Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLASMA COMPOSITION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

Material property for designing, analyzing, and fabricating space structures

An analytical study was made of plasma assisted bullet projectile. The finite element analysis and the micro-macromechanic analysis was applied to an optimum design technique for the multilayered graphite-epoxy composite projectile that will achieve hypervelocity of 6 to 10 Km/s. The feasibility was determined of dialectics to monitor cure of graphite-epoxies. Several panels were fabricated, cured, and tested with encouraging results of monitoring the cure of graphite-epoxies. The optimum cure process for large structures was determined. Different orientation were used and three different curing cycles were employed. A uniaxial tensile test was performed on all specimens. The optimum orientation with the optimum cure cycle were concluded.

Kolkailah, Faysal A.↗

X-ray Photoelectron Spectroscopy Study of Argon-Plasma-Treated Fluoropolymers

Films of poly(tetrafluoroethylene) (PTFE) and of a tetrafluoroethylene-perfluoroalkyl vinyl ether (approximately 49:1) copolymer (PFA) were exposed to a radio-frequency argon plasma and then examined by X-ray photoelectron spectroscopy (XPS). The use of fluoropolymer films nearly free of surface hydrocarbon contamination as well as the use of a monochromatized X-ray source for XPS removed two factors contributing to conflicting reports on the effect of exposure time on the fluorine-to-carbon (F/C) and oxygen-to-carbon (O/C) ratios for several Ar-plasma-treated fluoropolymers. Contrary to literature indications, a common pattern was found for PTFE and PFA: a moderate decrease in F/C ratio (from 1.99 to 1.40, and from 1.97 to 1.57, respectively), together with a moderate increase in O/C ratio (from negligible to about 0.10, and from 0.012 to about O.10, respectively) at very short exposures, after which the F/C ratios remained essentially constant on prolonged exposures, while the O/C ratios for PTFE and PFA leveled off at 0.11 and 0.15, respectively. The XPS C(sub 1s), spectra for these polymers exposed to the Ar plasma for 20 min were similar and presented, besides a prominent peak at 292.0 eV (CF2,) and a minor peak at 294.0 or 294.1 eV (CF3), a composite band of four curve-resolved peaks (approximately 285-290 eV) representing various CH, CC, CO, CN, and CF functionalities.

Golub, Morton A.↗

Near-Earth Interplanetary Coronal Mass Ejections During Solar Cycle 23 (1996 - 2009): Catalog and Summary of Properties

In a previous study (Cane and Richardson, J. Geophys. Res. l08(A4), SSH6-1, we investigated the occurrence of interplanetary coronal mass ejections in the near-Earth solar wind during 1996 - 2002, corresponding to the increasing and maximum phases of solar cycle 23, and provided a "comprehensive" catalog of these events. In this paper, we present a revised and updated catalog of the approx. =300 near-Earth ICMEs in 1996-2009, encompassing the complete cycle 23, and summarize their basic properties and geomagnetic effects. In particular, solar wind .. composition and charge state observations are now considered when identifying the ICMEs. In general, these additional data confirm the earlier identifications based predominantly on other solar wind plasma and magnetic field parameters. However, the boundaries of ICME-like plasma based on charge state/composition data may deviate significantly from those based on conventional plasma/magnetic field parameters. Furthermore, the much studied "magnetic clouds", with flux-rope-like magnetic field configurations, may form just a substructure of the total ICME interval.

Richardson, I. G.↗

Characterization of compositional variation and solidification condition on rapid solidification behavior of beta stabilized titanium

Rapid solidification (RS) is a field of study that has increased in importance due to the rise of additive manufacturing (AM) techniques. The breakdown of equilibrium at the solid-liquid interface results in an inability to use traditional solidification models that have been applied to great success in casting. As such, there is a current need for a high-throughput testing method to screen alloys at rapid solidification conditions without the significant cost for powder atomization. In this work, twin hammer splat quenching (SQ) is utilized and theoretically developed as a technique uniquely placed to test alloy systems for AM applications. Using analytical thermal spray models and numerical heat transfer simulations, the cooling rate and solidification conditions of splat quenching are compared across several parameters to evaluate the key parameters for generating cooling rates relevant to AM process. Once a framework for the cooling rates and relevancy of SQ are developed, SQ was used to process alloy compositions in the Ti5553 alloy space (AMS 7026) to study the formation of detrimental secondary phases occurring upon rapid quenching from the melt. A martensitic phase is found to occur at the lower end of the standard, but the composition listed in the standard were found to be safe. Finally, the rapid solidification behavior of Ti-5553 is evaluated by comparing splat quenching, laser welding, and plasma atomization that offer a wide window of solidification conditions. The segregation and solidification structure are analyzed and compared to models to provide a deeper understanding of the solidification behavior of beta stabilized titanium alloys.

Williamson, Christopher J.↗

ITER Neutronic Challenges for Upper Port 14

The future of magnetically confined nuclear fusion facilities is extremely promising, yet there are extensive challenges that still have to be addressed. These challenges range significantly, but one of the more difficult challenges is nuclear shielding and nuclear safety. The challenge of adequately shielding neutrons is especially prevalent at ITER. Throughout the lifetime of ITER there will be large quantities of high energy (14.1- MeV) neutrons generated, with the expected neutron lifetime fluence to be around 0.3 MW.a/m{sup 2}. For such a large neutron fluence, shielding is a very important factor for the operation of ITER. Not only the shielding of the people that will be supporting the facility, but also to the components that surround the plasma. Without the many diagnostics that are planned for ITER operation, ITER would not be able to function. But with the inclusion of the diagnostics and the many apertures required, an interesting neutronics environment is created. This environment is like nothing we have seen or are currently able to create on the earth. Due to this unknown, significant time and effort is being placed on the research, design, and analysis of the ITER neutronics environment. A neutron has an interesting life after birth within the plasma on ITER. There are many different paths and reactions that can take place; so many, that trying to simplify the problem has brought significant unknowns into the analysis. Due to unique material compositions, neutron streaming paths, and neutronics requirements, the simplest of ITER neutronics calculations have to be thought out in great detail. Placing a new hole for a diagnostic creates a new streaming path; internal components must survive a high fast neutron flux, while external components face a completely different neutron energy spectrum of a high flux; material activation within human accessible areas must be maintained to an allowable level. As the complexity of the ITER device grows, so does the complexity of the neutronics challenges.

61 RADIATION PROTECTION AND DOSIMETRY↗

The Significance of Helium in the Solar Wind: Insights from 1 AU

Doubly ionized helium is the 2nd most abundant element in the solar wind. The solar wind’s properties are a function of the source region on the Sun from which it emanates. This includesthe abundances of solar wind Helium and rarer, heavier elements. The speed of the solar wind, when observed near Earth, is also related to the type of source region from which the solar wind originated. Early solar wind models are unable to explain how the solar wind achieved the asymptotically fastest, non-transient speeds observed at 1 AU and the solar wind must be accelerated during transit through interplanetary space. Only recently have observations shown that the solar wind from different source regions is accelerated by different mechanisms. However, the solar wind speed is also known to be an insufficient for identifying the type of solar source from which it originated, likely because these different acceleration mechanisms accelerate the solar wind into two different speed regimes that overlap. Furthermore, the mechanism that provides the coronal plasma sufficient energy to accelerate into the solar wind is still undetermined. These mysteries are further complicated by the Sun’s evolution through its 11-year activity cycle and the impact of the solar cycle on in situ observations. Using solar wind observations of the helium abundance from the Wind spacecraft and heavy ion abundances from the Advanced Composition Explorer (ACE) along with observations of the Sunspot Number – a long-studied proxy for the Sun’s activity – we will discuss the imprint of different solar wind source regions on observations collected at 1 AU. We will draw inferences about the role of helium in the acceleration of coronal plasma into the solar wind. Using the Alfvénicity – a metric related to the solar wind acceleration that occurs during transit through interplanetary space – we will derive a solar wind classification scheme for near-Earth observations that is related to the differences in the source regions from which it emanates.

Benjamin Alterman↗

ELECTRON-ION SCATTERING IN DENSE MULTI-COMPONENT PLASMAS: APPLICATION TO THE OUTER CRUST OF AN ACCRETING NEUTRON STAR

The thermal conductivity of a dense multi-component plasma (MCP) is critical to the modeling of accreting neutron stars. To this end, we perform large-scale molecular dynamics simulations to calculate the static structure factor of the dense MCP in the neutron star crust from near the photosphere-ocean boundary to the vicinity of the neutron drip point. The structure factors are used to validate a microscopic linear mixing rule that is valid for arbitrarily complex plasmas over a wide range of Coulomb couplings. The microscopic mixing rule in turn implies and validates the linear mixing rule (LMR) for the equation of state properties and also the LMR for the electrical and thermal conductivities of dense MCPs. To make our result as useful as possible, for the specific cases of electrical and thermal conductivities, we provide a simple analytic fit that is valid for arbitrarily complex MCPs over a wide range of Coulomb couplings. We compute the thermal conductivity for a representative compositional profile of the outer crust of an accreting neutron star in which hundreds of nuclear species can be present. We utilize our results to re-examine the so-called impurity parameter formalism as used to characterize impure plasmas.

79 ASTRONOMY AND ASTROPHYSICS↗

Morphine and high-fat diet differentially alter the gut microbiota composition and metabolic function in lean versus obese mice

There are known associations between opioids, obesity, and the gut microbiome, but the molecular connection/mediation of these relationships is not understood. To better clarify the interplay of physiological, genetic, and microbial factors, this study investigated the microbiome and host inflammatory responses to chronic opioid administration in genetically obese, diet-induced obese, and lean mice. Samples of feces, urine, colon tissue, and plasma were analyzed using targeted LC-MS/MS quantification of metabolites, immunoassays of inflammatory cytokine levels, genome-resolved metagenomics, and metaproteomics. Genetic obesity, diet-induced obesity, and morphine treatment in lean mice each showed increases in distinct inflammatory cytokines. Metagenomic assembly and binning uncovered over 400 novel gut bacterial genomes and species. Morphine administration impacted the microbiome’s composition and function, with the strongest effect observed in lean mice. This microbiome effect was less pronounced than either diet or genetically driven obesity. Based on inferred microbial physiology from the metaproteome datasets, a high-fat diet transitioned constituent microbes away from harvesting diet-derived nutrients and towards nutrients present in the host mucosal layer. Considered together, these results identified novel host-dependent phenotypes, differentiated the effects of genetic obesity versus diet induced obesity on gut microbiome composition and function, and showed that chronic morphine administration altered the gut microbiome.

60 APPLIED LIFE SCIENCES↗

Improved stellarator permanent magnet designs through combined discrete and continuous optimizations

A common optimization problem in the areas of magnetized plasmas and fusion energy is the design of magnets to produce a given three-dimensional magnetic field distribution to high precision. When designing arrays of permanent magnets for stellarator plasma confinement, such problems have tens of thousands of degrees of freedom whose solutions, for practical reasons, should be constrained to discrete spaces. We perform a direct comparison between two algorithms that have been developed previously for this purpose, and demonstrate that composite procedures that apply both algorithms in sequence can produce substantially improved results. One approach uses a continuous, quasi-Newton procedure to optimize the dipole moments of a set of magnets and then projects the solution onto a discrete space. The second uses an inherently discrete greedy optimization procedure that has been enhanced and generalized for this work. Further, the approaches are both applied to design arrays cubic rare-Earth permanent magnets to confine a quasi-axisymmetric plasma with a magnetic field on axis of 0.5 T. The first approach tends to find solutions with higher field accuracy, whereas the second can find solutions with substantially (up to 30%) fewer magnets. When the approaches are combined, they can obtain solutions with magnet quantities comparable to the second approach while matching the field accuracy of the first.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Si quantum dots in silicon nitride: Quantum confinement and defects

Luminescence of amorphous Si quantum dots (Si QDs) in a hydrogenated silicon nitride (SiN{sub x}:H) matrix was examined over a broad range of stoichiometries from Si{sub 3}N{sub 2.08} to Si{sub 3}N{sub 4.14}, to optimize light emission. Plasma-enhanced chemical vapor deposition was used to deposit hydrogenated SiN{sub x} films with excess Si on Si (001) substrates, with stoichiometry controlled by variation of the gas flow rates of SiH{sub 4} and NH{sub 3} gases. The compositional and optical properties were analyzed by Rutherford backscattering spectroscopy, elastic recoil detection, spectroscopic ellipsometry, photoluminescence (PL), time-resolved PL, and energy-filtered transmission electron microscopy. Ultraviolet-laser-excited PL spectra show multiple emission bands from 400 nm (3.1 eV) to 850 nm (1.45 eV) for different Si{sub 3}N{sub x} compositions. There is a red-shift of the measured peaks from ∼2.3 eV to ∼1.45 eV as Si content increases, which provides evidence for quantum confinement. Higher N content samples show additional peaks in their PL spectra at higher energies, which we attribute to defects. We observed three different ranges of composition where Tauc band gaps, PL, and PL lifetimes change systematically. There is an interesting interplay of defect luminescence and, possibly, small Si QD luminescence observed in the intermediate range of compositions (∼Si{sub 3}N{sub 3.15}) in which the maximum of light emission is observed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nanotube Production and Applications at Johnson Space Center

Promise of applications of carbon nanotubes has led to an intense effort at NASA/JSC, especially in the area of nanotube composites. Using the extraordinary mechanical strength of nanotubes, NASA hopes to design this revolutionary lightweight material for use in aerospace applications. Current research focuses on structural polymeric materials to attempt to lower the weight of spacecraft necessary for interplanetary missions. Other applications of nanotubes are also of interest for energy storage, gas storage, nanoelectronics, field emission, and biomedical applications. In pursuit of these goals, we have set up both laser and arc production processes for nanotubes. An in-depth diagnostic study of the plasma plume in front of the laser target has been studied to try to determine nanotube growth mechanisms. Complementary studies of characterization of nanotube product have added to knowledge of growth conditions. Results of our preliminary experiments in incorporating nanotubes into composites will be presented. Morphology and mechanical properties of the nanotubes composites will be discussed.

Nikolaev, Pavel↗

Dual-wavelength excited photoluminescence spectroscopy of deep-level hole traps in Ga(In)NP

By employing photoluminescence (PL) spectroscopy under dual-wavelength optical excitation, we uncover the presence of deep-level hole traps in Ga(In)NP alloys grown by molecular beam epitaxy (MBE). The energy level positions of the traps are determined to be at 0.56 eV and 0.78 eV above the top of the valance band. We show that photo-excitation of the holes from the traps, by a secondary light source with a photon energy below the bandgap energy, can lead to a strong enhancement (up to 25%) of the PL emissions from the alloys under a primary optical excitation above the bandgap energy. We further demonstrate that the same hole traps can be found in various MBE-grown Ga(In)NP alloys, regardless of their growth temperatures, chemical compositions, and strain. The extent of the PL enhancement induced by the hole de-trapping is shown to vary between different alloys, however, likely reflecting their different trap concentrations. The absence of theses traps in the GaNP alloy grown by vapor phase epitaxy suggests that their incorporation could be associated with a contaminant accompanied by the N plasma source employed in the MBE growth, possibly a Cu impurity.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Combined elemental and microstructural analysis of genuine and fake copper-alloy coins

Innovative noninvasive material analysis techniques are applied to determine archaeometallurgical characteristics of copper-alloy coins from Florence's National Museum of Archaeology. Three supposedly authentic Roman coins and three hypothetically fraudolent imitations are thoroughly investigated using laser-induced plasma spectroscopy and time of flight neutron diffraction along with 3D videomicroscopy and electron microscopy. Material analyses are aimed at collecting data allowing for objective discrimination between genuine Roman productions and late fakes. The results show the mentioned techniques provide quantitative compositional and textural data, which are strictly related to the manufacturing processes and aging of copper alloys. (laser applications)

36 MATERIALS SCIENCE↗

ON HELIUM MIXING IN QUASI-GLOBAL SIMULATIONS OF THE INTRACLUSTER MEDIUM

The assumption of a spatially uniform helium distribution in the intracluster medium (ICM) can lead to biases in the estimates of key cluster parameters if composition gradients are present. The helium concentration profile in galaxy clusters is unfortunately not directly observable. Current models addressing the putative sedimentation are one-dimensional and parametrize the presence of magnetic fields in a crude way, ignoring the weakly collisional, magnetized nature of the medium. When these effects are considered, a wide variety of instabilities can play an important role in the plasma dynamics. In a series of recent papers, we have developed the local, linear theory of these instabilities and addressed their nonlinear development with a modified version of Athena. Here, we extend our study by developing a quasi-global approach that we use to simulate the mixing of helium as induced by generalizations of the heat-flux-driven buoyancy instability (HBI) and the magnetothermal instability, which feed off thermal and composition gradients. In the inner region of the ICM, mixing can occur over a few gigayears, after which the average magnetic field inclination angle is ∼30°–50°, resulting in an averaged Spitzer parameter higher by about 20% than the value obtained in homogeneous simulations. In the cluster outskirts the instabilities are rather inefficient, due to the shallow gradients. This suggests that composition gradients in cluster cores might be shallower than one-dimensional models predict. More quantitative statements demand more refined models that can incorporate the physics driving the sedimentation process and simultaneously account for the weakly collisional nature of the plasma.

79 ASTRONOMY AND ASTROPHYSICS↗

Surface interactions of SO{sub 2} and passivation chemistry during etching of Si and SiO{sub 2} in SF{sub 6}/O{sub 2} plasmas

A variety of materials can be etched in SF{sub 6}/O{sub 2} plasmas. Here, the fate of SO{sub 2} at Si and SiO{sub 2} surfaces during etching in SF{sub 6}/O{sub 2} plasmas has been explored using the imaging of radicals interacting with surfaces method. The scattering of SO{sub 2} at Si and SiO{sub 2} surfaces was measured as a function of both the applied rf power and O{sub 2} addition to the plasma. For both surfaces, the surface scattering coefficient (S) of SO{sub 2} during etching is near unity and is largely unaffected by changing plasma parameters such as power and O{sub 2} addition. Notably the etch rate of Si increases monotonically with power, whereas the etch rate of SiO{sub 2} appears insensitive to changes in plasma conditions. As a result, the etch selectivity closely follows the trends of the Si etch rate. Etch rates are compared to other fluorine-containing plasma systems such as NF{sub 3}/O{sub 2} and C{sub 2}F{sub 6}/O{sub 2}. Using mass spectral data and optical emission spectra to characterize the gas phase species combined with compositional analysis from x-ray photoelectron spectroscopy data, the formation and roles of SO{sub 2} in Si and SiO{sub 2} etching are discussed and correlated with etch rate and other gas phase species such as F, O, and S{sub x}O{sub y}F{sub z}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Increased urine acylcarnitines in diabetic ApoE-/- mice: Hydroxytetradecadienoylcarnitine (C14:2-OH) reflects diabetic nephropathy in a context of hyperlipidemia

Hyperlipidemia is a risk factor for initiation and progression of diabetic nephropathy but the metabolic pathways altered in the diabetic kidney in a context of hyperlipidemia remain incompletely described. Assuming that changes in urine composition reflect the alteration of renal metabolism and function, we analyzed the urine metabolite composition of diabetic (streptozotocin-treatment) and control (non diabetic) ApoE−/− mice fed a high cholesterol diet using targeted quantitative metabolomics. Urine metabolome was also compared to the plasma metabolome of the same animals. As previously shown, urine albuminuria/urine creatinine ratio (uACR) and glomerular area and plasma lipids (cholesterol, triglycerides) were more elevated in diabetic mice compared to control. After adjustment to urine creatinine, the abundance of 52 urine metabolites was significantly different in diabetic mice compared to control. Among them was a unique metabolite, C14:2-OH (3-hydroxytetradecadienoylcarnitine) that, in diabetic mice, was positively and significantly correlated with uACR, glomerular hypertrophy, blood glucose and plasma lipids. That metabolite was not detected in plasma. C14:2-OH is a long-chain acylcarnitine reminiscent of altered fatty acid beta oxidation. Other acylcarnitines, particularly the short chains C3-OH, C3-DC, C4:1, C5-DC, C5-M-DC, C5-OH that are reminiscent of altered oxidation of branched and aromatic amino acids were also exclusively detected in urine but were only correlated with plasma lipids. Finally, the renal gene expression of several enzymes involved in fatty acid and/or amino acid oxidation was significantly reduced in diabetic mice compared to control. This included the bifunctional enoyl-CoA hydratase/3-hydroxyacyl-CoA (Ehhadh) that might play a central role in C14:2-OH production. This study indicate that the development of diabetes in a context of hyperlipidemia is associated with a reduced capacity of kidney to oxidize fatty acids and amino acids with the consequence of an elevation of urinary acetylcarnitines including C14:2-OH that specifically reflects diabetic nephropathy.

60 APPLIED LIFE SCIENCES↗

Innovative recycling of high purity silver from silicon solar cells by acid leaching and ultrasonication

Precious and scarce silver (Ag) is used as a front electrical contact in silicon solar panels. With massive amounts of solar panel waste coming to end-of-life, it is imperative to recover all the Ag from these modules. In this paper, we propose a novel method to easily reclaim Ag from end-of-life silicon solar cells using low concentration sulfuric acid (H 2 SO 4 ) leaching followed by ultrasonication. Our process simplifies the Ag recycling procedure by directly recovering the Ag contacts from solar cells, eliminating the need for secondary precipitation/electrodeposition. First, scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDX) and X-ray photoelectron spectroscopy (XPS) was used to study the leaching and ultrasonication process on rejected solar wafers. Next, a solar panel from landfill was heated in a furnace to burn off the polymer encapsulant. The silicon wafers were then collected from the burning process and leached in 2 M H 2 SO 4 at two different shaking speeds for 48 hours at room temperature. Finally, the end-of-life silicon wafer pieces were collected, sonicated in water, and then the sonication water was centrifuged to show a proof-of-concept to recover the Ag contacts. Inductively coupled plasma optical emission spectroscopy (ICPOES) is used to monitor dissolved elements in the leachate as a function of time and shaking speed. XPS is used to evaluate the composition of the silicon cell wafer surface before and after H 2 SO 4 leaching. SEM is used to image the recovered Ag contacts morphology and EDX confirms the recovered particles contain high amounts of Ag. Furthermore, a proposed schematic illustrates the authors’ hypothesis for the peeling mechanism.

14 SOLAR ENERGY↗

Refine your search to explore more results.