Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Thrusters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Modeling arcjet space thrusters

The UTSI arcjet model is used to compare the performance of a hydrogen and an ammonia arcjet in the same configuration and at the same electrical power. The predicted specific impulse is 50 percent higher for the hydrogen propellant. Numerical studies made of the effect of transport properties on the performance of a hydrogen arcjet indicate that diffusive transport is very significant even in the supersonic part of the flow, and that relatively small changes in transport properties can have a significant effect on performance. These studies also show that nonequilibrium recombination chemistry can have a large effect on the transport coefficients. This leads to the conclusion that finite rate chemical calculations are necessary if accurate arcjet performance is to be calculated.

Rhodes, Robert↗
NASA NTRS1991

Analysis of a swirl stabilized arcjet thruster

Viscous swirling flow through transonic converging-diverging nozzles (with and without centerbodies) is examined numerically. An implicit technique is used to solve the axisymmetric Thin Layer Naiver-Stokes equations. The effect of swirl and viscosity on low Reynolds number flows is shown by examining integral parameters and flowfield details.

Keith, Theo G., Jr.↗
NASA NTRS1991

A Navier-Stokes Solution of Hull-Ring Wing-Thruster Interaction

Navier-Stokes simulations of high Reynolds number flow around an axisymmetric body supported in a water tunnel were made. The numerical method is based on a finite-differencing high resolution second-order accurate implicit upwind scheme. Four different configurations were investigated, these are: (1) barebody; (2) body with an operating propeller; (3) body with a ring wing; and (4) body with a ring wing and an operating propeller. Pressure and velocity components near the stern region were obtained computationally and are shown to compare favorably with the experimental data. The method correctly predicts the existence and extent of stern flow separation for the barebody and the absence of flow separation for the three other configurations with ring wing and/or propeller.

Yang, C.-I.↗
NASA NTRS1991

A study of ignition and simulation circuits for arcjet thrusters, part 1

A 1 kW electronic load was programmed to simulate the nonlinear i-v (volt-ampere) characteristics of an arcjet, both ignited and unignited. The simulator was tested and found to closely resemble an arcjet both for large transients and small perturbances up to about 40 kHz. No attempt was made to simulate the ignition process itself. The dynamic behavior of the arcjet (and the simulator) was shown to differ significantly from that of a resistor bank. Previous research led to the design and construction of a 1 kW arcjet power supply. A high voltage ignition circuit was added to this hardware, and tests on a 1 kW arcjet were performed at NASA-Lewis. All tests were successful and no ignition failures were observed. Circuit documentation and test results are included.

Stuart, Thomas A.↗
NASA NTRS1991

Modeling of life limiting phenomena in the discharge chamber of an electron bombardment ion thruster

An experimental facility to study the low energy sputtering of metal surfaces with ions produced by an ion gun is described. The energy of the ions ranged from 10 to 500 eV. Cesium ions with energies from 100 to 500 eV were used initially to characterize the operation of the ion gun. Next, argon and xenon ions were used to measure the sputtering yields of cobalt (Co), Cadmium (Cd), and Chromium (Cr) at an operating temperature of 2x10(exp -5) Torr. The ion current ranged from 0.0135 micro-A at 500 eV. The targets were electroplated on a copper substrate. The surface density of the electroplated material was approx. 50 micro-g/sq cm. The sputtered atoms were collected on an aluminum foil surrounding the target. Radioactive tracers were used to measure the sputtering yields. The sputtering yields of Cr were found to be much higher than those of Co and Cd. The yields of Co and Cd were comparable, with Co providing the higher yields. Co and Cd targets were observed to sputter at energies as low as 10 eV for both argon and xenon ions. The Cr yields could not be measured below 20 eV for argon ions and 15 eV for xenon ions. On a linear scale the yield energy curves near the threshold energies exhibit a concave nature.

Handoo, Arvind K.↗
NASA NTRS1991

Aerodynamic design of a Coanda induced force and thruster anti-torque system

A general method of analysis of the external and internal aerodynamics of a generic Coanda induced circulation anti-torque system is presented. The technique gives moment about the yaw axis and download induced on the boom as well as the force developed by an aft jet. The external flows including downwash, wake swirl and the boom circulation are considered. The internal flow and losses through the duct, fan, blown slots, cascades and nozzle are considered on a step-by-step basis. Limited comparison is made with open data where available.

Velkoff, Henry R.↗
NASA NTRS1992

Extended testing of xenon ion thruster hollow cathodes

A hollow cathode wear-test of 508 hours was successfully completed at an emission current of 23.0 A and a xenon flow rate of 10 Pa-L/s. This test was the continuation of a hollow cathode contamination investigation. Discharge voltage was stable at 16.7 V. The cathode temperature averaged 1050 C with a 7 percent drop during the wear-test. Discharge ignition voltage was found to be approximately 20 V and was repeatable over four starts. Post-test analyses of the hollow cathode found a much improved internal cathode condition with respect to earlier wear-test cathodes. Negligible tungsten movement occurred and no formation of mono-barium tungstate was observed. These results correlated with an order-of-magnitude reduction in propellant feed-system leakage rate. Ba2CaWO6 and extensive calcium crystal formation occurred on the upstream end of the insert. Ba-Ca compound depositions were found on the Mo insert collar, on the Re electrical leads, and in the gap between the insert and cathode wall. This wear-test cathode was found to be in the best internal condition and had the most stable operating performance of any hollow cathode tested during this contamination investigation.

Sarver-Verhey, Timothy R.↗
NASA NTRS1992

Electrostatic ion thruster optics calculations

Calculations have been performed which encompass both a self-consistent ion source extraction plasma sheath and the primary ion optics including sheath and electrode-induced aberrations. Particular attention is given to the effects of beam space charge, accelerator geometry, and properties of the downstream plasma sheath on the position of the electrostatic potential saddle point near the extractor electrode. The electron blocking potential blocking is described as a function of electrode thickness and secondary plasma processes.

Whealton, John H.↗
NASA NTRS1992

Extended-testing of xenon ion thruster hollow cathodes

A hollow cathode wear-test of 508 hours was successfully completed at an emission current of 23.0 A and a xenon flow rate of 10 Pa-L/s. This test was the continuation of a hollow cathode contamination investigation. Discharge voltage was stable at 16.7 V. The cathode temperature averaged 1050 C with a 7 percent drop during the wear-test. Discharge ignition voltage was found to be approximately 20 V and was repeatable over four starts. Post-test analyses of the hollow cathode found a much improved internal cathode condition with respect to earlier wear-test cathodes. Negligible tungsten movement occurred and no formation of mono-barium tungsten was observed. These results correlated with an order-of-magnitude reduction in propellant feed-system leakage rate. Ba2CaWO6 and extensive calcium crystal formation occurred on the upstream end of the insert. Ba-Ca compound depositions were found on the Mo insert collar, on the Re electrical leads, and in the gap between the insert and cathode wall. This wear-test cathode was found to be in the best internal condition and had the most stable operating performance of any hollow cathode tested during this contamination investigation.

Sarver-Verhey, Timothy R.↗
NASA NTRS1992

Planar laser-induced fluorescence imaging of OH in the exhaust of a bi-propellant thruster

Planar laser-induced fluorescence imaging of the hydroxyl radical has been performed on the flow produced by the exhaust of a subscale H2/O2 fueled bi-propellant rocket engine. Measurements were made to test the feasibility of OH (0,0) and (3,0) excitation strategies by using injection seeded XeCl and KrF excimer lasers, respectively. The flow is produced with hydrogen and oxygen reacting at a combustor chamber pressure of 5 atm which then exhausts to the ambient. The hydroxyl concentration in the exhaust flow is approximately 8 percent. Fluorescence images obtained by pumping the Q1(3) transition in the (0,0) band exhibited very high signals but also showed the effect of laser beam absorption. To obtain images when pumping the P1(8) transition in the (3,0) band it was necessary to use exceptionally fast imaging optics and unacceptably high intensifier gains. The result was single-shot images which displayed a signal-to-noise ratio of order unity or less when measured on a per pixel basis.

Paul, Phillip H.↗
NASA NTRS1992

Los Alamos research in nozzle based coaxial plasma thrusters

The topics are presented in viewgraph form and include the following: research approach; perspectives on efficient magnetoplasmadynamic (MPD) operation; NASA and DOE supported research in ideal magnetohydrodynamic plasma acceleration and flow, electrode phenomena, and magnetic nozzles; and future research directions and plans.

Scheuer, Jay↗
NASA NTRS1992

Recent advances in MPD thruster research at Princeton

A summary of last years anode, plasma, and cathode findings is presented. A summary of this years activities and findings is also presented. A brief discussion of previous and current understanding is given and covers the following topics: existence of microinstabilities; the scaling of Va with the Hall parameter; the scaling of anomalous resistivity with the Hall parameter; the relation between anomalous resistivity and the anode drop; the presence of turbulence in the anode region; numerical simulation with anomalous transport; the use of magnets to decrease dissipation; performance testing with the new anode; the mechanisms behind the ionization sink; and lithiated cathode research.

Jahn, Robert G.↗
NASA NTRS1993

Experimentation in the low-density plume of a simulated electrothermal thruster for computer code validation

Pressures and flow angles are measured in the plume of a 20 deg half-angle, conical nozzle in vacuum with Pitot tubes and conical probes. The area of measurement in the plume ranges from the nozzle exit plane to 480 mm axially downstream and from the plume centerline to 60 mm radially. The nozzle has an exit-to-throat area ratio of 100:1 and a throat diameter of 3.2 mm. The nozzle flow exhausts to a vacuum of order 10(exp -2) Pa to simulate a resistojet (an electrothermal rocket of less than 1 N of thrust) operating in space. Experimental data are given for flows of nitrogen at 55 and 68 mg/s, stagnation temperatures between 695 and 921 K, and stagnation pressures ranging from 5600 to 7100 Pa. Data are also given for argon at a rate of 68 mg/s, a stagnation temperature of 648 K, and stagnation pressures of 4500, 4750, and 4770 Pa. Measurements in the nitrogen plume are compared with computational results from a direct-simulation Monte Carlo method.

Meissner, Dana L.↗
NASA NTRS1993

Innovative electric propulsion thruster modeling

The objective of this program is to model and evaluate advanced nuclear electric propulsion (NEP) system concepts as an aid to the performance of NEP mission benefits studies. The two primary goals are as follows: (1) provide scaling relationships for mass, power, and efficiency, as functions of Isp, propellant type, and other important quantities. The discussion is presented in vugraph form.

Frisbee, Robert H.↗

Refine your search to explore more results.