Results for “titanium dioxide” — Page 10

NASA NTRS2016

Erosion Data from the MISSE 8 Polymers Experiment After 2 Years of Space Exposure on the International Space Station

The Polymers Experiment was exposed to the low Earth orbit (LEO) space environment for 2.14 and 2.0 years as part of the Materials International Space Station Experiment 8 (MISSE 8) and the Optical Reflector Materials Experiment-III (ORMatE-III), respectively. The experiment contained 42 samples, which were flown in either ram, wake, or zenith orientations. The primary objective was to determine the effect of solar exposure on the atomic oxygen erosion yield (Ey) of fluoropolymers. This paper provides an overview of the experiment with details on the polymers flown, the characterization techniques used, the atomic oxygen fluence for each exposure orientation, and the LEO Ey results. The Ey values for the fluoropolymers range from 1.45 x 10(exp -25) cm(exp 3)/atom for white Tedlar Registered Trademark (polyvinyl fluoride with white titanium dioxide pigment) flown in the ram orientation to 6.32 x 10(exp -24) cm(exp 3)/atom for aluminized-Teflon Registered Trademark fluorinated ethylene propylene (Al-FEP) flown in the zenith orientation. Erosion yield data for FEP flown in ram, wake and zenith orientations are compared, and the Ey was found to be highly dependent on orientation, hence environmental exposure. Teflon FEP had an order of magnitude higher Ey when flown in the zenith direction (6.32 x10(exp -24) cm(exp3)/atom) as compared to the ram direction (2.37 x 10(exp -25) cm(exp 3)/atom). The Ey of FEP was found to increase with a direct correlation to the solar exposure/AO fluence ratio showing the effect of solar radiation and/or heating due to solar exposure on FEP erosion. In addition, back-surface carbon painted FEP (C-FEP) flown in the zenith orientation had a significantly higher Ey than clear FEP or Al-FEP further indicating that heating has a significant impact on the erosion of FEP, particularly in the zenith orientation.

Solar radiation↗

NASA NTRS2018

Method of Manufacturing a Humidity Sensing Material

A method is provided for manufacturing a humidity sensing material. Particles of a trivalent rare earth hydroxide or oxide (such as lanthanum hydroxide) are mixed with particles of barium oxide and titanium dioxide in specified proportions. The particle mixture is heated to generate a sintered mixture that is milled. The resulting milled particles are mixed with glass particles, an organic surfactant, a solvent, an organic vehicle, and an alkali hydroxide. The resulting liquid mixture is deposited as a layer thereof onto a substrate. The substrate and layer thereon are processed to remove liquid portions of the liquid mixture. Such liquid removal processing includes at least one cycle of heating the layer followed by a corresponding cycle of cooling the layer in a nitrogen atmosphere containing less than 25 parts per million of oxygen.

Rolin, Terry D.↗

NASA NTRS2016

Cryogenic Selective Surfaces

There are many challenges involved in deep-space exploration, but several of these can be mitigated, or even solved, by the development of a coating that can reject most of the Sun's energy and yet still provide some far-infrared heat emission. Such a coating would allow non-heat-generating objects in space to reach cryogenic temperatures without using an active cooling system. This would be a benefit to deep-space sensors that require low temperatures, such as the James Webb Telescope focal plane array. It would also allow the use of superconductors in deep space, which could lead to magnetic energy storage rings, lossless power delivery, or perhaps a large-volume magnetic shield against galactic cosmic radiation. But perhaps the most significant enablement achieved from such a coating would be the long-term storage in deep space of cryogenic liquids, such as liquid oxygen (LOX).In this report, we review the state of the art in low-temperature coatings and calculate the lowest temperatures each of these can achieve, demonstrating that cryogenic temperatures cannot be reached in deep space in this fashion. We then propose a new coating that does allow coated objects in deep space to achieve the very low temperatures required to store liquid oxygen or nitrogen. These new coatings consist of a moderately thick scattering layer (typically 5 mm) composed of a material transparent to most of the solar spectrum. This layer acts as a scatterer to the Sun's light, performing the same process as titanium dioxide in white paint in the visible. Under that layer, we place a metallic reflector, e.g. silver, to reflect long-wave radiation that is not well scattered. The result is a coating we call "Solar White," in that it scatters most of the solar spectrum just as white paint does for the visible. Our modeling of these coatings has shown that temperatures as low as 50 K can be reached for a coated object fully exposed to sunlight at 1 AU from the Sun and far from the Earth.In the second half of the report we explore a mission application of this coating in order to show that it allows LOX to be carried on a mission to Mars. Heat can reach a LOX tank in five ways: direct radiation from the Sun, scattered or reflected radiation from the Sun off of spacecraft components, radiation from nearby planets or the Moon, radiation from the infrared emission of other parts of the spacecraft, and conduction along support struts and flow lines. We discuss these and sum their total contribution when using a Solar White coating to demonstrate an architecture that allows the transportation of LOX to Mars. After this, other applications of Solar White are listed.

Cryogenic Materials↗

NASA NTRS2026

Artemis Suit Material Optical Property Testing of Dust Exposed Fabrics

This paper highlights one aspect of NASA’s ongoing technology-infusion effort to design, fabricate, and test a next-generation outer shell fabric for a lunar Extravehicular Activity (EVA) space suit, a critical component of sustained lunar exploration. Managing thermal loads on the Moon is essential for astronaut safety and suit performance. The suit’s exterior fabric directly influences heat gain and loss through its optical properties: low solar absorptivity minimizes sunlight absorption, while high infrared emissivity aids radiative cooling. Lunar regolith complicates this balance. Its fine, abrasive particles possess unique optical behavior that can lower reflectivity and raise emissivity when embedded in or adhered to fabric surfaces, degrading thermal control and increasing the risk of overheating or cooling inefficiency. To quantify these effects, the Artemis Suit Materials (ASM) team measured solar absorptance and infrared emissivity of clean and dust-soiled Ortho Fabric, establishing beginning-of-life (BOL) and end-of-life (EOL) benchmarks. EOL conditions were simulated with a rotary tumbler abrasion process using lunar dust simulant and ceramic media to reproduce cumulative wear expected during surface operations. Tests also included unmodified fabrics and a fabric/film laminate system containing titanium dioxide to evaluate potential improvements in dust resistance and optical performance. Results from these evaluations provide critical insight into how lunar dust alters fabric thermal behavior and inform the design of bespoke suit materials that maintain required optical properties throughout mission life, supporting safe and effective long-duration EVA on the lunar surface.

space↗

NASA NTRS2026

Artemis Suit Material Optical Property Testing of Dust Exposed Fabrics

This paper highlights one aspect of NASA’s ongoing technology-infusion effort to design, fabricate, and test a next-generation outer shell fabric for a lunar Extravehicular Activity (EVA) space suit, a critical component of sustained lunar exploration. Managing thermal loads on the Moon is essential for astronaut safety and suit performance. The suit’s exterior fabric directly influences heat gain and loss through its optical properties: low solar absorptivity minimizes sunlight absorption, while high infrared emissivity aids radiative cooling. Lunar regolith complicates this balance. Its fine, abrasive particles possess unique optical behavior that can lower reflectivity and raise emissivity when embedded in or adhered to fabric surfaces, degrading thermal control and increasing the risk of overheating or cooling inefficiency. To quantify these effects, the Artemis Suit Materials (ASM) team measured solar absorptance and infrared emissivity of clean and dust-soiled Ortho Fabric, establishing beginning-of-life (BOL) and end-of-life (EOL) benchmarks. EOL conditions were simulated with a rotary tumbler abrasion process using lunar dust simulant and ceramic media to reproduce cumulative wear expected during surface operations. Tests also included unmodified fabrics and a fabric/film laminate system containing titanium dioxide to evaluate potential improvements in dust resistance and optical performance. Results from these evaluations provide critical insight into how lunar dust alters fabric thermal behavior and inform the design of bespoke suit materials that maintain required optical properties throughout mission life, supporting safe and effective long-duration EVA on the lunar surface.

Textile↗

DOE OSTI2020

Hydrophilic, light active coating for membranes

A porous membrane provides enhanced filtration of pollutants and particles by coating the membrane with conformal thin films of doped titanium dioxide via atomic layer deposition or, alternatively, sequential infiltration synthesis. The membrane can either be organic or inorganic, and the doping of the membrane, usually with nitrogen, is an important feature that shifts the optical absorption of the TiO2 from the UV range into the visible-light range. This enables the use of lower energy light, including sunlight, to activate the photocatalytic function of the film. The coating described in the present invention is compatible with virtually any porous membrane and allows for precise tuning of the pore size with molecular precision. The present invention presents a new coating process and chemical structure that provides catalytic activity, strongly enhanced by light, to both mitigate fouling and break down various organic pollutants in the process stream.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Ultrathin, polarization-independent, achromatic metalens for focusing visible light

An optical device includes a titanium dioxide substrate layer on a quartz base of a substrate. The substrate is configured to focus light in visible wavelength spectrum of 400 nm to 700 nm. The substrate comprises a first zone and a second zone. In some embodiments, the first zone and the second zone are concentric circles. A plurality of resonators are disposed on the substrate, the plurality of resonators comprising a first plurality corresponding to the first zone and a second plurality corresponding to the second zone. Each resonator is comprised of a dielectric material with a defined thickness “t” in the range of 30 nm to 300 nm. Each resonator has a radius “r” in the range of 30 nm to 300 nm and a gap “g” between adjacent resonators in the range of 5 nm to 200 nm. The first plurality of resonators in the first zone have a first radius within a first radius range that is different from a second radius range of the second plurality of resonators in the second zone. The plurality of resonators form a metasurface that defines at least in part an ultra-thin achromatic lens of the optical device.

47 OTHER INSTRUMENTATION↗

DOE OSTI2021

Giant polarization in nanodielectrics

The relative permittivity of a material is a scaling factor for capacitors and the devices based upon them; the larger the relative permittivity, the greater the degree of miniaturization, or potential for energy storage. Materials with a relative permittivity than that of silicon nitride (approximately 7) are referred to as high-dielectric constant materials. Values of about 100 are typical in titanium dioxide rutile. Values of about 10,000 are observed in barium titanate in the region of the ferroelectric transition, which while impressive, is not very useful due to the strong temperature dependence. The observation of a relative permittivity of over 100,000 in the calcium copper titanate material sparked considerable interest because it showed little temperature dependence between 100 and 600 K over most of the radio-frequency range. Further investigation revealed that this material appears to be naturally nanotextured and that the colossal permittivity was likely due to the surface and/or internal barrier layer capacitance effect, although the issue is not settled. Unfortunately, the dielectric losses in this class materials are relatively high. A new strategy to achieve high dielectric permittivity with low loss involves using localized lattice defect states through ambipolar co-doping; these intrinsic defect complexes give rise to strong dipoles that are responsible for a relative permittivity of 10,000 with exceptionally low dielectric losses over most of the radio frequency range and excellent thermal stability.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2021

Progress in High-Dielectric Constant Materials

The relative permittivity of a material is a scaling factor for capacitors and the devices based upon them; the larger the relative permittivity, the greater the degree of miniaturization, or potential for energy storage. Materials with a relative permittivity than that of silicon nitride (approximately 7) are referred to as high-dielectric constant materials. Values of about 100 are typical in titanium dioxide rutile. Values of about 10,000 are observed in barium titanate in the region of the ferroelectric transition, which while impressive, is not very useful due to the strong temperature dependence. The observation of a relative permittivity of over 100,000 in the calcium copper titanate material sparked considerable interest because it showed little temperature dependence between 100 and 600 K over most of the radio-frequency range. Further investigation revealed that this material appears to be naturally nanotextured and that the colossal permittivity was likely due to the surface and/or internal barrier layer capacitance effect, although the issue is not settled. Unfortunately, the dielectric losses in this class materials are relatively high. A new strategy to achieve high dielectric permittivity with low loss involves using localized lattice defect states through ambipolar co-doping; these intrinsic defect complexes give rise to strong dipoles that are responsible for a relative permittivity of 10,000 with exceptionally low dielectric losses over most of the radio frequency range and excellent thermal stability.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2022

Developing a High Value Chemical Coproduct: Bio-Base Insecticides from Catalytic Fast Pyrolysis

Coproduction of biochemicals from the thermochemical conversion of biomass is a strategy to reduce biofuel costs and improve bio-oil quality in an integrated biorefinery. (Challenge) Cost effective separations of coproducts from thermochemical conversion streams remains a challenge largely due to the heterogenous nature and stability of thermochemical conversion streams. (Solution) Bio-based insecticides isolated from catalytic fast pyrolysis (CFP) oils are a viable coproduct that can overcome the oil is more stable, they are a high value product, and they can remain a mixture of components. (Approach) This work focuses on the development of a bio-based insecticide coproduct that is distilled from a catalytic fast pyrolysis bio-oil produced using a platinum on titanium dioxide (Pt/TiO2) catalyst to upgrade pyrolysis vapors.

BIOMASS FUELS↗

DOE OSTI2023

Polyoxometalate derivatized metal oxide electrodes

A porous transparent electrode is formed where a film comprising of semiconducting nanoparticles is decorated with polyoxometalates (POMs) bonded to their surfaces. The semiconducting nanoparticles are transparent metal oxide. The semiconducting nanoparticles include tin-doped indium oxide (ITO), fluorine-doped tin oxide (FTO), or titanium dioxide (TiO 2 ). In an embodiment, the POM is [SiW 12 O 40 ]L 4− ; [α-P 2 W 18 O 62 ] 6− ; or [α 2 -P 2 W 17 O 61 ] 10− . The semiconducting nanoparticles bond to the POM through a combination of electrostatic interactions and hydrogen bonds. The porous transparent electrode can be placed in a protonated form or ion-paired with alkali metal cations or tetraalkylammonium cations.

Dares, Christopher J.↗

DOE OSTI2020

A Beehive Inspired Hydrogen Photocatalytic Device Integrating a Carbo–Benzene Triptych Material for Efficient Solar Photo–Reduction of Seawater

The dream to produce green, clean and sustainable hydrogen from earth-abundant and free resources such as seawater and sunlight is highly motivating because of the interest for desirable economical and societal applications in energy. However, it remains challenging to develop an efficient and unassisted photocatalytic device to split seawater molecules with just sunlight without any external bias. For the first time, a such novel hierarchical material has been developed, based on thin film technology that integrates TiO 2 semiconductor layers, embedded gold nanoparticles and a photosensitive carbo-benzene layer. The design of the triptych device placing the photocatalyst in be-to-be increases the photoactive surface area by a factor 2. Its stability (>120 successive hours of hydrogen production and >5 days in a day/night representative alternation) and efficiency (STH 0.06%) are measured in NaCl-salted water. Here, the chloride ions act as hole scavengers and induce an increase of pH increasing in turn the sun-driven hydrogen production rate.

42 ENGINEERING↗

DOE OSTI2020

Revealing and Elucidating ALD-Derived Control of Lithium Plating Microstructure

The practical implementation of Li metal batteries is hindered by difficulties in controlling the Li metal plating microstructure. While previous atomic layer deposition (ALD) studies have focused on directly coating Li metal with thin films for the passivation of the electrode–electrolyte interface, a different approach is adopted, situating the ALD film beneath Li metal and directly on the copper current collector. Here, a mechanistic explanation for this simple strategy of controlling the Li metal plating microstructure using TiO 2 grown on copper foil by ALD is presented. In contrast to previous studies where ALD-grown layers act as artificial interphases, this TiO 2 layer resides at the copper–Li metal interface, acting as a nucleation layer to improve the Li metal plating morphology. Upon lithiation of TiO 2 , a Li x TiO 2 complex forms; this alloy provides a lithiophilic surface layer that enables uniform and reversible Li plating. The reversibility of lithium deposition is evident from the champion cell (5 nm TiO 2 ), which displays an average Coulombic efficiency (CE) of 96% after 150 cycles at a moderate current density of 1 mA cm –2 . This simple approach provides the first account of the mechanism of ALD-derived Li nucleation control and suggests new possibilities for future ALD-synthesized nucleation layers.

25 ENERGY STORAGE↗

DOE OSTI2024

Prediction of Feasibility of Polaronic OER on (110) Surface of Rutile TiO 2

The polaronic effects at the atomic level hold paramount significance for advancing the efficacy of transition metal oxides in applications pertinent to renewable energy. The lattice–distortion mediated localization of photoexcited carriers in the form of polarons plays a pivotal role in the photocatalysis. This investigation focuses on rutile TiO 2 , an important material extensively explored for solar energy conversion in artificial photosynthesis, specifically targeting the generation of green H 2 through photoelectrochemical (PEC) H 2 O splitting. By employing Hubbard-U corrected and hybrid density functional theory (DFT) methods, we systematically probe the polaronic effects in the catalysis of oxygen evolution reaction (OER) on the (110) surface of rutile TiO 2 . Theoretical understanding of polarons within the surface, coupled with simulations of OER at distinct titanium (Ti) and oxygen (O) active sites, reveals diverse polaron formation energies within the lattice sites with strong preference for bulk and surface bridge (O b ) oxygen sites. Moreover, we provide the evidence for the facilitative role of polarons in OER. Here, we find that hole polarons situated at the equatorial oxygen sites near the Ti–active site, along with bridge site hole polarons distal from the O b active site yield a small reduction in OER overpotential by ~0.06 eV and ~0.12 eV, respectively. However, subsurface, equatorial, and bridge site hole polarons significantly reduce the Ti-active site OER overpotential by ~0.4 eV through the peroxo–type oxygen pathway. We also observe that the presence of hole polarons stabilizes the *OH, *O, and *OOH intermediate species compared to the scenario without hole polarons. Overall, this study provides a detailed mechanistic insight into polaron–mediated OER, offering a promising avenue for improving the catalytic activity of transition metal oxide-based photocatalysts catering to renewable energy requisites.

14 SOLAR ENERGY↗

DOE OSTI2023

Screening and Discovery of Metal Compound Active Sites for Strong and Selective Adsorption of N 2 in Air

Photocatalytic nitrogen fixation has the potential to provide a greener route for producing nitrogen-based fertilizers under ambient conditions. Computational screening is a promising route to discover new materials for the nitrogen fixation process, but requires identifying “descriptors” that can be efficiently computed. In this work, we argue that selectivity toward the adsorption of molecular nitrogen and oxygen can act as a key descriptor. A catalyst that can selectively adsorb nitrogen and resist poisoning of oxygen and other molecules present in air has the potential to facilitate the nitrogen fixation process under ambient conditions. Here we provide a framework for active site screening based on multifidelity density functional theory (DFT) calculations for a range of metal oxides, oxyborides, and oxyphosphides. The screening methodology consists of initial low-fidelity fixed geometry calculations and a second screening in which more expensive geometry optimizations were performed. The approach identifies promising active sites on several TiO 2 polymorph surfaces and a VBO 4 surface, and the full nitrogen reduction pathway is studied with the BEEF-vdW and HSE06 functionals on two active sites. The findings suggest that metastable TiO 2 polymorphs may play a role in photocatalytic nitrogen fixation, and that VBO 4 may be an interesting material for further studies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Degradation-resistant TiO 2 @Sn anodes for high-capacity lithium-ion batteries

As the demand for higher-performance batteries has increased, so has the body of research on theoretical high-capacity anode materials. However, the research has been hindered because the high-capacity anode material properties and interactions are not well understood, largely due to the difficulty of observing cycling in situ. Using electrochemical scanning transmission electron microscopy (ec-STEM), we report the real-time observation and electrochemical analysis of pristine tin (Sn) and titanium dioxide-coated Sn (TiO 2 @Sn) electrodes during lithiation/delithiation. As expected, we observed a volume expansion of the pristine Sn electrodes during lithiation, but we further observed that the expansion was followed by Sn detachment from the current collector. Remarkably, although the TiO 2 @Sn electrodes also exhibited similar volume expansion during lithiation, they showed no evidence of Sn detachment. We found that the TiO 2 surface layer acted as an electrochemically activated artificial solid-electrolyte interphase that serves to conduct Li ions. As a physical coating, it mechanically prevented Sn detachment following volume changes during cycling, providing significant degradation resistance and 80% Coulombic efficiency for a complete lithiation/delithiation cycle. Interestingly, upon delithiation, TiO 2 @Sn electrode displayed a self-healing mechanism of small pore formation in the Sn particle followed by agglomeration into several larger pores as delithiation continued.

25 ENERGY STORAGE↗

DOE OSTI2022

Transformation of a ceramic precursor to a biomedical (metallic) alloy: Part I – sinterability of Ta 2 O 5 and TiO 2 mixed oxides

Mixed Ta 2 O 5 – TiO 2 binary system was studied by a combination of differential thermal analysis (DTA), scanning electron microscopy-energy dispersive spectrometry (SEM-EDS), X-ray diffraction (XRD) and in situ high temperature X-ray diffraction (HT-XRD) techniques. Different compositions of the mixed oxide powders were fabricated by ball–milling the powdered compositions, pelletizing the homogenized composite powders, and heating the green pellets in air at different temperatures for fixed time intervals. The sintered pellets were evaluated and characterized with respect to porosity, morphology, and phase distribution. DTA runs of the un-sintered powders indicated the onset temperatures for both exothermic and endothermic changes in the binary system. Significant amount of sintering was observed to take place at temperatures higher than 900 °C. Both room and high temperature X-ray diffraction patterns exhibited consistency in phase formation. A ternary compound (TaTiO 4 ) and a ternary solid solution (Ti 0.33 Ta 0.67 O 2 ) were observed to form in both room and high temperatures in addition to the respective binary phases (Ta 2 O 5 and TiO 2 ). A sintering temperature in the range 900–1000 °C was observed to be adequate to achieve the requisite mechanical strength and optimum internal porosity (40–48%) for subsequent electrochemical polarization experiments.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Pronounced reduction in the regeneration energy of potassium sarcosinate CO 2 capture solvent using TiO 2

Absorption-based CO 2 capture technologies face economic feasibility concerns due to the exceedingly high energy requirements of solvent regeneration. Among various proposed solutions, solid acid-aided solvent regeneration stands out as a promising approach. Studies have shown that solid materials containing Lewis and Brønsted acid sites can facilitate deprotonation of protonated amine and breakdown of carbamate molecules, which significantly increases CO 2 desorption rate and decreases regeneration energy of common solvents such as MEA and DEA. However, the influence of solid acids on alternate solvents such as amino acids is not well known. Here, we report the performance of TiO 2 for the regeneration of CO 2 -loaded aqueous potassium sarcosinate (K-Sar) solvent. K-Sar is an environmentally friendly amino-acid salt that provides high CO 2 absorption rates, making it a good candidate for both point-source and direct-air capture. TiO 2 is hydrothermally stable and contains high surface acid site concentration. Desorption of CO 2 from K-Sar starts at room temperature in the presence of TiO 2 , while such onset temperature is greater than 70°C for regeneration without TiO 2 . Further, at a temperature of 95°C, the maximum CO 2 desorption rate and cumulative CO 2 removal increase by 128% and 91%, respectively, in the presence of TiO 2 compared to the no TiO 2 case. The total regeneration energy could be reduced by ~ 50% with TiO 2 , showcasing the significant role this process can take in improving the commercial competitiveness of absorption-based CO 2 capture. Further characterization with XRD, SEM, and NMR concluded that neither the TiO 2 powder nor the solvent undergoes any physical or chemical degradation in the regeneration process, suggesting the potential of their long-term usability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗