SEARCH · Engineering Papers

Results for “thermogravimetric analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Fabrication, oxidation, and combustion of nanoscale magnesium diboride and tetraboride

The difficult ignition and low combustion efficiency of boron particles decrease the performance of boron-loaded, fuel-rich propellants for solid fuel ramjets and ducted rockets. One approach to solving this problem involves the use of magnesium diboride (MgB 2 ), which ignites easier than boron. Magnesium tetraboride (MgB 4 ) offers greater energy density owing to its higher boron content. However, the effect of B/Mg ratio on the ignition and combustion is unknown. Additionally, while nanoscale MgB₂ particles and quasi-2D structures are promising energetic additives, the oxidation and combustion properties of nanoscale MgB₄ have not been explored. To address these knowledge gaps, the present work included synthesis and high-energy ball milling of MgB 2 and MgB 4 powders, thermogravimetric analysis (TGA) of their oxidation, and combustion experiments with thin layers of the obtained powders. Comparison of two synthesis routes (a solid-state reaction in a tube furnace and combustion synthesis) has shown that the former is the superior method for producing magnesium borides. TGA has revealed that oxidation of both MgB 2 and MgB 4 results in a high conversion into the oxides (88–91 %), far exceeding the low conversion of boron (62.5 %). MgB 4 begins to oxidize rapidly at a much lower temperature (∼900 °C) than MgB 2 (∼1200 °C). The burning rates of milled MgB 2 and MgB 4 are about eight and five times, respectively, faster than that of submicron boron. Magnesium borides exhibit a stable, sustained boron flame, needed for high combustion efficiency, whereas physical Mg/B mixtures undergo Mg-driven "flash" combustion.

Boron↗

DOE OSTI2020

Influence of plasticizers on thermal and mechanical properties of biocomposite filaments made from lignin and polylactic acid for 3D printing

Polylactic acid (PLA) and organosolv lignin were mixed at different ratios and extruded to obtain PLA-lignin composite filaments. PLA was replaced with lignin up to 20 wt%. Two plasticizers (polyethylene glycol (PEG) 2000 and struktol TR451) were added in varying concentrations to enhance the properties of PLA_L20 (20% lignin in PLA) composite filaments. Furthermore, the effect of lignin in PLA, and PEG, and struktol in PLA_L20 composites was investigated via tensile test, differential scanning calorimetry, thermogravimetric analysis, scanning electron microscopy, Fourier transform infrared spectroscopy of the filaments, and dynamic mechanical analysis of 3D printed samples. A 2 wt% PEG was able to enhance both tensile stress and elongation at maximum load of PLA_L20 composite by 19% and 35%, respectively, whereas struktol TR451 was able to improve elongation at maximum load by 24%.

3D printing↗

DOE OSTI2022

Degradation mechanism of blended cement pastes in sulfate-bearing environments under applied electric fields: Sulfate attack vs. decalcification

Applied electric fields, the reason behind stray currents, accelerate the ingress of sulfate into cementitious materials. To identify mitigation approaches, this study investigates the effects of slag and fly ash on sodium sulfate attacks of cement pastes under a constant electric current. The mineralogical alterations induced by the attacks were analyzed using X-ray diffractometry, thermogravimetric analysis, scanning electron microscopy, and thermodynamic modeling. The dissolution of aluminates in the slag and fly ash induced a monosulfate-rich area (>~20 mm from the cathode surface) to form next to the ettringite-rich area on the sample surface (<~20 mm). This effect reduced the availability of SO 4 2– in the pore solution, thereby hindering the penetration of sulfate. Meanwhile, the consumption of portlandite by the pozzolanic reaction lowered the decalcification resistance of the materials. This produced a wide area that endured the decomposition of portlandite and carbonate-AFm. Altogether, blending 30% fly ash did not improve the resistance of the material to either sulfate attacks or decalcification; blending 50% slag can effectively mitigate sulfate ingress, though decalcification may become a governing mechanism in the degradation process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Cr-doped U 3 Si 2 composite fuels under steam corrosion

Dense Cr-doped U 3 Si 2 composite fuels were manufactured by spark plasma sintering, and the effects of Cr addition on mechanical properties and oxidation resistance were investigated. Furthermore, dynamic oxidation testing by thermogravimetric analysis revealed significantly improved oxidation resistance of U 3 Si 2 with minimal doping of 3 wt% Cr. The onset oxidation temperature increased to above 550 °C in air and ~520 °C in steam conditions for the 5 wt% and 10 wt% Cr-doped composites. Steam corrosion testing under 360 °C for 24 hours indicated well-maintained pellet integrity without pulverization for the 10 wt% Cr-doped U 3 Si 2 pellet which only showed minor surface oxidation. The first promising results open up the possibility of designing and manufacturing metal additive-doped U 3 Si 2 composite fuels with significantly-improved corrosion resistance as a potential candidate for accident tolerant fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

Development of copper thiolate organometallic compound as thermal sensitive coating for energy storage system safety

Safety and reliability are primary concerns for the deployment of lithium-ion batteries, especially in electric vehicles (EV) and larger-scale energy storage systems (ESS). Current technology in battery management systems (BMS) includes cell voltage monitoring and positioning temperature sensors in selected locations. For a system with hundreds to thousands of individual batteries, single-point temperature monitoring is inadequate to detect hot spots and cell overheating, which could lead to thermal runaway. Here, we have developed a temperature-sensitive copper-thiol compound that can be directly coated onto battery pouch foils to enable early detection of thermal runaway. Upon reaching specific temperatures, this compound releases a sulfur-containing detectable gas, which can be identified using chemically specific gas sensors to trigger an early warning signal. Such a signal propagate through air offers broad signal coverage and enables a more comprehensive approach to large-area temperature monitoring. The Cu-ethanethiol coating is designed to release volatile gases when the substrate surface temperature exceeds 70 °C, with continuous outgassing as the temperature increases. The compound is composed of Cu, S, Cl, hydrocarbons and trace amounts of oxygen. Upon heating, the oxidation state of Cu(I) transitions to Cu (II), accompanied by gas release. Thermogravimetric analysis coupled with mass spectrometry correlated well with the onset of gas release temperature and emission of sulfur-containing volatile gases. Additionally, an acrylic overcoat is applied to enhance the adhesion of the thermally sensitive compound film to the battery pouch foil. This coating is expected to offer an additional safety layer for ESS, alerting possible thermal runaway events before a failure occurs, thereby allowing sufficient time to implement a mitigation plan.

Early warning systems↗

DOE OSTI2020

Impacts of advanced diesel combustion operation and fuel formulation on soot nanostructure and reactivity

Advanced diesel combustion, accomplished via a single pulse fuel injection and high levels of exhaust gas recirculation (referred to as “PCCI”, partially-premixed charge compression ignition), is shown to be a path to reduce oxides of nitrogen and particulate matter simultaneously. This is well established in the literature. Less established is the extent to which such dilute combustion processes influence soot formation and affect soot that is emitted from diesel engines under such combustion modes. This work focuses on characterization of the nanostructure and oxidative reactivity of soot generated by a light-duty turbodiesel engine operating under a PCCI combustion mode, a dilute, low-temperature combustion process. Previous work on a type of PCCI combustion, referred to as high-efficiency clean combustion (HECC), showed soot samples having a fullerenic nanostructure, characterized by high levels of tortuosity of the fringe layers as seen in transmission electron micrograph images and as quantified using an image processing algorithm. Thermogravimetric analysis of the HECC mode soot samples showed that they displayed higher rates of oxidation than soot samples from a conventional diesel combustion mode. The present work returns to PCCI combustion, considering the timing of the main fuel injection, and the effects of operating on fuels rich in n-alkanes, particularly a fuel produced from a low temperature Fischer-Tropsch process (LTFT) and a renewable diesel fuel (RD) produced via hydrodeoxygenation of a plant oil. PCCI combustion conditions yield soot that shows higher reactivity compared to soot from the conventional combustion mode regardless of fuel type. LTFT and RD fuels produce soots with lower reactivity compared to ULSD. Soots produced from PCCI combustion have higher surface oxygen concentration and higher proportion of amorphous carbon. In addition, TEM images show that PCCI soots from all three fuels have smaller primary particle and particle aggregate sizes, and smaller graphene layers. These properties explain the higher reactivity of soot from PCCI combustion. The less reactive soots, which are produced from LTFT and RD fuel under conventional combustion, show internal burning during oxidation. However, soots with higher reactivity which are produced from late injection PCCI combustion and ULSD show shrinking core oxidation, most likely because of their overall amorphous structure.

42 ENGINEERING↗

DOE OSTI2020

Effect of Si/Al ratio of ZSM-5 support on structure and activity of Mo species in methane dehydroaromatization

The effect of the Si/Al ratio of the ZSM-5 support on the structure and activity of Mo/HZSM-5 catalysts in methane dehydroaromatization (MDA) was studied. ZSM-5 (with Si/Al = 15, 25, and 40) supported Mo oxide catalysts (MoOx/ZSM-5) with 3 and 10 wt% Mo loading were prepared by incipient wetness impregnation followed by calcination in air at 500 °C. The as-prepared catalysts were activated by temperature programmed reduction in hydrogen in order to maximize Mo dispersion. To understand the structure-activity relationship, the fresh and spent samples were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), N2 adsorption isotherms, Scanning Transmission Electron Microscopy with Energy Dispersive X-Ray Spectroscopy (STEM-EDS), X-ray absorption spectroscopy (EXAFS and XANES), thermogravimetric analysis (TGA), and Raman spectroscopy. The results show that the Si/Al ratio does not influence the the local structure around the Mo centers. It does however affect the number of available Brønsted acid sites in the support and the amount of Mo species entering the zeolite channels. A lower Si/Al ratio and higher Mo loading resulted in a higher Mo occupation within the zeolite channels. The higher channel occupation directly correlated with higher benzene selectivity and yield, as well as a lower catalyst deactivation rate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Supercritical, liquid, and gas CO 2 reactive transport and carbonate formation in portland cement mortar

In this paper, we investigate carbonate formation and reactive transport rate in variably saturated portland cement mortars when high concentrations of gas, liquid, or supercritical CO 2 flow through their pore network. Xray computed tomography completed during CO 2 flow is used to quantify the microstructural evolution as the mortar carbonates. After in situ tests, higher resolution scans, thermogravimetric analysis, and desorption isotherm analysis are performed to further quantify microstructural changes. We found that at dry conditions supercritical CO 2 moves more rapidly through the pore space and precipitates more carbonates than liquid or gas CO 2 . However, at 50% degree of saturation (DOS) the CO 2 state did not affect the rate of transport in that each specimen exposed to a different CO 2 state carbonated within the first hour of CO 2 exposure. When the pore space is at 50 or 100% DOS, supercritical CO 2 did not react with hydration products more rapidly nor did it result in more carbonate formation during exposure compared to gas or liquid CO 2 . The amount of Ca(OH) 2 that contributes to CaCO 3 formation is correlated to the DOS. For the mortar composition analyzed, Ca(OH) 2 contributes to approximately 40% of the carbonates formed in the 50% DOS specimens and 15% in the 100% DOS specimens. In other words, as the amount of moisture in the pore space increases, phases other than Ca(OH) 2 contribute to more than 50% of the total CaCO 3 formed.

42 ENGINEERING↗

DOE OSTI2022

Impacts of engine lubrication oil-derived ash on soot oxidative reactivity on a catalytic gasoline particulate filter

Characterizing soot oxidation kinetics is crucial for understanding how gasoline particulate filters (GPFs) perform both in terms of filtration efficiency and pressure drop. The most common method for measuring soot oxidative reactivity is thermogravimetric analysis (TGA). Because TGA is an offline method, it may inaccurately predict how soot oxidizes on a GPF, especially if a catalytic washcoat is present that may enhance oxidation rates through surface interactions as the soot loads on the filter. In this work, a novel in-situ soot oxidative reactivity measurement method was developed. The method involved loading a catalytic GPF under high temperature conditions conducive to soot oxidation and measuring the filtration efficiency of 100 nm particles. A correlation was made between filtration efficiency and loaded soot mass on the filter to allow calculation of the soot oxidation rate. The method was evaluated in experiments using a 2.0 L gasoline direct injection (GDI) engine with three oils of varying additive packages, including an oil with a high zinc dialkyldithiophosphate (ZDDP) concentration, a non-additive, pure poly-alpha olefin (PAO) oil, and an oil with a high concentration of calcium sulfonate. Calculated specific soot oxidation rates ranged from ~0.06–0.6 min –1 and showed strong dependence on GPF inlet gas temperature and lubrication oil additive type. The results clearly demonstrated a catalytic effect of calcium-containing ash particles. Reactivity of soot produced by the engine running with the high calcium containing lubrication oil was increased. Similarly, the results indicated that the catalytic washcoat on the filter increased soot oxidation rates on-filter, especially at low soot loading. Conversely, the ZDDP oil additive exhibited a reactivity inhibiting effect, resulting in lower soot oxidation rates. Finally, this work represents the first known in-situ soot oxidative reactivity measurements on a GPF and elucidates the effect of lubrication oil additives and catalytic washcoat on oxidation rate.

42 ENGINEERING↗

DOE OSTI2020

Spark plasma sintering (SPS) densified U 3 Si 2 pellets: Microstructure control and enhanced mechanical and oxidation properties

Dense U 3 Si 2 pellets with controlled grain structure and enhanced thermal-mechanical and oxidation properties are synthesized with spark plasma sintering (SPS). Microstructure and phase composition of the SPS densified pellets are characterized systematically using SEM, EDS, and XRD. Thermal-mechanical properties and oxidation behavior of the sintered silicide fuel pellets are analyzed by laser flash, indentation, and dynamic thermogravimetric analysis. Dense U 3 Si 2 pellets are consolidated by combining high energy ball milling and rapid sintering by SPS, and the microstructure structures are controlled from micron-sized (~5.7 μm grain size) for conventional silicide to a nanocrystalline matrix with an average grain size of ~280 nm. A dominant phase of distorted U 3 Si 2 was identified with lattice expansion due to residual thermal stress upon SPS consolidation and rapid cooling processes. Both micron-sized and nano-sized pellets show exceptional thermal transport properties, consistent with monolithic silicides reported in literature. The SPS-densified pellets possess simultaneously high hardness and fracture toughness. The SPS-densified silicide pellets also demonstrate exceptional oxidation performance with extended onset oxidation temperature above 500 °C and reduced oxidation kinetics, particularly for nano-sized pellets. A strong strain effect was proposed in which compressive stress in nano-sized pellets enhances the oxidation resistance of silicide fuels, as evidenced by the degradation of oxidation performance upon strain relaxation by isothermal annealing. The correlation among the sintering process – microstructure control – physical properties and fuel behavior is established. A new concept of strain engineering is proposed further properties optimization, enabling the development of potential oxidation and corrosion-resistant silicides with extended performance, the key technological challenge of U 3 Si 2 as the leading concept of accident tolerant fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

High hardness and oxidation-resistant Cr-containing medium entropy ZrTaW diboride

This study reports the successful synthesis of a Cr-containing (Zr 0.30 Ta 0.34 Cr 0.06 W 0.30 )B 2 medium-entropy boride (MEB) via an in-situ reactive borothermal reduction route from oxide precursors. High-energy ball milling was employed to homogenize the precursor mixture prior to reactive densification. X-ray diffraction confirmed the formation of a predominantly AlB₂-type hexagonal diboride structure together with a secondary (W X , M 1-X )B monoboride phase. Microstructural characterization revealed compositional heterogeneity and localized W-rich regions associated with the secondary phase. The synthesized medium-entropy boride exhibited enhanced mechanical properties, which are attributed to lattice distortion and solid-solution strengthening effects. Thermogravimetric analysis revealed complex multistage oxidation behavior, and the oxidation resistance was compared with conventional ultra-high-temperature diborides. The results demonstrate the strong relationship between oxide-derived processing, compositional complexity, phase evolution, and oxidation behavior, highlighting the potential of medium-entropy borides for high-temperature structural applications

36 MATERIALS SCIENCE↗

DOE OSTI2022

Supported molybdenum oxides for the aldol condensation reaction of acetaldehyde

The (retro-)aldol condensation reaction is an important chemical transformation in the upgrading of biomass-derived compounds into fuels and valuable specialty chemicals. In this study, we found that supported molybdenum oxide (MoO x ) catalysts were active and selective for the aldol condensation of acetaldehyde to crotonaldehyde under steady-state reactor conditions. Through a combination of transmission electron microscopy (TEM), ultraviolet–visible (UV–VIS) diffuse reflectance spectroscopy, Fourier transform infrared (FTIR) spectroscopy of adsorbed pyridine, and steady-state reactor testing, we determined that highly dispersed MoO x has a strong interaction with a γ-Al 2 O 3 support resulting in optimal catalyst performance at low weight loadings. In contrast, MoO x particles supported on SiO 2 have a weaker interaction with the support, resulting in a monotonic relationship between Mo loading and aldol condensation activity. The Lewis acid site density and strength are important parameters for predicting aldol condensation activity across all samples. The concentration of weak acid sites had a poor correlation with aldol condensation activity, most likely because these sites are too weak to activate acetaldehyde for the reaction. Medium and strong acid sites both had good correlations to aldol condensation activity. Results from X-ray absorption near edge structure (XANES) and acetaldehyde temperature programmed desorption (TPD) indicated that partially reduced MoO x was more active for aldol condensation, but pretreatment in reducing or oxidizing environments had no significant effect on steady-state catalytic activity. Finally, characterization of spent catalyst samples through temperature programmed oxidation (TPO) and thermogravimetric analysis (TGA) revealed that catalysts with high densities of strong acid sites tended to form more carbonaceous deposits on the surface over the course of the reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Recycled polyethylene and crumb rubber composites modified asphalt with improved aging resistance and thermal stability

Crumb rubbers (CR) and recycled Polyethylene (PE) are commonly used as modifiers to improve the asphalt properties. However, the addition of these modifiers individually may result in phase separation of PE and inadequate degradation of CR, which may not simultaneously satisfy the rheological and aging resistance of the binder blends. In this study, a type of CR/PE composites manufactured through melt extrusion procedures was adopted for the improvement of the modified binder blends. The modified binder blends after short-term (RTFO) and long-term (PAV) aging were collected for dynamic shear rheometer and bending beam rheometer tests. FTIR tests were also used to quantify the aging resistance, while differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were applied to evaluate the thermal behaviors of the binder blends. Optical microscopy tests were used to explore the modification mechanism and visualize the microstructures of original and PAV aged binder blends. Test results showed that CR/PE composites could significantly improve the aging resistance of the binder blends. The dispersed PE particles still interacted with each other and meanwhile worked with the diffused rubbery phase, which could form a similar TPEs network. The oxidation and high-temperature aging of such binder blends would strengthen the network that resisted the aging severity of the binder blends. Furthermore, it was also revealed that CR/PE modified asphalt could sustain more heat before a rapid degradation and the well-dispersed PE particles could interact with the diffused CR particles to form a network to resist aging.

02 PETROLEUM↗

DOE OSTI2024

Carbon sequestration into lime-stabilized soils: Engineering and mineralogical characterization

Stabilizing weak clayey soils with lime is an effective method for improving the mechanical properties of soil. However, lime production is an energy-intensive process producing significant CO 2 emissions in lime-stabilized soils, which can be counteracted through accelerated carbonation that enhances its engineering performance. The present study evaluates accelerated carbonation of lime-treated soils by adding gaseous (CO 2 -rich gas), liquid (water-CO 2 mixture), and solid (sodium bicarbonate) CO 2 sources. Results indicated that samples carbonated with gaseous CO 2 exhibited 100% lime carbonation, while samples treated with solid and aqueous sources of CO 2 had a mean lime carbonation of 60% and 40%, respectively. Further, all lime-treated-carbonated samples exhibited a mean 50% increase in unconfined compressive strength compared to the untreated samples after a 7-day curing period. Durability evaluation through cyclic wetting and drying indicated that the carbonated samples had higher durability than the untreated samples. X-ray computed tomography showed that adding solid and liquid sources of CO 2 facilitated the flocculation of montmorillonite, reducing the porosity. However, a higher dosage of solid CO 2 induced clay dispersion, increasing the porosity. X-ray diffraction and thermogravimetric analysis verified CO 2 sequestration through the formation of calcite, a thermodynamically stable polymorph of calcium carbonate.

58 GEOSCIENCES↗

DOE OSTI2021

A novel solid oxide electrolytic cell with reduced endothermic load for CO 2 electrolysis using (La 0.80 Sr 0.20 ) 0.95 MnO 3-δ cathode

CO 2 conversion to CO via solid oxide electrolysis provides a potentially efficient method for converting CO 2 into an industrially relevant product. A solid oxide electrolysis cell with (La 0.80 Sr 0.20 ) 0.95 MnO 3-δ (LSM) as the CO 2 reduction cathode, yttrium stabilized zirconia (YSZ) as electrolyte, and nickel as the H 2 oxidation anode was operated 800 °C and 850 °C. Thermogravimetric analysis of the LSM material showed no catalyst oxidation at operating temperatures allowing for CO 2 electrolysis without reducing safe gas. In addition, no cathode material mass gain was observed in the presence of CO suggesting little to no carbon deposition occurred above 750 °C. The formation rates of CO for the cell reached 1.15 mL∙min-1∙ cm -2 for an applied current of 150 mA∙cm -2 achieving a faradaic efficiency of 100 %. Furthermore, the cell displayed good stability in the short-term CO 2 electrolysis test with a nominal voltage drop of 4 mV h -1 for 10 h at 850°C. This study shows the feasibility of operating a solid oxide CO 2 electrolysis cell for CO production with H 2 at the anode to reduce endothermic process load.

(La0.80Sr0.20)0.95MnO3-δ↗

DOE OSTI2025

Effect of metal-free mesoporous silica incorporated ZSM-5 composite on thermo-catalytic pyrolysis of polypropylene

Although different zeolites impregnated with transition metals have been used in catalytic deconstruction of waste plastics to other products, the influence of hierarchical structures on conversion and product selectivity in plastic upcycling has not been thoroughly investigated. This research explores a transition metal free zeolite-based hierarchical composite, synthesized by incorporating SBA-15 in ZSM-5 framework, for efficient thermos-catalytic upcycling of polypropylene (PP). Thermogravimetric analysis reveals that ZSM-5@SBA-15 can break down PP at a significantly lower temperature, 240 °C, compared to that of pristine PP using ZSM-5 or SBA-15. In addition, pyrolysis of PP at 400 °C using ZSM-5@SBA-15 composite outperforms ZSM-5 or SBA-15 used separately and yields 90 % conversion with 70 % selectivity to propene. The presence of mesopores in the catalyst appears to reduce the diffusion resistance of intermediate products for successive scission, thereby reducing the activation energy of reaction and improving catalytic activity. In conclusion, the hierarchical composite ZSM-5@SBA-15 has significant potential for upcycling of PP into valuable monomers and lighter olefins, with lower energy demands, enhancing the economic feasibility of the process.

ZSM-5@SBA-15↗

DOE OSTI2025

Enhanced grindability of bastnaesite ore by ex-situ CO 2 treatment under the partial pressure of 0-100 psi

High grinding energy consumption has long constrained the sustainable development of mineral processing. This study introduces an innovative technology that employs ex-situ CO 2 treatment to enhance the grindability of bastnaesite ore. The grinding aid effect was evaluated under CO 2 partial pressures ranging from 0 psi to 100 psi using particle size distribution and the Bond work index (BWI), while the underlying mechanism was elucidated with various characterization techniques including inductively coupled plasma (ICP), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and Brunauer-Emmett-Teller (BET). The optimal grinding aid effect was achieved at 100 psi partial pressure, 50% slurry concentration, and 3 h reaction duration. Correspondingly, the P80 of the grinding product decreased from 81.76 μm to 72.73 μm and the BWI of bastnaesite ore decreased from 6.96 kW·h/t to 6.30 kW·h/t, a reduction of 9.48%. The grinding aid effect primarily resulted from the transformation of sparingly soluble carbonates like calcite and dolomite into more soluble bicarbonates, which created substantial cracks and pores, thereby reducing the ore's hardness and improving its grindability. By significantly saving grinding energy consumption while delivering environmental benefits, this technology exhibits great promise for further optimization and widespread adoption.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Adsorptive denitrogenation of model aviation fuel using mesoporous silica in a packed bed adsorption system

This study aims to understand the effects of system process parameters such as flow rate, adsorbent particle size, and use of recycled adsorbent on denitrogenation performance of a model fuel using mesoporous silica gel. The goal is to reduce the nitrogen content of the model fuel from 1500 parts per million to single-digit ppm to meet ASTM specifications for drop-in fuels. This work was done with the intent of applying adsorptive denitrogenation to sustainable aviation fuel (SAF) product fractions produced via hydrothermal liquefaction (HTL). The adsorption performance of the silica is evaluated via packed column breakthrough data, with data generated from collecting from the column outlet and quantifying nitrogen content via gas chromatography. Select experiments use a significantly larger (2.5x column diameter and length) column to demonstrate linear scalability of the process. Thermogravimetric analysis data is collected to evaluate the effects of thermal calcination as a sorbent regeneration method. Effects of a more complex feed are also investigated using a known reference fuel with additional added nitrogen containing compounds. The results presented in this work successfully demonstrate up to 99.8 % removal of NCCs from a model fuel fraction at an original NCC concentration of approximately 1500 ppm to single-digit parts per million after treatment. We also examine calcination of sorbent materials to remove the adsorbed species to enable sorbent reuse and minimize waste generation and show that the calcined material can be reused up to 5 cycles with reduced adsorption capacity. Overall, this work indicates that adsorptive denitrogenation using silica gel is a viable solution to enable the integration of HTL-derived aviation fuels into existing fuel infrastructure.

Adsorption techniques↗