Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dislocation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Multiscale mechanical fatigue damage of stainless steel investigated by neutron diffraction and X-ray microdiffraction

Mechanical fatigue behavior of AL6XN stainless steel as a typical type of planar slip alloy was investigated by in situ neutron diffraction and synchrotron-based X-ray microdiffraction methods. Under cyclic loading at a high strain amplitude (+/- 0.8%), the fatigue damage originated mainly from the accumulation of statistical stored dislocations, as clearly evidenced from a continuous increase in diffraction peak width with increasing the number of load cycles. However, under cyclic loading at a low strain amplitude (+/- 0.3%), the density of statistical stored dislocations became saturated just after a hundred loading cycles and the fatigue damage was mainly dominated by the accumulation of persistent [Alders bands (PLBs) and the complex interactions among various PLBs as evidenced through X-ray microdiffraction measurements. It was further found that there exists obvious grain-orientation-dependent local damage in the low-strain-amplitude fatigued sample. In particular, fatigued grains orientated with [001] paralleling the loading direction are subjected to compressive stress and contain a large number of broad PLBs in boundaries arraying the edge dislocation pile-ups, which generate a large stress gradient leading to local plastic instability. As a result, the highly localized stress field at PLBs in the cyclically-deformed sample at a low strain amplitude may explain the obvious cyclic stress softening.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Response of 14YWT alloys under neutron irradiation: A complementary study on microstructure and mechanical properties

Nanostructured ferritic alloys (NFAs) having sub-micron grain size with a high density of nano-oxides (NOs) (size of ~2-3 nm) are one of the best candidates for structural components in Generation IV nuclear systems. In this study, 14YWT NFA cladding tubes were irradiated in BOR60 reactor up to 7 dpa at 360-370 °C. Detailed microstructural analysis has been conducted using bright field transmission electron microscopy, bright field scanning transmission electron microscopy, energy filtered transmission electron microscopy, energy dispersive X-ray spectroscopy, electron energy loss spectroscopy and transmission Kikuchi diffraction techniques. This revealed cavities, <100> and <111> type dislocation loops, and α' precipitates forming after irradiation with relationships between cavities and NOs, and α' precipitates and NOs. Cavities mostly form on the NOs; whereas, α' precipitates form between the NOs where the point defect concentration is high. Moreover, α' precipitates are distributed homogenously on and around the dislocation loops which is consistent with the observation that there is no Cr segregation on dislocation loops. Grain boundaries were found to be mostly depleted in Cr; however, the characteristics of each grain boundary determines the Cr behavior and the α' denuded zone around the grain boundaries. Mechanical properties of the irradiated tubes have been determined by using both low force and high force nanoindentation techniques, resulting in 1.03±0.33 GPa and 0.82±0.20 GPa hardening, respectively. Dispersed barrier hardening calculations and nanoindentation measurements are in good agreement. In this paper, 14YWT NFA has been systematically studied after neutron irradiation to better understand its superior performance: low α' concentration, low swelling and low radiation-induced hardening.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Structural damage and phase stability of Al 0.3 CoCrFeNi high entropy alloy under high temperature ion irradiation

In this study, an initially single phase high entropy alloy (HEA) Al 0.3 CoCrFeNi was irradiated by 3 MeV Au ions to a fluence of 6 × 10 15 cm –2 (~31 dpa at damage peak) at four different temperatures ranging from 250 °C to 650 °C. Transmission electron microscopy (TEM) and Atom probe tomography (APT) were employed to study the evolution of structural damage and phase stability with irradiation temperature. Al 0.3 CoCrFeNi exhibited a similar evolution of irradiation-induced defects with temperature as compared with conventional FCC alloys. At 250 °C and 350 °C, most of the visible irradiation-induced defects were faulted 1/3$\langle{111}\rangle$ dislocation loops. As the irradiation temperature increased to 500 °C, perfect 1/2$\langle{110}\rangle$ dislocation loops were observed along with the faulted loops. At the highest irradiation temperature 650 °C, only dislocation lines and networks could be observed. Regarding phase stability, the 3 MeV Au irradiation was observed to suppress the precipitation of (Ni, Al)-enriched nano clusters and the L12 ordered structure at irradiation temperatures 250 °C to 500 °C whereas precipitation of the B2 ordered structure was accelerated at 650 °C. This resulted in qualitatively opposite precipitation behavior between the ion irradiated damage region and unirradiated region at 500 °C and 650 °C. The opposite phase stability of the ion-irradiated damage region and unirradiated region at different temperatures is attributed to the competing effects of ballistic dissolution vs irradiation enhanced diffusion on precipitation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In-situ synchrotron X-ray micro-diffraction investigation of ultra-low-strain deformation microstructure in laminated Ti-Al composites

An ultra-low-strain deformation microstructure was revealed for the first time non-destructively in the bulk interior of an annealed laminated Ti-Al composite-in the "fully recrystallized" Al layer-by a synchrotron-based micro-diffraction technique, namely differential aperture X-ray microscopy (DAXM), through real space mapping with a very high angular resolution (0.01 degrees). This ultra-low-strain deformation microstructure was found to result from the thermal stress, induced during cooling after annealing, due to the different coefficients of thermal expansion for the Ti and Al layers. The annealed sample was further tensile deformed to a strain of 1.66% and followed by in situ DAXM and analyzed by various misorientation mapping methods. The results pointed to the important effects of the initial microstructure and the interface constraint, as well as the grain size and crystal orientation, on the plastic deformation. A gradient in dislocation density from the layer interface to the center was found in the Al layer of the annealed sample, and this gradient increased slightly during tensile deformation. The variation of the dislocation density was further discussed based on the activation and interaction of dislocations in grains of different sizes and orientations during plastic deformation. The findings of this study provided valuable insights in understanding the constraint effect of the laminated metal composite and the design of novel composite materials. (c) 2020 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Crystallographic orientation↗
DOE OSTI2020

Investigating the compressive strength and strain localization of nanotwinned nickel alloys

Sputter deposited nickel-molybdenum-tungsten (Ni-Mo-W) thin films possess a beneficial suite of properties that stem from the extremely fine growth twins that form during the deposition process. Previously these materi- als were only characterized in tension, however, in this study in situ micropillar compression and post-mortem microstructural analysis of nanotwinned Ni 84 Mo 11 W 5 micropillars were employed to measure the compressive response and elucidate the attendant deformation mechanisms. The pillars exhibit Hookean behavior to com- pressive strengths of 3-3.5 GPa and the onset of non-linear plastic flow was manifest by discrete strain bursts and highly localized shear bands. Plastic deformation was concentrated at the top of the pillar, while the bulk of the micropillar was nominally unaffected. Post-mortem investigations indicate that at sufficiently high stresses shear banding is triggered, resulting in intense and highly localized plastic deformation that led to the formation of twin-free nanocrystalline grains within highly deformed shear bands. By contrast, the regions adjacent to the shear bands were unaffected. The absence of detwinning and dislocation glide mechanisms was unexpected and in direct contrast to what has been observed in nanotwinned Cu-Al. Post-mortem observations of the Ni-Mo-W micropillars suggest that the ultrafine twins create a unique form of dislocation starvation and source-limited plasticity. The ultrahigh compressive strength is governed by the triggering of shear bands rather than the activa- tion of dislocation glide. Finally, the specialized nature of plasticity in nanotwinned Ni-Mo-W is clear, even though the precise trigger for shear band formation in nanotwinned Ni-Mo-W remains to be identified.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Characteristics and mechanisms of hydrogen-induced quasi-cleavage fracture of lath martensitic steel

Here this study presents an in-depth characterization of the microstructures, crystallographic orientations, and dislocation characteristics beneath hydrogen-induced quasi-cleavage fracture features of an as-quenched, lath martensitic (α') 22MnB5 steel. The fracture surfaces of gaseous hydrogen-embrittled martensitic specimens were analyzed by a combination of multiple analytical tools: scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), transmission electron microscopy (TEM), and transmission Kikuchi diffraction (TKD). The dominant fracture mode in the hydrogen-affected zones was quasi-cleavage fracture, which involved significant plasticity, evidenced by plastic zones near tear ridges and a high density of dislocations beneath the quasi-cleavage facets. The martensite constituent sizes, variant orientations, and boundaries influenced the quasi-cleavage surface morphologies. Fractography revealed the occurrence of {100} α' -type cleavage across martensitic laths, developing relatively “flat” quasi-cleavage surfaces, in addition to {110} α' -type cracking likely along lath and block boundaries, and fracture along non-cleavage planes. The likelihood of the formation of the relatively “flat” quasi-cleavage surfaces increased with increasing martensitic constituent sizes. Substantial dislocation bands formed on intersecting {112} α' slip planes within a martensite block below the hydrogen-induced cleavage fractures on {100} α' planes. River markings on the quasi-cleavage surfaces were found to originate from the complex, hierarchical lath martensitic microstructure. Steps and ridges on the quasi-cleavage facets generally linked with the various martensitic boundaries, suggesting that they were produced as a result of crack deviations at those boundaries. The fracture paths and martensite quasi-cleavage mechanisms are discussed in the context of the role of hydrogen and Cottrell cleavage model.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Atomic structures of interfacial solute gateways to θ' precipitates in Al-Cu alloys

Many materials employed in critical structural applications depend upon metastable strengthening precipitates that transform or dissolve at elevated temperatures. Herein, aberration-corrected scanning transmission electron microscopy and first-principles calculations are used to accurately determine the atomic structure of the highly mobile, semi-coherent precipitate interfaces that control this process in the classic θ' (Al 2 Cu) precipitate in the Al-Cu system. Semi-coherent {110} interfaces are found to be composed of an array of unexpected misfit dislocations that are arranged in two different structural units. Dislocations accommodate nearly all of the misfit between the Al matrix and strengthening phase. Cu is observed to segregate to the compressed edge of the dislocation cores at specific sites in this interface. First-principles calculations revealed the energetic landscape that facilitates these sites to become entry and exit gateways of Cu atoms in this semi-coherent interface. In conclusion, this investigation reveals critical features within semi-coherent interfaces that determine the thermal stability of precipitation-hardened alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Columnar Grain-driven Plasticity and Cracking in Nanotwinned FCC Metals

The mechanisms of strengthening and plasticity in columnar-grained metals with preferentially oriented nano-sized twins have been examined traditionally by considering dislocation processes, but rarely from the perspective of grain boundary (GB) deformation. Here, the effects of GB strain accommodation on plastic deformation in four different columnar-grained nanocrystalline nanotwinned (nt) face-centered-cubic metals (Cu, Ag, Al, and Ni) were studied by large-scale molecular dynamics simulations. It is observed that in tensile deformation parallel to coherent twin boundaries (CTBs), the dislocation mechanisms in each metal are identical and associated with GB emissions of jog and threading dislocations at small and large CTB spacings, respectively. However, CTB strengthening effects are increasingly more pronounced in columnar-grained nt metals as their shear modulus increases, which is rationalized by the dependence of GB stress concentrations on twin size, metal type and strain rate. Also, while flow stresses in nt-Cu, nt-Ag, and nt-Al metals increase linearly with decreasing CTB spacing, a maximum strength limit is reached in nt-Ni below a critical CTB spacing of 6 nm. The strength limit in nt-Ni results from columnar GB cracking induced by prominent GB sliding. For columnar-grained microstructures, GB sliding is equivalent in nt-Ag and nt-Al and slightly lower in nt-Cu but markedly higher in nt-Ni. These findings underscore the importance of new GB deformation mechanisms on plasticity and fracture in columnar-grained nt metals and enrich our understanding of CTB strengthening in fcc metals synthesized in the literature.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The effect of microstructure on the dynamic shock response of 1045 steel

Herein, the effect of microstructure on the shock response of 1045 steel is investigated via plate impact experiments and postmortem characterization. Three unique microstructures are explored: ferrite-pearlite, martensite, and ferrite with spheroidal cementite (i.e. spheroidized). Two spall recovery experiments, at approximate peak pressures of 3.2 and 3.5 GPa, are conducted to assess the Hugoniot elastic limit (HEL), spall strength, and damage morphology of the various microstructures. The ferrite-pearlite and martensite microstructures exhibit continuous yielding at both quasi-static and dynamic rates, while the spheroidized condition displays discontinuous yielding. Discontinuous yielding of the spheroidized microstructure is attributed to a combined low initial dislocation density coupled with a low dislocation nucleation rate. The spall strength of ferrite-pearlite is consistently lower than the spheroidized microstructure, attributed to elongated cementite that is more susceptible to cracking than more spherical cementite precipitates. Despite a high density of boundaries, martensite exhibits the highest spall strength. A large percentage of the boundaries within the martensite microstructure are found to be low energy (i.e. Σ3 or low angle), and are thus less susceptible to spall damage. Overall, the high spall strength of martensite is likely linked to traditional strengthening mechanisms that limit dislocation motion.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Deformation mechanisms in an additively manufactured dual-phase eutectic high-entropy alloy

Nanostructured metals and alloys often exhibit high strengths but at the expense of reduced ductility. Through harnessing the far-from-equilibrium processing conditions of laser powder-bed fusion (L-PBF) additive manufacturing, we develop a dual-phase nanolamellar structure comprised of FCC/L1 2 and BCC/B2 phases in a Ni 40 Co 20 Fe 10 Cr 10 Al 18 W 2 eutectic high-entropy alloy (EHEA), which exhibits a combination of ultrahigh yield strength (>1.4 GPa) and large tensile ductility (~17%). The deformation mechanisms of the additively manufactured EHEA are studied via in-situ synchrotron X-ray diffraction and high-resolution transmission electron microscopy. The high yield strength mainly results from effective blockage of dislocation motion by the high density of lamellar interfaces. The refined nanolamellar structures and low stacking fault energy (SFE) promote stacking fault (SF)-mediated deformation in FCC/L1 2 nanolamellae. The accumulation of abundant dislocations and SFs at lamellar interfaces can effectively elevate local stresses to promote dislocation multiplication and martensitic transformation in BCC/B2 nanolamellae. The cooperative deformation of the dual phases, assisted by the semi-coherent lamellar interfaces, gives rise to the large ductility of the as-printed EHEA. In addition, here we also demonstrate that post-printing heat treatment allows us to tune the non-equilibrium microstructures and deformation mechanisms. After annealing, the significantly reduced SFE and thicknesses of the FCC nanolamellae facilitate the formation of massive SFs. The dissolution of nano-precipitates in the BCC/B2 nanolamellae reduces spatial confinement and further promotes martensitic transformation to enhance work hardening. Our work provides fundamental insights into the rich variety of deformation mechanisms underlying the exceptional mechanical properties of the additively manufactured dual-phase nanolamellar EHEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Critical operating stress of persistent slip bands in Cu

This work elucidates the dependence of operating stress of persistent slip bands (PSB) on the channel width and wall dislocation density. Using Cu as a model system and molecular dynamics as the main investigative tool, a new length scale effect, namely the wall dislocation spacing, is provided to enhance theoretical understanding of PSBs. It is discovered that the operation of PSB is a thermally activated event in which operating stress is inversely related to the wall dislocation spacing, strain rate and temperature. Leveraging the existing framework of confined layer slip in nanoscale metallic multilayers and classical nucleation theory, a mathematical model describing the rate- and temperature- dependent PSB operating stress is here proposed.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A new self-adaptive reconstruction method to identify defects through Wigner–Seitz approach

A new self-adaptive reconstruction method based on local atomic structure at any given molecular dynamics (MD) step has been developed in this article. The method can be used in Wigner–Seitz defect analysis approach to correctly and efficiently explore the information of both point defects and complex defect clusters (e.g. dislocation loops and voids) formed after a displacement cascade where the cascade interacts with grain boundaries and/or dislocations. The algorithm and validation are provided in detail. Results for identification of radiation defects during and after cascades interacting with a dislocation network show that the new method can well recognize all simple and complex defects and defect clusters. Thus, this new method provides a totally new way to explore the density and size of radiation defects at atomic scale after complex MD evolution processes, providing correct information to understand and predict radiation damage in materials through atomic simulations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2018

Mechanism-based modeling of solute strengthening: Application to thermal creep in Zr alloy

In this paper, a crystallographic thermal creep model is proposed for Zr alloys that accounts for the hardening contribution of solutes via their time-dependent pinning effect on dislocations. The core-diffusion model proposed by Soare and Curtin (2008a) is coupled with a recently proposed constitutive modeling framework (Wang et al., 2017, 2016) accounting for the heterogeneous distribution of internal stresses within grains. The Coble creep mechanism is also included. This model is, in turn, embedded in the effective medium crystallographic VPSC framework and used to predict creep strain evolution of polycrystals under different temperature and stress conditions. The simulation results reproduce the experimental creep data for Zircaloy-4 and the transition between the low (n~1), intermediate (n~4) and high (n~9) power law creep regimes. This is achieved through the dependence on local aging time of the solute-dislocation binding energy. The anomalies in strain rate sensitivity (SRS) are discussed in terms of core-diffusion effects on dislocation junction strength. The mechanism-based model captures the primary and secondary creep regimes results reported by Kombaiah and Murty (2015a, 2015b) for a comprehensive set of testing conditions covering the 500–600 °C interval, stresses spanning 14–156 MPa, and steady state creep rates varying between 1.5·10 -9 s -1 to 2·10 -3 s -1 . There are two major advantages to this model with respect to more empirical ones used as constitutive laws for describing thermal creep of cladding: 1) specific dependences on the nature of solutes and their concentrations are explicitly accounted for; 2) accident conditions in reactors, such as RIA and LOCA, usually take place in short times, and deformation takes place in the primary, not the steady-state creep stage. Finally, as a consequence, a model that accounts for the evolution with time of microstructure is more reliable for this kind of simulation.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Characterization of localized plastic deformation behaviors associated with dynamic strain aging in pipeline steels using digital image correlation

Localized deformation behavior in X52 and X70 pipeline steels during dynamic strain aging (or DSA, caused by interstitial atom-dislocation interactions during plastic deformation) were systematically assessed using digital image correlation with incremental strain analysis during elevated temperature tensile testing in the range of 25-350 °C. Similar to materials that use substitutional atoms for DSA, deformation band propagation and nucleation behaviors in the steels were directly related to the morphologies of flow curves from the tensile data. Comparisons between the steels and substitutional DSA systems were made. The type of localized deformation behavior was dependent on the temperature and strain rate conditions of the tensile test and the total amount of strain in the sample. Plastic flow was primarily dominated by deformation band propagation and nucleation at relatively low and high temperatures respectively within the DSA regime. It was theorized that the changing serration morphologies and deformation behaviors at different temperature-strain rate conditions were due to relative differences between the mobility of the solute atoms and the velocity of the mobile dislocations throughout the DSA regime. The dislocation density (which increases due to strain hardening during a tensile test) also influenced deformation behavior at relatively low and high strains.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructure-sensitive modeling of high temperature creep in grade-91 alloy

Predicting the effects of microstructure on high-temperature creep responses of steel components is critical to minimize the risks of failure and maximize economic viability in the energy sector. In this research, a recently developed advanced mechanistic constitutive model is employed to study the effect of microstructure on the creep responses and to rationalize experimentally reported variability in the performances of grade-91 alloy. Hundreds of experimental creep tests from the literature are used to assess the predictability of the model. The model proposed is shown to accurately predict the steady-state creep rates and also the less commonly considered, yet important, primary-to-secondary transients for a wide range of creep conditions. Further, the model is capable of extrapolating the creep response of grade 91 alloy even outside of the calibration regime. Using this model, the roles of initial microstructure described in terms of grain size, dislocation density, and precipitate content, on the creep responses are investigated. The effect of initial microstructure on the steady-state creep rates and creep-strain is found to vary with stress and temperature. Grain size plays a significant role in the low-stress creep, where the diffusional creep is dominant. On the other hand, the effects of dislocation densities and precipitate content are significant in the dislocation-plasticity-dominated high-stress and temperature regimes. Furthermore, by comparing model predictions against a large experimental creep database, it is found that variability in the creep responses can be rationalized on the basis of differences in the initial microstructure. Overall, this work provides a robust pathway for microstructure-aware engineering design, verification, and validation of metallic components for energy applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Bridging microscale to macroscale mechanical property measurements of FeCrAl alloys by crystal plasticity modeling

FeCrAl alloys are candidates for accident tolerant fuel cladding of light water reactors. In this work, a microstructure- and temperature-dependent crystal plasticity model is employed to bridge microscale to macroscale mechanical property measurements of FeCrAl alloys. With the visco-plastic self-consistent (VPSC) polycrystal plasticity framework, a mechanism-based single crystal plasticity (MSCP) model adopts the Arrhenius type rate equation to describe the dependence of the critical resolved shear stress for dislocation slips on their temperature-dependent intrinsic frictional resistance and the microstructure-dependent irradiation hardening. The intrinsic frictional resistance associated with {110}<111> and {112}<111> slip systems were measured by in-situ micromechanical testing on unirradiated/irradiated samples at 25-500 °C. The irradiation hardening is estimated by the Bacon-Kocks-Scattergood (BKS) model with density and size of radiation-induced defects measured from microstructural characterization. Several features associated with thermo-mechanical behavior of unirradiated/irradiated polycrystalline FeCrAl alloys are captured. High density of deformation-induced dislocations and radiation-induced defects results in obvious hardening at room temperature, which is weakened at high temperature, and facilitates damage evolution during deformation. Moreover, both high temperature and radiation-induced defects, which facilitate dislocation multiplication, trigger large hardening rate. Finally, the proposed method together with application of accelerator-based ion irradiation technique is a surrogate approach to simulate neutron damage, improving the efficiency associated with evaluation of mechanical properties of FeCrAl alloys exposed to temperature, stress and radiation conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In situ neutron diffraction study of fatigue behavior of CrFeCoNiMo 0.2 high entropy alloy

In situ neutron diffraction measurement was applied to study the low-cycle fatigue behavior of CrFeCoNiMo 0.2 high entropy alloy. A two-step stress-controlled fatigue test with a stress range of 100–460 and 20–500 MPa was employed. The as-cast sample was cycled 129,000 and 61,000 times, respectively, before fracture. The evolution of the lattice strain and peak intensity demonstrates that the main deformation mechanism is dislocation slip, while no evidence of stacking fault was found. A three-stage ratcheting was clearly observed. Under the stress-controlled mode, the experimentally determined dislocation density increases linearly with the ratcheting strain. Here, the increase of the dislocation density results in a decay of the ratcheting strain rate, which stabilizes the structure and is beneficial for fatigue resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Influence of trimethylaluminum predoses on the growth morphology, film-substrate interface, and microstructure of MOCVD-grown AlN on (1 1 1)Si

Aluminum nitride (AlN) was deposited on (1 1 1) silicon by metalorganic chemical vapor deposition after varied trimethylaluminum “predoses”. Growth morphologies, film-substrate interfaces, and film microstructures were examined using scanning electron microscopy, atomic force microscopy, X-ray diffraction, and transmission electron microscopy. In samples grown with predoses, lateral growth was observed over faceted “patches” formed during the predose. Three-dimensional growth was observed to seed from small islands on the surface of these patches and eventually overgrow them. The three-dimensional growth mode was similar to that observed when AlN was grown without a predose, resulting in similar morphologies in all films, regardless of predose, after the islands coalesced. The AlN-silicon interface was found to be predominantly amorphous when no predose was used. However, narrow regions were observed over which the film was in atomic registry with the substrate. This indicates AlN nucleates in epitaxy with the substrate and amorphous silicon nitride forms between nucleation sites due to ammonia exposure. Films grown with predoses had structurally abrupt interfaces, suggesting aluminum within the observed patch features inhibits the reaction between ammonia and silicon at the onset of growth. A structure distinct from both wurtzite AlN and diamond cubic silicon was observed at the substrate interface in films grown with a predose, consistent with either zinc blende AlN or a strained Si/Al alloy. A mosaic microstructure was observed in all films, grown with or without predoses, which consisted of sub-boundaries formed by clusters of threading dislocations. Finally, threading dislocations, separated by hundreds of nanometers, were found to be tilted along common directions, providing evidence for a dislocation bending mechanism possibly enhanced by the predose.

36 MATERIALS SCIENCE↗

Refine your search to explore more results.