Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “variable geometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Exploratory wind-tunnel investigation of the effect of the main rotor wake on tail rotor noise

Approaches to minimizing the noise generated by the interaction of the tail rotor blades with the wake of the main rotor considered include repositioning of the tail rotor with respect to the main rotor, changes in the rotational direction of the tail rotor, and modification of the main rotor tip vortex. A variable geometry model was built which had the capability of varying tail rotor position relative to the main rotor as well as direction of tail rotor rotation. Acoustic data taken from the model in the Langley anechoic noise facility indicates interaction effects due to both main rotor shed vortex and the main rotor turbulence.

Pegg, R. J.↗
NASA NTRS1978

Pollution Reduction Technology Program for Small Jet Aircraft Engines, Phase 2

A series of iterative combustor pressure rig tests were conducted on two combustor concepts applied to the AiResearch TFE731-2 turbofan engine combustion system for the purpose of optimizing combustor performance and operating characteristics consistant with low emissions. The two concepts were an axial air-assisted airblast fuel injection configuration with variable-geometry air swirlers and a staged premix/prevaporization configuration. The iterative rig testing and modification sequence on both concepts was intended to provide operational compatibility with the engine and determine one concept for further evaluation in a TFE731-2 engine.

Bruce, T. W.↗
NASA NTRS1978

An aerodynamic analysis of several hypersonic research airplane concepts from M = 0.2 to 6.0

Several conceptual hypersonic research airplanes, designed within the constraints of a B-52 launch aircraft, have been studied experimentally and analytically at Mach numbers from 0.2 to 6.0. Vehicles built to these criteria for Mach 6 cruise were shown to be feasible, if careful attention was paid to the low speed lift, drag, and high angle of attack stability to assure successful landings and transonic pitch angle maneuvers. The integrated scramjet engine drag was high at subsonic speeds and appears to be constant with Reynolds number. The variable geometry airfoil used previously to improve directional stability was shown to be equally adaptable to the improvement of longitudinal stability. The vortex lattice theory gave good subsonic predictions of lift, drag due to lift, and pitching moments. Wind tunnel tests must be relied on for the drag at zero lift, trim, static margins and lateral-directional stability. The Gentry Hypersonic Arbitrary Body Program gave good predictions of the trends of lift, drag, and pitching moments with angle of attack at Mach numbers above 3, but the level of the values were not consistently predicted. No currently available theory or program gave accurate predictions of directional stability or dihedral effects at hypersonic speeds.

Penland, J. A.↗
NASA NTRS1979

Lean, premixed, prevaporized combustor conceptual design study

The seven month study program has the objective to identify and evaluate promising lean, premixed, prevaporized combustor concepts utilizing variable geometry and/or other flow control techniques. The general approach taken to accomplish this objective is outlined and consists of combustor design, design analysis and design ranking. The schedule being taken to achieve this program is shown. Although the ultimate goal of this program is the significant reduction of cruise oxides of nitrogen, both the EPA emission standards and combustor performance levels outlined are retained as goals as well.

Fiorentino, A. J.↗
NASA NTRS1979

Lean, premixed, prevaporized combustor conceptual design study

Phase 1 of the Lean Premixed-Prevaporized Comubstor Design Study is a nine month analytical study effort with no experimental or testing activities included. The program has the objective to design and analyze advanced combustor concepts with features for fuel premixing and prevaporization upstream of the combustion zone for use in future subsonic aircrafts with features for fuel premixing and prevaporization upstream of the combustion zone for use in future subsonic aircraft engines. All of the designs also embody some form of variable geometry for combustor flow modulation. The primary criterion for these designs is low oxides of nitrogen emissions at stratospheric cruise conditions. Four combustor concepts are being designed for the NASA/GE Energy Efficient Engine (EEE) envelope and cycle. Current status of the program is that the four concepts sized for the EEE were designed and are currently undergoing analysis and evaluation.

Ekstedt, E. E.↗
NASA NTRS1979

Multivariable control altitude demonstration on the F100 turbofan engine

The F100 Multivariable control synthesis (MVCS) program, was aimed at demonstrating the benefits of LGR synthesis theory in the design of a multivariable engine control system for operation throughout the flight envelope. The advantages of such procedures include: (1) enhanced performance from cross-coupled controls, (2) maximum use of engine variable geometry, and (3) a systematic design procedure that can be applied efficiently to new engine systems. The control system designed, under the MVCS program, for the Pratt & Whitney F100 turbofan engine is described. Basic components of the control include: (1) a reference value generator for deriving a desired equilibrium state and an approximate control vector, (2) a transition model to produce compatible reference point trajectories during gross transients, (3) gain schedules for producing feedback terms appropriate to the flight condition, and (4) integral switching logic to produce acceptable steady-state performance without engine operating limit exceedance.

Lehtinen, B.↗
NASA NTRS1979

Effect of nose bluntness and afterbody shape on aerodynamic characteristics of a monoplanar missile concept with bodies of circular and elliptical cross sections at a Mach number of 2.50

The tests were performed at a Mach number of 2.50 and at angles of attack from about -4 deg to 32 deg. The results indicate that increasing nose bluntness increases zero lift drag and decreases both the maximum lift-drag ratio and the level of directional stability. The center of pressure generally moves forward with increasing nose size; however, small nose radii on the modified elliptical configurations move the center of pressure rearward. The circular bodied configurations exhibit the greatest longitudinal stability and the least directional stability. Concepts with the variable geometry afterbody contour display the most directional stability and the greatest zero lift drag.

Graves, E. B.↗
NASA NTRS1979

Conceptual study of a turbojet/ramjet inlet

An inlet concept for separate turbojet and ramjet engines was defined and compared with an equivalent inlet for a wraparound turboramjet engine. The comparison was made for a typical high altitude hypersonic cruise vehicle where the turbojet inlet capture area was required to be half as large as the ramjet inlet capture area at cruise. The use of a shorter nacelle having substantially lower cooling requirements at cruise for the inlet concept for separate turbojet and ramjet engines is suggested. The separate engine concept better isolates the turbojet from the ramjet, requires no special close off mechanisms within the turbojet, and avoids the circumferential heat load imposed by a wraparound ramjet. A more variable geometry is required.

Weidner, J. P.↗
NASA NTRS1979

Lean, premixed, prevaporized fuel combustor conceptual design study

Four combustor concepts, designed for the energy efficient engine, utilize variable geometry or other flow modulation techniques to control the equivalence ratio of the initial burning zone. Lean conditions are maintained at high power to control oxides of nitrogen while near stoichometric conditions are maintained at low power for low CO and THC emissions. Each concept was analyzed and ranked for its potential in meeting the goals of the program. Although the primary goal of the program is a low level of nitric oxide emissions at stratospheric cruise conditions, both the ground level EPA emission standards and combustor performance and operational requirements typical of advanced subsonic aircraft engines are retained as goals as well. Based on the analytical projections made, two of the concepts offer the potential of achieving the emission goals; however, the projected operational characteristics and reliability of any concept to perform satisfactorily over an entire aircraft flight envelope would require extensive experimental substantiation before engine adaptation can be considered.

Fiorentino, A. J.↗
NASA NTRS1978

Wide range operation of advanced low NOx aircraft gas turbine combustors

The paper summarizes the results of an experimental test rig program designed to define and demonstrates techniques which would allow the jet-induced circulation and vortex air blast combustors to operate stably with acceptable emissions at simulated engine idle without compromise to the low NOx emissions under the high-altitude supersonic cruise condition. The discussion focuses on the test results of the key combustor modifications for both the simulated engine idle and cruise conditions. Several range-augmentation techniques are demonstrated that allow the lean-reaction premixed aircraft gas turbine combustor to operate with low NOx emissons at engine cruise and acceptable CO and UHC levels at engine idle. These techniques involve several combinations, including variable geometry and fuel switching designs.

Roberts, P. B.↗
NASA NTRS1979

Investigation of flexible nozzle wall-flutter incidents in the NASA-Ames Research Center 11- by 11-foot transonic wind tunnel

Twice during the spring of 1978, the two steel-plate 'flex-walls' that form the variable-geometry nozzle of the 11- by 11-foot tunnel at Ames Research Center experienced a severe dynamic instability. Both walls fluttered in the fundamental beam-bending mode and experienced stresses approaching the yield strength of the material. Both flutter incidents occurred at Mach numbers of about 1.15. The tunnel, operational for 24 years, had no history of such an instability. The cause of these flutter incidents, the steps taken to prevent a recurrence, and the requalification of the facility are described.

Erickson, L. L.↗
NASA NTRS1979

The Advanced Low-Emissions Catalytic-Combustor Program: Phase I - Description and status

The Advanced Low-Emissions Catalytic-Combustor Program is an ongoing three-phase contract effort with the primary objective of evolving the technology required for incorporating catalytic combustors into advanced aircraft gas-turbine engines. Phase I is currently in progress. At the present time, analytical evaluation is being conducted on advanced catalytic-combustor concepts, including variable geometry, with their known inherent potential advantages of low-level pollutant emissions, widened combustion stability limits, and reduced pattern factor for longer turbine life. Phases II and III will consist of experimental evaluation of the most promising concepts.

Szaniszlo, A. J.↗
NASA NTRS1979

Multivariable control altitude demonstration on the F100 turbofan engine

The control system designed under the Multivariable Control Synthesis (MVCS) program for the F100 turbofan engine is described. The MVCS program, applied the linear quadratic regulator (LQR) synthesis methods in the design of a multivariable engine control system to obtain enhanced performance from cross-coupled controls, maximum use of engine variable geometry, and a systematic design procedure that can be applied efficiently to new engine systems. Basic components of the control system, a reference value generator for deriving a desired equilibrium state and an approximate control vector, a transition model to produce compatible reference point trajectories during gross transients, gain schedules for producing feedback terms appropriate to the flight condition, and integral switching logic to produce acceptable steady-state performance without engine operating limit exceedance are described and the details of the F100 implementation presented. The engine altitude test phase of the MVCS program, and engine responses in a variety of test operating points and power transitions are presented.

Lehtinen, B.↗
NASA NTRS1979

Computerized systems analysis and optimization of aircraft engine performance, weight, and life cycle costs

The paper describes the computational techniques employed in determining the optimal propulsion systems for future aircraft applications and to identify system tradeoffs and technology requirements. The computer programs used to perform calculations for all the factors that enter into the selection process of determining the optimum combinations of airplanes and engines are examined. Attention is given to the description of the computer codes including NNEP, WATE, LIFCYC, INSTAL, and POD DRG. A process is illustrated by which turbine engines can be evaluated as to fuel consumption, engine weight, cost and installation effects. Examples are shown as to the benefits of variable geometry and of the tradeoff between fuel burned and engine weights. Future plans for further improvements in the analytical modeling of engine systems are also described.

Fishbach, L. H.↗
NASA NTRS1979

High speed cylindrical rolling element bearing analysis 'CYBEAN' - Analytic formulation

This paper documents the analytic foundation and software architecture for the computerized mathematical simulation of high speed cylindrical rolling element bearing behavior. The software, CYBEAN (CYlindrical BEaring ANalysis), considers a flexible, variable geometry outer ring, EHD films, roller centrifugal and quasidynamic loads, roller tilt and skew, mounting fits, cage and flange interactions. The representation includes both steady state and time transient simulation of thermal interactions internal to and coupled with the surroundings of the bearing. A sample problem illustrating program use is presented.

Kleckner, R. J.↗
NASA NTRS1980

Some effects of cruise speed and engine matching of supersonic inlet design

An analytical study was conducted to determine the impact of flight Mach number on inlet type selection for a supersonic cruise aircraft. External and mixed-compression axisymmetric and two-dimensional inlets were considered. The internal contraction of the mixed-compression inlets was limited to achieve self-starting. At Mach 2.0, the axisymmetric mixed-compression inlet provided the best aircraft range. At Mach 2.3, the two-dimensional mixed-compression inlet was the most attractive if enough variable geometry were incorporated to minimize spillage during subsonic cruise. Increases in takeoff-to-cruise air flow ratio gave lower aircraft range.

Bangert, L. H.↗
NASA NTRS1980

A computer program for the design and analysis of low-speed airfoils, supplement

Three new options were incorporated into an existing computer program for the design and analysis of low speed airfoils. These options permit the analysis of airfoils having variable chord (variable geometry), a boundary layer displacement iteration, and the analysis of the effect of single roughness elements. All three options are described in detail and are included in the FORTRAN IV computer program.

Eppler, R.↗
NASA NTRS1981

Turbine modeling technique to generate off-design performance data for both single and multistage axial-flow turbines

This technique is applicable to larger axial flow turbines which may or may not incorporate variable geometry in the first stage stator. A user specified option will also permit the calculation of design point cooling flow levels and the corresponding change in turbine efficiency. The modeling technique was incorporated into a time sharing computer program in order to facilitate its use. Because this report contains a description of the input output data, values of typical inputs, and example cases, it is suitable as a user's manual.

Converse, G. L.↗