Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

Understanding the Impact of Fuel on Surfactant Microstructure of Firefighting Foam

Abstract Aqueous film-forming foam is being phased out due to the environmental impacts of fluorinated surfactants contained in the firefighting foams. To develop an environmentally friendly firefighting foam, it is important to understand the factors controlling the firefighting performance of surfactants. Fuel transport through foam has been considered as a dominant mechanism for foam collapse. Therefore, the impact of fuels (heptane, octane and trimethylbenzene (TMB)) on surfactant microstructure was studied for three different types of surfactants (Capstone, Glucopon, and siloxane) that have applications in firefighting foam. Multiple techniques were used to identify the microstructure and interfacial properties of surfactants with and without exposure to liquid fuel. The ignition time of fuel vapor through foam and solubility of fuel through liquid surfactant solution were measured as well. This work shows fuel solubility has an impact on the surfactant microstructure and interfacial properties. In addition, fuel solubility and vapor pressure affect the ignition time of fuel vapors.

Engineering↗

The effect of Nd substitution on the electrical properties of Bi{sub 3}NbTiO{sub 9} Aurivillius phase ceramics

The effect of Nd substitution on the microstructures and electrical properties of Aurivillius phase ferroelectric Bi{sub 3}NbTiO{sub 9}-based ceramics has been studied. All of the Bi{sub 3-x}Nd{sub x}NbTiO{sub 9} (0<=x<=1) ceramics are ferroelectrics. The Curie point T{sub C} decreased with increasing Nd doping content x. The Bi{sub 3-x}Nd{sub x}NbTiO{sub 9} ceramics exhibited a sharp ferroelectric-paraelectric phase transition at small x values (x<=0.6), whereas a diffuse phase transition was observed at higher x values (x>=0.8). Both the piezoelectric constant d{sub 33} and the dc electrical resistivity of Bi{sub 3}NbTiO{sub 9} ceramics were greatly enhanced by Nd substitution on the A sites. The improved properties can be attributed to the fact that Nd substitution depressed the generation of oxygen vacancies. A combination of high d{sub 33} values, high resistivity, and high T{sub C} points (>700 deg. C) suggests that the Bi{sub 3-x}Nd{sub x}NbTiO{sub 9} ceramics with x<=0.6 could be good candidates for high-temperature piezoelectric applications.

36 MATERIALS SCIENCE↗

AZ61 and AZ61-La Alloys as Anodes for Mg-Air Battery

AZ61 and AZ61-0.5La (wt.%) alloys are prepared by the conventional casting method and then, AZ61 and AZ61-0.5La alloy sheets are obtained with multi-pass hot rolling. Microstructures and electrochemical properties of four alloys are investigated, and discharge properties are tested by an assembled Mg-air battery using alloy anode sheets with a dimension of 70 × 100 × 2.5 mm. Results show that Al{sub 11}La{sub 3} phases are formed in as-cast AZ61-0.5La alloy and promote the grain refinement and the formation of uniform microstructure in as-rolled AZ61-0.5La alloy. As-rolled AZ61-0.5La alloy exhibits a weak self-corrosion tendency but a strong discharge activity. After discharge test for 5 h, the Mg-air battery based on the as-rolled AZ61-0.5La sheet can provide the maximum power output of 1.625 W, and as-rolled AZ61-0.5La anode can supply the maximum energy density of 1417 mWhg{sup −1}. In addition, the relationship between microstructures and discharge properties is sufficiently described and discussed in this paper.

36 MATERIALS SCIENCE↗

Characterization, organic modification of wollastonite coated with nano-Mg(OH){sub 2} and its application in filling PA6

Highlights: • Wollastonite is first inorganic modified by coating nano-Mg(OH){sub 2} and then organic modified with silane. • Filling 30% of this composite powder in PA6 the mechanical properties, the heat distortion temperature and oxygen index of the PA6 composites were notably enhanced. - Abstract: Nano-Mg(OH){sub 2} was deposited on the surface of wollastonite (MW) powder with heterogeneous nucleation method and then modified with silane. The microstructure and surface properties of wollastonite (W) and MW powders were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive X-ray spectrometry (EDS) and X-ray diffraction (XRD), respectively. The microstructure of W, MW and silane modified MW (SMW) powders were characterized by Fourier translation infrared spectroscopy (FTIR). The mechanical properties, heat distortion temperature (HDT) and oxygen index (OI) of PA6 composites having different fillers were discussed. It was shown that the surface of wollastonite was coated with a layer of 33 nm thickness of Mg(OH){sub 2} grains and the distribution of which was uniform. The number of the hydroxyl groups on the surface of wollastonite powder increased after coated with Mg(OH){sub 2}. Filling 30% of SMW powder in PA6 the mechanical properties, HDT and OI were notably enhanced.

36 MATERIALS SCIENCE↗

Dependence of stress-induced omega transition and mechanical twinning on phase stability in metastable β Ti–V alloys

Tensile properties and deformation microstructures of a series of binary β Ti–16–22V alloys have been investigated. The results show that the plastic deformation mode changes from the plate-like stress-induced ω phase transformation with a special habit plane of (− 5052){sub ω}//(3 − 3 − 2){sub β} to (332)<113> type deformation twinning with increasing the content of vanadium in the β Ti–16–22 wt.% V alloys. The plate-like stress-induced ω phase has a special orientation relationship with the β phase matrix, i.e., [110]{sub β}//[− 12 − 10]{sub ω}, (3 − 3 − 2){sub β}//(− 5052){sub ω} and (− 55 − 4){sub β}//(30 − 31){sub ω}. The alloys plastically deformed by stress-induced ω phase transformation exhibit relatively higher yield strength than those deformed via (332)<113> type deformation twinning. It can be concluded that the stability of β phase plays a significant role in plastic deformation mode, i.e., stress-induced ω phase transformation or (332)<113> type deformation twinning, which governs the mechanical property of the β Ti–16–22 wt.% V alloys. - Highlights: • Tensile properties and deformed microstructures of β Ti–16–22V alloys were studied. • Stress-induced ω phase transformation and (332)<113> twinning occur in the alloys. • Stability of β phase plays a significant role in plastic deformation mode. • Plastic deformation mode governs the mechanical property of the alloys.

36 MATERIALS SCIENCE↗

Influence of Sodium on the Tensile Properties of Optimized Grade 92 Steel

This report provides an update on the evaluation of sodium compatibility of advanced alloy, optimized Grade 92, and the reference materials. The report is a deliverable (Level 3) in FY15 (M3AT-15AN1602072), under the Work Package AR-15AN160207, “Sodium Compatibility” performed by Argonne National Laboratory (ANL), as part of Advanced Reactor Technologies program. This work package supports the advanced structural materials development by providing corrosion, microstructure, and tensile property data from the standpoint of sodium compatibility of advanced structural alloys. During this fiscal year, sodium exposure experiments were performed at 600°C in forced convection sodium loops at Argonne National Laboratory. The oxygen content of sodium was controlled by the cold-trapping method to achieve ≈1 wppm oxygen level. Specimens were removed from the sodium loop after a pre-determined exposure time for post-sodium-exposure-examination, including weight and thickness measurements, cross-sectional examinations, microhardness measurements, microstructural characterization, and tensile tests at the sodium exposure temperature. Data of sodium-exposed specimens were compared with thermal aging data obtained at 650°C to separate the effects of sodium exposures and thermal aging. This report adds to the results on corrosion performance, microstructure and tensile properties of ferritic-martensitic exposed to sodium at 600°C. Specimens of G92-0, Opt. G92-4, Opt. G92-4T, and G91-H30176 for times up to 8,200 h, and Opt. G92-8T for 1,653 h were exposed to sodium at 600°C.

36 MATERIALS SCIENCE↗

Microstructure evolution, enhanced aging kinetics, and mechanical properties of AA7075 alloy after friction extrusion

In the present study we utilized Friction Extrusion (FE) a solid phase processing technique to produce fully consolidated dense 5 mm rods of AA7075 alloy. The combination of large shear stresses and temperatures at the tool-billet interface during the FE process resulted in the formation of dynamically recrystallized ~2.0 μm equiaxed grains and fine uniformly distributed stable η (MgZn 2 ) precipitates ~25–100 nm in size. Formation of such a microstructure resulted in lower solutionizing temperature and times (flash annealing) as compared to the conventionally extruded counterparts. Here we demonstrate for the first time that the solutionizing times for the T6 heat treatment of AA7075 can be reduced by three times using this FE process. In addition to being an energy efficient process, FE also serves to improve the performance of AA7075 alloys by retaining their strength while enhancing the ductility of the material. The tensile data for samples that were flash annealed and artificially aged after FE processing showed exceptional increase in ultimate tensile strength by over 19% and yield strength by over 59%, compared with an as-FE-processed sample.

36 MATERIALS SCIENCE↗

The modification of BaCe{sub 0.5}Zr{sub 0.3}Y{sub 0.2}O{sub 3–δ} with copper oxide: Effect on the structural and transport properties

The effect of the content of CuO additive on the sinterability, phase composition, microstructure, and electrical properties of BaCe{sub 0.5}Zr{sub 0.3}Y{sub 0.2}O{sub 3–δ} proton-conducting material is studied. Ceramic samples were produced by the citrate–nitrate synthesis method with the addition of 0, 0.25, 0.5, and 1% CuO. It is shown that the relative density of the samples containing 0.5 and 1% CuO is higher than 94% at a sintering temperature of 1450°C, whereas the relative density of the material is no higher than 85% at a lower content of the sintering additive. From the data of X-ray diffraction analysis and scanning electron microscopy, it is established that the introduction of a small CuO content (0.25%) is inadequate for single-phase and high-dense ceramics to be formed. The conductivity and scanning electron microscopy data show that the sample with BaCe{sub 0.5}Zr{sub 0.3}Y{sub 0.2}O{sub 3–δ} + 0.5% CuO composition possesses high total and ionic conductivities as well as a high degree of microstructural stability after hydrogen reduction of the ceramics. The citrate–nitrate method modified by the introduction of a small CuO content can be recommended for the production of single-phase, gas-tight, and high-conductivity electrolytes based on both BaCeO{sub 3} and BaZrO{sub 3}.

36 MATERIALS SCIENCE↗

An approach to combine neutron and ion irradiation data to accelerate material qualification for nuclear reactors

Next-generation nuclear power plants are generally characterized by higher operating temperatures, increased neutron fluences and energies, and distinct corrosive coolant environments versus the existing light water reactor fleet. Whether using existing materials in new environments, newly developed materials tailored for these environments, or new manufacturing methods, the traditional decades-long approach for materials qualification does not facilitate rapid deployment. Ion irradiation has demonstrated success in reproducing material microstructure and select property evolution resulting from neutron irradiation with three to four orders of magnitude reduction in time and cost, making it an ideal candidate for accelerated irradiation testing. Because microstructure has a large impact on bulk material properties, limited neutron irradiation data at lower damage levels can in principle be combined with accelerated ion testing results and modeling and simulation to form an accurate prediction of microstructure evolution and select properties under different neutron irradiation conditions and at higher damage levels. The objective of this work is to present a conceptual framework of specific steps to fulfill several technical challenges associated with qualifying materials for performance in radiation environments on an accelerated time frame. A brief review of the regulatory landscape for materials in nuclear environments is presented, followed by additional overviews to understand the current state of the art for correlation of materials properties across radiation environments using experimental and computational methodologies. Finally, the roles of academia, national laboratories, and industry in the advancement of this accelerated materials qualification framework are discussed as a path forward, with possible case studies presented.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Controlling mechanical properties of laser powder bed fused AlSi10Mg through manipulation of laser scan rotation

The microstructure and mechanical properties of laser powder bed fused (LPBF) AlSi10Mg alloys can be controlled by many processing parameters. This study focuses on the scan rotation angle, α, between adjacent layers, and establishes the relationship between α and tensile behavior of the as-built LPBF-processed AlSi10Mg alloy. Near-full density cubic coupons were manufactured using the same processing parameters but with systematic variation of α from 0° to 90°. Microscopic observations and X-ray diffraction analysis showed that differences among various coupons mainly include orientations of the melt pools with respect to the build direction and development of the crystallographic texture. The α=0° coupon and α=30° coupon showed the highest and lowest texture index, although the overall crystallographic texture was mild. Tensile specimens were manufactured horizontally and vertically using either α=0° or α=30°, but with various first layer laser direction with respect to the build plate. Notably, the α=0° specimen that was tested along the laser scan direction showed the largest yield strength (283 MPa) and highest tensile ductility (10.1 %). Quantitative image analysis and fractography were performed on all specimens. Results showed that the melt pool orientation with respect to the tensile direction affected the tensile behavior across the different specimens. This was closely related to the localized strain distribution within the melt pool and along the melt pool boundary for the different melt pool orientations observed. Further, these results demonstrate that the laser scan rotation angle between layers can be used to fine tune the mechanical properties of LPBF AlSi10Mg alloy.

36 MATERIALS SCIENCE↗

Study of retained austenite and nano-scale precipitation and their effects on properties of a low alloyed multi-phase steel by the two-step intercritical treatment

Microstructure evolution and properties were studied in a low carbon low alloyed hot-rolled bainitic steel by annealing and annealing plus tempering. Microstructure of the hot-rolled steel consists of lath bainite and martensite. By annealing at 720 °C for 30 min and water quenching, multi-phase microstructure consisting of intercritical ferrite, tempered bainite/martensite, retained austenite and fresh martensite was obtained. With increasing annealing temperature to 760 °C, microstructure of the steel consisted of intercritical ferrite, fresh martensite without retained austenite. After the second step of tempering at 680 °C for samples annealed both at 720 °C and 760 °C, ~ 8–9% volume fraction of retained austenite was obtained in the multi-phase microstructure. Moreover, fine precipitates of VC with size smaller than 10 nm and copper precipitates with size of ~ 10–50 nm were obtained after tempering. Results from scanning transmission electron microscopy (STEM) give evidence to support that the partitioning of Mn, Ni and Cu is of significance for retained austenite stabilization. Due to the combined contribution of multiphase microstructure, the transformation-induced-plasticity effect of retained austenite and strengthening effect of nanometer-sized precipitates, yield strength greater than 800 MPa, yield to tensile ratio of 0.9, uniform elongation of ~ 9% and good low temperature impact toughness of 147 J at − 40 °C were achieved. - Highlights: • Stable retained austenite was produced in a low alloyed steel. • Partition of Mn, Ni and Cu was confirmed by STEM for austenite stabilization. • Nano-sized VC and Cu precipitates were achieved by second tempering. • High strength–high toughness with low Y/T ratio was obtained.

36 MATERIALS SCIENCE↗

Effects of thickness and orientation on the small scale fracture behaviour of additively manufactured Ti-6Al-4V

Highlights: • Miniaturized specimens successfully additively manufactured via SLM and SEBM. • Small-scale tensile testing of specimens to capture orientation/thickness effect. • Tomography characterization of defects. • Location dependence of fracture behavior. - Abstract: The effects of sample location, orientation, and thickness on the microstructure and resulting tensile properties of miniature SLM and SEBM AM samples of Ti-6Al-4V has been determined. Microstructure and mechanical property variations in the miniature samples are shown to be related to build orientation and also partly to specimen thickness and position within the build chamber. The present work is our initial attempt to develop a systematic approach for characterization of the microstructure (including defects via tomography) and mechanical properties on miniature AM test specimens that can also be used to reveal issues related to process stability (e.g. fluctuations in build conditions). The discussion is also included regarding their relevance to miniature samples that can be manufactured along with parts, excised from larger samples, and/or excised from actual manufactured components.

36 MATERIALS SCIENCE↗

Microstructural and nanomechanical studies of PVD Cr coatings on SiC for LWR fuel cladding applications

The microstructure and nanomechanical properties of pure Cr coatings deposited on SiC with various physical vapor deposition (PVD) methods have been investigated for the mitigation of hydrothermal corrosion of SiC-SiC f (SiC fiber-reinforced SiC matrix) composite fuel cladding in light water reactors (LWR). Cr coatings (4–7 μm thick) were deposited on unbiased SiC substrates using six variants of magnetron sputtering processes: (i) standard (S-DCMS), (ii) pulsed (P-DCMS), (iii) ion-assisted (I-DCMS), and (iv) pulsed ion-assisted direct current magnetron sputtering (PI-DCMS), (v) high-power impulse magnetron sputtering (HiPIMS), and (vi) bipolar HiPIMS (B-HiPIMS). Microstructural characterization and nanoindentation testing were used to evaluate effects of deposition technique on coating microstructure and nanomechanical properties. The application of positive reverse pulses to the sputter target induced coarsening of the columnar grain structure, while ion bombardment of substrates during deposition promoted densification of the coating microstructure. Both effects are exemplified in B-HiPIMS deposition, resulting in a high-density microstructure with compressive residual stress. Material pile-up around nano-indents and plastic work during nanoindentation were analyzed to understand deformation behavior of the coatings. Finally, the results suggest the B-HiPIMS process to be among the promising methods for the deposition of Cr coatings on SiC-SiC f for LWR cladding application.

36 MATERIALS SCIENCE↗

Fabrication of Titanium-Niobium-Zirconium-Tantalium Alloy (TNZT) Bioimplant Components with Controllable Porosity by Spark Plasma Sintering

Spark Plasma Sintering (SPS) is used to fabricate Titanium-Niobium-Zirconium-Tantalum alloy (TNZT) powder—based bioimplant components with controllable porosity. The developed densification maps show the effects of final SPS temperature, pressure, holding time, and initial particle size on final sample relative density. Correlations between the final sample density and mechanical properties of the fabricated TNZT components are also investigated and microstructural analysis of the processed material is conducted. A densification model is proposed and used to calculate the TNZT alloy creep activation energy. The obtained experimental data can be utilized for the optimized fabrication of TNZT components with specific microstructural and mechanical properties suitable for biomedical applications.

36 MATERIALS SCIENCE↗

Microstructure evolution, grain morphology variation and mechanical property change of Cu-Sn intermetallic joints subjected to high-temperature aging

Highlights: • The δ-Cu{sub 41}Sn{sub 11} could be formed by reaction of 11Cu{sub 3}Sn + 9Cu → Cu{sub 41}Sn{sub 11} during aging above 350 °C. • The temperature effects on the growth rate and grain morphology of Cu{sub 41}Sn{sub 11} phase were found. • The Cu{sub 41}Sn{sub 11} joints with refined grains exhibited higher hardness and shear strength. • The Cu{sub 41}Sn{sub 11} joints exhibited a combination of transgranular and intergranular fracture during shear test. - Abstract: In this work, the aging treatment was carried out on full Cu{sub 3}Sn joints at different temperatures for various durations, the microstructure evolution, grain morphology variation and mechanical property change of joints were investigated. The temperature effects on the growth rate and grain morphology of Cu{sub 41}Sn{sub 11} phase were found: The complete transformation from Cu{sub 3}Sn phase to Cu{sub 41}Sn{sub 11} phase in joints needed 300 h at 400 °C, but 4 h at 500 °C. The Cu{sub 41}Sn{sub 11} phase formed at 400 °C consisted of columnar grains with an average width of 23.5 μm, while the Cu{sub 41}Sn{sub 11} phase formed at 500 °C consisted columnar grains with an average width of 8.5 μm. The average hardness and shear strength values of the Cu{sub 41}Sn{sub 11} joints formed at 400 °C were 432.5 HV and 62 MPa, while the joints formed at 500 °C exhibited higher hardness and shear strength (451.5 HV and 65 MPa). Besides, the Cu{sub 41}Sn{sub 11} joint was found to exhibit a combination of transgranular and intergranular fracture during shear test.

36 MATERIALS SCIENCE↗

Analysis of integrity and microstructure of linear friction welded Waspaloy

Nickel-base superalloy, Waspaloy, was linear friction welded (LFWed) under different axial shortening conditions of 2.0, 3.4, and 4.6 mm. The tensile properties and microhardness of the weldments were investigated in the as-LFWed condition and compared with those in the post-weld heat treated (PWHTed) condition. Mechanical properties were related to microstructures following examination by optical microscopy, high resolution scanning electron microscopy, and electron backscatter diffraction (EBSD). Analyses of the EBSD results in terms of the misorientation angle distribution, which represents the stored energy, were performed. In the as-LFWed condition, the yield strength (YS) and ultimate tensile strength (UTS) increased with axial shortening due to greater expulsion of the softened interfacial material toward the periphery as flash. In contrast, with increasing axial shortening the total elongation initially remained constant and then decreased. This was also related to the expulsion of the softened interfacial material into the bifurcated flash. Extensive dissolution of the strengthening phase (γ′) in the weld area during linear friction welding (LFW) contributed to the lower YS and UTS in the as-welded condition compared to the PWHTed condition where the γ′ particles were recovered. After performing post-weld heat treatment (PWHT), the total elongation improved due to the relaxation of stored energy and grain growth in the thermomechanically affected zone (TMAZ). - Highlights: • Tensile property and microstructure in Waspaloy linear friction welds were studied. • Yield strength and ultimate tensile strength increased with axial shortening. • Elongation initially remained constant and then decreased with axial shortening. • Post-weld heat treat recovered dissolved γ′ particles and increased weld strength. • Stored energy relaxation during post-weld heat treatment improved weld elongation.

36 MATERIALS SCIENCE↗

Gradient process parameter optimization in additive friction stir deposition of aluminum alloys

As one of the most novel additive manufacturing methods, currently selection and optimization of processing parameters in additive friction stir deposition (AFSD) have mainly relied on experiments and subsequent characterization of microstructural and mechanical properties. Such approaches are both time- and resource-consuming. Therefore, an ultrasound elastography enhanced gradient process parameter optimization method was applied in the present work to obtain a window of optimized processing parameters for AFSD processing of aluminum alloy by varying both rotational and linear deposition speeds. Further, the quality of AFSD processed layer was investigated for physical nature of surface, dynamic elastic modulus, and microstructural aspects in cross-sections of the deposited layer. The efficiency in exploring process parameters was significantly enhanced by implementing a high-throughput screening experimental design based on application of gradient process parameters and continuous ultrasound elastographs. In addition, the applied ultrasonic elastography technique assisted in evaluating the homogeneity in microstructure and mechanical properties of AFSD sample over the entire gradients of the process parameters. The techniques adopted in current work can be further extended to identify suitable parameters for AFSD fabrication of components with desired mechanical properties such as hardness, fatigue, etc.

36 MATERIALS SCIENCE↗

Influence of microstructural heterogeneities on small-scale mechanical properties of an additively manufactured Al-Ce-Ni-Mn alloy

Laser powder bed fusion-based additive manufacturing (AM) is a promising method to fabricate creep-resistant Al-rare earth alloys (Al-Ce-Ni-Mn) with stable microstructures at up to 400°C. However, creep testing of these alloys at high temperatures shows that void coalescence and failure initiation occurs along the melt pool boundaries in the microstructure. Hence it is crucial to understand how the local mechanical behavior of the melt pool boundaries would influence the global properties of the AM produced alloy. In this study, in situ nanoindentation conducted at room temperature and 300°C revealed a reduced hardness at the melt pool boundaries. Similarly, micro-pillar compression showed a slight decline in yield strength at these boundaries, indicating that they are the weak spots in the microstructure. Such multimodal local mechanical property studies are necessary for understanding the influence of melt pool boundaries on the bulk response of fusion-based AM alloys.

36 MATERIALS SCIENCE↗

Refine your search to explore more results.