Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Code Validation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

Draft Rules for Alloy 617 Creep-Fatigue Design Using an EPP+SMT Approach

The report describes an improved new creep-fatigue design method for structural components in high temperature nuclear service. The new method uses an integrated elastic-perfectly plastic (EPP) analysis and Simplified Model Test (SMT) approach that greatly simplifies the design process by avoiding the separate evaluation of creep and fatigue damages and eliminating the requirement of stress classification. The report includes draft design rules, presented in a format compatible with an ASME nuclear Code Case, as well as a commentary on the rules and the validation of the rules using pressurized SMT (p-SMT) test data. Areas of potential improvement have been identified for further evaluation. The report also develops EPP+SMT design charts for Alloy 617 at temperatures between 800°C and 950°C by extrapolating high strain range, short hold test data to low strain range and long hold times, typical for structural components in high temperature nuclear service. The design charts are currently limited to 10,000 cycles to avoid excessive extrapolation outside the test database. More robust alternate extrapolation procedures will be considered in future work. The report includes several verification problems comparing the new EPP+SMT design method with current ASME creep-fatigue design methods. The comparison demonstrates that the EPP+SMT method significantly reduces the over-conservatism in current methods. Finally, the report includes a fully-documented sample problem with multiple load cases detailing the application of proposed EPP+SMT design rules.

36 MATERIALS SCIENCE↗

Nuclear Software Validation for 7% Enriched UO 2 Fuel Lattices

This analysis performs validation for the Virtual Environment for Reaction Application’s (VERA’s) neutronics codes MPACT and Shift against measured data from the Seven Percent Critical Experiment (7uPCX) at Sandia National Laboratory. The benchmarking supports the future application of VERA for analysis of high-assay low-enriched uranium (HALEU) fuel in commercial pressurized water reactors (PWRs). VERA demonstrates very good agreement with measured data, and the deterministic code MPACT also agrees very well with higher-fidelity stochastic methods KENO-VI and Shift in both total neutron flux and fission rate distribution comparisons. Despite some significant differences between the 7uPCX and existing commercial PWRs that challenge the neutron cross section data and transport solver methods used by MPACT, all of the results are excellent. The agreement increases the confidence in the applicability and accuracy of VERA for reactor analysis of HALEU fuels in commercial reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of Transmission Measurements Capability at VISION Spectrometer [Slides]

This presentation covers the development of transmission measurements capability at VISION Spectrometer. Main takeaways include that INS and transmission measurements are and should be the most significant part of TSL validation, as they are the fundamental quantities used by Monte Carlo neutronics codes. Additionally, the development of transmission capability at VISION instrument has commenced. Promising first results have been obtained with a big impact by the use of the collimators. Finally, Areas of improvement have been identified and new measurements are planned for June.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Final Report for Center for Tokamak Transient Simulations at USU

Providing plasma fluid codes like NIMROD with continuum drift kinetic (CDK) physics that is quantitatively valid and computationally feasible throughout the spatial domain is difficult. Work at Utah State University (USU), in collaboration with the Center for Tokamak Transient Simulations (CTTS), focused on applying CDK closures in disruption-related calculations. Three examples where kinetic physics is paramount are (1) the electron stress tensor closure in Ohms law for accurately describing neoclassical tearing mode (NTM) evolution, (2) runaway electron (RE) density (nRE) and current (jRE) moments in NIMROD’s extended MHD model for self-consistent evolution of RE populations during disruptions and, (3) energetic ion effects on a myriad of MHD instabilities. While NTM simulations and continuum and PIC approaches to energetic ions in NIMROD have been a major goals of USU’s closure work for several years, the development of self-consistent CDK RE capability in NIMROD was started and extended considerably during the CTTS effort. Some goals of CDK RE in NIMROD are to explore the effects of the 2D relativistic phase space in 4D simulations and compare with NIMROD’s fluid RE model. Four publications and two PhD theses came out of the USU CTTS effort.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hygrothermal Material Properties for Soils in Building Science

Saving energy in buildings is top of mind with today s building professionals. Although designing energy-efficient walls and roofs is mostly a no-brainer, ensuring that below-grade foundations do not generate moisture problems has become even more complex, particularly because of how soil is involved. Hygrothermal performance of soils coupled to buildings is complicated because of the dearth of information on soil properties. A computational approach for heat transfer through the ground has been well-defined, and simplified methods have been developed. These approaches, however, generally ignore the transfer of soil moisture, which is not negligible. The intention of an ongoing study at Oak Ridge (TN) National Laboratory, therefore, is to gather, comprehend and adapt soil properties from soil science as well. The obtained information must be applicable to related tasks in building science and validated with hygrothermal calculation tools, where additional plugins to the existing software code WUFI (an acronym for Warme unde Felichte Instructionar, which translates to unsteady heat and moisture) are required. (See the sidebar, opposite page, for specifics on WUFI.)Simulation results from WUFI are being compared with existing thermal-only measurements and are being accomplished with ongoing hygrothermal measurements. The final outcome of the study will be the evaluation of several soil types in several climate zones for a number of basement assembly types. The study will define the type of soil, together with the type of building construction considered most and least reliable with respect to energy consumption and moisture safety. Furthermore, the study will determine the influences that different soils have on total energy loss through the ground.

Kehrer, Manfred↗

MCNP Progress & Performance Improvements

Twenty-eight slides give information about the work of the US DOE/NNSA Nuclear Criticality Safety Program on MCNP6 under the following headings: MCNP6.1.1 Release, with ENDF/B-VII.1; Verification/Validation; User Support & Training; Performance Improvements; and Work in Progress. Whisper methodology will be incorporated into the code, and run speed should be increased.

42 ENGINEERING↗

Review of Transient Testing of Fast Reactor Fuels in the Transient REActor Test Facility (TREAT)

The restart of the Transient REActor Test (TREAT) facility provides a unique opportunity to engage the fast reactor fuels community to reinitiate in-pile experimental safety studies. Historically, the TREAT facility played a critical role in characterizing the behavior of both metal and oxide fast reactor fuels under off-normal conditions, irradiating hundreds of fuel pins to support fast reactor fuel development programs. The resulting test data has provided validation for a multitude of fuel performance and severe accident analysis computer codes. This paper will provide a review of the historical database of TREAT experiments including experiment design, instrumentation, test objectives, and salient findings. Additionally, the paper will provide an introduction to the current and future experiment plans of the U.S. transient testing program at TREAT.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGR-5/6/7 Final Release-to-Birth Ratio Data Analysis

AGR-5/6/7 is the last of a series of Advanced Gas Reactor (AGR) experiments conducted in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) in support of development and qualification of tristructural isotropic (TRISO) low-enriched fuel for use in the high-temperature gas cooled reactor (HTGR). AGR configuration and irradiation conditions are based on prismatic HTGR technology that is distinguished primarily through the use of helium coolant, a low-power-density ceramic core capable of withstanding very high temperatures, and TRISO-coated particle fuel. The AGR tests provide valuable irradiation-performance data to support fuel process development, qualify fuel for normal operation and accident conditions, and support development and validation of fuel performance and fission-product (FP) transport models and codes. Each AGR test consists of multiple independently controlled and monitored capsules containing fuel compacts placed in a graphite cylinder shrouded by a steel shell. Release-to-birth ratios (R/B) for fission-gas isotopes released from each capsule are calculated from release rates, measured by germanium detectors in the Fission Product Monitoring System (FPMS) installed downstream from each capsule, and birth rates calculated using numerical models of FG generation. The R/Bs are a critical measure of the ability of the fuel kernel, the particle coating layers, and the compact matrix to retain fission-gas atoms, preventing their release into the sweep-gas flow, and the impact of initially defective particles and/or particle-coating failures that occur during irradiation. For fission-gas isotopes, particle failure is defined as failure of all coating layers, allowing gaseous fission atoms to escape from a particle. During the first five cycles (162B ? 165A), R/Bs were stable in the 10-8?10-6 range, and no in-pile particle failures were observed, based on the gross gamma counts. The maximum R/B value of around 2 ? 10-6 for Kr-85m resulted from the presence of as-fabricated exposed kernels (based on the high exposed kernel fraction), the dispersed uranium, and high fuel particle temperatures in Capsule 1. Comparison of capsule-measured R/Bs from these early cycles to predictions using the previously developed AGR R/B model demonstrated FG release from the AGR-5/6/7 TRISO fuel was comparable to that of previous experiments. In addition, the Kr-85m R/B per-exposed-kernel values are comparable to R/B values obtained in AGR-3/4 irradiation experiment and four irradiation experiments performed during 1980s: (1) HRB-17/18, (2) COMEDIE-BD1, (3) HFR B1, and (4) HRB-21. In contrast, all measured R/B values are lower than predictions by the commonly used Richards and German models, which are intentionally conservative. A large number of in-pile particle failures occurred in Capsule 1 by the end of Cycle 166A. During the final four cycles (166A ? 168A), apparent damage to the Capsule 1 gas line appeared to cause FG leakage from that capsule into the other four capsules, resulting in an increase in fission gas (FG) detected in the effluent for all capsules. Isolation of the Capsule 1 gas line during the last three cycles also prevented measurement of its FG release. Thus, R/Bs in all capsules after Cycle 166A are highly uncertain because of undefined amount of leakage from Capsule 1, especially for long-lived isotopes. A few hundred in-pile particle failures were estimated for Capsule 1 before the end of Cycle 166A, but the total number of failures is unknown due to the lack of FG release data in the later cycles. Based primarily on evidence from the gross gamma counts during Cycle 168A, approximately 15 particles failed in Capsule 3 and four particles failed in Capsule 2. In-pile failures in Capsule 3 were anticipated because this capsule was designed to operate beyond the HTGR normal operating temperature range. In contrast, no in-pile failures were identified in the top two capsules (4 and 5) based on the absence of the typical spikes in gross gamma counts and low failure estimates using the AGR model, developed in INL/EXT-14-32970, for R/B of the short-lived isotopes (Kr-89 and Xe-137) with minimal leakage from Capsule 1.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Multigroup cross section generation capability in GRIFFIN

GRIFFIN is an advanced reactor multiphysics application built on the object-oriented simulation environment (MOOSE) and is jointly developed by Idaho National Laboratory and Argonne National Laboratory. The cross section application programming interface, originally developed for the PROTEUS code, has been integrated into GRIFFIN to prepare cross sections for thermal reactor applications with heterogeneous geometries. Additional improvements have been made by implementing an on-the-fly slowing down method, a double heterogeneity treatment capability, and updating the procedure to generate the fine multigroup library. The cross section preparation capability in GRIFFIN was verified for graphite-moderated TRISO fuel-based reactor benchmark problems: unit-cell problems of VHTR and EMPIRE micro reactor and HTTR assembly problems. Eigenvalues and multigroup cross sections of GRIFFIN agreed very well with those of the continuous-energy Monte Carlo code Serpent2 within 200 pcm in eigenvalue and 2% in cross sections. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Development in DIII-D of High Beta Discharges Appropriate for Steady-state Tokamak Operation With Burning Plasmas

Ideally, tokamak power plants will operate in steady-state at high fusion gain. Recent work at DIII-D on the development of suitable high beta discharges with 100% of the plasma current generated noninductively (f{sub NI} = 1) is described. In a discharge with 1.5 < q{sub min} <2, a scan of the discharge shape squareness was used to find the value that maximizes confinement and achievable {beta}{sub N}. A small bias of the up/down balance of the double-null divertor shape away from the ion B x {del}B drift direction optimizes pumping for minimum density. Electron cyclotron current drive with a broad deposition profile was found to be effective at avoidance of a 2/1 NTM allowing long duration at {beta}{sub N} = 3.7. With these improvements, surface voltage {approx} 0-10 mV, indicating f{sub NI} {approx} 1, was obtained for 0.7 {tau}{sub R} (resistive time). Stationary discharges with {beta}{sub N} = 3.4 and f{sub NI} {approx} 0.9 that project to Q = 5 in ITER have been demonstrated for {tau}{sub R}. For use in development of model based controllers for the q profile, transport code models of the current profile evolution during discharge formation have been validated against the experiment. Tests of available actuators confirm that electron heating during the plasma current ramp up to modify the conductivity is by far the most effective. The empirically designed controller has been improved by use of proportional/integral gain and built-in limits to {beta}{sub N} to avoid instabilities. Two alternate steady-state compatible scenarios predicted to be capable of reaching {beta}{sub N} = 5 have been tested experimentally, motivated by future machines that require high power density and neutron fluence. In a wall stabilized scenario with q{sub min} > 2, {beta}{sub N} = 4 has been achieved for 2 s {approx} {tau}{sub R}. In a high internal inductance scenario, which maximizes the ideal no-wall stability limit, {beta}{sub N} {approx} 4.8 has been reached with f{sub NI} > 1.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

OECD RIA Benchmark Phase II - Towards a better understanding of the RIA fuel modelling

This paper deals with the second phase of the RIA (reactivity initiated accident) fuel rod code benchmark for water-cooled reactors that began in 2014. This second phase has been organized around 2 complementary activities: the first activity is to compare the results of different simulations on simplified cases in order to provide additional bases for understanding the differences in modelling of the concerned phenomena, while the second activity is focused on the assessment of the uncertainty of the results. The detailed specification and comparison of the results from the first activity is presented in this paper. Based on the Phase-I and Phase-II conclusions, some generic recommendations can be made. First, fuel and clad thermomechanical models (with the associated material properties) should be further improved and validated more extensively against a sound RIA database. Secondly, build-up of a comprehensive and robust database consisting of both separate-effect tests and integral tests should be pursued in the short term to reinforce the basis for assessment of both individual model and model integration into codes. Thirdly, an assessment of the uncertainty of fuel thermo-mechanics is of high interest (which is consistent with the second activity of this RIA benchmark Phase-II). Finally, as RIA fuel codes are more and more likely to be used for reactor accident studies, particularly for those involving safety analyses, the fuel rod failure criteria (generally used in such analyses) will have to be carefully justified and validated. The current RIA fuel failure criteria are mainly based on the fuel thermal variables and the verification is based on 'conservative' assumptions for the heat transfer conditions. As all codes give rather consistent evaluations of such variables, it appears possible, taking into account adequate provisions, to derive criteria based on thermal variables from experimental values or from an analytical approach. However, if in the future more mechanistic modelling is ever to be used to establish fuel-failure criteria based on mechanical variables, weaknesses in the validation of the codes identified above will have to be accounted for.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Extension of the high-resolution thermal-hydraulics code ESCOT to hexagonal core geometries for multi-physics calculations

The extension of the capabilities of the pin-level nuclear reactor core thermal-hydraulics (T/H) code ESCOT to analyze hexagonal fueled cores and its performance are presented. ESCOT is an accurate yet fast core thermal-hydraulics solution aiming at high-fidelity and high-resolution multi-physics core analysis in the framework of massively parallel computing platforms. Its algorithm solution is based on the four-equation drift-flux model for two-phase calculations, these are numerically solved by applying the Finite Volume Method (FVM) and the Semi-Implicit Method for Pressure-Linked Equation (SIMPLE)-like algorithm in a staggered grid system. Constitutive models such as turbulent mixing, pressure drop, and vapor generation are employed to simulate key phenomena in subchannel-scale analysis. ESCOT is parallelized by a double (radial and axial) domain decomposition that enables its highly parallelized execution. The coupling of the code with the neutronics whole core solver for hexagonal geometries nTRACER is described. The newly implemented ESCOT features are validated by comparing single assembly and full core steady state nTRACER-ESCOT solutions with nTRACER standalone internal one-dimensional T/H solver results. The validation problems are based on the VVER 440 and VVER 1000 cores. ESCOT results show differences within an acceptable range with respect to the simple 1D nTRACER built-in solver. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Development of a Test System for Verification and Validation of Nuclear transport Simulations

Verification and validation of nuclear data is critical to the accuracy of both stochastic and deterministic particle transport codes. In order to effectively test a set of nuclear data, the data must be applied to a wide variety of transport problems. Performing this task in a timely, efficient manner is tedious. The nuclear data team at Los Alamos National laboratory in collaboration with the University of Florida has developed a methodology to automate the process of nuclear data verification and validation (V and V). This automated V and V process can efficiently test a number of data libraries using well defined benchmark experiments, such as those in the International Criticality Safety Benchmark Experiment Project (ICSBEP). The process is implemented through an integrated set of Python scripts. Material and geometry data are read from an existing medium or given directly by the user to generate a benchmark experiment template file. The user specifies the choice of benchmark templates, codes, and libraries to form a V and V project. The Python scripts generate input decks for multiple transport codes from the templates, run and monitor individual jobs, and parse the relevant output automatically. The output can then be used to generate reports directly or can be stored into a database for later analysis. This methodology eases the burden on the user by reducing the amount of time and effort required for obtaining and compiling calculation results. The resource savings by using this automated methodology could potentially be an enabling technology for more sophisticated data studies, such as nuclear data uncertainty quantification. Once deployed, this tool will allow the nuclear data community to more thoroughly test data libraries leading to higher fidelity data in the future.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

FASTGRASS implementation in BISON and Fission gas behavior characterization in UO 2 and connection to validating MARMOT

This activity is supported by the US Nuclear Energy Advanced Modeling and Simulation (NEAMS) Fuels Product Line (FPL). Two major accomplishments in FY 15 are summarized in this report: (1) implementation of the FASTGRASS module in the BISON code; and (2) a Xe implantation experiment for large-grained UO 2 . Both BISON AND MARMOT codes have been developed by Idaho National Laboratory (INL) to enable next generation fuel performance modeling capability as part of the NEAMS Program FPL. To contribute to the development of the Moose-Bison-Marmot (MBM) code suite, we have implemented the FASTGRASS fission gas model as a module in the BISON code. Based on rate theory formulations, the coupled FASTGRASS module in BISON is capable of modeling LWR oxide fuel fission gas behavior and fission gas release. In addition, we conducted a Xe implantation experiment at the Argonne Tandem Linac Accelerator System (ATLAS) in order to produce the needed UO 2 samples with desired bubble morphology. With these samples, further experiments to study the fission gas diffusivity are planned to provide validation data for the Fission Gas Release Model in MARMOT codes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Multiscale, mechanistic modeling of irradiation-enhanced silver diffusion in TRISO particles

Tristructural isotropic (TRISO) particles are under consideration for use in several proposed advanced nuclear reactor concepts. The silicon carbide (SiC) layer in TRISO acts as a barrier to prevent the release of the fission products. However, despite remarkable retention, silver (Ag) release has been observed from intact particles, which requires investigation since the Ag isotope ( 110m Ag) has a long half-life. Previous work focused on developing a multiscale, mechanistic model for Ag diffusion accounting for temperature and microstructure effect and has been successfully validated. In this work, we expand the previous model to account for irradiation-enhanced Ag diffusivity in SiC and improve its accuracy over a wider grain size and temperature ranges relevant for advanced reactor conditions. A temperature, grain size, and flux dependent diffusivity is therefore derived using the mesoscale code MARMOT and implemented in the fuel performance code BISON. The irradiation-enhanced Ag diffusivity in SiC is compared against experimental data and validated using BISON against Ag release measurements from the Advanced Gas Reactor Fuel Development and Qualification Program (AGR-1 and AGR-2). Herein, we quantify the impact of SiC grain size, irradiation, and temperature on Ag release. In agreement with previous studies, we find accounting for SiC grain size improves agreement between BISON predictions and experimental observations for most cases. In conclusion, we also find that accounting for irradiation improves agreement for cases where Ag release was underestimated, but the impact was less significant than accounting for microstructure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

WE-AB-201-03: TPS Commissioning and QA: Incorporating the Entire Planning Process

Treatment planning systems (TPS) are a cornerstone of modern radiation therapy. Errors in their commissioning or use can have a devastating impact on many patients. To support safe and high quality care, medical physicists must conduct efficient and proper commissioning, good clinical integration, and ongoing quality assurance (QA) of the TPS. AAPM Task Group 53 and related publications have served as seminal benchmarks for TPS commissioning and QA over the past two decades. Over the same time, continuing innovations have made the TPS even more complex and more central to the clinical process. Medical goals are now expressed in terms of the dose and margins around organs and tissues that are delineated from multiple imaging modalities (CT, MR and PET); and even temporally resolved (i.e., 4D) imaging. This information is passed on to optimization algorithms to establish accelerator movements that are programmed directly for IMRT, VMAT and stereotactic treatments. These advances have made commissioning and QA of the TPS much more challenging. This education session reviews up-to-date experience and guidance on this subject; including the recently published AAPM Medical Physics Practice Guideline (MPPG) #5 “Commissioning and QA of Treatment Planning Dose Calculations: Megavoltage Photon and Electron Beams”. Treatment Planning System Commissioning and QA: Challenges and Opportunities (Greg Salomons) This session will provide some key background and review publications describing prominent incidents relating to TPS commissioning and QA. Traditional approaches have been hardware and feature oriented. They aim to establish a functional configuration and establish specifications for regular testing of features (like dose calculation) to assure stable operation and detect failures. With the advent of more complex systems, more patient-specific testing has also been adopted. A number of actual TPS defects will be presented along with heuristics for identifying similar defects in the future. Finally, the Gamma test has become a popular metric for reporting TPS Commissioning and QA results. It simplifies complex testing into a numerical index, but noisy data and casual application can make it misleading. A brief review of the issues around the use of the Gamma test will be presented. TPS commissioning and QA: A process orientation and application of control charts (Michael Sharpe) A framework for commissioning a treatment planning system will be presented, focusing on preparations, practical aspects of configuration, priorities, specifications, and establishing performance. The complexity of the modern TPS make modular testing of features inadequate, and modern QA tools can provide “too much information” about the performance of techniques like IMRT and VMAT. We have adopted a process orientation and quality tools, like control charts, for ongoing TPS QA and assessment of patient-specific tests. The trending nature of these tools reveals the overall performance of the TPS system, and quantifies the variations that arise from individual plans, discrete calculations, and experimentation based on discrete measurements. Examples demonstrating application of these tools to TPS QA will be presented. TPS commissioning and QA: Incorporating the entire planning process (Sasa Mutic) The TPS and its features do not perform in isolation. Instead, the features and modules are key components in a complex process that begins with CT Simulation and extends to treatment delivery, along with image guidance and verification. Most importantly, the TPS is used by people working in a multi-disciplinary environment. It is very difficult to predict the outcomes of human interactions with software. Therefore, an interdisciplinary approach to training, commissioning and QA will be presented, along with an approach to the physics chart check and end-to-end testing as a tool for TPS QA. The role of standardization and automation in QA will also be discussed. The recommendations of MPPG #5 and practical implementation strategies (Jennifer Smilowitz) The recently published recommendations from Task Group No. 244, Medical Physics Practice Guideline on Commissioning and QA of Treatment Planning Dose Calculations: Megavoltage Photon and Electron Beams will be presented. The recommendations focus on the validation of commissioning data and dose calculations. Tolerance values for non-IMRT beam configurations are summarized based on established criteria and data collected by the IROC. More stringent evaluation criteria for IMRT dose calculations are suggested to test the limitations of the TPS dose algorithms for advanced delivery conditions. The MPPG encourages users to create a suite of validation tests for dose calculation for various conditions for static photon beams, heterogeneities, IMRT/VMAT and electron beams. This test suite is intended to be used for subsequent testing, including TPS software upgrades. In the past, the recommendations of some reports have not been widely implemented due to practical limitations. Implementation strategies, tools and processes developed by multiple centers for efficient and “do-able” MPPG #5 testing will be presented, as well as a discussion on the overall validation experience. Learning Objectives: Identify some of the key documents relevant for TPS commissioning and QA Understand strategies for testing TPS software Gain a practical knowledge of the Gamma test criteria Increase familiarity with the process of commissioning a TPS Learn about the use of Control Charts for TPS QA Review the role of the TPS in the overall planning process Increase awareness of the link between TPS QA and chart checking Gain an increased appreciation for the importance of interdisciplinary communication Understand the new recommendations from MPPG #5 on TPS Dose Algorithm Commissioning and QC/QA Learn practical implementation processes and tools for MPPG #5 validation recommendations.

60 APPLIED LIFE SCIENCES↗

Radiation hydrodynamics modelling of kilonovae with SNEC

ABSTRACT We develop a method to compute synthetic kilonova light curves that combine numerical relativity simulations of neutron star mergers and the SNEC radiation–hydrodynamics code. We describe our implementation of initial and boundary conditions, r-process heating, and opacities for kilonova simulations. We validate our approach by carefully checking that energy conservation is satisfied and by comparing the SNEC results with those of two semi-analytic light-curve models. We apply our code to the calculation of colour light curves for three binaries having different mass ratios (equal and unequal mass) and different merger outcome (short-lived and long-lived remnants). We study the sensitivity of our results to hydrodynamic effects, nuclear physics uncertainties in the heating rates, and duration of the merger simulations. We find that hydrodynamics effects are typically negligible and that homologous expansion is a good approximation in most cases. However, pressure forces can amplify the impact of uncertainties in the radioactive heating rates. We also study the impact of shocks possibly launched into the outflows by a relativistic jet. None of our models match AT2017gfo, the kilonova in GW170817. This points to possible deficiencies in our merger simulations and kilonova models that neglect non-LTE effects and possible additional energy injection from the merger remnant and to the need to go beyond the assumption of spherical symmetry adopted in this work.

79 ASTRONOMY AND ASTROPHYSICS↗

Cluster Dynamics Modeling Needs for the Advanced Materials and Manufacturing Technologies Program

This milestone report aims to identify and assess the cluster dynamics (CD) modeling requirements within the Department of Energy's Office of Nuclear Energy (DOE-NE) Advanced Materials and Manufacturing Technologies (AMMT) program and to communicate these needs to the DOE-NE Nuclear Energy Advanced Modeling and Simulation (NEAMS) program. The goal is to ensure NEAMS is well-informed about the CD modeling requirements to support AMMT's mission of accelerating the development, qualification, demonstration, and deployment of advanced structural materials and manufacturing for nuclear energy applications. CD modeling is an essential tool for predicting the degradation of structural materials under irradiation, which is a key component of AMMT's accelerated qualification process. The AMMT program focuses on both additively manufactured and wrought structural alloys, such as laser powder-bed fusion 316H austenitic stainless steel, alloy 709, Haynes 244, and alloy 617. These materials require a generalized CD modeling framework to facilitate rapid model development and computational simulation. A flexible, generalized CD software, similar to the Multiphysics Object-Oriented Simulation Environment (MOOSE) finite element framework, would enable modeling of various cluster types, including defect clusters, defect-solute clusters, and multicomponent clusters, incorporating thermodynamics and kinetics parameters. Radiation effects, microstructural feature evolution, and multi-dimensional modeling are critical considerations for the CD model. The usability of the CD code should allow for easy modification and coupling with MOOSE-based simulations. Additionally, the software should adhere to Nuclear Quality Assurance-1 standards, include a testing suite for verification and validation, and be version-controlled within a national laboratory-managed Git repository. Benchmark problems are needed to assess code predictions and performance.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Refine your search to explore more results.