space Shuttle tile experience. The Orion back shell TPS configuration is based on Space Shuttle tile designs using proven tile materials and coatings. The Orion forward bay cover utilizes the high temperature tiles similar to the back shell tiles and low temperature blankets derived from the Space Shuttle program reducing weight impacts. Space Shuttle Multi-Layer Insulation (MLI) is installed in the Orion capsule to control the interior temperature environment providing a light weight design. These TPS design approaches have performed successfully on the Orion first flight test on EFT-1 and are incorporated in the configuration for the next flight test for EM-1. Completion of these two flight tests will certify the TPS for the Orion program for human rated exploration missions and has reduced the development cost to the Orion program. In addition to transitioning the Space Shuttle TPS design configurations to Orion, the supporting manufacturing infrastructure, manufacturing processes, and inspection methods are also incorporated into the Orion assembly operations at KSC. This has avoided significant startup schedule and costs impacts of new capabilities and development of support operations necessary to fabricate, install, inspect, and validate the TPS installations for the Orion spacecraft. The Thermal Protection System Facility (TPSF) which supported the Space Shuttle program provides the heat shield Avcoat blocks and the back shell AETB-8 tiles for Orion program. Extending the existing Space Shuttle TPS operations at KSC provides onsite support to the Orion spacecraft assembly operations. A significant benefit to the Orion program is the transition of the Space Shuttle technician work force at KSC. This highly skilled workforce was able to transition to the Orion program and immediately support the TPS installation operations. They brought with them the human rated manufacturing and assembly operations culture that was critical to the Space Shuttle success avoiding the retraining cost and schedule impacts of a new workforce to Orion. The technician skills certification program from the Space Shuttle was found to be compatible with the Lockheed Martin technician certification programs enabling a seamless training process utilizing process similarity avoiding the cost of retraining the work force to Orion standards. The existing workforce is certificated for multiple processes enabling reassignment of technicians to other tasks in the Orion AI&P operations reducing the overall touch labor manpower requirements. Additional benefits of using the Space Shuttle workforce is the incorporation of the lessons learned from Space Shuttle processes to improve the Orion TPS processes. This has resulted in a continuous evolution of TPS processes to improve the producibility and reduce the program cost for the TPS for the Orion program. Transitioning the Apollo and Space Shuttle TPS designs, processes, and technician workforce has been instrumental in enabling Orion to successfully meet the program challenges for NASA's exploration missions of the future.

Stewart, Michael↗

Capsule_Grid User Guide

Software utility CAPSULE_GRID and several related procedures that automate grid generation for computational fluid dynamics calculations about axisymmetric atmospheric entry vehicles are described as a supplement to the documentation within the source codes. This application program and its ancillary software utilities are all in the public domain at the web site https://software.nasa.gov/software/category/all/arc/1/cfdtools with the exception of the 2D hyperbolic volume gridding step for which scripts driving either GRIDGEN1 or HYPGEN2 are available. CAPSULE_GRID was developed at NASA Ames Research Center in support of the DPLR3 real gas flow solver. Both forebodies (only) and full bodies are treated, for axisymmetric 2D flow calculations or for 3D calculations at angle of attack. The expected application is to the smooth outer mold line of a hypersonic atmospheric entry vehicle, for which a single layer of point-matched structured grid blocks normally suffices. Control files for a variety of representative cases are included with illustrations of results, and some insights into the subtleties of curvature-based grid point distribution are provided. Gridding of a capsule on a sting is supported. Additional procedures for treating arbitrarily long 2D wakes, prompted by asteroid studies and relevant to spacecraft such as Stardust, are also documented. Most recently, treating an asymmetric forebody (including an off-center nose, with or without an aft body) has been incorporated as an extra step.

spacecraft↗

Experimental Evaluation of Hot Films on Ceramic Substrates for Skin-Friction Measurement

An investigation has been performed on the use of low-thermal conductivity, ceramic substrates for hot films intended to measure skin friction. Hot films were deposited on two types of ceramic substrates. Four hot films used composite-ceramic substrates with subsurface thermocouples (TCs), and two hot films were deposited on thin Macor(R) substrates. All six sensors were tested side by side in the wall of the NASA Glenn Research Center 8-ft by 6-ft Supersonic Wind Tunnel (SWT). Data were obtained from zero flow to Mach 1.98 in air. Control measurements were made with three Preston tubes and two boundary-layer rakes. The tests were repeated at two different hot film power levels. All hot films and subsurface TCs functioned throughout the three days of testing. At zero flow, the films on the high-thermal conductivity Macor(R) substrates required approximately twice the power as those on the composite-ceramic substrates. Skin-friction results were consistent with the control measurements. Estimates of the conduction heat losses were made using the embedded TCs but were hampered by variability in coating thicknesses and TC locations.

Noffz, Gregory K.↗

Experimental Study of Fillets to Reduce Corner Effects in an Oblique Shock-Wave/Boundary Layer Interaction

A test was conducted in the 15 cm x 15 cm supersonic wind tunnel at NASA Glenn Research Center that focused on corner effects of an oblique shock-wave/boundary-layer interaction. In an attempt to control the interaction in the corner region, eight corner fillet configurations were tested. Three parameters were considered for the fillet configurations: the radius, the fillet length, and the taper length from the square corner to the fillet radius. Fillets effectively reduced the boundary-layer thickness in the corner; however, there was an associated penalty in the form of increased boundary-layer thickness at the tunnel centerline. Larger fillet radii caused greater reductions in boundary-layer thickness along the corner bisector. To a lesser, but measureable, extent, shorter fillet lengths resulted in thinner corner boundary layers. Overall, of the configurations tested, the largest radius resulted in the best combination of control in the corner, evidenced by a reduction in boundary-layer thickness, coupled with minimal impacts at the tunnel centerline.

Fillets↗

Refine your search to explore more results.