Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind-tunnel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1956

Effects of vertical fins near the nose of the fuselage on the directional and damping-in-yaw stability derivatives of an airplane model under steady-state and oscillatory conditions

A wind-tunnel investigation has been made at low speed to determine the effects of vertical fins placed ahead of the vertical tail on the directional stability and damping-in-yaw characteristics of a swept-wing model under steady-state oscillatory conditions. Various sizes of fins were used above and below the fuselage center line. The vertical-tail size also was varied.

STABILITY, DIRECTIONAL - STATIC↗
NASA NTRS1957

Ground Effects on the Longitudinal Characteristics of Two Models with Wings Having Low Aspect Ratio and Pointed Tips

Wind-tunnel tests were conducted to determine the ground effects on a tailless model with a wing of aspect ratio 2 and infinite taper, and on a tailed model with a triangular wing of aspect ratio 3, with flaps. Control-surface hinge moments were measured on the tailless model. The results are compared with the predictions of the theory of Tani, et al.

CONTROLS, FLAP-TYPE - COMPLETE WINGS↗
NASA NTRS1948

The effectiveness at high speeds of a 10-percent-chord plain trailing-edge flap on the NACA 65-210 airfoil section

This report contains the results of a high-speed wind-tunnel investigation of the effectiveness of a 10-percent-chord plain flap on the NACA 65-210 airfoil section. The results include an indication of the lift-producing characteristics and the effectiveness of the 10-percent-chord flap. From a comparison of the characteristics of the 10-percent-chord flap with those of a 20-percent-chord flap it was concluded that, although a reduction in flap-chord ratio from 0.20 to 0.10 lessens the severity of the effectiveness loss at supercritical speeds, the 20-percent-chord flap is more effective throughout the entire range of Mach numbers from 0.3 to 0.875.

CONTROLS, FLAP TYPE - WING SECTIONS↗
NASA NTRS1931

The Vertical Wind Tunnel of the National Advisory Committee for Aeronautics

The vertical open-throat wind tunnel of the National Advisory Committee for Aeronautics is described in this report. The tunnel was built mainly for studying the spinning characteristics of airplane models, but may be used as well for the usual types of wind-tunnel tests. A special spinning balance is being developed to measure the desired forces and moments with the model simulating the spin of an airplane. Satisfactory air flow has been attained with a velocity that is uniform over the jet to within plus or minus 0.5 per cent. The turbulence present in the tunnel has been compared with that of several other tunnels by means of the results of sphere drag tests and was found to average well with the values of those tunnels. Included also in the report are comparisons of results of stable autorotation and of rolling-moment test obtained both in the vertical tunnel and in the old horizontal 5-foot atmospheric tunnel. (author)

Wenzinger, Carl J↗
NASA NTRS1923

Point drag and total drag of navy struts no. 1 modified

This report deals with the results of tests on struts conducted at Washington Navy Yard. Two models of the modified Navy strut, no. 1, were tested in the 8 by 8 foot wind tunnel. The tests were made to determine the total resistance end effect and the pressure distribution at various wind-tunnel speeds with the length of the strut transverse to the current. Only the measurements made at zero pitch and yaw are given in this report.

Zahm, A F↗
NASA NTRS1923

The Six-Component Wind Balance

Dr. Zahm's report is a description of the six-component wind-tunnel balance in use at the Aerodynamic Laboratory, Washington Navy Yard. The description of the balance gives the mechanical details and the method of operation, and is accompanied by line drawings showing the construction of the balance. The balance is of particular interest, as it allows the model to be set up quickly and accurately in roll, pitch, and yaw, without stopping the wind. It is possible to measure automatically, directly, and independently the drag, cross-wind force, and lift; also the rolling, pitching, and yawing moments. It is also possible to make the balance self-recording.

Zahm, A F↗
NASA NTRS1929

Drag of C-Class Airship Hulls of Various Fineness Ratios

This report presents the results of wind-tunnel tests on eight C-class airship hulls with various fineness ratios, conducted in the Navy Aerodynamic Laboratory, Washington. The purpose of the tests was to determine the variation of resistance with fineness ratio, and also to find the pressure and friction elements of the total drag for the model having the least shape coefficient. Seven C-class airship hulls with fineness ratios of 1.0, 1.5, 2.0, 3.0, 6.0, 8.0, and 10.0 were made and verified. These models and also the previously constructed original C-class hull, whose fineness ratio is 4.62, were then tested in the 8 by 8 foot tunnel for drag of 0 degree pitch and yaw, at various wind speeds. The original hull, which was found to have the least shape coefficient, was then tested for pressure distribution over the surface at various wind speeds. (author)

Zahm, A F↗
NASA NTRS1929

Pressure Distribution Tests on PW-9 Wing Models from -18 Degree Through 90 Degree Angle of Attack

At the request of the Army Air Corps, an investigation of the pressure distribution over PW-9 wing models was conducted in the atmospheric wind tunnel of the National Advisory Committee for Aeronautics. The primary purpose of these tests was to obtain wind-tunnel data on the load distribution on the cellule to be correlated with similar information obtained in flight tests, both to be used for design purposes. Because of the importance of the conditions beyond the stall as affecting the control and stability, this investigation was extended through 90 degree angle of attack. The results for the range of normal flight have been given in NACA Technical Report No. 271. The present paper presents the same results in a different form and includes, in addition, those over the greater range of angle of attack, -18 degrees through 90 degrees. The results show that: (1) at angles of attack above maximum lift, the biplane upper wing pressures are decreased by the shielding action of the lower wing. (2) the burble of the biplane lower wing, with respect to the angle of attack, is delayed, due to the shielding action of the lower wing. (3) the center of pressure of the biplane upper wing (semispan) is, in general, displaced forward and outward with reference to that of the wing as a monoplane, while for the lower wing there is but slight difference for both conditions. (4) the overhanging portion of the upper wing is little affected by the presence of the lower wing.

Loeser, Oscar E , Jr↗
NASA NTRS1930

Joint Report on Standardization Tests on N.P.L. R.A.F 15 Airfoil Model

This report contains the wind-tunnel test data obtained in the United States on a 36 by 6 inch R.A.F. 15 airfoil model prepared by the British Aeronautical Research Committee for International Trials. Tests were made in cooperation with the National Advisory Committee for Aeronautics at the Bureau of Standards, Langley Memorial Aeronautical Laboratory, Massachusetts Institute of Technology, and McCook field. In addition to brief descriptions of the various wind tunnels and methods of testing, the report contains an analysis of the test data. It is shown that while in general the agreement is quite satisfactory there are two cases in which it is unsatisfactory. Since the lack of agreement in the latter is probably explained by errors known to be inherent in the methods of determining and applying corrections in these particular tests, it is concluded that the agreement obtained is more a matter of technique than a wind tunnel characteristic. (author)

Diehl, Walter S↗
NASA NTRS1930

The Measurement of Fluctuations of Air Speed by the Hot-Wire Anemometer

The hot-wire anemometer suggests itself as a promising method for measuring the fluctuating air velocities found in turbulent flow. The only obstacle is the presence of a lag due to the limited energy input which makes even a fairly small wire incapable of following rapid fluctuations with accuracy. This paper gives the theory of the lag and describes an experimental arrangement for compensating for the lag for frequencies up to 100 or more per second when the amplitude of the fluctuation is not too great. An experimental test of the accuracy of compensation and some results obtained with the apparatus in a wind-tunnel air stream are described. While the apparatus is very bulky in its present form, it is believed possible to develop a more portable arrangement. (author)

Dryden, H L↗
NASA NTRS1930

Flight Tests on U.S.S. Los Angeles. Part II : Stress and Strength Determination

The tests described in this report furnished data on the actual aerodynamic forces, and the resulting stresses and bending moments in the hull of the U. S. S. "Los Angeles" during as severe still-air maneuvers as the airship would normally be subjected to, and in straight flight during as rough air as is likely to occur in service, short of squall or storm conditions. The maximum stresses were found to be within the limits provided for in accepted practice in airship design. Normal flight in rough air was shown to produce forces and stresses about twice as great as the most severe still-air maneuvers. No light was thrown upon the forces which might occur in extreme or exceptional conditions, such as the storm which destroyed the "Shenandoah". The transverse aerodynamic forces on the hull proper were found to be small and irregular. Owing to the necessity of conserving helium, it was impossible to fly the airship in a condition of large excess of buoyancy or weight in order to determine the air pressure distribution at a fixed angle of pitch. However, there is every reason to believe that in that condition the forces on the actual airship are as close to the wind-tunnel results as can be determined by present type of pressure measuring apparatus. It is considered that most important data obtained are the coefficients of tail-surface forces and hull-bending moments. These are tabulated in this report.

Burgess, C P↗
NASA NTRS1931

Airfoil Pressure Distribution Investigation in the Variable Density Wind Tunnel

Report presents the results of wind tunnel tests of pressure distribution measurements over one section each of six airfoils. Pressure distribution diagrams, as well as the integrated characteristics of the airfoils, are given for both a high and a low dynamic scale or, Reynolds number VL/V, for comparison with flight and other wind-tunnel tests, respectively. It is concluded that the scale effect is very important only at angles of attack near the burble. The distribution of pressure over an airfoil having a Joukowski section is compared with the theoretically derived distribution. A further study of the distribution of pressure over all of the airfoils resulted in the development of an approximate method of predicting the pressure distribution along the chord of any normal airfoil for all attitudes within the working range if the distribution at one attitude is known.

Jacobs, Eastman N↗
NASA NTRS1935

A Flight Investigation of the Lateral Control Characteristics of Short Wide Ailerons and Various Spoilers with Different Amounts of Wing Dihedral

This report presents the results of flight tests made to determine the lateral control characteristics of short wide ailerons and spoilers, as a consequence of the promise shown in wind-tunnel tests by these devices as means of obtaining lateral control, particularly at angles of attack above the stall. Several forms of spoilers, front-hinge, rear-hinge, plain retractable, and saw-tooth retractable were tested alone and in combination with the ailerons. The tests were made with several different amounts of wing dihedral so that the effect of the yawing moments of the different lateral control combinations, which varied from large negative to large positive values, could be evaluated. In conjunction with the tests, observations were made to throw some light on the feasibility of operating the airplane with two controls instead of the present three.

Weick, Fred E↗
NASA NTRS1936

Aerodynamic characteristics of wings with cambered external airfoil flaps, including lateral control, with a full-span flap

The results of a wind-tunnel investigation of the NACA 23012, the NACA 23021, and the Clark Y airfoils, each equipped with a cambered external-airfoil flap, are presented in this report. The purpose of the research was to determine the relative merit of the various airfoils in combination with the cambered flap and to investigate the use of the flap as a combined lateral-control and high-lift device.

Platt, Robert C↗
NASA NTRS1938

Tests of Five Full-Scale Propellers in the Presence of a Radial and a Liquid-Cooled Engine Nacelle, Including Tests of Two Spinners

Wind-tunnel tests are reported of five 3-blade 10-foot propellers operating in front of a radial and a liquid-cooled engine nacelle. The range of blade angles investigated extended from 15 degrees to 45 degrees. Two spinners were tested in conjunction with the liquid-cooled engine nacelle. Comparisons are made between propellers having different blade-shank shapes, blades of different thickness, and different airfoil sections. The results show that propellers operating in front of the liquid-cooled engine nacelle had higher take-off efficiencies than when operating in front of the radial engine nacelle; the peak efficiency was higher only when spinners were employed. One spinner increased the propulsive efficiency of the liquid-cooled unit 6 percent for the highest blade-angle setting investigated and less for lower blade angles. The propeller having airfoil sections extending into the hub was superior to one having round blade shanks. The thick propeller having a Clark y section had a higher take-off efficiency than the thinner one, but its maximum efficiency was possibly lower. Of the three blade sections tested, Clark y, R.A.F. 6, and NACA 2400-34, the Clark y was superior for the high-speed condition, but the R.A.F. 6 excelled for the take-off condition.

Biermann, David↗
NASA NTRS1939

Tests of NACA 0009, 0012, and 0018 Airfoils in the Full-Scale Tunnel

An investigation was conducted in the NACA full-scale wind tunnel to determine the aerodynamic characteristics of the NACA 0009, 0012, and 0018 airfoils, with the ultimate purpose of providing data to be used as a basis for comparison with other wind-tunnel data, mainly in the study of scale and turbulence effects. Three symmetrical 6 by 36-foot rectangular airfoils were used. The Reynolds number range for minimum drag was form 1,800,000 to 7,000,000 and for maximum lift, from 1,700,000 to 4,500,000. The effect of rounded tips was determined for each of the airfoils. Tests were also made of the NACA 0012 airfoil equipped with a 0.20c full-span split flap hinged at 0.80c. Tuft surveys were included to show the progressive breakdown of flow near maximum lift. Momentum surveys were made in conjunction with force measurements at zero lift as an aid in converting force-test data to section coefficients.

Goett, Harry J↗
NASA NTRS1939

The Aerodynamic Characteristics of Six Full-Scale Propellers Having Different Airfoil Sections

Wind-tunnel tests are reported of six 3-blade 10-foot propellers operated in front of a liquid-cooled engine nacelle. The propellers were identical except for blade airfoil sections, which were: Clark y, R.A.F. 6, NACA 4400, NACA 2400-34, NACA 2rsub200, and NACA 6400. The range of blade angles investigated extended for 15 degrees to 40 degrees for all propellers except the Clark y, for which it extended to 45 degrees. The results showed that the range in maximum efficiency between the highest and lowest values was about 3 percent. The highest efficiencies were for the low-camber sections.

Biermann, David↗
NASA NTRS1939

Surface heat-transfer coefficients of finned cylinders

An investigation to determine and correlate the experimental surface heat-transfer coefficients of finned cylinders with different air-stream cooling arrangements was conducted at the Langley Memorial Aeronautical Laboratory from 1932 to 1938. The investigation covered the determination of the effect of fin width, fin space, fin thickness, and cylinder diameter on the heat transfer. Wind-tunnel tests were made in the free air stream with and without baffles and also with various devices for creating a turbulent air stream. Tests were also made with blower.

Ellerbrock, Herman H , Jr↗