Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELASTIC PROPERTY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

Irradiation Behavior of Piezoelectric Materials for Nuclear Reactor Sensors

In-situ measurement of surface acoustic wave (SAW) resonators were used to characterize piezoelectric materials behavior in a nuclear reactor environment. Lithium niobate and aluminum nitride devices were tested up to 500°C temperature and 450 kW reactor power (1.9x10 12 n/cm 2 s). The resonant frequency responds to step changes in temperature and power. Materials’ response are inferred from the observed resonant frequency changes, in particular the kinetic behavior is used to determine mechanisms responsible for observed changes. The observed response is attributed to two mechanisms: temperature increase from gamma heating and accumulation of radiation-induced defects. Both of these mechanisms alter the physical properties of the piezoelectric materials, particularly the elastic constants. The demonstrated repeatability and reliability of SAW devices are attractive for sensor applications in extreme environments.

36 MATERIALS SCIENCE↗

Shock Hugoniot of Forged and Additively Manufactured 304L Stainless Steel

The purpose of this research was to measure the equation of state for additively manufactured (AM) and forged 304L stainless steel using a novel experimental technique. An understanding of the dynamic behavior of AM metals is integral to their timely adoption into various applications. The Hugoniot of the AM 304L was compared to that of the forged 304L at particle velocities where the material retains a two-wave structure. This comparison enabled us to determine the sensitivity of the equation of state to microstructure as varied due to processing. Our results showed that there was a measurable difference in the measured shock velocity between the AM and forged 304L. The shock wave velocities for the AM 304L were found to be ~3% slower than those for the forged 304L at similar particle velocities. To understand these differences, properties such as densities, sound speeds, and texture were measured and compared between the forged and AM materials. Our results showed that no measurable difference was found in these properties. Additionally, it is possible that differing elastic wave amplitudes may influence shock velocity.

36 MATERIALS SCIENCE↗

Analysis of legged landers for the survivable soft landing of instrument payloads.

Two methods of analysis have been developed for legged planetary landers. The first of these, the Large Displacement Gear Analysis, is a design tool for statically determining the large displacement stroking behavior, energy absorption characteristics, and internal load distributions in a single gear. The second, the Landing Dynamics Analysis, predicts the spatial landing dynamics of a legged lander. Effects of structural flexibility, elastic-plastic gear load characteristics, and soil properties on the loads, motions, and stability of the lander may be determined. Validation of the analytical techniques is accomplished through comparison of predicted results and experimental data obtained during a model test program.

Laurenson, R. M.↗

Application of the Collision-Imparted Velocity Method for Analyzing the Responses of Containment and Deflector Structures to Engine Rotor Fragment Impact

An approximate analysis, termed the Collision Imparted Velocity Method (CIVM), was employed for predicting the transient structural responses of containment rings or deflector rings which are subjected to impact from turbojet-engine rotor burst fragments. These 2-d structural rings may be initially circular or arbitrarily curved and may have either uniform or variable thickness; elastic, strain hardening, and strain rate material properties are accommodated. This approximate analysis utilizes kinetic energy and momentum conservation relations in order to predict the after-impact velocities of the fragment and the impacted ring segment. This information is then used in conjunction with a finite element structural response computation code to predict the transient, large deflection responses of the ring. Similarly, the equations of motion for each fragment are solved in small steps in time. Also, some comparisons of predictions with experimental data for fragment-impacted free containment rings are presented.

Collins, T. P.↗

Rotation in vibration, optimization, and aeroelastic stability problems

The effects of rotation in the areas of vibrations, dynamic stability, optimization, and aeroelasticity were studied. The governing equations of motion for the study of vibration and dynamic stability of a rapidly rotating deformable body were developed starting from the nonlinear theory of elasticity. Some common features such as the limitations of the classical theory of elasticity, the choice of axis system, the property of self-adjointness, the phenomenon of frequency splitting, shortcomings of stability methods as applied to gyroscopic systems, and the effect of internal and external damping on stability in gyroscopic systems are identified and discussed, and are then applied to three specific problems.

Kaza, K. R. V.↗

Nonlinear equations of motion for the elastic bending and torsion of twisted nonuniform rotor blades

The equations of motion are developed by two complementary methods, Hamilton's principle and the Newtonian method. The resulting equations are valid to second order for long, straight, slender, homogeneous, isotropic beams undergoing moderate displacements. The ordering scheme is based on the restriction that squares of the bending slopes, the torsion deformation, and the chord/radius and thickness/radius ratios are negligible with respect to unity. All remaining nonlinear terms are retained. The equations are valid for beams with mass centroid axis and area centroid (tension) axis offsets from the elastic axis, nonuniform mass and stiffness section properties, variable pretwist, and a small precone angle. The strain-displacement relations are developed from an exact transformation between the deformed and undeformed coordinate systems. These nonlinear relations form an important contribution to the final equations. Several nonlinear structural and inertial terms in the final equations are identified that can substantially influence the aeroelastic stability and response of hingeless helicopter rotor blades.

Hodges, D. H.↗

Development and demonstration of manufacturing processes for fabricating graphite/Larc-160 polyimide structural elements, part 4, paragraph B

Progress in the development of processes for production of Celion/LARC-160 graphite-polyimide materials, quality control, and the fabrication of Space Shuttle composite structure components is reported. Liquid chromatographic analyses of three repeatibility batches were performed and are compared to previous Hexcel standard production and to variables study LARC-160 intermediate resins. Development of processes for chopped fiber molding are described and flexural strength, elastic modulus, and other physical and mechanical properties of the molding are presented.

Source record↗

Traction behavior of two traction lubricants

In the analysis of rolling-sliding concentrated contacts, such as gears, bearings and traction drives, the traction characteristics of the lubricant are of prime importance. The elastic shear modulus and limiting shear stress properties of the lubricant dictate the traction/slip characteristics and power loss associated with an EHD contact undergoing slip and/or spin. These properties can be deducted directly from the initial slope m and maximum traction coefficient micron of an experimental traction curve. In this investigation, correlation equations are presented to predict m and micron for two modern traction fluids based on the regression analysis of 334 separate traction disk machine experiments. The effects of contact pressure, temperature, surface velocity, ellipticity ratio are examined. Problems in deducing lubricant shear moduli from disk machine tests are discussed.

Loewenthal, S. H.↗

Elastic model of the traction behavior of two traction lubricants

In the analysis of rolling-sliding concentrated contacts, such as gears, bearings and traction drives, the traction characteristics of the lubricant are of prime importance. The elastic shear modulus and limiting shear stress properties of the lubricant dictate the traction/slip characteristics and power loss associated with an EHD contact undergoing slip and/or spin. These properties can be deducted directly from the initial slope m and maximum traction coefficient micron of an experimental traction curve. In this investigation, correlation equations are presented to predict m and micron for two modern traction fluids based on the regression analysis of 334 separate traction disk machine experiments. The effects of contact pressure, temperature, surface velocity, ellipticity ratio are examined. Problems in deducing lubricant shear moduli from disk machine tests are discussed. Previously announced in STAR as N83-20116

Loewenthal, S. H.↗

Off-axis tensile properties and fracture in a unidirectional graphite/polyimide composite (Celion 6000/PMR 15)

Tensile properties of unidirectional Celion 6000 graphite/PMR 15 polyimide composites prepared by hot molding and cold molding processes were measured at room temperature and 316 C, the upper use temperature of the polyimide resin, at both 45 and 90 deg to the fiber axis. The resulting fractures were characterized by scanning electron microscopy and materialographic techniques. Variation in tensile properties with processing history occurred in the elastic modulus and strain to failure for specimens loaded at 90 deg at 316 C, and in the fracture stress, and hence the in-plane shear stress, for those loaded at 45 deg at room temperature. Significant plastic deformation was observed in the 45 deg orientation at 316 C for material produced by both processing methods. In general, fracture occurred by both failure within the matrix and at the fiber-matrix interface; the degree of interfacial failure increased with temperature. Secondary cracking below the primary fracture surface was also observed.

Harper, J.↗

The effects of molecular weight on the single lap shear creep and constant strain rate behavior of thermoplastic polyimidesulfone adhesive

The bonded shear creep and constant strain rate behaviors of zero, one, and three percent endcapped thermoplastic polyimidesulfone adhesive were examined at room and elevated temperatures. Endcapping was accomplished by the addition of phthalic anhydrides. The primary objective was to determine the effects of molecular weight on the mechanical properties of the adhesive. Viscoelastic and nonlinear elastic constitutive equations were utilized to model the adhesive. Ludwik's and Crochet's relations were used to describe the experimental failure data. The effects of molecular weight changes on the above mentioned mechanical behavior were assessed. The viscoelastic Chase-Goldsmith and elastic nonlinear relations gave a good fit to the experimental stress strain behavior. Crochet's relations based on Maxwell and Chase-Goldsmith models were fit to delayed failure data. Ludwik's equations revealed negligible rate dependence. Ultimate stress levels and the safe levels for creep stresses were found to decrease as molecular weight was reduced.

Dembosky, Stanley K.↗

Static and dynamic properties of incommensurate smectic-A(IC) liquid crystals

The elasticity, topological defects, and hydrodynamics of the incommensurate smectic A(IC) phase liquid crystals are studied. The phase is characterized by two colinear mass density waves of incommensurate spatial frequency. The elastic free energy is formulated in terms of a displacement field and a phason field. It is found that the topological defects of the system are dislocations with a nonzero phason field and phason field components. A two-dimensional Burgers lattice for these dislocations is introduced. It is shown that the hydrodynamic modes of the phase include first- and second-sound modes whose direction-dependent velocities are identical to those in ordinary smectics.

Lubensky, T. C.↗

Recent results concerning the stability of viscoelastic shear deformable plates under compressive edge loading

Some recent results obtained by the authors are summarized concerning the stability of transversely isotropic flat panels whose materials exhibit a viscoelastic behavior and whose edges are subjected to in-plane biaxial compressive loads. Two transversely isotropic type materials, largely used in advanced technology, are considered: (1) the pyrolytic-graphite type, used in the thermal protection of aerospace vehicles, and (2) the type corresponding to unidirectional fiber-reinforced composites. In the former case, the planes of isotropy are parallel at each point to the midplane of the plate. In the latter case, they are normal to the fiber directions. The micromechanical relations developed by Aboudi (1984, 1986, 1987) are considered in conjunction with the correspondence principle of linear viscoelastic theory in order to predict the macroscopic viscoelastic properties of a material composed of uniaxial elastic fibers embedded in a linear viscoelastic matrix.

Librescu, L.↗

High-toughness graphite/epoxy composite material experiment

This LDEF experiment was designed to measure the effects of near-earth exposure on graphite/epoxy composites over a range of properties. All of the specimens were 8 plies thick, with one of two different cross-ply angles and with one of four different values of bonding fraction between plies. The mechanical properties of interest are toughness, strength, and elastic modulus. Six toughness specimens and nine strength/modulus specimens were manufactured and flown.

Felbeck, David K.↗

Graphite Fiber/Copper Matrix Composites for Space Power Heat Pipe Fin Applications

High specific thermal conductivity (thermal conductivity divided by density) is a major design criterion for minimizing system mass for space power systems. For nuclear source power systems, graphite fiber reinforced copper matrix (Gr/Cu) composites offer good potential as a radiator fin material operating at service temperatures above 500 K. Specific thermal conductivity in the longitudinal direction is better than beryllium and almost twice that of copper. The high specific thermal conductivity of Gr/Cu offers the potential of reducing radiator mass by as much as 30 percent. Gr/Cu composites also offer the designer a range of available properties for various missions and applications. The properties of Gr/Cu are highly anisotropic. Longitudinal elastic modulus is comparable to beryllium and about three times that of copper. Thermal expansion in the longitudinal direction is near zero, while it exceeds that of copper in the transverse direction.

McDanels, David L.↗

Micromechanical modeling of laminated composites with interfaces and woven composites using the boundary element method

The boundary element method is utilized to analyze the effects of fiber/matrix interfaces on the micromechanical behavior of laminated composites as well as the elastic behavior of woven composites. Effective composite properties are computed for laminated SiC/RBSN and SiC/Ti-15-3 composites, as well as a woven SiC/SiC composite. The properties calculated using the computerized tool BEST-CMS match the experimental results well.

Goldberg, Robert K.↗

Refine your search to explore more results.