Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TiP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Blade and Rim Seal Design of a First Stage High Pressure Turbine for a 300 MWe Supercritical CO2 Power Cycle

A first stage high-pressure turbine (HPT) blade is optimized for a 300 MWe supercritical CO2 (sCO2) power cycle using the surrogate-assisted genetic algorithm optimizer in Numeca FINE/Design 3D with objectives of increasing efficiency and decreasing heat load to the blade. The National Institute of Standards and Technology Reference Fluid Thermodynamic and Transport Properties Database (NIST REFPROP) [1] data for supercritical CO2 is formatted into tables of bicubic polynomial coefficients for use in condensable gas simulations in FINE/Turbo. Nearly 3000 unique shapes are evaluated via three-dimensional Reynolds Averaged Navier Stokes simulations, yielding increases in efficiency of up to 0.85 percentage points and decreases in heat load of 14%. A final blade, deemed the advanced blade, is chosen for future experimental analysis. Following this, a squealer tip optimization is performed on both the baseline and advanced blade designs. This optimization resulted in a performance gain of 1.25 points in efficiency and 15% reduction in tip heat load compared to the baseline flat tip design at the same clearance. In tandem, an optimization of the rotor-stator platform rim seal is performed using a parametrized geometry allowing for straight, meandering, and knife seal cavities. This multi-objective optimization focuses on decreasing the cooling mass flow and increasing the heat flux from the rotor and stator disk. The optimization resulted in cooling mass flow decreases of up to 26% while maintaining the average heat flux on the rim seal.

Tuite, Logan↗
DOE OSTI2025

Cryogenic Optical and Spin Scanning Probe Station for High-throughput Characterization of Solid-state Quantum Defects

This final technical report provides an overview of the key milestones achieved by Advanced Research Systems (ARS), a DOE SBIR/STTR Grant Recipient. ARS’s main objective was to develop a prototype of the Closed Cycle Cryogenic Quantum Probe Station (Avalanche). Designed for near field spectroscopy (Tip Enhanced Photoluminescence, TEPL and Tip Enhanced Raman Spectroscopy TERS) and far field spectroscopy (micro-Raman, micro-PL) is in the final stage of completion. The critical components have been tested and the final System Test of the AFM is scheduled for August 2025.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Finite domain solution of a hydraulic fracture in a permeable rock

In this work, we present a domain-based algorithm to simulate the propagation of a plane-strain hydraulic fracture in a zero-toughness permeable elastic medium. The algorithm utilizes a domain-based method to solve the elasticity equation and integrates a multi-scale tip asymptote, which is particular to hydraulic fractures, into this framework. This integration is key to accurately model the energy dissipation and the fluid leak-off in the fracture tip region. The algorithm combines a 2D finite volume method (FVM) for solving the elasticity equation with a 1D FVM for solving the nonlinear lubrication equation. Incorporating the far-field asymptotics and using a moving-mesh scheme reduces the computational burden while improving the accuracy of the scheme. The paper concludes with an analysis of the numerical results. This study demonstrates the potential of this domain-based approach for modeling hydraulic fractures in poroelastic media.

Domain-based method↗
DOE OSTI2022

Embedded sensors integrated into critical components for in situ health monitoring of steam turbines

Operational flexibility is desired in today’s coal-fired power plants to balance power grids by compensating for the variable electricity supply from renewable energy sources and distributed gensets. This demanding requirement accelerates materials degradation and makes in-situ health monitoring essential. Life monitoring of components and subsystems is thus seen as essential in assessing material and mechanical behavior to estimate system reliability, move to a conditionbased maintenance strategy and determine time to failure of the units in their actual operating conditions. Vibration monitoring can be exploited for blade tip timing to measure blade vibration amplitude and tip clearance to detect any deterioration taking place in the condition of steam turbine blades. A failure of a rotating blade can lead to severe turbine damage followed by extensive repairs and loss of power production. A blade vibration monitoring system can help early detection of abnormal blade vibration behavior. In conjunction with a health monitoring system, the vibration characteristics can be analyzed to support a pro-active maintenance and inspection schedule. While the feasibility of this inspection technique has been amply demonstrated, there is a need to install induction probes to magnetize the blade for signal output. Siemens, in partnership with Raytheon Technologies Research Corporation (RTRC), proposes a holistic approach to develop embedded sensors to utilize radio frequency for not only coupling to sensors, but as the sensing modality. The goal of this project is to “embed” the novel sensing approach by using either additively manufactured or extruded waveguides on rotating blades for recording, evaluation and monitoring of blade vibrations in Low Pressure turbines, with applications extending to aero engines

01 COAL, LIGNITE, AND PEAT↗
NASA NTRS1922

Air Reactions to Objects Moving at Rates Above the Velocity of Sound with Application to the Air Propeller

There has been a tradition general among aeronautical engineers that a critical point exists for tip speeds at or near the velocity of sound, indicating a physical limit in the use of propellers at higher tip speeds; the idea being that something would occur analogous to what is known in marine propellers as cavitation. In the examination of the physics pertaining to both propellers and projectiles moving at or above 1100 feet per second, the conclusion was reached by the author that there is no reason for the existence of such a critical point and that, if it had been noted by observers it was not inherent in the phenomena revealed, but rather due to a particular shape or proportion of the projectile and that, with properly proportioned sections, it would not exist.

PROPELLERS - CURTISS-REED↗
DOE OSTI2023

Enhancing Organic Semiconductor Molecular Packing Using Perovskite Interfaces to Improve Singlet Fission

Singlet fission, a process by which one singlet exciton is converted into two lower energy triplet excitons, is sensitive to the degree of electronic coupling within a molecular packing structure. Variations in molecular packing can be detrimental to triplet formation and triplet–triplet separation, ultimately affecting the harvesting of triplets for electricity in organic photovoltaic devices. Here, six phase-pure molecular packing structures of 6,13-bis(triisopropylsilylethynyl)pentacene (TIPS-pentacene) with varying optoelectronic properties are isolated using 2D lead halide perovskites as tunable, crystalline surfaces for crystallization. Transient absorption spectroscopy reveals that while triplet formation is fast (<100 fs) regardless of template structure, the increased ordering in perovskite-templated samples speeds up triplet–triplet separation and recombination, providing evidence that the benefits of phase-purity offset minor variations in molecular packing. Molecular dynamics modeling of the interface reveals that perovskite-templating allows for closer packing of TIPS-pentacene molecules for all perovskite templates. With an extensive number of organic molecule-perovskite pairings, this work provides a methodology to use ordered, periodic surfaces to elucidate structure–property relationships of small organic molecules in order to adjust structural or optoelectronic responses, such as molecular packing and singlet fission.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Rational Regulation of Layer‐by‐Layer Processed Active Layer via Trimer‐Induced Pre‐Swelling Strategy for Efficient and Robust Thick‐Film Organic Solar Cells

Thick-film (>300 nm) organic solar cells (OSCs) have garnered intensifying attention due to their compatibility with commercial roll-to-roll printing technology for the large-scale continuous fabrication process. However, due to the uncontrollable donor/acceptor (D/A) arrangement in thick-film condition, the restricted exciton splitting and severe carrier traps significantly impede the photovoltaic performance and operability. For this work, combined with layer-by-layer deposition technology, a twisted 3D star-shaped trimer (BTT-Out) is synthesized to develop a trimer-induced pre-swelling (TIP) strategy, where the BTT-Out is incorporated into the buried D18 donor layer to enable the fabrication of thick-film OSCs. The integrated approach characterizations reveal that the exceptional configuration and spontaneous self-organization behavior of BTT-Out trimer could pre-swell the D18 network to facilitate the acceptor's infiltration and accelerate the formation of D/A interfaces. This enhancement triggers the elevated polarons formation with amplified hole-transfer kinetics, which is essential for the augmented exciton splitting efficiency. Furthermore, the regulated swelling process can initiate the favorable self-assembly of L8-BO acceptors, which would ameliorate carrier transport channels and mitigate carrier traps. As a result, the TIP-modified thin-film OSC devices achieve the champion performance of 20.3% (thin-film) and 18.8% (thick-film) with upgraded stability, among one of the highest performances reported of thick-film OSCs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

3D Printing of Highly Porous Polypropylene Separators for Lithium‐Ion Batteries Using Fused Deposition Modeling and Thermally Induced Phase Separation

Appearing as one of the key-components of lithium-ion batteries (LIBs), this work specifically focuses on the additive manufacturing (AM) of custom-shape separators, facilitated by the filament material extrusion process, also called fused deposition modeling (FDM). The development and optimization of composite thermoplastic filament feedstocks combining polypropylene and paraffin wax, followed by the 3D printing of the separator membranes is shown. A post-processing step, based on thermal induced phase separation (TIPS), is introduced to promote porosity formation through removal of the paraffin wax sacrificial phase within the 3D printed items. Separators with different polypropylene/paraffin wax ratios are developed and the impact on printability, mechanical strength, porosity, and electrochemical performances, is thoroughly discussed. X-ray micro-computed tomography is employed to assess the geometric fidelity and to detect printing defects in a complex 3D lattice structure. The performance of the 3D printed porous separators is also compared to a commercial separator. This pioneering research establishes a foundation for the creation of porous separators that can adapt to and conform into 3D printed battery architectures with novel form factors, and also creates opportunities for the use of FDM and TIPS for a wide range of applications that employ porous structures beyond the energy storage field.

3D printing↗
DOE OSTI2026

Proximity Ferroelectricity in Compositionally Graded Structures

Proximity ferroelectricity is a novel paradigm for inducing ferroelectricity in a non-ferroelectric polar material, such as AlN or ZnO that are typically unswitchable with an external field below their dielectric breakdown field. When placed in direct contact with a thin switchable ferroelectric layer (such as Al 1-x Sc x N or Zn 1-x Mg x O), they become a practically switchable ferroelectric. Using the thermodynamic Landau-Ginzburg-Devonshire theory, in this work, we perform the finite element modeling of the polarization switching in the compositionally graded AlN-Al 1-x Sc x N, ZnO-Zn 1-x Mg x O, and MgO-Zn 1-x Mg x O structures sandwiched in both a parallel-plate capacitor geometry as well as in a sharp probe-planar electrode geometry. We reveal that the compositionally graded structure allows the simultaneous switching of spontaneous polarization in the whole system by a coercive field significantly lower than the electric breakdown field of unswitchable polar materials. The physical mechanism is the depolarization electric field determined by the gradient of chemical composition “x”. The field lowers the steepness of the switching barrier in the otherwise unswitchable parts of the compositionally graded AlN-Al 1-x Sc x N and ZnO-Zn 1-x Mg x O structures. In the MgO-like regions of the compositionally graded MgO-Zn 1-x Mg x O structure, a shallow double-well free energy potential emerges. Proximity ferroelectric switching of the compositionally graded structures placed in the probe-electrode geometry occurs due to nanodomain formation under the tip. We predict that a gradient of chemical composition “x” significantly lowers effective coercive fields of the compositionally graded AlN-Al 1-x Sc x N and ZnO-Zn 1-x Mg x O structures compared to the coercive fields of the corresponding multilayers with a uniform chemical composition in each layer. A tip-induced switching further lowers the coercive field, enabling control of ferroelectric domains in otherwise unswitchable compositionally graded structures, which can provide nanoscale domain control for memory, actuation, sensing, and optical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Resonant acoustic monitoring of damage in plug‐screw feeders

Abstract Plug‐screw feeders are critical in many industrial processes for compressing slurry materials via a rotating plug‐screw feeder. Over time, increasing plug‐screw feeder wear will eventually lead to catastrophic mechanical failure. Early detection of the wear state can prevent unplanned catastrophic failures resulting in operational shut‐downs, costly repairs, and most importantly the health and safety of workers. We present a theoretical basis for a noninvasive, in operando acoustic resonant technique to monitor the wear state of plug‐screw feeders. The technique is based on tracking the resonant acoustic modes of the plug‐screw feeder, which are sensitive to the plug‐screw feeder geometry, material, and operating conditions. We implemented a multivariate polynomial model to estimate the plug‐screw feeder wear state using multiple acoustic resonances by simulating the acoustic resonant modes for two categories of wear (tip and thread damage) that are common in plug‐screw feeders. Fitting multiple resonances to the polynomial model, we demonstrate accurate estimation of the total mass loss, as well as characterization of the type of damage (i.e., tip vs. thread). Current approaches for monitoring plug‐screw feeder wear rely on shutting down the operation and visually inspecting the plug‐screw feeder. The presented acoustic technique offers a noninvasive, in operando measurement approach that mitigates unplanned catastrophic failures. The acoustic resonance technique presented in the paper has a broad range of industrial applications including the Pharmaceutical, Mining, Integrated Biorefineries (IBR), and Additive Manufacturing industries, to name a few.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Atomic Fingerprinting of Heteroatoms Using Noncontact Atomic Force Microscopy

We report immense strides have been made in increasing the resolution of scanning probe microscopy. Noncontact atomic force microscopy (n-AFM) now offers one the ability to characterize and visualize single molecules with subatomic resolution. Specifically, nc-AFM with a carbon monoxide (CO) functionalized tip has the ability to discriminate functional groups (–C≡C–, –CH 2 , –C$=$O, …), although discriminating atomic species often remains as an ongoing challenge. Here, real-space pseudopotentials constructed within density functional theory are employed to accurately simulate nc-AFM images of molecules containing heteroatoms (S, I, and N) within dibenzothiophene (DBT), 2-iodotriphenylene (ITP), acridine (ACR) and ferrous phthalocyanine (FePc). It is found that S and I atoms can be easily identified from C based on their unique features. For N atoms, a use of tip functionalization is proposed to effectively discriminate them from C atoms.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Gravo-aeroelastic scaling of a 13-MW downwind rotor for 20% scale blades

A 105-m, 13-MW two-bladed downwind Segmented Ultralight Morphing Rotor (SUMR-13) blade was gravo-aeroelastically scaled by 20% to a 20.87-m-long demonstrator blade and confirmed through structural ground testing. The subscale model was achieved through geometric scaling and by aeroelastic scaling principles based on operational flapwise deflections combined with rotational and structural frequencies while retaining the turbine tip-speed ratio. In particular, the subscale demonstrator was designed to replicate, as closely as possible, the nondimensional geometry, the ratio of centrifugal to gravitational moments, the tip-speed ratio, and the nondimensional rotation rate. The intent for this demonstrator was to achieve the same nondimensional flapwise blade deflections and dynamics of the full-scale 13-MW rotor. The manufactured SUMR-D blade resulted in less than half of the mass of the conventional two-bladed Controls Advanced Research Turbine (CART2) rotor blade based on scaling and a lower power rating, though with some differences in mass and stiffness from the ideal scaled-down design to meet safety requirements at the test site. To achieve proper scaling, operational pitch control set points were altered to account for the differences by evaluating simulated operation of both the SUMR-13 and SUMR-D rotors. Structural testing of the SUMR-D blade investigated the response to well-defined flapwise loads and indicated that the subscale blade had the appropriate elastic properties needed for both scaling and for safe operational field testing.

17 WIND ENERGY↗
DOE OSTI2025

Control of machining-induced residual stress via tool geometry and process parameter modification

Distortion generated in machined, monolithic, thin-walled aerospace components due to residual stresses leads to significant material and economic waste in the manufacturing industry. Inherent residual stress (IRS) present in stock materials combines with machining-induced residual stress (MIRS) to influence the final machined part distortion. It is hypothesized that MIRS can be controlled, based on the part geometry, through deliberate cutting tool geometry and process parameter modifications to negate the effect of IRS on distortion, consequently resulting in distortion-free parts. A finite element (FE) orthogonal cutting model is developed to study how tool geometry and process parameters influence machining-induced residual stress (MIRS). Orthogonal cutting experiments are performed on Al 7075-T651 samples to measure cutting forces and MIRS. A cutting force dynamometer is used to measure forces during cutting and a novel digital image correlation (DIC) based hole drilling technique is employed to measure the near-surface residual stress (RS) in the cut samples. These data are subsequently utilized to validate the FE prediction model. Various cases of cutting simulations involving different depths of cut, tool tip radii, and rake angles are performed to study their effects on RS. Similar to prior literature, increasing the depth of cut, tool tip radius, or rake angle is found to promote the formation of near-surface tensile stresses. The competing effects of material plowing and temperature are shown to determine the type of RS at the end of the cut. Moreover, a window of variation of RS (up to ± 400 MPa) is estimated within the given range of conditions, allowing for the control of MIRS through tool and process modification.

Mathews, Ritin [ORNL] (ORCID:0000000301440828)↗
DOE OSTI2023

In situ embedment of type K sheathed thermocouples with directed energy deposition

Advanced nuclear reactor systems require new technologies for heat transfer and system monitoring. Additive manufacturing (AM) offers the design flexibility to allow in-situ sensor embedment through smart manufacturing for real-time monitoring, and performance of these systems. Here, this study focuses on experiments investigating the feasibility of in-situ sensor embedment using directed energy deposition (DED). Type K thermocouples are embedded into 316L stainless steel (SS) samples using two different configurations (e.g., exposed and embedded tips) and two designs (e.g., flush to substrate) within an AM base. Embedded sensor samples are analyzed via in-situ measurements and high-temperature performance validation tests at 350ºC and 900ºC. Temperature performance results at both temperature tests show good agreement with manufacturer specifications proving that these sensors could still capture accurate temperature readings after in-situ embedment during DED processing. An additional optimization experiment was conducted on the exposed tip configuration using a surrogate thermocouple to improve tolerances and the embedment process. Results improved tolerances, lower porosity, smaller gaps between the sensor and base, and better junction contact for the sensor. Although further optimization of this embedment strategy is necessary to improve the structural stability and tolerances within the component, this research strategy provides a proof-of-feasibility for DED embedment with commercial sheathed thermocouples. This research provides early impact on embedment of sensor for multiple materials and complex geometric components..

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2020

Nanomechanical sampling of material for nanoscale mass spectrometry chemical analysis

The ability to spatially resolve the chemical distribution of compounds on a surface is important in many applications ranging from biological to material science. To this extent, we have recently introduced a hybrid atomic force microscopy (AFM)-mass spectrometry (MS) system for direct thermal desorption and pyrolysis of material with nanoscale chemical resolution. However, spatially resolved direct surface heating using local thermal desorption becomes challenging on material surfaces with low melting points, because the material will undergo a melting phase transition due to heat dissipation prior to onset of thermal desorption. Therefore, here we developed an approach using mechanical sampling and collection of surface materials on an AFM cantilever probe tip for real-time analysis directly from the AFM tip. This approach allows for material to be concentrated directly onto the probe for subsequent MS analysis. We evaluate the performance metrics of the technique and demonstrate localized MS sampling from a candelilla wax matrix containing UV stabilizers avobenzone and oxinoxate from areas down to 250 nm × 250 nm. Overall, this approach removes heat dissipation into the bulk material allowing for a faster desorption and concentration of the gas phase analyte from a single heating pulse enabling higher signal levels from a given amount of material in a single sampling spot.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Amino mapping: possibility to visualize amino-N compounds in the rhizosphere of Zea Mays L.

Abstract Understanding N uptake by plants, the N cycle, and their relationship to soil heterogeneity has generated a great deal of interest in the distribution of amino-N compounds in soil. Visualization of the spatial distribution of amino-N in soil can provide insights into the role of labile N in plant-microbial mechanisms of N acquisition and plant N uptake, but until now, it has remained technically challenging. Here, we describe a novel technique to visualize the amino-N distribution at the root-soil interface. The technique is based on time-lapse amino mapping (TLAM) using membranes saturated with the fluorogenic OPAME reagent (O-phthalaldehyde and β-mercaptoethanol). OPAME in the membrane reacts with organic compounds containing a NH 2 functional group at the membrane-soil interface, generating a fluorescent product visible under UV light and detectable by a digital camera. The TLAM amino-mapping technique was applied to visualize and quantify the concentration of amino-N compounds in the rhizosphere of maize (Zea MaysL.). A ten times greater amino-N concentration was detected in the rhizosphere compared to non-rhizosphere soil. The high content of amino-N was mainly associated with the root tips and was 3 times larger than the average amino-N content at seminal roots. The amino-N rhizosphere was 2 times broader around the root tips than around other parts of the roots. We concluded that TLAM is a promising approach for monitoring the fate of labile N in soils. However, the technique needs to be standardized for different soil types, plant species, and climate conditions to allow wider application.

Agriculture↗
DOE OSTI2020

Interfacial toughness: dependence on surface roughness and test temperature

Interfacial toughness quantifies resistance to crack growth along an interface and in this investigation the toughness of an aluminum/epoxy interface was measured as a function of surface roughness and test temperature. The large strain response of the relatively ductile epoxy adhesive used in this study was also characterized. This epoxy adhesive exhibits intrinsic strain-softening after initial compressive yield and then deforms plastically at a roughly constant flow stress until it rapidly hardens at large compressive strains. Here, we find that interface toughness scales as the product of the temperature dependent epoxy yield strength and a length scale that characterizes surface roughness. The proposed scaling is based upon dimensional considerations of a model problem that assumes that the characteristic length scale of both the roughness and the crack-tip yield zone is small relative to the region dominated by the linear elastic asymptotic crack-tip stress field. Furthermore, the model assumes that interfacial failure occurs only after the epoxy begins to harden at large strains. The proposed relationship is validated by our interfacial toughness measurements.

36 MATERIALS SCIENCE↗

Refine your search to explore more results.