SEARCH · Engineering Papers

Results for “System study”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

All sources NASA NTRS DOE OSTI

NASA NTRS2015

Handling Qualities of Large Rotorcraft in Hover and Low Speed

According to a number of system studies, large capacity advanced rotorcraft with a capability of high cruise speeds (approx.350 mph) as well as vertical and/or short take-off and landing (V/STOL) flight could alleviate anticipated air transportation capacity issues by making use of non-primary runways, taxiways, and aprons. These advanced aircraft pose a number of design challenges, as well as unknown issues in the flight control and handling qualities domains. A series of piloted simulation experiments have been conducted on the NASA Ames Research Center Vertical Motion Simulator (VMS) in recent years to systematically investigate the fundamental flight control and handling qualities issues associated with the characteristics of large rotorcraft, including tiltrotors, in hover and low-speed maneuvering.

Large Rotorcraft↗

NASA NTRS2016

NASA Environmentally Responsible Aviation's Highly-Loaded Front Block Compressor Demonstration

This presentation will detail the work done to improve thermal efficiency in the compression process of a gas turbine engine for aircraft applications under NASAs Environmentally Responsible Aviation Project. The talk will present the goals and objectives of the work and show the activity of both Phase 1 and Phase 2 tests and analysis. The summary shows the projected fuel burn savings achieved through system studies.

ERA↗

NASA NTRS2015

K2 & Solar System Science

All of the fields that K2 observes are near the ecliptic plane in order to minimize the spin-up of the spacecraft in response to the effects of solar irradiation. The fields observed by K2 are thus rich in Solar System objects including planets, asteroids and trans-Neptunian objects (TNOs). K2 has already performed observations of Neptune and its large moon Triton, 68 Trojan and Hilda asteroids, 5 TNOs (including Pluto) and Comet C/2013 A1 (Siding Springs). About 10,000 main-belt asteroids that fell into the pixel masks of stars have been serendipitously observed. Observations of small bodies are especially useful for determining rotation periods. Uranus will be observed in a future campaign (C8), as will many more small Solar System bodies. The status of various K2 Solar System studies will be reviewed and placed within the context of our current knowledge of the objects being observed.

trans-Neptunian objects (TNOs).↗

NASA NTRS2016

Usage of Multi-Mission Radioisotope Thermoelectric Generators (MMRTGs) for Future Potential Missions

The goal of NASAs Radioisotope Power Systems (RPS) Program is to make RPS ready and available to support the exploration of the solar system in environments where the use of conventional solar or chemical power generation is impractical or impossible to meet the needs of the missions. To meet this goal, the RPS Program, working closely with the Department of Energy, performs mission and system studies (such as the recently released Nuclear Power Assessment Study), evaluates the readiness of promising technologies to infuse in future generators, assesses the sustainment of key RPS capabilities and knowledge, forecasts and tracks the Programs budgetary needs, and disseminates current information about RPS to the community of potential users. This presentation focuses on the needs of the mission community and provides users a better understanding of how to integrate the MMRTG (Multi-Mission Radioisotope Thermoelectric Generator).

Radioisotope↗

NASA NTRS2016

NASA Jet Noise Research

The presentation highlights NASA's jet noise research for 2016. Jet-noise modeling efforts, jet-surface interactions results, acoustic characteristics of multi-stream jets, and N+2 Supersonic Aircraft system studies are presented.

reduction↗

NASA NTRS2017

Flow and Noise From Septa Nozzles

This investigation pertains to distributed propulsion system. Basically, the jet exhaust is divided and channeled through multiple compartments or septa. In one version of the concept each septum is to be driven by an electric fan, the power being supplied by engines suitably mounted on the airframe. In the latter hybrid case the need for heavy power trains is eliminated and system studies indicate a net benefit in efficiency. From aeroacoustics point of view, however, there are concerns. An immediate question is whether the noise from the multiple jets would be equal to or greater than that from an equivalent single jet. When multiple jets are placed side by side sometimes they resonate and produce more noise. In order to address these issues a fundamental model-scale experiment is being carried out at NASA Glenn Research Center (GRC). Preliminary results from this study have been presented recently. One of the key findings is that the noise from the septa nozzle can actually be less than that from the equivalent single nozzle. Continued studies make it clear that the flow from the septa nozzle may be quite sensitive to upstream passage geometry in each septum. This can have a profound impact on the evolution of the flow downstream as well as noise. These issues are currently being researched. The proposed paper is to summarize the results from the mainly experimental study that is to be aided by limited numerical simulation.

nozzle flow↗

NASA NTRS2018

Payload Sensitivities for Human Mars Exploration Transportation Systems

NASA is continuing to investigate mission and transportation system alternatives to support human exploration of Mars. Several publications over the last few years have outlined, in detail, the baseline reference architectures under consideration. These alternatives include SEP-Chemical Hybrid Propulsion Systems, oxygen/methane propulsion stages, and nuclear thermal propulsion systems. Studies to date have focused on identifying mission architectures that leverage these different transportation options to best support a Mars mission within the context of overarching guidelines and constraints. The focus on identifying "closed" reference mission architectures for these transportation options is a key first step in comparing alternatives and supporting the development of technology investment strategies. Architecture closure implies that the architecture identified provides a viable solution which meets all constraints and closely aligns with guidelines. If a viable architecture cannot be identified for a given transportation option, there is no need to continue investigating that option. However, at this early stage of architecture development, metrics of comparison should look beyond how these architectures perform relative to the baseline reference mission. Architectural robustness, or an insensitivity to requirements drift, should also be considered in any comparison of architectures. At this early stage of design, mission requirements have the potential to change as more definition is provided and more analyses are completed. Particularly in relation to the mass of transported elements, including Mars landers and crew habitat, it is recognized that as designs for these elements mature there exists the potential for mass growth. Selection of an architecture alternative carries with it programmatic risks and relative sensitivity to mass growth can provide insight into a particular architecture option's risk of being unable to complete its mission without significant redesign as more element definition is provided. This paper outlines the current understanding of the sensitivity

Percy, Thomas K.↗

NASA NTRS2019

Noise Measurements of a Low-Noise Top-Mounted Propulsion Installation for a Supersonic Airliner

A model-scale exhaust system was tested to validate low-noise concepts and noise prediction methods. The tests involved far-field acoustics, translating phased array, and particle image velocimetry; this report covers the far-field acoustic measurements. Data were acquired for a series of nozzles with different chevron designs, both uninstalled and installed on a representative aircraft planform. The impact of the various chevron treatments on the far-field noise was documented, along with the impact of the pylon and planform. For the baseline nozzle, installation produced a 2EPNdB reduction, as assumed in system studies. Chevrons were used to shift noise sources upstream to maximize the installation benefits and to reduce unshielded sources downstream. These resulted in reductions of 4-5EPNdB relative to the uninstalled baseline nozzle. Detailed analysis of spectral directivities behind the integrated EPNL metric gave insight into how well these concepts actually work. When correlated with particle image velocimetry measurements and phased array measurements, reported in companion papers, the explanation of acoustic benefits from top-mounted propulsion is clear as is the path toward optimization of the concept.

Supersonics↗

NASA NTRS2019

PIV/Phased Array/Far-Field Noise Measurements of a Low-Noise Top-Mounted Propulsion Installation for a Supersonic Airliner

Bridges, James↗

NASA NTRS2016

Mars Sample Thermal Control During Mars Ascent and Orbit

Although NASA has no official plans at this time for a mission to return samples from Mars, the Program Formulation Office of the Mars Exploration Program sponsors ongoing mission concept studies, systems analyses, and technology investments which explore different strategies for the potential return of samples from Mars, consistent with the charter of the program and stated priorities of the science community. Maintaining the thermal integrity of collected samples would be very important. In general, samples would be collected, sealed inside tubes, and left on the surface for later retrieval. They would then be inserted into an OS (Orbiting Sample), and carried to a Mars or Solar orbit via a MAV (Mars Ascent Vehicle). Subsequently, an Earth return vehicle would rendezvous with the OS and bring it back to Earth. During ascent from Mars, the OS could serve as the nose cone of the MAV and would be subjected to significant aerodynamic heating from the Martian atmosphere. Once the OS is released from the MAV, its external surface would be exposed to potentially several years of sunlight, eclipse, planetary IR, albedo, and space. The challenge is to ensure that these samples are kept at thermally moderate conditions to preserve their integrity in these widely different environments. Various thermal techniques have been investigated to achieve sample thermal control: use of thermal protection shields and surfaces (ablative and non-ablative) to protect them from adverse exposure to ascent heating, as well combinations of thermo-optical coatings during the orbital phase. The work described herein is part of this ongoing effort & will describe the key challenges related to the thermal control of the potential Mars samples during these phases and the corresponding schemes to overcome them.

Bhandari, Pradeep↗

NASA NTRS2017

Technology Development Plan and Preliminary Results for a Low Temperature Hybrid Mars Ascent Vehicle Concept

A hybrid propulsion system is being considered for a potential Mars Ascent Vehicle (MAV) based on its low temperature capability, ability to restart and high performance. The hybrid’s ability to survive in low and variable temperatures reduces power requirements and therefore system mass. Its ability to restart enables a Single Stage to Orbit (SSTO) design, minimizing system complexity. The hybrid’s high-performance (approximately 314 s Isp (I (sub sp)) (specific impulse in seconds) leads to a low total Gross Lift Off Mass (GLOM). These advantages set the hybrid design above the alternatives in the system studies completed at JPL (Jet Propulsion Laboratory). However, this solution has the lowest Technology Readiness Level (TRL) of the propulsion options. Therefore, a technology development effort has been undertaken to raise the TRL of the hybrid option and potentially enable its infusion into a future MAV or other in-space application. The culmination of this technology development is a flight demonstration, which is currently in the planning phases for launch in the early 2020’s.

Karp, Ashley↗

NASA NTRS2019

Experimental Facility to Measure Power and Forces to Excavate Lunar Regolith Simulants

An Excavation Lab has been built at the NASA Glenn Research Center in support of the NASA In-Situ Resource Utilization (ISRU) program objectives to measure the power and forces needed to excavate granular lunar regolith. The data obtained will be used to validate excavation models used in system studies and for developing light weight, energy efficient digging devices for activities on the moon and mars. The Excavation Lab houses the Advanced Planetary Excavator (APEX), an electrically actuated backhoe arm with a bucket, which is used to dig GRC-3B, a simulant of granular lunar regolith comprised of silica sand and silt. A load cell is mounted between the arm and the bucket to measure digging forces. Dig trajectories files are created and used to control the APEX for repeatability. Comparison of preliminary data recorded for the same trajectory in air and in GRC-3B shows measurable difference in power and load cell measurements. Load cell forces for a linear dig in GRC-3B are presented.

Excavation↗

NASA NTRS2019

Aerodynamic and Aerothermal Simulations of Mars Concept Vehicles Using Overset DPLR

NASA's Descent System Studies (DSS) Program is studying various concept vehicles to enable landing of heavy payloads on the surface of Mars. While it is desirable to run high-fidelity CFD simulations to accurately assess the aerodynamic and aerothermal effects of various design changes during EDL, it is usually difficult to quickly generate high-quality grids suitable for such analyses. One approach to address this bottleneck in mesh generation is through the use oversetting grids. Although the overset approach is efficient and powerful in solving partial differential equations on complex geometries, new users often find it challenging to apply overset concepts for their simulations. For example, generating hyperbolic grids with sufficient overlap; priority in hole-cutting on multiple overlapping grids; and fixes to assemble overlapping viscous grids at the body surface. The objective of this presentation is to introduce a simple process that combines the advantages of near-body, point-matched, structured grids with oversetting background grids suitable for grid alignment. This approach allows for grids that can be sequenced, reclustering of mesh spacing at the wall, and grid alignment with the bow shock. The current methodology is tested on a Mid-L/D configuration using the overset DPLR code.

Overset Grids↗

NASA NTRS2019

Materials and Processes for New Propulsion Systems with Reduced Environmental Impact

Aeronautics research at NASA Glenn Research Center includes development, characterization and modeling of high temperature, lightweight materials and fabrication processes for aircraft propulsion systems with increased efficiency and reduced emissions, fuel burn and noise. Current propulsion materials research includes Ceramic Matrix Composites and Environmental Barrier Coatings, Polymer Matrix Composites and Additive Manufacturing processes. This presentation will summarize recent progress and plans in these areas. Ceramic Matrix Composites for Turbine Components: As part of NASA's Aeronautics research, Glenn Research Center has developed Ceramic Matrix Composites for 2700 degrees Fahrenheit turbine engine applications in the next generation of ultra-efficient aircraft. In this presentation, the development of advanced fiber and matrix constituents that enabled this advancement will be reviewed, and characterization of the resulting improvements in mechanical properties and durability will be summarized. Progress toward the development and validation of models predicting the effects of the engine environment on durability of Ceramic Matrix Composites and Environmental Barrier Coatings will be summarized. Progress and plans for collaborative research with industry and other government agencies will be reviewed. Polymer Matrix Composites for Powertrain and Impact Protection: A lightweight, hybrid polymer matrix composite/steel gear concept for rotorcraft power transmission applications was evaluated at realistic speed, torque, and power conditions. Dynamic testing was performed at 5000 horsepower and 5400 revolutions per minute with no performance degradation. Test results demonstrated the potential of hybrid composite / metal gears to reduce gear weight by approximately 15 percent, enabling the implementation of multi-speed drive systems, which would otherwise have a weight penalty, for increased speed and efficiency. Results of post-test inspection and endurance tests will be presented. Separately, ballistic impact tests demonstrated improved damage tolerance in polymer matrix composites by incorporating lightweight, thermoplastic veil materials between selected composite plies during the composite fabrication process. Results of impact tests and post-test inspection will be presented. Additive Manufacturing for Electric Propulsion: Additive Manufacturing processes offer the potential to fabricate new, high power density electric motor designs with complex geometries, multi-material components and optimally designed components that would not be feasible with traditional manufacturing processes. High performance stator components using advanced 3-phase conductive coils were fabricated using direct printing with optimized silver pastes. Additional additive manufacturing methods are being used to fabricate rotors and motor housing components. Systems studies show that the higher performance and lower weight motors offer improved energy efficiency and reduced emissions. Improvements to motor performance resulting from optimized materials and component designs will be presented.

Additive Manufacturing↗

NASA NTRS2019

Modern Aerocapture Guidance to Enable Reduced-Lift Vehicles at Neptune

Aerocapture is covered extensively in the literature as means of achieving orbital insertion with dramatic mass-saving results compared to fully-propulsive systems. One of the primary obstacles facing aerocapture is the inherent uncertainty associated with passing through a planet’s upper atmosphere. In-flight dispersions due to delivery errors, environment variables, and aerodynamic performance impose a large flight envelope. System studies for aerocapture often select high lift-to-drag ratios to compensate for these uncertainties. However, modern predictor-corrector guidance strategies have shown promise in recent years to provide robust control schemes in-situ. These algorithms do not rely on a pre-calculated reference trajectory and instead employ a numerical optimizer to continuously solve nonlinear equations of motion each guidance cycle. Numerical predictor-corrector strategies may provide considerable accuracy over heritage guidance schemes. The goal of this study is reproduce a landmark study of Neptune aerocapture and apply modern guidance to illustrate relative performance improvements and cost-saving potential. Capture constraints based on the theoretical corridor width are considered. Results indicate that heritage vehicles with moderate lift-to-drag ratios, lower than previous studies have indicated, may prove viable for aerocapture at Neptune.

Heidrich, C. R.↗

NASA NTRS2010

TPSAS-NF1676L-11152-DND

The Committee on Earth Observation Satellites (CEOS) Systems Engineering Office (SEO) will present a systems study report on Land Surface Imaging.

Brian D Killough↗

NASA NTRS2011

HyspIRI Level-2 Thermal Infrared (TIR) land surface temperature and emissivity algorithm theoretical basis document.

This document outlines the theory and methodology for generating the HyspIRI TIR Level-2 land surface temperature and emissivity (LST&E) products. The LST&E products are derived from the surface radiance product that is calculated by atmospherically correcting the at-sensor radiance, making them interdependent products. LST&E products are essential for a wide range of Earth system studies.

Hook, Simon J.↗

NASA NTRSDate not supplied

Suborbital Lunar Gravity Experiment of an Electrodynamic Regolith Conveyor

NASA’s Swamp Works Electrostatics and Surface Physics Laboratory (ESPL) is planning to test a 4-phase electrodynamic regolith conveyor in simulated lunar gravity on a suborbital flight in 2023. A 4-phase electrodynamic regolith conveyor could convey regolith without the risk of rotating or vibratory actuation, which could jam or require regular maintenance due to the abrasive nature of lunar regolith. Another advantage of electrodynamic conveying is the reduction of conveying power, which is important considering the limited scale of available early-stage lunar power systems. The current state of the art(SOA) for lunar regolith conveying is based on recent NASA system studies for oxygen production plants. These plant designs require conveying rates around 100 kg/hr, to produce 10 mT/yr of oxygen from the regolith. To accomplish this, conventional augers and vibratory spiral conveyors have been identified as the SOA or the leading candidates due to their extensive use in the terrestrial material handling industry. At NASA KSC, the use of dynamic electric fields, generated by alternating high voltage on electrodes, has been developed as a dust mitigation solution known as the Electrodynamic Dust Shield (EDS). The EDS is being developed for lenses, solar panels, radiators, fabric and seals. ESPL researchers have shown the ability to move thin layers (~ a few mm) of dust with mW of power. In Academia, researchers have shown the ability to electrodynamically convey regolith up to ~1 kg/hr with a4-phase EDS and electromagnetically convey particles that would suggest a lunar regolith conveying rate of ~25 kg/hr. This paper will describe the design and expected operation of a 4-phase electrodynamic regolith conveyor in lunar gravity. This paper will also describe how an electrodynamic conveyor could be scaled for transporting ISRU relevant flow rates.

Aaron D S Olson↗

Refine your search to explore more results.