Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STIRRING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

THE NEED FOR A NEW JOINING TECHNOLOGY FOR THE CLOSURE WELDING OF RADIOACTIVE MATERIALS CONTAINERS

One of the activities associated with cleanup throughout the Department of Energy (DOE) complex is packaging radioactive materials into storage containers. Much of this work will be performed in high-radiation environments requiring fully remote operations, for which existing, proven systems do not currently exist. These conditions demand a process that is capable of producing acceptable (defect-free) welds on a consistent basis; the need to perform weld repair, under fully-remote operations, can be extremely costly and time consuming. Current closure welding technology (fusion welding) is not well suited for this application and will present risk to cleanup cost and schedule. To address this risk, Fluor and the Pacific Northwest National Laboratory (PNNL), are proposing that a new and emerging joining technology, Friction Stir Welding (FSW), be considered for this work. FSW technology has been demonstrated in other industries (aerospace and marine) to produce near flaw-free welds on a consistent basis. FSW is judged capable of providing the needed performance for fully-remote closure welding of containers for radioactive materials for the following reasons: FSW is a solid-state process; material is not melted. As such, FSW does not produce the type of defects associated with fusion welding, e.g., solidification-induced porosity, cracking, distortion due to weld shrinkage, and residual stress. In addition, because FSW is a low-heat input process, material properties (mechanical, corrosion and environmental) are preserved and not degraded as can occur with 'high-heat' fusion welding processes. When compared to fusion processes, FSW produces extremely high weld quality. FSW is performed using machine-tool technology. The equipment is simple and robust and well-suited for high radiation, fully-remote operations compared to the relatively complex equipment associated with the fusion-welding processes. Additionally, for standard wall thicknesses of radioactive materials containers, the FSW process can perform final closure welding in a single pass (GTAW requires multiple passes) resulting in increased productivity. Together, the performance characteristics associated with FSW, i.e., high weld quality, simple machine-tool equipment and increased welding efficiency, are expected to reduce risk to upcoming DOE radioactive materials packaging campaigns. FSW technology requires some development/adaptation for this application, along with approval from the governing code of construction prior to production operations. This paper addresses the need for a new joining technology, a description of the FSW process and why it is well-suited for this application, and several activities required for commercialization.

42 ENGINEERING↗

CODE ACCEPTANCE OF A NEW JOINING TECHNOLOGY FOR STORAGE CONTAINMENTS [REISSUE]

One of the activities associated with cleanup throughout the Department of Energy (DOE) complex is packaging radioactive materials into storage containers. Much of this work will be performed in high-radiation environments requiring fully remote operations, for which existing, proven systems do not currently exist. These conditions require a process that is capable of producing acceptable (defect-free) welds on a consistent basis; the need to perform weld repair, under fully-remote operations, can be extremely costly and time consuming. Current closure-welding technologies (fusion welding) are not well suited for this application and will present risk to cleanup cost and schedule. To address this risk, Fluor and the Pacific Northwest National Laboratory (PNNL) are proposing that a new and emerging joining technology, Friction Stir Welding (FSW), be considered for this work. FSW technology has been demonstrated in other industries (aerospace and marine) to produce near flaw-free welds on a consistent basis. FSW is judged capable of providing the needed performance for fully-remote closure welding of containers for radioactive materials for the following reasons: FSW is a solid-state process; material is not melted. FSW does not produce the type of defects associated with fusion welding, e.g., solidification-induced porosity, cracking, and distortion due to weld shrinkage. In addition, because FSW is a low-heat input process, material properties (mechanical, corrosion and environmental) experience less degradation in the heat affected zones than do fusion welds. When compared to fusion processes, FSW produces extremely high weld quality. FSW is performed using machine-tool technology. The equipment is simple and robust and well-suited for high radiation, fully-remote operations compared to the relatively complex equipment associated with fusion-welding processes. Additionally, for standard wall thicknesses of radioactive materials containers, the FSW process can perform the final closure in a single pass (GTAW requires multiple passes) resulting in increased productivity. The performance characteristics of FSW, Le., high weld quality, simple machine-tool equipment and increased welding efficiency, suggest that this new technology should be considered for radioactive materials packaging campaigns. FSW technology will require some development, adaptation for this application, along with several activities needed for commercialization. One of these activities will be to obtain approval from the governing construction code to use the FSW technology. The American Society of Mechanical Engineers Boiler and Pressure Vessel Code (ASME B&PVC) will govern this work; however, rules for the use of FSW are not currently addressed. A code case will be required, defining appropriate process variables within prescribed limits, and submitted to the Code for review/approval and incorporation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Chemical kinetic modeling of component mixtures relevant to gasoline

Real fuels are complex mixtures of thousands of hydrocarbon compounds including linear and branched paraffins, naphthenes, olefins and aromatics. It is generally agreed that their behavior can be effectively reproduced by simpler fuel surrogates containing a limited number of components. In this work, a recently revised version of the kinetic model by the authors is used to analyze the combustion behavior of several components relevant to gasoline surrogate formulation. Particular attention is devoted to linear and branched saturated hydrocarbons (PRF mixtures), olefins (1-hexene) and aromatics (toluene). Model predictions for pure components, binary mixtures and multi-component gasoline surrogates are compared with recent experimental information collected in rapid compression machine, shock tube and jet stirred reactors covering a wide range of conditions pertinent to internal combustion engines. Simulation results are discussed focusing attention on the mixing effects of the fuel components.

02 PETROLEUM↗

Detailed Kinetic Modeling of Gasoline Surrogate Mixtures

Real fuels are complex mixtures of thousands of hydrocarbon compounds including linear and branched paraffins, naphthenes, olefins and aromatics. It is generally agreed that their behavior can be effectively reproduced by simpler fuel surrogates containing a limited number of components. In this work, a recently revised version of the kinetic model by the authors is used to analyze the combustion behavior of several components relevant to gasoline surrogate formulation. Particular attention is devoted to linear and branched saturated hydrocarbons (PRF mixtures), olefins (1-hexene) and aromatics (toluene). Model predictions for pure components, binary mixtures and multi-component gasoline surrogates are compared with recent experimental information collected in rapid compression machine, shock tube and jet stirred reactors covering a wide range of conditions pertinent to internal combustion engines. Simulation results are discussed focusing attention on the mixing effects of the fuel components.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

A High-Throughput Study of PtNiZr Catalysts for Application in PEM Fuel Cells

The effects of adding Zr to PtNi oxygen reduction reaction (ORR) electrocatalyst alloys were examined in a study aimed at probing the possibility of creating catalysts with enhanced resistance to corrosion in a PEM fuel cell environment. Samples consisting of pure Pt or PtNiZr alloys with a range of compositions (not exceeding 11 at.% Zr) were fabricated using co-sputter deposition. A high-throughput fabrication approach was used wherein 18 distinct thin film catalyst alloy samples with varying compositions were deposited onto a large-area substrate with individual Au current collector structures. A multi-channel pseudo-potentiostat allowed for the simultaneous quantitative study of catalytic activity for all 18 electrodes in a single test bath, a first for the study of ORR electrocatalysts. A properly stirred oxygenated 1 M H{sub 2}SO{sub 4} electrolyte solution was used to provide each electrode with a steady-state flow of reactants during electrochemical evaluation. The onset potentials, absolute current density values, and Tafel analysis data obtained using this technique were compared with literature reports. The analyses showed that most PtNiZr alloys tested offered improvements over pure Pt, however those surfaces with a high mole fraction (>4 at.%) of Zr exhibited reduced activity that was roughly inversely correlated to the amount of Zr present. Film composition, morphology, and crystallographic properties were examined using X-ray energy dispersive spectroscopy (XEDS), X-ray photoelectron spectroscopy (XPS), SEM, and synchrotron X-ray diffraction. These data were then correlated with electrochemical data to elucidate the relationships between composition, structure, and relative performance for this ternary system.

30 DIRECT ENERGY CONVERSION↗

The contour method: a new approach in experimental mechanics

The recently developed contour method can measure complex residual-stress maps in situations where other measurement methods cannot. This talk first describes the principle of the contour method. A part is cut in two using a precise and low-stress cutting technique such as electric discharge machining. The contour of the resulting new surface, which will not be flat if residual stresses are relaxed by the cutting, is then measured. Finally, a conceptually simple finite element analysis determines the original residual stresses from the measured contour. Next, this talk gives several examples of applications. The method is validated by comparing with neutron diffraction measurements in an indented steel disk and in a friction stir weld between dissimilar aluminum alloys. Several applications are shown that demonstrate the power of the contour method: large aluminum forgings, railroad rails, and welds. Finally, this talk discusses why the contour method is significant departure from conventional experimental mechanics. Other relaxation method, for example hole-drilling, can only measure a 1-D profile of residual stresses, and yet they require a complicated inverse calculation to determine the stresses from the strain data. The contour method gives a 2-D stress map over a full cross-section, yet a direct calculation is all that is needed to reduce the data. The reason for these advantages lies in a subtle but fundamental departure from conventional experimental mechanics. Applying new technology to old methods like will not give similar advances, but the new approach also introduces new errors.

36 MATERIALS SCIENCE↗

Solidification Tests for LLW Sludges

Oak Ridge National laboratory has about 350,000 gallons of remote-handled (RH) sludge in ten liquid low-level waste (LLLW) tanks that must be solidified and stabilized for disposal at the Nevada Test Site. Samples of the waste sludge were collected from four tanks, and a total of 36 small-scale grouting tests were performed. The presence of free water during curing was evaluated, and the cured grouts were analyzed using the Toxicity Characteristic Leaching Procedure (TCLP) to determine if any of the hazardous metals in the sludge (Cd, Cr, Hg, Pb, etc.) would leach above the Resource Conservation and Recovery Act (RCRA) limits/ The grouting formulation used for these tests, with ratios of grout-forming additives weight to waste slurry weight ranging from 0.75:1 to 1.2:1, produced wet grout mixtures that were easy to stir and were self leveling. The grout mixtures cured with no free water visible at any time. The cured grout matrix was very effective at retaining the hazardous metals in the sludge, with TCLP leachate concentrations well below the RCRA limits. The addition of ferrous sulfide (FeS) to some of the sludge samples resulted in, at most, a minimal reduction in the amount of mercury that leached from the grout samples, and had no detectable impact on the other heavy metals present in the sludge (Cd, Cr, and Pb). The TCLP extraction was performed on three samples after 1 day and 7 days of curing, compared to the >28 days for the remaining samples. The metal concentrations for the short cure time samples were similar to the remaining samples, and were all well below the RCRA limits.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Surface engineered nanoparticles for improved surface enhanced Raman scattering applications and method for preparing same

A method for producing metal nanoparticles that when associated with an analyte material will generate an amplified SERS spectrum when the analyte material is illuminated by a light source and a spectrum is recorded. The method for preparing the metal nanoparticles comprises the steps of (i) forming a water-in-oil microemulsion comprising a bulk oil phase, a dilute water phase, and one or more surfactants, wherein the water phase comprises a transition metal ion; (ii) adding an aqueous solution comprising a mild reducing agent to the water-in-oil microemulsion; (iii) stirring the water-in-oil microemulsion and aqueous solution to initiate a reduction reaction resulting in the formation of a fine precipitate dispersed in the water-in-oil microemulsion; and (iv) separating the precipitate from the water-in-oil microemulsion.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Detailed chemical kinetic mechanism for the oxidation of biodiesel fuels blend surrogate.

Detailed chemical kinetic mechanisms were developed and used to study the oxidation of two large unsaturated esters: methyl-5-decenoate and methyl-9-decenoate. These models were built from a previous methyl decanoate mechanism and were compared with rapeseed oil methyl esters oxidation experiments in a jet stirred reactor. A comparative study of the reactivity of these three oxygenated compounds was performed and the differences in the distribution of the products of the reaction were highlighted showing the influence of the presence and the position of a double bond in the chain. Blend surrogates, containing methyl decanoate, methyl-5-decenoate, methyl-9-decenoate and n-alkanes, were tested against rapeseed oil methyl esters and methyl palmitate/n-decane experiments. These surrogate models are realistic kinetic tools allowing the study of the combustion of biodiesel fuels in diesel and homogeneous charge compression ignition engines.

30 DIRECT ENERGY CONVERSION↗

Probing O 2 -dependence of cyclopentyl reactions via isomer-resolved speciation

Modeling chemical kinetics relevant to low-temperature combustion requires complete description of reactions involving critical species such as hydroperoxyalkyl radicals, Q̇OOH, which undergo competing unimolecular reactions and bimolecular reactions with O 2 . The balance of flux across the two pathways affects rates of chain-branching and depends on temperature, pressure, and oxygen concentration. Accordingly, the influence of [O 2 ] on product formation from alkyl + O 2 reactions and the subsequent fate of Q̇OOH and related products is central to the development of an accurate chemical kinetics mechanism. Furthermore, chemical reactions consuming Q̇OOH-mediated species are often simplified to such a degree that mechanism truncation error (uncertainty derived from incomplete reaction networks) becomes significant.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Biofuel Combustion Chemistry: From Ethanol to Biodiesel

Biofuels, such as bio‐ethanol, bio‐butanol, and biodiesel, are of increasing interest as alternatives to petroleum‐based transportation fuels because they offer the long‐term promise of fuel‐source regenerability and reduced climatic impact. Current discussions emphasize the processes to make such alternative fuels and fuel additives, the compatibility of these substances with current fuel‐delivery infrastructure and engine performance, and the competition between biofuel and food production. However, the combustion chemistry of the compounds that constitute typical biofuels, including alcohols, ethers, and esters, has not received similar public attention. Herein we highlight some characteristic aspects of the chemical pathways in the combustion of prototypical representatives of potential biofuels. The discussion focuses on the decomposition and oxidation mechanisms and the formation of undesired, harmful, or toxic emissions, with an emphasis on transportation fuels. New insights into the vastly diverse and complex chemical reaction networks of biofuel combustion are enabled by recent experimental investigations and complementary combustion modeling. Understanding key elements of this chemistry is an important step towards the intelligent selection of next‐generation alternative fuels.

02 PETROLEUM↗

Magnesium Alloy ZK60 Tubing made by Shear Assisted Processing and Extrusion (ShAPE)

ZK60 Magnesium tubing has been friction extruded from as-cast billets and T5 conditioned bars using Shear Assisted Processing and Extrusion (ShAPE). Tubes having an outer diameter of 50.8 mm and wall thickness of 1.9 mm were extruded with >20 times less ram force compared to conventional extrusion due to the unique shearing conditions and tooling inherent to ShAPE. Microstructures of the as-cast billet and T5 bar feedstock materials were significantly different from each other in terms of grain size, texture, and second phase distribution; yet the resulting microstructures after ShAPE were remarkably similar. An average grain size of 4-5 microns, 20o tilt of basal texture away from the extrusion axis, and refined second phases having a uniform distribution were achieved independent of the feedstock material. Hardness for as-extruded and artificially aged tubes are presented with isotropic behavior explained by detailed microstructural analysis. This work suggests that bulk ZK60 magnesium alloys extrusions may be fabricated in a single step, with microstructures that are unobtainable with conventional extrusion.

Friction Stir Extrusion, Friction Consolidation an↗

Refine your search to explore more results.