Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROLLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

Electron backscatter and X-ray diffraction studies on the deformation and annealing textures of austenitic stainless steel 310S

We studied the texture evolution of thermo-mechanically processed austenitic stainless steel 310S. This alloy was cold rolled up to 90% reduction in thickness and subsequently annealed at 1050 °C. At the early stages of deformation, strain-induced martensite was formed from deformed austenite. By increasing the deformation level, slip mechanism was found to be insufficient to accommodate higher deformation strains. Our results demonstrated that twinning is the dominant deformation mechanism at higher deformation levels. Results also showed that cold rolling in unidirectional and cross rolling modes results in Goss/Brass and Brass dominant textures in deformed samples, respectively. Similar texture components are observed after annealing. Thus, the annealing texture was greatly affected by texture of the deformed parent phase and martensite did not contribute as it showed an athermal reversion during annealing. Results also showed that when the fraction of martensite exceeds a critical point, its grain boundaries impeded the movement of austenite grain boundaries during annealing. As a result, recrystallization incubation time would increase. This caused an incomplete recrystallization of highly deformed samples, which led to a rational drop in the intensity of the texture components. - Highlights: •Thermo-mechanical processing through different cold rolling modes can induce different textures. •Martensite reversion is athermal during annealing. •Higher fraction of deformation-induced martensite can increase the annealing time required for complete recrystallization. •Annealing texture is mainly influenced by the deformation texture of austenite.

36 MATERIALS SCIENCE↗

Elucidating the microscopic origin of electrochemical corrosion and electrical conductivity by lattice response to severe plastic deformation in Al-Mn-Si alloy

Highlights: • Al-Mn-Si specimens were underwent severe plastic deformation by CGP and cold-rolling and their combined routes. • Microscopical observations depicted particles' fragmentation and non-preferential distribution under heavy straining. • XRD analysis revealed dislocations annihilation and lattice swelling (d-spacing increase) due to dynamic recrystallization. • Polarization outputs disclosed direct correlation of corrosion behavior with dislocations density. • Four-point probe test proved that electrical conductivity was a function of lattice d-spacing. - Abstract: Al-Mn-Si specimens were underwent SPD by CGP, cold-rolling and their combined paths. Acquired OM and SEM micrographs revealed that random distribution of intermetallic precipitates beside their fragmentation under heavy imposed strains deteriorated particles’ influence on the electrochemical corrosion and inhibited pitting. Analysis of XRD patterns pointed out that post-rolling of CGPed sheets resulted in dynamic annihilation of dislocations and accordingly crystal lattice swelling (d-spacing increase) due to dynamic recrystallization. From polarization results, crystallites’ refinement along with density increment of sub-grain boundaries within structure as a consequence of SPD beside dislocation density enhancement accelerated corrosion. Outputs of four-point probe electrical conductivity examination indicated that apart from the employed processing, lattice compaction and atomic layers approach would limit the electrons’ mobility space and hence reduce the conductivity of material. In this regard, combined effects of CGP and rolling as employed dual-straining route on Al-Mn-Si alloy enhanced the electrical conductivity by d-spacing growth.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

FEM Analysis of Defects and Microstructure Evolution during Hot Working of Specialty Alloys

The main goals of process simulation in manufacturing are to reduce manufacturing/part development time and cost as well as increasing quality and productivity. In this study, porosity evolution is modeled by introducing a porosity evolution parameter, which is function of strain rate and stress triaxiality factor. Applicability is shown by simulating the first two stages of an ingot conversion process; variables are die geometry and bite size. Moreover, application is extended to hot shape rolling, where the geometry of the oval passes is the variable. Validation is carried out through evaluation of samples from final products. Also, surface defects in hot shape rolling are tracked by studying the instability during the rolling of the material. Plastic work approach was used to judge the occurrence of instability during the process. The effect of number of passes and roll gap was examined to predict the occurrence of surface cracking. On the other hand, unrecrystallized grains and coarse grain problem are other significant problems in the metalworking industry. A recrystallization model is implemented in a finite element framework, to study the effect of forging parameters on the microstructure evolution during ingot conversion process of a superalloy.

36 MATERIALS SCIENCE↗

The influence of time dependent flight and maneuver velocities and elastic or viscoelastic flexibilities on aerodynamic and stability derivatives

The advent of new structural concepts employing composites in primary load carrying aerospace structures in UAVs, MAVs, Boeing 787s, Airbus A380s, etc., necessitates the inclusion of flexibility as well as viscoelasticity in static structural and aero-viscoelastic analyses. Differences and similarities between aeroelasticity and aero-viscoelasticity have been investigated in [2]. An investigation is undertaken as to the dependence and sensitivity of aerodynamic and stability derivatives to elastic and viscoelastic structural flexibility and as to time dependent flight and maneuver velocities. Longitudinal, lateral and directional stabilities are investigated. It has been a well established fact that elastic lifting surfaces are subject to loss of control effectiveness and control reversal at certain flight speeds, which depend on aerodynamic, structural and material properties [5]. Such elastic analyses are extended to linear viscoelastic materials under quasi-static, dynamic, and sudden and gradual loading conditions. In elastic wings one of the critical static parameters is the velocity at which control reversal takes place (V{sub REV}{sup E}). Since elastic formulations constitute viscoelastic initial conditions, viscoelastic reversal may occur at speeds V{sub REV<}{sup ≧}V{sub REV}{sup E}, but furthermore does so in time at 0 < t{sub REV} ≤ ∞. The influence of the twin effects of viscoelastic and elastic materials and of variable flight velocities on longitudinal, lateral, directional and spin stabilities are also investigated. It has been a well established fact that elastic lifting surfaces are subject to loss of control effectiveness and control reversal at certain flight speeds, which depend on aerodynamic, structural and material properties [5]. Such elastic analyses are here extended to linear viscoelastic materials under quasi-static, dynamic, and sudden and gradual loading conditions. In elastic wings the critical parameter is the velocity at which control reversal takes place (V{sub REV}{sup E}). Since elastic formulations constitute viscoelastic initial conditions, viscoelastic reversal may occur at speeds V{sub REV<}{sup ≧}V{sub REV}{sup E}, but furthermore does so in time at 0 < t{sub REV} ≤ ∞. This paper reports on analytical analyses and simulations of the effects of flexibility and time dependent material properties (viscoelasticity) on aerodynamic derivatives and on lateral, longitudinal, directional and spin stability derivatives. Cases of both constant and variable flight and maneuver velocities are considered. Analytical results for maneuvers involving constant and time dependent rolling velocities are analyzed, discussed and evaluated. The relationships between rolling velocity p and aileron angular displacement β as well as control effectiveness are analyzed and discussed in detail for elastic and viscoelastic wings. Such analyses establish the roll effectiveness derivatives (∂[p(t)])/(V{sub ∞}∂β(t)) . Similar studies involving other stability and aerodynamic derivatives are also undertaken. The influence of the twin effects of viscoelastic and elastic materials and of variable flight, rolling, pitching and yawing velocities on longitudinal, lateral and directional are also investigated. Variable flight velocities, encountered during maneuvers, render the usually linear problem at constant velocities into a nonlinear one.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

LANL technical progress update for US HJPRR working group

The outline of this presentation is: (1) Collaboration on Master Alloy Melting; (2) Data for Safety Analysis, (3) HIP can development status, (4) Bond strength quality, (5) Plasma spraying results, and (6) Bare Rolling Larger Rolling Ingots. Significant near term progress has been made in five areas: (1) Collaboration on Master Alloy Melting; (2) HIP can development status; (3) Bond strength quality; (4) Plasma spraying results; and (5) Bare Rolling Larger Rolling Ingots. Significant progress is expected in the next month on several important areas: (1) Intrinsic bond strength of plasma sprayed Zr (2) Advanced Cleaning; (3) Residual Stress Collaboration with INL; and (4) Cost Metric Assessment.

36 MATERIALS SCIENCE↗

Designing Low Tortuosity Electrodes through Pattern Optimization for Fast-Charging

The development of fast-charging technologies is crucial for expediting the progress and promotion of electric vehicles. In addition to innovative material exploration, reduction in the tortuosity of electrodes is a favored strategy to enhance the fast-charging capability of lithium-ion batteries by optimizing the ion-transfer kinetics. To realize the industrialization of low-tortuosity electrodes, a facile, cost-effective, highly controlled, and high-output continuous additive manufacturing roll-to-roll screen printing technology is proposed to render customized vertical channels within electrodes. Extremely precise vertical channels are fabricated by applying the as-developed inks, using LiNi 0.6 Mn 0.2 Co 0.2 O 2 as the cathode material. Additionally, the relationship between the electrochemical properties and architecture of the channels, including the pattern, channel diameter, and edge distance between channels, is revealed. The optimized screen-printed electrode exhibited a seven-fold higher charge capacity (72 mAh g -1 ) at a current rate of 6 C and superior stability compared with that of the conventional bar-coated electrode (10 mAh g -1 , 6 C) at a mass loading of 10 mg cm -2 . Finally, this roll-to-roll additive manufacturing can potentially be applied to various active materials printing to reduce electrode tortuosity and enable fast charging in battery manufacturing.

42 ENGINEERING↗

Modeling Arctic boundary layer cloud streets at grey-zone resolutions

To better understand how model resolution affects the formation of Arctic boundary layer clouds, we investigated the influence of grid spacing on simulating cloud streets that occurred near Utqiagvik (formerly Barrow), Alaska on 2 May 2013 and were observed by the Moderate Resolution Imaging Spectroradiometer (MODIS). The Weather Research and Forecasting model was used to simulate the clouds using nested domains with increasingly fine resolution ranging from a horizontal grid spacing of 27 km in the boundary-layer-parameterized mesoscale domain to a grid spacing of 0.111 km in the large-eddy-permitting domain. We investigated the model-simulated mesoscale environment, horizontal and vertical cloud structures, boundary layer stability, and cloud properties, all of which were subsequently used to interpret the observed roll-cloud case. Increasing model resolution led to a transition from a more buoyant boundary layer to a more shear-driven turbulent boundary layer. The clouds were stratiform-like in the mesoscale domain, but as the model resolution increased, roll-like structures, aligned along the wind field, appeared with ever smaller wavelengths. A stronger vertical water vapor gradient occurred above the cloud layers with decreasing grid spacing. With fixed model grid spacing at 0.333 km, changing the model configuration from a boundary layer parameterization to a large-eddy-permitting scheme produced a more shear-driven and less unstable environment, a stronger vertical water vapor gradient below the cloud layers, and the wavelengths of the rolls decreased slightly. In this study, only the large-eddy-permitting simulation with gird spacing of 0.111 km was sufficient to model the observed roll clouds.

Lai, Hui-Wen↗

Investigation of main bearing operating conditions in a three-Point mount wind turbine drivetrain

Wear-related failures of spherical roller bearings in the main bearing position of three-point mount wind turbines have been higher than expected and can contribute to higher than anticipated operation-and-maintenance costs. In this paper, the operational conditions of such a main bearing—including measured axial displacement and velocity subject to the estimated axial loads—are described for an instrumented, commercial wind turbine. The field measurements suggest a maximum axial speed between the bearing rings that is less than 2 millimeters per second. It is estimated that the axial speed between the ring and rollers is approximately 25% of this value. When compared to a speed of rolling from approximately 200–352 millimeters per second, the measured axial sliding is therefore significantly less than 1% of the speed of rolling. Previous numerical studies of lubricant film formation in rolling contacts have shown that the effect of axial sliding starts to be noticeable only when this ratio exceeds 10%; therefore, the axial velocity represents only a small disturbance to the nominal pure rolling case, and the influence on oil film building can be neglected. A simple analytic model of the main bearing motion was also developed and demonstrated similar displacement and velocity characteristics.

17 WIND ENERGY↗

Effect of the Processing-Induced Morphology on the Mechanical Properties of Biodegradable Extruded Films Based on Poly(lactic acid) (PLA) Blends

Biodegradable films based on poly(lactic acid) blends were obtained by cast extrusion. Their tensile and fracture behavior was investigated and the effect of the processing conditions through the extrusion rolling speed on this behavior was analyzed. In uniaxial tensile tests, all films presented completely ductile behavior exhibiting a defined yield point, strain softening after this point and a plateau before fracture. Fracture behavior was determined through quasi-static fracture tests on deeply double edge notched tensile specimens. The film obtained at the lowest rolling speed exhibited completely ductile behavior hence, the Essential Work of Fracture methodology was applied to characterize its fracture. The film processed at intermediate rolling speed, on the other hand, presented ductile fracture or ductile instability depending on the ligament length and the film obtained with the highest rolling speed exhibited a transition regime fracture. In order to compare the fracture behavior of the different films, the J-integral at maximum load J{sub max} was adopted. Differences in the films fracture behavior were correlated to the processing-induced morphology.

36 MATERIALS SCIENCE↗

Studies on Bio-acceptability of Thermo-Mechanically Processed Mg-4Li-0.5Ca Alloy and Its Microstructural Correlation

In this study, in vitro corrosion behavior of rolled Mg-4Li-0.5Ca (wt.%) alloy at three temperatures (250, 300 and 350 °C) with 75% reduction and subsequent short annealing at 200 °C for 10 min was systematically investigated. Microstructural evaluation, Mg{sub 2}Ca precipitation and defects like twins were characterized by an optical microscope, scanning electron microscope and x-ray diffraction. Micrographs reveal an increase in grain size and comparatively reduction in twins density population with an increase in hot rolling temperature and subsequent short annealing. In vitro corrosion tests like dynamic bio-corrosion immersion test, hydrogen evolution test and electrochemical linear polarization test were carried out in simulated body fluid. From in vitro corrosion tests, it is observed that the alloy rolled at 350 °C and subsequently short-annealed shows better bio-corrosion resistance than other hot-rolled and short-annealed alloys. This is due to low twins density and uniformly dispersed Mg{sub 2}Ca compound throughout the matrix.

36 MATERIALS SCIENCE↗

Mechanically and thermally robust microporous copolymer separators for lithium ion batteries

Next generation, multifunctional separators can enhance energy storage, power, and safety performance of lithium ion batteries but must be simple to fabricate and incorporate with existing roll-to-roll manufacturing. Here, this study presents a strategy to facilely prepare these separators using UV-initiated polymerization-induced phase separation (PIPS), wherein microporous polymer separators are fabricated directly from constituent monomers and ethylene carbonate (EC) porogen. This enables a wide compositional design space as co-monomers with specific chemical functionality can be readily incorporated into the PIPS precursor mixture. Herein, 1,4-butanediol diacrylate (BDDA) was copolymerized with poly(ethylene glycol) diacrylate (PEGDA) to increase the acrylate conversion in the photopolymerization and improve mechanical properties. By tuning the ratio of PEGDA and EC, separators with high porosity (41.3%) and effective ionic conductivity (2.09 mS cm –1 ) were prepared. Inclusion of PEGDA was essential to increasing the elastic modulus to > 345 MPa, which is required for cell assembly by roll-to-roll manufacturing. All separators prepared were shown to enable reversible cycling of lithium metal/LiNi 0.5 Mn 0.3 Co 0.2 O 2 half-cells for 100 cycles. Unlike conventional polyolefin separators, which were shown to melt at 160 °C and shrink by up to 29.8% at elevated temperatures, the PIPS separators possess exceptional, safety-enhancing thermomechanical properties, undergoing no phase transitions or thermal shrinkage.

25 ENERGY STORAGE↗

Characterization of surface layers formed on DU10Mo ingots after processing steps and high humidity exposure

The design of monolithic U-Mo fuel elements fabricated from low-enriched uranium for use in high-power research reactors requires bonding of the fuel foil to either Al cladding or a Zr barrier layer. Processing of the U-Mo ingot to final foil form has the potential to generate surface layers on the foil that differ from the bulk, metallic U-Mo. The interfacial properties between the U-Mo and Zr or Al cladding layers will then be determined by these surface layers. We use x-ray photoelectron spectroscopy, cross-sectional scanning electron microscopy, and atomic force microscopy to characterize the composition, oxidation state, and morphology of the surface layers that form after hot rolling and cold rolling depleted U–10 wt% Mo alloy (DU10Mo). A thick uranium nitride layer is observed after hot rolling, although its origin is likely from a previous processing step. The surface composition of cold-rolled DU10Mo varied significantly between two foils, with a strongly Mo-depleted surface oxide layer observed on one foil but nominal Mo composition observed on the other. The efficacy of acid etching in HNO 3 is compared to that of electropolishing in H 2 SO 4 to remove the surface layers, and both methods are found to be similarly effective. Both laboratory (low humidity) air exposure and longer rinse times in water are shown to promote the formation of surface oxide layers. Exposure of both acid-etched and electropolished DU10Mo foils to humid air (97% relative humidity) for six weeks results in formation of a thick oxide layer due to corrosion. The oxide layer on the acid-etched foil is thicker and more highly oxidized than the oxide layer that forms on the electropolished foil, and these differences in oxidation behavior are attributed to higher surface roughness on the acid-etched foil. In general, Mo is found to play a role as a sacrificial element, typically exhibiting a larger ratio of Mo 6+ / Mo 4+ than U 6+ / U 4+ . This is unexpected, given the greater thermodynamic driving force to form U oxides than Mo oxides.

Kaspar, Tiffany C. (ORCID:0000000328167569)↗

Microstructure evolution and properties of graphene nanoplatelets reinforced aluminum matrix composites

Highlights: • Lamellar structure of GNPs fibers and Al matrix was obtained in the rolling direction. • Stacking faults were observed in Al grains due to greatly increased GNPs/Al interfaces. • Strength of Al-0.2 wt% GNPs increased 36.8% with negligible electrical conductivity loss. - Abstract: Aluminum matrix composites reinforced with graphene nanoplatelets (GNPs) were prepared by continuous casting and subsequent rolling. Al-GNPs master alloy, prepared by ball milling and cold pressing, was added into Al melts to fabricate the composites. Microstructure evolution of the composites were observed using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electron back scattered diffraction (EBSD). GNPs distributed uniformly in the as-cast specimen and then transformed into fibers in the rolling direction after deformation and finally a lamellar structure formed in the composites. Raman spectra showed that the structural damage of GNPs mainly came from ball milling. The interface between GNPs and Al was well combined in general while a few microcracks were observed, which reduced the ductility of the composites and no adverse aluminum carbide (Al{sub 4}C{sub 3}) was detected at the interface. Stacking faults were observed interior of the aluminum grain, which may due to the existence of plentiful interface introduced by GNPs. Fracture observation revealed that the load transferred from Al matrix to GNPs. The ultimate tensile strength of Al-0.2 wt% GNPs composites was about 36.8% higher than that of pure Al with the same casting and rolling process, which should result from the lamellar structure and load transfer, while the conductivity of the composites decreased slightly, indicating that interface scattering between Al and GNPs is very limited. The investigation results show that Al-GNPs composite is potential for high strength and high conductivity application.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

A comparative study of the transformation kinetics of recrystallization texture of CC and DC 3003 aluminum alloys

Highlights: • Recrystallization texture evolution in CC and DC 3003 aluminum alloys was investigated. • A huge difference in recrystallization texture exists between CC and DC AA 3003 alloys. • Concurrent precipitation enhanced the recrystallization activation energy of CC AA 3003 alloy. - Abstract: The evolution of recrystallization texture in cold-rolled CC and DC AA 3003 aluminum alloys was investigated by X-ray diffraction. The results show that a significant difference in recrystallization texture exists between the CC and DC AA 3003 alloys due to the effect of concurrent precipitation. For the CC AA 3003 alloy, low-temperature annealing of cold-rolled sheets results in very strong M and P recrystallization textures. The strength of the M and P recrystallization textures decrease significantly with increasing annealing temperature. For the DC AA 3003 alloy, the recrystallization texture consists of a major cube component and two minor R and Goss components after annealing at low temperatures. The cube, R and Goss recrystallization textures weaken with increasing annealing temperature. The transformation kinetics of recrystallization texture during isothermal annealing can be well described by the JMAK equation. For the CC AA 3003 alloy the n value decreases from about 2.9 to about 0.8 as the annealing temperature increases from 371 °C to 427 °C, while the n value is around 1.5 for the DC AA 3003 alloy. The apparent activation energy for recrystallization of the cold-rolled CC AA 3003 alloy is significantly higher than that of the cold-rolled DC AA 3003 alloy.

36 MATERIALS SCIENCE↗

IPL-Annealed Mixed-Cation Perovskites with Robust Coating Window toward Scalable Manufacturing of Commercial Perovskite Solar Cells

Perovskite solar cells (PSCs) are a promising alternative solar technology, but the technical challenges of (1) stability/durability, (2) efficiency at scale, and (3) manufacturability must be overcome to achieve widespread PSC commercialization. The challenge of balancing solution ink formulation and scalable manufacturing is often overlooked in the literature, where focus is on adopting inks from processes that will not scale. In this study, we apply a classical roll-to-roll manufacturing perspective, utilizing both compositional engineering and intense pulsed light (IPL) annealing, to develop a mixed-cation perovskite ink with a robust coating window that simultaneously solve issues of stability and manufacturability for PSCs. Our method resulted in blade-coated, flexible, mixed-cation PSCs on ITO-PET substrates with a champion power conversion efficiency (PCE) efficiency of 16.7% using IPL annealing of the absorber layer and, to our knowledge, is one of the fastest processing methods for the perovskite layer. This overall reduction in processing time with a stable ink represents an advance toward the scaled production of perovskite solar cells on flexible substrates.

flexible perovskite solar cells↗

Efficient Thick-Film Polymer Solar Cells with Enhanced Fill Factors via Increased Fullerene Loading

Developing effective methods to make efficient bulk-heterojunction polymer solar cells at roll-to-roll relevant active layer thickness is of significant importance. We investigate the effect of fullerene content in polymer:fullerene blends on the fill factor (FF) and on the performance of thick-film solar cells for four different donor polymers PTB7-Th, PDPP-TPT, BDT-FBT-2T, and poly[5,5'-bis(2-butyloctyl)-(2,2'-bithiophene)-4,4'-dicarboxylate-alt-5,5'-2,2'-bithiophene] (PDCBT). At a few hundreds of nanometers thickness, increased FFs are observed in all cases and improved overall device performances are obtained except for PDCBT upon increasing fullerene content in blend films. This fullerene content effect was studied in more detail by electrical and morphological characterization. The results suggest enhanced electron mobility and suppressed bimolecular recombination upon increasing fullerene content in thick polymer:fullerene blend films, which are the result of larger fullerene aggregates and improved interconnectivity of the fullerene phases that provide continuous percolating pathways for electron transport in thick films. These findings are important because an effective and straightforward method that enables fabricating efficient thick-film polymer solar cells is desirable for large-scale manufacturing via roll-to-roll processing and for multijunction devices.

14 SOLAR ENERGY↗

Cloud Morphology Evolution in Arctic Cold‐Air Outbreak: Two Cases During COMBLE Period

Abstract Cloud feedbacks play an important role in Arctic warming. Cloud morphology, for example, cloud size and spatial distributions, is among key factors that directly impact their radiative effects. In this work, we use two cases observed during the Cold‐air Outbreak (CAO) in the Marine Boundary Layer Experiment (COMBLE) to study the evolution of cloud size distributions as an air mass is advected from the Arctic over a comparatively warm ocean and cloud mesoscale organization changes from rolls to cells. Cloud objects are identified from Moderate Resolution Imaging Spectroradiometer (MODIS) reflectance images through an object segmentation procedure and roll breakup is identified by homogeneities in cloud water path (CWP). Roll breakup is found to be accompanied by a local minimum in wind shear and local maxima in cloud size and marine cold air outbreak index. The mean cloud horizontal aspect ratio has weak fetch dependency and is around 2 in roll, transition, and cell regimes. Regardless of distance from the ice edge, smaller clouds (<10 km 2 ) dominate the population number but not cloud cover. Cloud size distributions show bimodality in transition and cell regimes. For clouds with comparable sizes, mean nearest neighbor distances normalized by equivalent cloud radius converge to a single value for all regimes and for all but the smallest clouds, suggesting that clouds of comparable sizes in CAOs are separated by distance proportional to their sizes. The presented statistical results pave the way to evaluating model simulated cloud organizations during CAO events.

54 ENVIRONMENTAL SCIENCES↗

Refine your search to explore more results.