Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “variance component analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Nuclear Analysis of ITER - Paper 129

The world record fusion power production is 16.1 MW (5.7x10{sup 18} n/s). This was achieved at JET in 1995. The neutron budget during that experimental campaign was 2.5x10{sup 20} neutrons. In the first few seconds of an ITER full power pulse, the neutron production will exceed that the total from the entire history of previous controlled fusion experiments. It is envisaged that ITER should produce as much as 700 MW of fusion power. (This is the maximum envisaged power production from the plasma and does not include power multiplication in the blankets or shielding). This equates to the production of 2.48x10{sup 20} 14-MeV neutrons/s which will give an uncollided flux at the first wall of approximately 4x10{sup 13} n/cm{sup 2}/s and a total with the addition of the collided flux of some 10{sup 14} n/cm{sup 2}/s. For safety and licensing purposes it is the responsibility of ITER to satisfy the host state regulations and must limit doses to the public and staff. Furthermore, sufficient shielding must be provided to ensure that all components function adequately; and for decommissioning, ITER has a responsibility to reduce the volume and radio-toxicity of waste. The construction, operational and decommissioning phases of ITER are expected to last in excess of 30 years and the nuclear issues will be of critical importance throughout this time. The huge leap in neutron production in fusion experiments means that extensive nuclear analysis is required for ITER and it is the thesis of this paper that it is required at an unprecedented level. This is because of the combination of the large physical size of the installation, the variety of radiation sources, the attenuation required, the complexity of the geometry and the complexity of the sources and level of detail required. As a result of this unprecedented challenge the latest techniques for analysis, variance reduction and data display are being employed and in some cases being specifically developed. In this paper a few of the many representative examples of nuclear analysis will illustrate the thesis. The paper includes an examination of areas where further development could be made in the areas of radiation shield and nuclear analysis. Extensive nuclear analysis is required at ITER and the combination of the large physical size of the installation, the variety of radiation sources, the attenuation required, the complexity of the geometry, and the complexity of the sources mean that analysis is required at an unprecedented level of detail and quality. The latest techniques for analysis, variation reduction and data display are being employed and in some cases being specifically developed. Developments are required in areas of analysis, data visualization and experimental verification. (author)

61 RADIATION PROTECTION AND DOSIMETRY↗

Tensor-to-scalar ratio forecasts for extended LiteBIRD frequency configurations

LiteBIRD is a planned JAXA-led cosmic microwave background (CMB) B-mode satellite experiment aiming for launch in the late 2020s, with a primary goal of detecting the imprint of primordial inflationary gravitational waves. Its current baseline focal-plane configuration includes 15 frequency bands between 40 and 402 GHz, fulfilling the mission requirements to detect the amplitude of gravitational waves with the total uncertainty on the tensor-to-scalar ratio, δr, down to δr < 0.001. A key aspect of this performance is accurate astrophysical component separation, and the ability to remove polarized thermal dust emission is particularly important. In this paper we note that the CMB frequency spectrum falls off nearly exponentially above 300 GHz relative to the thermal dust spectral energy distribution, and a relatively minor high frequency extension can therefore result in even lower uncertainties and better model reconstructions. Specifically, we compared the baseline design with five extended configurations, while varying the underlying dust modeling, in each of which the High-Frequency Telescope (HFT) frequency range was shifted logarithmically toward higher frequencies, with an upper cutoff ranging between 400 and 600 GHz. In each case, we measured the tensor-to-scalar ratio r uncertainty and bias using both parametric and minimum-variance component-separation algorithms. When the thermal dust sky model includes a spatially varying spectral index and temperature, we find that the statistical uncertainty on r after foreground cleaning may be reduced by as much as 30–50% by extending the upper limit of the frequency range from 400 to 600 GHz, with most of the improvement already gained at 500 GHz. We also note that a broader frequency range leads to higher residuals when fitting an incorrect dust model, but also it is easier to discriminate between models through higher χ 2 sensitivity. Even in the case in which the fitting procedure does not correspond to the underlying dust model in the sky, and when the highest frequency data cannot be modeled with sufficient fidelity and must be excluded from the analysis, the uncertainty on r increases by only about 5% for a 500 GHz configuration compared to the baseline.

79 ASTRONOMY AND ASTROPHYSICS↗

I Asked 30,000 People in the Nuclear Industry About Safety Culture; This is What I Learned - 19204

Organizations in the nuclear industry place a high value on maintaining the safety of the workforce and community. Some of these organizations do a better job than others when it comes to developing and sustaining a healthy safety culture. We spent six years studying nuclear organizations to better understand the factors that influence safety culture. We used mixed methods to evaluate perceptions of safety culture in these organizations including administering a valid and reliable safety culture survey, conducting one-on-one interviews with managers, and facilitating focus groups with members of the workforce. We analyzed the quantitative and qualitative data collected from more than 30,000 workers in U.S. based organizations. All of the organizations had a nuclear component to their operations. They operated nuclear reactors, processed nuclear materials, decontaminated and decommissioned buildings with radiological contamination, cleaned-up hazardous/mixed waste, and conducted basic science research and development. We talked to craft workers, technicians, engineers, scientific professionals, support personnel, production workers, supervisors and managers. We conducted extensive statistical analysis and learned that, with rare exception, there is a gap between the perceptions of managers and the workforce that they manage. Managers almost always have a more positive perception of safety culture than the people that are actually performing the work. It is not a question of whether there will be a gap; it is simply a matter of the magnitude of the gap. We also learned through exploratory factor analysis that there is one dominant factor that accounted for almost all (75%) of the variance in the perceptions of safety culture. It was the behavior of the leaders, the decisions they made, and the systems they implemented that most influenced the workforce's perception of safety culture. Personal accountability for safety accounted for 14% of the variance, communication and reporting accounted for another 6%. Everything else accounted for the remaining 5%. Management systems, decision making and behavior is the dominant factor and managers almost always have a more positive perception than the people that work for them. People that work in organizations where management exhibits positive decision-making and safety-related behaviors tend to have more positive perceptions of safety culture. Based upon these results, we developed a theory that there were a few important factors on which management could focus on if they sought to influence the safety culture in their organization. Our experience and research suggests that management often fails to recognize five root causes of employee discontent. Employees seek: - To be recognized as an individual; - To be respected; - A sense of stability; - Fairness; - To make a difference. Understanding the perceptions of the workforce is critical because perceptions influence attitudes, which contribute to behaviors that determine individual performance. An organisation's performance is simply the sum of the performance of all of the members of that organization. To change an organisation's safety culture, interventions should target management behavior and decision making for the greatest return on investment. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Evolution of AISI 304L stainless steel part properties due to powder recycling in laser powder-bed fusion

Selective laser melting (SLM) is a powder-bed fusion process in Additive Manufacturing (AM) that uses a laser beam to selectively fuse layers of powder into near net-shape components with little porosity. However, inconsistencies in the part properties due to the presence of defects in as-built components has hindered the widespread adoption of SLM for industrial applications forcing researchers to study the sources of variation for quality control purposes. A critical area suspected of creating variation in the part properties is the feedstock, where batch-to-batch differences as well as changes in the powder properties with reuse have the potential to affect performance. During processing, laser spatter and condensate eject from the melt pool and deposit into the powder-bed surrounding the parts. These particulates, more commonly known as ejecta, differ morphologically and chemically from the virgin powder compromising its reusability. In this study, 304L stainless steel powder was recycled for a total of 5 times through a systematic approach aimed at accelerating powder degradation to reveal the influence on both the tensile and impact toughness properties. Through analysis of variance (ANOVA), it was found that tensile properties did not change with reuse, while the impact toughness showed a steady decline illustrating the differences in static and dynamic part properties due to powder recycling.

36 MATERIALS SCIENCE↗

Accurate determination of genotypic variance of cell wall characteristics of a Populus trichocarpa pedigree using high-throughput pyrolysis-molecular beam mass spectrometry

Abstract Background Pyrolysis-molecular beam mass spectrometry (py-MBMS) analysis of a pedigree of Populus trichocarpa was performed to study the phenotypic plasticity and heritability of lignin content and lignin monomer composition. Instrumental and microspatial environmental variability were observed in the spectral features and corrected to reveal underlying genetic variance of biomass composition. Results Lignin-derived ions (including m/z 124, 154, 168, 194, 210 and others) were highly impacted by microspatial environmental variation which demonstrates phenotypic plasticity of lignin composition in Populus trichocarpa biomass. Broad-sense heritability of lignin composition after correcting for microspatial and instrumental variation was determined to be H 2 = 0.56 based on py-MBMS ions known to derive from lignin. Heritability of lignin monomeric syringyl/guaiacyl ratio ( S / G ) was H 2 = 0.81. Broad-sense heritability was also high (up to H 2 = 0.79) for ions derived from other components of the biomass including phenolics (e.g., salicylates) and C5 sugars (e.g., xylose). Lignin and phenolic ion abundances were primarily driven by maternal effects, and paternal effects were either similar or stronger for the most heritable carbohydrate-derived ions. Conclusions We have shown that many biopolymer-derived ions from py-MBMS show substantial phenotypic plasticity in response to microenvironmental variation in plantations. Nevertheless, broad-sense heritability for biomass composition can be quite high after correcting for spatial environmental variation. This work outlines the importance in accounting for instrumental and microspatial environmental variation in biomass composition data for applications in heritability measurements and genomic selection for breeding poplar for renewable fuels and materials.

09 BIOMASS FUELS↗

A novel method for modeling the neutron time of flight (nTOF) detector response in current mode to inertial confinement fusion experiments.

There are several machines in this country that produce short bursts of neutrons for various applications. A few examples are the Z machine, operated by Sandia National Laboratories in Albuquerque, NM ; the OMEGA Laser Facility at the University of Rochester in Rochester, NY ; and the National Ignition Facility (NIF) operated by the Department of Energy at Lawrence Livermore National Laboratory in Livermore, California . They all incorporate neutron time of flight (nTOF) detectors which measure neutron yield, and the shapes of the waveforms from these detectors contain germane information about the plasma conditions that produce the neutrons. However, the signals can also be %E2%80%9Cclouded%E2%80%9D by a certain fraction of neutrons that scatter off structural components and also arrive at the detectors, thereby making analysis of the plasma conditions more difficult. These detectors operate in current mode - i.e., they have no discrimination, and all the photomultiplier anode charges are integrated rather than counted individually as they are in single event counting. Up to now, there has not been a method for modeling an nTOF detector operating in current mode. MCNP PoliMi was developed in 2002 to simulate neutron and gamma ray detection in a plastic scintillator, which produces a collision data output table about each neutron and photon interaction occurring within the scintillator; however, the post processing code which accompanies MCNP PoliMi assumes a detector operating in single event counting mode and not current mode. Therefore, the idea for this work had been born: could a new post processing code be written to simulate an nTOF detector operating in current mode? And if so, could this process be used to address such issues as the impact of neutron scattering on the primary signal? Also, could it possibly even identify sources of scattering (i.e., structural materials) that could be removed or modified to produce %E2%80%9Ccleaner%E2%80%9D neutron signals? This process was first developed and then applied to the axial neutron time of flight detectors at the Z Facility mentioned above. First, MCNP PoliMi was used to model relevant portions of the facility between the source and the detector locations. To obtain useful statistics, variance reduction was utilized. Then, the resulting collision output table produced by MCNP PoliMi was further analyzed by a MATLAB postprocessing code. This converted the energy deposited by neutron and photon interactions in the plastic scintillator (i.e., nTOF detector) into light output, in units of MeVee%D1%84 (electron equivalent) vs time. The time response of the detector was then folded into the signal via another MATLAB code. The simulated response was then compared with experimental data and shown to be in good agreement. To address the issue of neutron scattering, an %E2%80%9CIdeal Case,%E2%80%9D (i.e., a plastic scintillator was placed at the same distance from the source for each detector location) with no structural components in the problem. This was done to produce as %E2%80%9Cpure%E2%80%9D a neutron signal as possible. The simulated waveform from this %E2%80%9CIdeal Case%E2%80%9D was then compared with the simulated data from the %E2%80%9CFull Scale%E2%80%9D geometry (i.e., the detector at the same location, but with all the structural materials now included). The %E2%80%9CIdeal Case%E2%80%9D was subtracted from the %E2%80%9CFull Scale%E2%80%9D geometry case, and this was determined to be the contribution due to scattering. The time response was deconvolved out of the empirical data, and the contribution due to scattering was then subtracted out of it. A transformation was then made from dN/dt to dN/dE to obtain neutron spectra at two different detector locations.

Nelson, Alan J.↗

Compositional effects on cure kinetics, mechanical properties and printability of dual-cure epoxy/acrylate resins for DIW additive manufacturing

Interest in 3D printing of thermoset resins has increased significantly in recent years. One approach to additive manufacturing of thermoset resins is printing dual-cure resins with direct ink write (DIW). Dual-cure resins are multi-component resins which employ an in situ curable constituent to enable net-shape fabrication while a second constituent and cure mechanism contribute to the final mechanical properties of the printed materials. In this work, the cure kinetics, green strength, printability, and print fidelity of dual-cure epoxy/acrylate thermoset resins are investigated. Resin properties are evaluated as a function of acrylate concentration and in situ UV exposure conditions. The acrylate cure kinetics are probed using photo-differential scanning calorimetry and the impacts of resin composition and UV cure profile on the acrylate extent of conversion are presented. Continuous and pulsed UV cure profiles are shown to affect total conversion due to variances in radical efficiency at different UV intensities and acrylate concentrations. The effects of acrylate concentration on the kinetics of the epoxy thermal cure and the final mechanical properties are also investigated using dynamic mechanical analysis and three-point bend measurements. The glass transition temperature is dependent on formulation, with increasing acrylate content decreasing the T g . However, the room temperature shear moduli, flexural moduli, strength, strain-to-failure, and toughness values are relatively independent of resin composition. The similarity of the final properties allows for greater flexibility in resin formulation and in situ cure parameters, which can enable the printing of complex parts that require high green strength. We found that the in situ UV print intensities and exposure profiles that are necessary to achieve the best print quality are not, in most cases, the conditions that maximize conversion of the acrylate network. Lastly, this highlights the importance of developing optimized resin compositions which enable complete cure of the acrylate network by promoting acrylate dark cure or thermal cure.

36 MATERIALS SCIENCE↗

Influence of living grass Roots and endophytic fungal hyphae on soil hydraulic properties

Soil hydraulic properties are often estimated based on laboratory data or pedotransfer functions dependent on soil physical properties, which often do not consider potential impacts of soil roots or fungal hyphae. Here, we first review current knowledge of how these soil biotic components affect hydraulic properties, then we conducted laboratory experiments to specifically test if the presence of roots and mycorrhizal fungi had a significant effect on the hydraulic properties of two soils with contrasting textures: Flint sand and Hamblen silt loam. Soil cores were seeded with (Panicum virgatum) and grown in a greenhouse over three separate growth periods. The endophytic fungus Serendipita indica was injected as liquid inoculant into designated mycorrhizal cores. Saturated hydraulic conductivity (K sat ) measurements were made with a constant head permeameter, and soil water retention curves were obtained by the evaporation method, supplemented at the dry end for Hamblen silt loam with water activity meter data. Retention curve parameters were obtained by fitting the van Genuchten equation to the resulting measurements. Mean root volume ratios were higher in the mycorrhizal inoculated treatment than in the uninoculated treatment for both soils. For Flint sand, analysis of variance revealed that K sat was reduced by the presence of roots as compared to bare soil. This was likely due to roots clogging soil pores. Results also indicated the presence of roots changed the shape of the water retention curve for Flint sand by increasing water content at saturation and by reducing the slope of the curve. These changes suggested roots created additional porosity and broadened the pore-size distribution. The presence of mycorrhizal fungi accentuated the root effects. The influence of roots and mycorrhizal fungi on hydraulic properties was less obvious for the Hamblen silt loam, as none of the treatments differed from each other at p < 0.05. The results highlight the necessity to consider the impact of root and fungal structures on models of soil hydraulic properties.

59 BASIC BIOLOGICAL SCIENCES↗

Requirements on the gain calibration for LiteBIRD polarisation data with blind component separation

The detection of primordial B modes of the cosmic microwave background (CMB) could provide information about the early stages of the Universe's evolution. The faintness of this signal requires exquisite calibration accuracy and control of instrumental systematic effects which otherwise could bias the measurements. In this work, we study the impact of an imperfect relative polarisation gain calibration on the recovered value of the tensor-to-scalar ratio r for the LiteBIRD experiment, through the application of the blind Needlet Internal Linear Combination (NILC) foreground-cleaning method. We derive requirements on the relative calibration accuracy of the overall polarisation gain (Δg ν ) for each LiteBIRD frequency channel. Our results show that minimum variance techniques, as NILC, are less sensitive to systematic gain calibration uncertainties compared to a parametric approach, if the latter is not equipped with a proper modelling of these instrumental effects. In this study, the most stringent requirements are found in the channels where the CMB signal is relatively brighter, with the tightest constraints at 166 GHz (Δg ν ≈ 0.16%). This differs from the outcome of an analogous analysis performed with a parametric method, where the tightest requirements are obtained for the foreground-dominated channels. Gain calibration uncertainties, corresponding to the derived requirements, are then simultaneously propagated into all frequency channels. By doing so, we find that the overall impact on estimated r is lower than the total gain systematic budget for LiteBIRD approximately by a factor 5, due to the correlations of the impacts of gain calibration uncertainties in different frequency channels. In order to decouple the systematic effect from the specific choice of the model, we derive the requirements assuming constant spectral parameters for the foreground emission. To assess the robustness of the obtained results against more realistic scenarios, we repeat the analysis assuming sky models of intermediate and high complexity. In these further cases, we adopt an optimised NILC pipeline, called the Multi-Clustering NILC (MC-NILC). We find that the impact of gain calibration uncertainties on r is lower than the LiteBIRD gain systematics budget for the intermediate-complexity sky model. For the high-complexity case, instead, it would be necessary to tighten the requirements by a factor 1.8.

79 ASTRONOMY AND ASTROPHYSICS↗

TU-FG-201-09: Predicting Accelerator Dysfunction

Purpose: To develop an integrated statistical process control (SPC) framework using digital performance and component data accumulated within the accelerator system that can detect dysfunction prior to unscheduled downtime. Methods: Seven digital accelerators were monitored for twelve to 18 months. The accelerators were operated in a ‘run to failure mode’ with the individual institutions determining when service would be initiated. Institutions were required to submit detailed service reports. Trajectory and text log files resulting from a robust daily VMAT QA delivery were decoded and evaluated using Individual and Moving Range (I/MR) control charts. The SPC evaluation was presented in a customized dashboard interface that allows the user to review 525 monitored parameters (480 MLC parameters). Chart limits were calculated using a hybrid technique that includes the standard SPC 3σ limits and an empirical factor based on the parameter/system specification. The individual (I) grand mean values and control limit ranges of the I/MR charts of all accelerators were compared using statistical (ranked analysis of variance (ANOVA)) and graphical analyses to determine consistency of operating parameters. Results: When an alarm or warning was directly connected to field service, process control charts predicted dysfunction consistently on beam generation related parameters (BGP)– RF Driver Voltage, Gun Grid Voltage, and Forward Power (W); beam uniformity parameters – angle and position steering coil currents; and Gantry position accuracy parameter: cross correlation max-value. Control charts for individual MLC – cross correlation max-value/position detected 50% to 60% of MLCs serviced prior to dysfunction or failure. In general, non-random changes were detected 5 to 80 days prior to a service intervention. The ANOVA comparison of BGP determined that each accelerator parameter operated at a distinct value. Conclusion: The SPC framework shows promise. Long term monitoring coordinated with service will be required to definitively determine the effectiveness of the model. Varian Medical System, Inc. provided funding in support of the research presented.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

ASSIMILATION OF DOPPLER RADAR DATA INTO NUMERICAL WEATHER MODELS

During the year 2008, the United States National Weather Service (NWS) completed an eight fold increase in sampling capability for weather radars to 250 m resolution. This increase is expected to improve warning lead times by detecting small scale features sooner with increased reliability; however, current NWS operational model domains utilize grid spacing an order of magnitude larger than the radar data resolution, and therefore the added resolution of radar data is not fully exploited. The assimilation of radar reflectivity and velocity data into high resolution numerical weather model forecasts where grid spacing is comparable to the radar data resolution was investigated under a Laboratory Directed Research and Development (LDRD) 'quick hit' grant to determine the impact of improved data resolution on model predictions with specific initial proof of concept application to daily Savannah River Site operations and emergency response. Development of software to process NWS radar reflectivity and radial velocity data was undertaken for assimilation of observations into numerical models. Data values within the radar data volume undergo automated quality control (QC) analysis routines developed in support of this project to eliminate empty/missing data points, decrease anomalous propagation values, and determine error thresholds by utilizing the calculated variances among data values. The Weather Research and Forecasting model (WRF) three dimensional variational data assimilation package (WRF-3DVAR) was used to incorporate the QC'ed radar data into input and boundary conditions. The lack of observational data in the vicinity of SRS available to NWS operational models signifies an important data void where radar observations can provide significant input. These observations greatly enhance the knowledge of storm structures and the environmental conditions which influence their development. As the increase in computational power and availability has made higher resolution real-time model simulations possible, the need to obtain observations to both initialize numerical models and verify their output has become increasingly important. The assimilation of high resolution radar observations therefore provides a vital component in the development and utility of numerical model forecasts for both weather forecasting and contaminant transport, including future opportunities to improve wet deposition computations explicitly.

54 ENVIRONMENTAL SCIENCES↗

Statistical model based iterative reconstruction (MBIR) in clinical CT systems: Experimental assessment of noise performance

Purpose: To reduce radiation dose in CT imaging, the statistical model based iterative reconstruction (MBIR) method has been introduced for clinical use. Based on the principle of MBIR and its nonlinear nature, the noise performance of MBIR is expected to be different from that of the well-understood filtered backprojection (FBP) reconstruction method. The purpose of this work is to experimentally assess the unique noise characteristics of MBIR using a state-of-the-art clinical CT system. Methods: Three physical phantoms, including a water cylinder and two pediatric head phantoms, were scanned in axial scanning mode using a 64-slice CT scanner (Discovery CT750 HD, GE Healthcare, Waukesha, WI) at seven different mAs levels (5, 12.5, 25, 50, 100, 200, 300). At each mAs level, each phantom was repeatedly scanned 50 times to generate an image ensemble for noise analysis. Both the FBP method with a standard kernel and the MBIR method (Veo{sup ®}, GE Healthcare, Waukesha, WI) were used for CT image reconstruction. Three-dimensional (3D) noise power spectrum (NPS), two-dimensional (2D) NPS, and zero-dimensional NPS (noise variance) were assessed both globally and locally. Noise magnitude, noise spatial correlation, noise spatial uniformity and their dose dependence were examined for the two reconstruction methods. Results: (1) At each dose level and at each frequency, the magnitude of the NPS of MBIR was smaller than that of FBP. (2) While the shape of the NPS of FBP was dose-independent, the shape of the NPS of MBIR was strongly dose-dependent; lower dose lead to a “redder” NPS with a lower mean frequency value. (3) The noise standard deviation (σ) of MBIR and dose were found to be related through a power law of σ ∝ (dose){sup −β} with the component β ≈ 0.25, which violated the classical σ ∝ (dose){sup −0.5} power law in FBP. (4) With MBIR, noise reduction was most prominent for thin image slices. (5) MBIR lead to better noise spatial uniformity when compared with FBP. (6) A composite image generated from two MBIR images acquired at two different dose levels (D1 and D2) demonstrated lower noise than that of an image acquired at a dose level of D1+D2. Conclusions: The noise characteristics of the MBIR method are significantly different from those of the FBP method. The well known tradeoff relationship between CT image noise and radiation dose has been modified by MBIR to establish a more gradual dependence of noise on dose. Additionally, some other CT noise properties that had been well understood based on the linear system theory have also been altered by MBIR. Clinical CT scan protocols that had been optimized based on the classical CT noise properties need to be carefully re-evaluated for systems equipped with MBIR in order to maximize the method's potential clinical benefits in dose reduction and/or in CT image quality improvement.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Exploring Afro-Asian water fluxes in CMIP5 and CMIP6 models: Present-day evaluation and future projections

Accurate representation and projection of water fluxes are vital, particularly in monsoon regions where seasonal variability and changes significantly impact water resources, agriculture, hydroelectric power generation, and the economy. This study uses both CMIP5 and CMIP6 models to investigate the present-day representation of key water flux components (including precipitation, evaporation, water vapor, and moisture advection) over the Afro-Asian region during the summer monsoon (JJAS). We also examine future changes under two emission scenarios and assess the underlying physical mechanisms driving these changes while identifying sources of projection uncertainty. Our results show that both models reasonably capture the present-day characteristics of water flux components, although with noticeable biases. Across most regions, we find that CMIP6 models demonstrate slight improvements over CMIP5 in the representation of these components. In a warmer future, a robust intensification of JJAS precipitation (exceeding 0.25 mm/day) is projected across the Afro-Asian region. This increase is largely driven by the vertical thermodynamic term associated with increasing temperature. We find that model uncertainty is the primary source of uncertainty in water flux projections, accounting for over 50 % of the total variance.

Climate change↗

Defect and satellite characteristics of additive manufacturing metal powders

Metal additive manufacturing (AM) requires high-quality metal powders to three-dimensionally (3D) print metallic components with complex and customizable geometries. The lack of quantification of AM metal powders creates quality control challenges for 3D printed components, increases the uncertainty of printing reliability and net cost of inspected and certified printed components, and reduces the recyclability of used powders. However, critical characteristics of AM metal powders that are decisive factors for the 3D printing process, such as internal porosity, contamination, and satellite feature, remain ambiguous. In this work, we developed a novel approach to 3D quantify key characteristics of AM metal powders down to individual particles by using high-resolution synchrotron x-ray computed tomography. Empowered by the penetrative capability of high-energy x-ray, internal porosity and contamination within as-atomized metal powders from high-entropy alloys to nickel-based superalloys were evaluated. Additionally, the newly-developed dispersion method enables the homogeneous separation of individual particles, and consequently, results in the implementation of 3D particle shape analysis. To resolve a major challenge of identification and quantification of satellite-feature particles in as-atomized AM metal powders, the satellite features were quantitated by modeling and analyzing the shape parameter of local thickness variance. Furthermore, the 3D analytical methods of particle assessment in this study can be applied to other materials systems like rock, food, and pharmaceutical particles, and provide insights for process optimization across powder metallurgy, concrete, food and pharmaceutical manufacturing, and AM industries.

36 MATERIALS SCIENCE↗

Combining multiple models to generate consensus: Application to radiation-induced pneumonitis prediction

The fusion of predictions from disparate models has been used in several fields to obtain a more realistic and robust estimate of the ''ground truth'' by allowing the models to reinforce each other when consensus exists, or, conversely, negate each other when there is no consensus. Fusion has been shown to be most effective when the models have some complementary strengths arising from different approaches. In this work, we fuse the results from four common but methodologically different nonlinear multivariate models (Decision Trees, Neural Networks, Support Vector Machines, Self-Organizing Maps) that were trained to predict radiation-induced pneumonitis risk on a database of 219 lung cancer patients treated with radiotherapy (34 with Grade 2+ postradiotherapy pneumonitis). Each model independently incorporated a small number of features from the available set of dose and nondose patient variables to predict pneumonitis; no two models had all features in common. Fusion was achieved by simple averaging of the predictions for each patient from all four models. Since a model's prediction for a patient can be dependent on the patient training set used to build the model, the average of several different predictions from each model was used in the fusion (predictions were made by repeatedly testing each patient with a model built from different cross-validation training sets that excluded the patient being tested). The area under the receiver operating characteristics curve for the fused cross-validated results was 0.79, with lower variance than the individual component models. From the fusion, five features were extracted as the consensus among all four models in predicting radiation pneumonitis. Arranged in order of importance, the features are (1) chemotherapy; (2) equivalent uniform dose (EUD) for exponent a=1.2 to 3; (3) EUD for a=0.5 to 1.2, lung volume receiving >20-30 Gy; (4) female sex; and (5) squamous cell histology. To facilitate ease of interpretation and prospective use, the fused outcome results for the patients were fitted to a logistic probability function.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Walén test and de Hoffmann-Teller frame of interplanetary large-amplitude Alfvén waves

In this study, three methods of analysis are compared to test the Walén relation. Method 1 requires a good de Hoffmann-Teller (HT) frame. Method 2 uses three components separately to find the frame that is slightly modified from Method 1. This method is intended to improve the accuracy of the HT frame and able to demonstrate the anisotropic property of the fluctuations. The better the relation is, the closer the slope of a regression fitting the data of plasma versus Alfvén velocities is to 1. However, this criterion is based on an average HT frame, and the fitted slope does not always work for the Walén test because the HT frame can change so fast in the high-speed streams. We propose Method 3 to check the Walén relation using a sequence of data generated by taking the difference of two consecutive values of plasma and Alfvén velocities, respectively. The difference data are independent of the HT frame. We suggest that the ratio of the variances between plasma and Alfvén velocities is a better parameter to qualify the Walén relation. Four cases in two solar wind streams are studied using these three methods. Our results show that when the solar wind HT frame remains stable, all three methods can predict Alfvénic fluctuations well, but Method 3 can better predict the Walén relation when solar wind contains structures with several small streams. A simulated case also demonstrates that Method 3 is better and more robust than Methods 1 and 2. These results are important for a better understanding of Alfvénic fluctuations and turbulence in the solar wind.

79 ASTRONOMY AND ASTROPHYSICS↗

Application of Principal Component Analysis to Electrochemical Reprocessing PM and NMAC

In this report, data from an electrorefiner (ER) for nuclear fuel reprocessing is evaluated for process monitoring (PM) conclusions. This data comes from tests performed at the Idaho National Laboratory in 2022. Multivariate approaches utilizing methods of Principal Component Analysis (PCA) is applied. This is based off established work in process monitoring for fault detection in industrial facilities. This report will discuss the background, methods, and results of the application and some of the conclusions and applications that can be drawn from them. PCA is applied to two different electrorefiner (ER) operations that occurred at Idaho National Laboratory between August and October 2022. The first operation occurred with little incident while the second had several noted faults in the equipment in operational logs. The data from the first run was used to train the data for “normal” operations and applied to both sets of data to determine when operations were in an “off-normal” condition and identify where the fault occurs through PCA. PCA was able to identify off-normal events and identify the cause for off-normal operations. These identified off-normal events matched with the events and their causes in the operational logs. However, small amounts of variance in the data led to false detection of “off-normal” events. Thus, careful selection of training data and a-posteriori conclusions based off operator assessments will both be required for application of PCA to PM applications. This work demonstrated that multivariate approaches and latent variables are applicable to pyroprocessing PM applications and can be further expanded in future work as quality variables such as salt concentration from sensors and sampling become available.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Spectral distortions to momentum and scalar exchanges by non-turbulent motion and patchy landscape variability

Modifications to the spectra of turbulent velocity and scalars and co-spectra of vertical fluxes of momentum and scalars due to patchy landscape heterogeneity and non-stationarity are explored for a Mediterranean ecosystem. About 9 months of high frequency measurements of the three velocity components, water vapor concentration, carbon dioxide concentration, and air temperature were analyzed for different seasons (spring/summer) and prevalent wind directions (southeast/northwest). The two wind directions sampled a contrast of clumped and patchy landscape comprised of olive trees (southeast) and wall bounded flow disturbed by the presence of few upwind trees (northwest). The measured spectra and co-spectra were also compared to theoretical scaling forms from stationary, planar homogeneous flow, in the absence of subsidence as derived from the Kansas experiment. To assess the role of low frequency non-turbulent motion on the spectral and co-spectral content, a 5-min Fourier cutoff was introduced and the analysis was limited to near-neutral conditions where the boundary layer depth is shallow compared to its unstable counterpart. It was shown that the velocity statistics were not appreciably impacted by the low-frequency motion causing non-stationarity. Moreover, the turbulent scalar fluxes were also shown not to be significantly impacted by such low frequency motion. The scalar variances were impacted, especially the water vapor variance and its concomitant spectral shape. When the non-turbulent motion was filtered, the scalar spectra at low wavenumbers followed expectations from the so-called attached eddy hypothesis (i.e. exhibited a $k^{-1}_x$ scaling with $k_x$ defining the longitudinal wavenumber) applicable for near-neutral conditions. For momentum co-spectra, the canonical shapes from the Kansas experiment appear to describe well the measurements here and in both dominant directions and seasons with some adjustment to the integral time scales based on wind direction. For the scalar co-spectra, deviations from the Kansas experiment were prevalent. The most noticeable and surprising deviations were their slow decay with increased sampling frequency at inertial subrange scales. This slow decay was shown not to contribute appreciably to the overall scalar fluxes. At those fine scales, predictions from local isotropy were expected to hold. The scalar co-spectral deviations from local isotropy were then discussed using a simplified co-spectral budget model where scalar–scalar co-spectra naturally emerged and the interplay between landscape heterogeneity and a scale-dependent pressure-scalar de-correlation time was postulated. It is also envisaged that the findings here offer a preliminary template for analyzing eddy-covariance data in situations that deviate from ideal conditions, especially regarding low-frequency modulations of scalar spectra and vertical scalar flux co-spectra.

Canopy turbulence↗