Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LIGNIN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

Scalable aqueous-phase fabrication of reduced graphene oxide nanofiltration membranes by an integrated roll-to-roll (R2R) process

Economic fractionation of multicomponent biomass-derived streams is a key challenge in biobased fuels and chemicals production. Kraft black liquor (BL) is generated at ~1 billion tons/yr globally from biomass pulping and contains ~15wt% total solids including lignin, hemicellulose fragments, and inorganics. Membrane-based BL concentration is attractive but challenged by low solute rejections and poor stability in BL, which combines alkaline pH (~13), high dissolved solids content (15+ wt%) and high temperature (70–85°C). Here we discuss the scaled fabrication and characterization of reduced graphene oxide (rGO) nanofiltration membranes by slot die coating on a roll-to-roll (R2R) with integrated vacuum filtration. Here, we obtain high-quality 90×30 cm rGO membranes (referred to as “R2R-rGO membranes” in this work) with ~100 nm average thickness supported on porous poly(ethersulfone) (PES) sheets, and an effective area of 2700cm 2 . We present characterizations of their microstructure and uniformity as mapped over large areas by scanning electron microscopy (SEM), ellipsometry, adhesion test and X-ray photoelectron spectroscopy (XPS). The constructed ellipsometry model for the rGO membrane/PES substrate composite was successfully applied to 48 different locations of the R2R-rGO membranes. The R2R-rGO membranes showed >98% lignin rejection with a steady state flux of ~12 LMH at 50bar in a 15.7wt% total solids (TS) kraft BL stream at 72°C and 2–3 gal/min crossflow rates. Slot die coating on a R2R platform with integrated vacuum filtration can enable rapid fabrication of high-quality GO membranes at scale without organic solvents or volatile organic compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Plant organic matter inputs exert a strong control on soil organic matter decomposition in a thawing permafrost peatland

Peatlands are climate critical carbon (C) reservoirs that could become a C source under continued warming. A strong relationship between plant tissue chemistry and the soil organic matter (SOM) that fuels C gas emissions is inferred, but rarely examined at the molecular level. Here we compared Fourier transform infrared (FT-IR) spectroscopy measurements of solid phase functionalities in plants and SOM to ultra-high-resolution mass spectrometric analyses of plant and SOM water extracts across a palsa-bog-fen thaw and moisture gradient in an Arctic peatland. From these analyses we calculated the C oxidation state (NOSC), a measure which can be used to assess organic matter quality. Palsa plant extracts had the highest NOSC, indicating high quality, whereas extracts of Sphagnum, which dominated the bog, had the lowest NOSC. The percentage of plant compounds that are less bioavailable and accumulate in the peat, increases from palsa (25%) to fen (41%) to bog (47%), reflecting the pattern of percent Sphagnum cover. The pattern of NOSC in the plant extracts was consistent with the high number of consumed compounds in the palsa and low number of consumed compounds in the bog. However, in the FT-IR analysis of the solid phase bog peat, carbohydrate content was high implying high quality SOM. Here, we explain this discrepancy as the result of low solubilization of bog SOM facilitated by the low pH in the bog which makes the solid phase carbohydrates less available to microbial decomposition. Plant-associated condensed aromatics, tannins, and lignin-like compounds declined in the unsaturated palsa peat indicating decomposition, but lignin-like compounds accumulated in the bog and fen peat where decomposition was presumably inhibited by the anaerobic conditions. A molecular-level comparison of the aboveground C sources and peat SOM demonstrates that climate-associated vegetation shifts in peatlands are important controls on the mechanisms underlying changing C gas emissions.

54 ENVIRONMENTAL SCIENCES↗

Advanced nuclear reactor integration opportunities for the pulp and paper industry in the U.S. context: Technical perspectives, gap analysis, and preliminary technoeconomic assessment

Pulp and paper (P&P) manufacturing requires a large amount of low-pressure (LP) steam to digest, wash wood fibers and dry pulp into paper. Most of the LP steam is extracted from backpressure turbines that produce power from high-pressure (HP) steam. This HP steam is generated from burning wood waste material; bark is burned in hog boilers, and lignin is boiled in a black liquor recovery boiler. In a typical integrated P&P mill, 50–100% of the steam is produced from these sources, while additional steam is produced in natural gas (NG), fuel oil, or coal boilers. The other energy-intensive process in the plant is the chemical-recovery section (e.g., lime kiln), which requires high-temperature processing from NG combustion to retrieve and recirculate spent chemicals. This paper assesses the energy and heat demand and material balances of a typical generic kraft pulp mill, along with the nuclear heat, steam, and power integration opportunities to replace conventional combustion systems. The paper also addresses steam and electricity generation through a comprehensive technical and engineering gap analysis of five different nuclear-integration opportunities and their process economics, thus enabling the lignin and bark to be further processed into biobased chemicals or fuels, as well as the potential to reduce overall emissions from kraft pulping. Preliminary findings have shown that the P&P industry could achieve technological benefits by integrating their current manufacturing process with small modular nuclear reactors (SMNRs) on a national level. This research aims to set the path forward for a cleaner and more resilient P&P industry.

Advanced nuclear reactor↗

Debottlenecking 4-hydroxybenzoate hydroxylation in Pseudomonas putida KT2440 improves muconate productivity from p -coumarate

The transformation of 4-hydroxybenzoate (4-HBA) to protocatechuate (PCA) is catalyzed by flavoprotein oxygenases known as para-hydroxybenzoate-3-hydroxylases (PHBHs). In Pseudomonas putida KT2440 (P. putida) strains engineered to convert lignin-related aromatic compounds to muconic acid (MA), PHBH activity is rate-limiting, as indicated by the accumulation of 4-HBA, which ultimately limits MA productivity. Here, we hypothesized that replacement of PobA, the native P. putida PHBH, with PraI, a PHBH from Paenibacillus sp. JJ-1b with a broader nicotinamide cofactor preference, could alleviate this bottleneck. Biochemical assays confirmed the strict preference of NADPH for PobA, while PraI can utilize either NADH or NADPH. Kinetic assays demonstrated that both PobA and PraI can utilize NADPH with comparable catalytic efficiency and that PraI also efficiently utilizes NADH at roughly half the catalytic efficiency. The X-ray crystal structure of PraI was solved and revealed absolute conservation of the active site architecture to other PHBH structures despite their differing cofactor preferences. To understand the effect in vivo, we compared three P. putida strains engineered to produce MA from p-coumarate (pCA), showing that expression of praI leads to lower 4-HBA accumulation and decreased NADP+/NADPH ratios relative to strains harboring pobA, indicative of a relieved 4-HBA bottleneck due to increased NADPH availability. In bioreactor cultivations, a strain exclusively expressing praI achieved a titer of 40 g/L MA at 100% molar yield and a productivity of 0.5 g/L/h. Altogether, this study demonstrates the benefit of sampling readily available natural enzyme diversity for debottlenecking metabolic flux in an engineered strain for microbial conversion of lignin-derived compounds to value-added products.

09 BIOMASS FUELS↗

NMR of Fully and Partially 13 C-Enriched Biomass Enhances Pendent Group Structural Characterization

Traditional solution-state NMR experiments may either fail or yield unsatisfactory results when employing fully- 13 C-labeled biomass due to complications arising from 13 C– 13 C coupling. Constant-time analogs of HSQC experiments mitigate such issues and deliver enhanced sensitivity. A rarely reported CT-HSQC-TOCSY experiment allows the proton coupling network to deliver much of the same value as the parent experiment on unlabeled or 10–15%- 13 C-labeled biomass polymers but with enhanced sensitivity. In the absence of a viable HMBC analog for long-range correlations, a relayed C–C experiment, i.e., via directly bonded 13 C-labeled networks, enables the reliable assignment of coupled carbons, with the added advantage of correlating the more elusive quaternaries. A C–C-FLOPSY experiment takes advantage of fully- 13 C-labeled materials for mapping extensive carbon networks in the complex polymer mixtures inherent in biomass. Various pendent groups (tricin units, cis- and trans-p-coumarates, and p -hydroxybenzoates) that adorn lignins, and the cis- and trans-ferulates on arabinoxylan polysaccharides, are exquisitely revealed in spectra from isolated lignins or whole-cell-wall materials from maize, sorghum, and poplar.

biopolymers↗

Nanoscale Examination of Chemical and Enzymatic Degradation of Plant Cell Walls

Lignocellulosic materials present the largest source of biomass for biotechnology and green energy. This study aimed at better understanding the cell wall disintegration mechanisms relevant for the biochemical conversion of biomass to carbohydrates. Herein, we examined nanoscale changes in cell wall structure and composition upon industrially relevant chemical and enzymatic treatments to achieve the desired level of breakdown. One treatment involved hydrogen peroxide and acetic acid to remove lignin. Another modification used the cellulase enzyme for cell wall degradation. Band excitation contact resonance atomic force microscopy was used to visualize and mechanically characterize cell wall layers. After cellulase treatments, we detected microcracks across the cell wall. Wet-chemical, Fourier-transform infrared and Raman spectroscopic analyses confirmed the removal of lignin and extractives through acid bleaching, while the enzymatic treatment minimally affected the biopolymer composition. Delignification resulted in cell wall delamination and reduced stiffness. In conclusion, X-ray diffraction revealed changes in cellulose structure and crystallinity.

Soini, Steven A. [Florida Atlantic Univ., Boca Rat↗

Novel Strategy To Analyze Fourier Transform Ion Cyclotron Resonance Mass Spectrometry Data of Biomass Pyrolysis Oil for Oligomeric Structure Assignment

Among the most prominent challenges for the analysis of biomass pyrolysis products is the characterization of the abundant oligomer fraction of bio-oil. This fraction is principally made up of pyrolytic lignins and dehydrated, highly modified sugar oligomers, called humins, in liquid phase. An emerging technique for analysis of this oligomer fraction is high-resolution Fourier transform-ion cyclotron resonance mass spectrometry (FT-ICR MS), which allows for accurate determination of C x H y O z formulae for detected oligomers. Additionally, using simple dehydration and fragmentation reaction schemes, similar formulae can be developed from cellulose-, hemicellulose- and lignin-derived oligomers, which are primary depolymerization products. In this paper, FT-ICR MS analysis is coupled with combinatoric dehydration and fragmentation modeling in order to match experimentally detected bio-oil oligomers with hypothetical pathways for their formation during pyrolysis. In this way, we present a novel strategy by which oligomeric structures can be proposed for bio-oils. Using this approach, it becomes possible to advance the understanding of both the molecular structures comprising the bio-oil oligomer fraction and the pathways by which these structures form during biomass pyrolysis reactions.

09 BIOMASS FUELS↗

Ternary Phase Diagram of Water/Bio-Oil/Organic Solvent for Bio-Oil Fractionation

Separating bio-oil by fractionation with different chemical composition is a critical step to refine these oils and obtain high value products. Cold-water precipitation of pyrolytic lignin from bio-oil is the most common approach used. However, the obtained aqueous phase from this method still contain phenols, is diluted and difficult to use. In this study, the use of liquid-liquid extraction with different solvents (1-butanol, ethyl acetate, 1-octanol, dichloromethane, toluene, and hexane) for the separation of targeted molecules (lignin oligomers, sugars, acetic acid) is explored. Ternary phase diagrams for the organic solvent/water/bio-oil are reported. The partition coefficient of compounds of interest (both light and heavy fraction) is reported for the liquid-liquid equilibrium zone. When using butanol as solvent, the highest separation factor of total phenols over total sugars was observed. Furthermore, our results provide information to design L-L separation units with the capacity to selectively recover targeted molecules from pyrolysis oils.

09 BIOMASS FUELS↗

Co-hydrotreatment of Bio-oil and Waste Cooking Oil to Produce Transportation Fuels

This paper reports the co-hydrotreatment of the heavy bio-oil fraction with waste cooking oil (WCO) using NiMo/γ-Al 2 O 3 catalyst, followed by the distillation of resulting deoxygenated oil and the characterization of resulting fuel cuts. The heavy BTG bio-oil fraction was obtained by removing the very reactive light-oxygenated compounds via rotary evaporation, subsequently mixed with 1-butanol. The resulting oil was blended with WCO and subjected to a two-step co-hydrotreatment process. The first step, called “stabilization,” is aimed at saturating highly reactive hydrogen-deficient compounds. The second step, called “deoxygenation,” aimed to remove bio-oil oxygen, primarily as H 2 O. This study examined the impact of varying bio-oil concentrations (0, 10, 20, 30, 40 wt.% of WCO) on the upgraded oil's yield, composition, and fuel properties. The resulting hydrotreated oil was distilled into gasoline-range, kerosene-range, and diesel-range hydrocarbons at <150 °C, 150 to 250 °C, and 250 to 350 °C, respectively. The yield of the hydrotreated oil indicates that as the bio-oil concentration increases, the amounts of coke (0.7 to 2.4 %) and water (2 to 10 wt. %) increase while the organic layer yields decrease (80 to 63 %). The coke yield was comparable to the coke yield obtained when co-processing the pyrolytic lignin fraction. This suggests that coke is formed from both the sugar oligomers and the lignin-derived oligomers. The UV-fluorescence analysis on the hydrotreated oil shows that more polycondensed and conjugated ring compounds formed as the bio-oil concentration is increased. These compounds are precursors of coke. FTIR results showed that most raw materials were converted to biofuels after the hydrotreatment. To achieve less than 1 wt. % of coke yield, blends with up to 20 wt. % pyrolysis oil should be used. An increase in bio-oil concentration leads to a slight increase in gasoline yield and a decrease in kerosene and diesel yields. The identified carbon species found in the fuel cuts include n-paraffin, iso-paraffin, cycloparaffin, and aromatics. Further, the jet fuel cut (kerosene) was characterized by density, surface tension, and viscosity. Our product conforms to the standard specifications for sustainable aviation fuels (Jet A-1). Further research is suggested to fine-tune the operating parameters for achieving reduced coke yield and enhanced kerosene yield.

09 BIOMASS FUELS↗

Challenges and Opportunities for Bio-oil Refining: A Review

Bio-oil derived from fast pyrolysis of lignocellulosic materials is among the most complex and inexpensive raw oils that can be produced today. Although commercial or demonstration scale fast pyrolysis units can readily produce this oil, this industry has not grown to significant commercial impact due to the lack of bio-oil market pull. This paper is a review of the challenges and opportunities for bio-oil upgrading and refining. Pyrolysis oil consists of six major fractions. (water 15-30 wt.%, light oxygenates, 8-26 wt.%. mono-phenols, 2-7 wt.%, water insoluble oligomers derived from lignin 15-25wt.%, and water soluble havey molecules 10-30 wt.%). The composition of water-soluble oligomers is relatively poorly studied. In the 1880s, bio-oil refining (formally known as wood distillation) targeted the separation and commercialization of C1-C4 light oxygenated compounds to produce methanol, acetic acid and acetone with the commercialization of the lignin derived water insoluble fraction for preserving wooden sailing vessels against rot. More recently the company Ensyn extracted and commercialized condensed natural smoke as a food additive. Most research efforts in the last twenty years have focused on the two-step hydrotreatment concept for the production of transportation fuels. In spite of major progress this concept remains at the demonstration. In this review, the opportunities and progress to separate bio-oil fractions and chemicals, mainly acetic acid (HAc), hydroxyacetaldehyde (HHA) and acetol, and convert them into value added co-products are thoroughly discussed. In spite of the large number of separation schemes and products tested, very few of them have been studied as part of fully integrated bio-oil refinery concepts. Furthermore, the synthesis, techno-economic and environmental evaluation of novel integrated bio-oil refinery concepts is likely to become a subject of intense research activity in the coming years.

09 BIOMASS FUELS↗

Redox Fluctuations Control the Coupled Cycling of Iron and Carbon in Tropical Forest Soils

In this paper, oscillating redox conditions are a common feature of humid tropical forest soils, driven by an ample supply and dynamics of reductants, high moisture, microbial oxygen consumption, and finely textured clays that limit diffusion. However, the net result of variable soil redox regimes on iron (Fe) mineral dynamics and associated carbon (C) forms and fluxes is poorly understood in tropical soils. Using a 44-day redox incubation experiment with humid tropical forest soils from Puerto Rico, we examined patterns in Fe and C transformations under four redox regimes: static anoxic, "flux 4-day" (4d oxic, 4d anoxic), "flux 8-day" (8d oxic, 4d anoxic) and static oxic. Prolonged anoxia promoted reductive dissolution of Fe-oxides, and led to an increase in soluble Fe(II) and amorphous Fe oxide pools. Preferential dissolution of the less-crystalline Fe pool was evident immediately following a shift in bulk redox status (oxic to anoxic), and coincided with increased dissolved organic C, presumably due to acidification or direct release of organic matter (OM) from dissolving Fe(III) mineral phases. The average nominal oxidation state of water-soluble C was lowest under persistent anoxic conditions, suggesting that more reduced organic compounds were metabolically unavailable for microbial consumption under reducing conditions. Anoxic soil compounds had high H/C values (and were similar to lignin-like compounds) whereas oxic soil compounds had higher O/C values, akin to tannin- and cellulose-like components. Cumulative respiration derived from native soil organic C was highest in static oxic soils. These results show how Fe minerals and Fe-OM interactions in tropical soils are highly sensitive to variable redox effects. Shifting soil oxygen availability rapidly impacted exchanges between mineral-sorbed and aqueous C pools, increased the dissolved organic C pool under anoxic conditions implying that the periodicity of low-redox events may control the fate of C in wet tropical soils.

54 ENVIRONMENTAL SCIENCES↗

Understanding and Mitigating Stickiness in Biochar Produced through Acid Hydrolysis and Dehydration

Levulinic acid is a platform chemical with significant potential for conversion into a wide range of biobased chemicals and fuels. A common process for producing levulinic acid from lignocellulosic feedstocks involves acid hydrolysis and dehydration (AHDH), where hexose polymers are hydrolyzed into monomeric sugars and subsequently dehydrated to levulinic acid and formic acid in the presence of dilute sulfuric acid. However, scaling the AHDH process is challenging because of the formation of byproducts such as sticky biochar, which accumulates in continuous-flow reactors, reducing effective reaction volume and increasing process downtime. This study investigates the effect of a chemical preconditioning step on mitigating sticky biochar formation. Woody biomass was preconditioned at 170 °C with 0.26 wt % sulfuric acid for 30 min, resulting in substantial removal of hemicellulose and acid-soluble lignin. AHDH of these preconditioned solids produced biochar that did not adhere to reactor surfaces. TGA analysis confirmed that the chemical preconditioning step minimized interactions between hemicellulose-derived degradation products and lignin side chains, reducing sticky char formation. Additionally, the study observed a 6% higher yield of organic acids from softwood species compared to hardwoods, with bark content shown to negatively impact yield. These findings suggest that targeted preconditioning of lignocellulosic biomass can enhance reactor operability and improve organic acid production efficiency in AHDH processes.

biopolymers↗

Manufacturing of Continuous Microporous Polymeric Fibers for Separation Applications

Polyolefin plastic waste, particularly polypropylene, is one of the most prevalent components in the plastic waste stream generated globally. However, only a small fraction of this waste is recycled and reintegrated into second applications. These materials have significant embedded energy that could be used for additional productivity if recycled properly. Therefore, there is a critical need to develop scalable processing techniques with high throughput to effectively recycle it. We report the continuous manufacturing of microporous fibers using waste polypropylene plastic and melt-processable lignin, a plant biomass constituent produced as a byproduct in paper mills or biorefineries, as a template to create pores. Further, these filaments with hierarchical porosity─created by controlled microphase separation during high-speed extensional flow followed by removal of lignin─exhibit exceptional capillary action for hydrophobic liquids. The resulting porous fibers can be used for various separation applications. For example, the oil uptake of the fibers is 9.59 ± 0.82 g/g for applications in oil recovery in bodies of water. In addition, polyethylenimine infiltration within these nanoporous fibers introduces cyclic room temperature sorption and thermal desorption potential of acidic gases such as CO 2 in a bench-scale experiment. The fibers exhibit multiple cycles of CO 2 absorption, with a range of 0.15 to 0.17 mmol/g. Thus, these polyethylenimine-infiltered nanoporous polypropylene fibers can also be used in removing acidic gases from a gas mixture.

36 MATERIALS SCIENCE↗

Recovery of p -Hydroxybenzoic Acid from Cu-Catalyzed Alkaline Hydrogen Peroxide Pretreatment of Hybrid Poplar

p-Hydroxybenzoic acid (pHBA) is present in some hardwood biomass feedstocks as an ester attached to the polymeric lignin subunits. Here, we report the isolation and recovery of pHBA from alkaline liquor waste streams obtained from fractionation of hybrid poplar using the “Cu-AHP process”. This process features two stages: alkaline pre-extraction (AP) of the biomass and copper-catalyzed alkaline hydrogen peroxide pretreatment. On a biomass scale of 100 g, 0.5 g of pHBA with a purity of 96% was obtained after decolorization and crystallization. The scalability of the purification process was demonstrated by using liquor obtained from the first-stage AP with 900 g of poplar biomass to afford 3.5 g of crystalline pHBA with 97% purity. Altogether, these results show that pHBA may be isolated and purified from waste streams generated in the two-stage Cu-AHP process without any alteration of the process conditions or impact on carbohydrate and lignin fractionation.

09 BIOMASS FUELS↗

Unveiling Feedstock Variability: Insights into Corn Stover Conversion - Part I: Physicochemical Properties and Self-Degradation

Transforming agricultural waste into biofuels and bioproducts is crucial to advancing a low-carbon bioeconomy. However, the inherent variability in the composition and quality introduces uncertainties in the conversion efficiency and poses challenges in process development. Through integrating a high-throughput conversion system, material characterization techniques, and advanced data analysis tools, this study investigates the variability of corn stover and its subsequent impacts on carbohydrate conversion. The findings reveal that indoor storage substantially reduces the moisture and ash content and soil contamination, while other properties remain largely unchanged. Self-degradation due to microbial activity during storage decreases the carbohydrate content of corn stover but enhances glucose and xylose yields. A negative correlation is observed between sugar yields and lignin content across samples with varying ash and moisture content. The inhibitory effect of lignin diminishes in self-degraded samples likely due to the disrupted cell wall structure. Although self-degradation slightly increases cellulose crystallinity, no strong correlation was observed between the crystallinity and sugar yield. Hot water pretreatment under mild conditions effectively mitigates inherent variability, consistently improving the sugar yield from corn stover by up to 50%. By elucidating the feedstock variability and its impact on convertibility, these findings offer valuable insights into appropriate feedstock handling and management, highlighting potential strategies to address variability challenges.

09 BIOMASS FUELS↗

High-Performance Graphene Oxide Nanofiltration Membranes for Black Liquor Concentration

Black liquor (BL) concentration by multieffect evaporation is an extremely energy-intensive operation in the kraft pulping cycle. Membranes can significantly save energy in this process, but conventional membranes are strongly challenged by low solute rejections and poor stability in BL, which is a complex mixture containing dissolved lignin, other nonlignin organics, multiple inorganic salts at highly alkaline pH, and process temperatures of 70–85 °C. Here we describe in detail the fabrication, modification, and characterization of robust and high-performance graphene oxide (GO) nanofiltration membranes for BL concentration. We show that poly(ether sulfone) (PES)-supported GO membranes prepared from chemically reduced GO, and then subjected to high-pressure hydraulic compaction, show excellent chemical and mechanical stability under real BL conditions in comparison to conventional GO membranes. These membranes (referred to as “GO-3” in this work) show near-perfect (>99%) lignin rejection, high total organic carbon (TOC) rejection (up to 93%), and greatly improved inorganic rejections especially for divalent anions that are predominant in BL. Finally, the GO-3 membranes are scaled up on larger PES sheets (~660 cm2 in size) and are operated under realistic cross-flow conditions with real BL feed flow rates as high as 10 L/min at 70 °C. The GO-3 membranes show robust performance over more than 1500 h (60 days) of continuous operation in multiple cycles of 10–50 bar transmembrane pressures, attaining stable and sustained permeate fluxes as high as 25 LMH and excellent rejection performance equal to that obtained at smaller scale. The main results of this work have strong implications on the development of membrane processes for BL dewatering and more generally for processing of complex biorefinery feed streams.

Chemistry↗

An Improved CRISPR Interference Tool to Engineer Rhodococcus opacus

Rhodococcus opacus is a non-model bacterium that is well suited for valorizing lignin. Despite recent advances in our systems-level understanding of its versatile metabolism, studies of its gene functions at a single gene level are still lagging. Elucidating gene functions in non-model organisms is challenging due to limited genetic engineering tools that are convenient to use. To address this issue, we developed a simple gene repression system based on CRISPR interference (CRISPRi). This gene repression system uses a T 7 RNA polymerase system to express a small guide RNA, demonstrating improved repression compared to the previously demonstrated CRISPRi system (i.e., the maximum repression efficiency improved from 58% to 85%). Additionally, our cloning strategy allows for building multiple CRISPRi plasmids in parallel without any PCR step, facilitating the engineering of this GC-rich organism. Using the improved CRISPRi system, we confirmed the annotated roles of four metabolic pathway genes, which had been identified by our previous transcriptomic analysis to be related to the consumption of benzoate, vanillate, catechol, and acetate. Furthermore, we showed our tool’s utility by demonstrating the inducible accumulation of muconate that is a precursor of adipic acid, an important monomer for nylon production. While the maximum muconate yield obtained using our tool was 30% of the yield obtained using gene knockout, our tool showed its inducibility and partial repressibility. In conclusion, our CRISPRi tool will be useful to facilitate functional studies of this non-model organism and engineer this promising microbial chassis for lignin valorization.

09 BIOMASS FUELS↗

Refine your search to explore more results.