Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface morphologies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Near-terminator photography, part R

The advantages resulting from the use of near-terminator photography in lunar surface investigations are discussed. It is pointed out that, under near-terminator conditions, small changes in slope produce greater contrast changes than at high sun elevation angles. This desirable phenomenon is confirmed by an examination of the near-terminator photography taken during the Apollo 15 mission. Many of the photographs obtained show lunar surface areas within a few degrees of the terminator and are therefore of significant geologic interest. In addition, many geologic features stand out in a distinct manner not normal in conventional lunar photography, thus providing additional data on the surface morphology and the configuration of a large number of lunar surface structures.

Head, J. W.↗
NASA NTRS1987

Degradation mechanisms of materials for large space systems in low Earth orbit

Degradation was explored of various materials used in aerospace vehicles after severe loss of polymeric material coatings (Kapton) was observed on an early shuttle flight in low Earth orbit. Since atomic oxygen is the major component of the atmosphere at 300 km, and the shuttle's orbital velocity produced relative motion corresponding to approx. 5 eV of oxygen energy, it was natural to attribute much of this degradation to oxygen interaction. This assumption was tested using large volume vacuum systems and ion beam sources, in an exploratory effort to produce atomic oxygen of the appropriate energy, and to observe mass loss from various samples as well as optical radiation. Several investigations were initiated and the results of these investigations are presented in four papers. These papers are summarized. They are entitled: (1) The Space Shuttle Glow; (2) Laboratory Degradation of Kapton in a Low Energy Oxygen Ion Beam; (3) The Energy Dependence and Surface Morphology of Kapton Degradation Under Atomic Oxygen Bombardment; and (4) Surface Analysis of STS 8 Samples.

Gordon, William L.↗
NASA NTRS1999

Structure and Morphology of Phthalocyanine Films Grown in Electrical Fields by Vapor Deposition

Phthalocyanine is a very stable organic material in the atmosphere and has been used in numerous applications, such as optical switching and optical storage devices. Although this material has already been discovered for several decades and has had extensive studies conducted on it, many properties still need to be better understood, for example, the mechanisms of forming different solid phases and of changing film morphology by external forces. Phthalocyanine has two preferred solid phases (alpha and beta phases) for which the crystal structures, surface morphology and optical properties are different. In order to investigate these phenomena and the relationship among them, phthalocyanine films have been synthesized by vapor deposition on quartz substrates with and without an external electrical field. Some substrates were coated with a very thin gold film for the electrical field. These films have been characterized using x-ray diffraction, scanning electron microscopy, Fourier transfer infrared spectroscopy, and Z-scan technique. The films have excellent chemical and thermal stability. However, the surface of these films grown without the electrical field shows flower-like morphology. When films are deposited under an electrical field (approximately 3000 V/cm), an aligned structure is revealed on the surface. A comparison of the structure, morphology, optical properties, and the growth mechanism for these films with and without an electrical field will be discussed.

Zhu, Shen↗
NASA NTRS1978

Sublimate morphology on 74001 and 74002 orange and black glassy droplets

SEM-EDX analysis of the surface morphology of the 74001 and 74002 orange and black glassy droplets has revealed the presence of ubiquitous micromound coatings. Assuming that the diameter of an individual micromound is an indication of total coating thickness, then the thickness of this volatile and metal-rich layer ranges from less than 20 A to over 300 A in thickness. On rare droplets the micromound coating is partially covered by a sparse population of crystals and masses that are essentially NaCl in composition. Additionally, an irregular mass on the surface of one black droplet may contain free sulfur. Amoeboid masses of iron, some with incipient crystal faces, are also present on a few droplet surfaces. The above features, i.e., halite crystals, sulfur-rich masses and amoeboid iron, are rare; the more common occurrence of metals and volatiles is in the micromound coating. Based on our observations of several hundred spheres from both Apollo and Luna missions, the classic micromound coating is unique to the Apollo 15 green and Apollo 17 orange and black droplets. Although some investigators have proposed various impact sequences to produce these unique droplets, the volcanic fire fountain origin is favored.

Clanton, U. S.↗
DOE OSTI2021

Flexural strength of a conventionally processed and additively manufactured debased 94% alumina

Mechanical strength of a 94 wt% debased alumina was measured using ASTM-C1161 specimens fabricated via conventional and lithography-based ceramic manufacturing (LCM) methods. The effects of build orientation and a 1500°C wet hydrogen fire added to the LCM firing sequence on strength were evaluated. Additionally, a Weibull fit to the conventional flexural specimen data yielded 20 and 356 MPa for the modulus and characteristic strength, respectively. Weibull fits of the data from the LCM specimens yielded moduli between 7.5 and 11.3 and characteristics strengths between 333 and 339 MPa. A Weibull fit to data from LCM specimens subjected to the wet hydrogen fire yielded 14.2 and 376 MPa for the modulus and characteristic strength, respectively. The 95% confidence intervals for all Weibull parameters are reported. Average Archimedes bulk densities of LCM and conventional specimens were 3.732 and 3.730 g/cm 3 , respectively. Process dependent differences in surface morphology were observed in scanning electron microscope (SEM) images of specimen surfaces. SEM images of LCM specimen cross-sections showed alumina grain texture dependent on build direction, but no evidence of porosity concentrated in planes between printed layers. Fracture surfaces of LCM and conventionally processed specimens revealed hackle lines and mirror regions indicative of fracture initiation at the sample surface rather than the interior.

36 MATERIALS SCIENCE↗
NASA NTRS1991

Space environmental effects on silvered Teflon thermal control surfaces

Cumulative space environment effects on Ag/fluorinated ethylene propylene (FEP) were a function of exposure orientation. Samples from nineteen silvered Teflon (Ag/FEP) thermal control surfaces recovered from the Long Duration Exposure Facility (LDEF) were analyzed to determine changes in this material as a function of position on the spacecraft. Although solar absorptance and infrared emittance of measured thermal blanket specimens are relatively unchanged from control specimen values, significant changes in surface morphology, composition and chemistry were observed. Researchers hypothesize that the FEP surfaces on LDEF were degraded by ultraviolet radiation exposure at all orientations, but that the damaged material had been removed by erosion from the blankets exposed to atomic oxygen flux and that contamination is masking the damage on trays flanking the trailing edge.

Hemminger, C. S.↗
NASA NTRS1992

Space environmental effects on silvered Teflon thermal control surfaces

Cumulative space environmental effects on silver/fluorinated ethylene propylene (Ag/FEP) were a function of exposure orientation. Samples from nineteen silvered Teflon (Ag/FEP) thermal control surfaces recovered from the Long Duration Exposure Facility (LDEF) were analyzed to determine changes in this material as a function of position on the spacecraft. Although solar absorptance and infrared emittance of measured thermal blanket specimens are relatively unchanged from control specimen values, significant changes in surface morphology, composition, and chemistry were observed. We hypothesize that the FEP surfaces on the LDEF are degraded by UV radiation at all orientations, but that the damaged material has been removed by erosion from the blankets exposed to atomic oxygen flux and that contamination is masking the damage in some areas on the trays flanking the trailing edge.

Hemminger, C. S.↗
NASA NTRS2011

Preliminary Examination of Particles Recovered from the Surface of the Asteroid Itokawa by the Hayabusa Mission

The Hayabusa spacecraft arrived at S-type Asteroid 25143 Itokawa in November 2006, and reveal astounding features of the small asteroid (535 x 294 x 209 m). Near-infrared spectral shape indicates that the surface of this body has an olivinerich mineral assemblage potentially similar to that of LL5 or LL6 chondrites with different degrees of space weathering. Based on the surface morphological features observed in high-resolution images of Itokawa s surface, two major types of boulders were distinguished: rounded and angular boulders. Rounded boulders seem to be breccias, while angular boulders seem to have severe impact origin. Although the sample collection did not be made by normal operations, it was considered that some amount of samples, probably small particles of regolith, was collected from MUSES-C regio on the Itokawa s surface. The sample capsule was successfully recovered on the earth on June 13, 2010, and was opened at curation facility of JAXA (Japan Aerospace Exploration Agency), Sagamihara, Japan. A large number of small particles were found in the sample container. Preliminary analysis with SEM/EDX at the curation facility showed that at least more than 1500 grains were identified as rocky particles, and most of them were judged to be of extraterrestrial origin, and definitely from Asteroid Itokawa. Minerals (olivine, low-Ca pyroxene, high-Ca pyroxene, plagioclase, Fe sulfide, Fe-Ni metal, chromite, Ca phosphate), roughly estimated mode the minerals and rough measurement of the chemical compositions of the silicates show that these particles are roughly similar to LL chondrites. Although their size are mostly less than 10 m, some larger particles of about 100 m or larger were also identified. A part of the sample (probably several tens particles) will be selected by Hayabusa sample curation team and examined preliminary in Japan within one year after the sample recovery in prior to detailed analysis phase. Hayabusa Asteroidal Sample Preliminary Examination Team (HASPET) has been preparing for the preliminary examination with close cooperation with the curation team.

Tsuchiyama, A.↗
NASA NTRS2014

Precision Control of Thermal Transport in Cryogenic Single-Crystal Silicon Devices

We report on the diffusive-ballistic thermal conductance of multi-moded single-crystal silicon beams measured below 1 K. It is shown that the phonon mean-free-path is a strong function of the surface roughness characteristics of the beams. This effect is enhanced in diffuse beams with lengths much larger than, even when the surface is fairly smooth, 510 nm rms, and the peak thermal wavelength is 0.6 microns. Resonant phonon scattering has been observed in beams with a pitted surface morphology and characteristic pit depth of 30 nm. Hence, if the surface roughness is not adequately controlled, the thermal conductance can vary significantly for diffuse beams fabricated across a wafer. In contrast, when the beam length is of order, the conductance is dominated by ballistic transport and is effectively set by the beam cross-sectional area. We have demonstrated a uniformity of +/-8% in fractional deviation for ballistic beams, and this deviation is largely set by the thermal conductance of diffuse beams that support the micro-electro-mechanical device and electrical leads. In addition, we have found no evidence for excess specific heat in single-crystal silicon membranes. This allows for the precise control of the device heat capacity with normal metal films. We discuss the results in the context of the design and fabrication of large-format arrays of far-infrared and millimeter wavelength cryogenic detectors.

multi-moded single-crystal silicon beams↗
DOE OSTI2021

Suppression of electroconvective and morphological instabilities by an imposed cross flow of the electrolyte

Electroconvective (EC) instability and its influence on surface morphological perturbations (Morph) are important in many applications, including electrodialysis, batteries, and fuel cells. In this work, we study the effects of a two-dimensional channel flow on the EC and Morph instabilities using two approaches. In the bulk analysis, we derive the asymptotic solutions for small and large wave numbers by neglecting the space charge layer and imposing a second kind electroosmosis slip velocity boundary condition on the electroneutral bulk region. In the full analysis, the instability of the entire region of the liquid electrolyte is analyzed using the ultraspherical spectral method. Both studies show that the flow significantly affects the EC instability. The imposed flow distorts the concentration field, causing a sheltering effect which hinders the ion transport from low- to high-concentration regions, and therefore suppresses the EC instability below a certain wave number. In combination with the viscous stabilization of the high wave number modes by the space charge layer, a sufficiently strong imposed flow can fully suppress the EC instability. The increment in the critical voltage for the instability onset is roughly proportional to the square root of the product of imposed velocity and double layer thickness. The imposed flow has a smaller effect on the Morph instability, except that it may remove the morphological modes resulting from the EC instability and thereby change the wave number of the most unstable mode.

42 ENGINEERING↗
DOE OSTI2021

The Surface Chemistry and Structure of Colloidal Lead Halide Perovskite Nanocrystals

Since the initial discovery of colloidal lead halide perovskite nanocrystals, there has been significant interest placed on these semiconductors because of their remarkable optoelectronic properties, including very high photoluminescence quantum yields, narrow size- and composition-tunable emission over a wide color gamut, defect tolerance, and suppressed blinking. These material attributes have made them attractive components for next-generation solar cells, light emitting diodes, low-threshold lasers, single photon emitters, and X-ray scintillators. While a great deal of research has gone into the various applications of colloidal lead halide perovskite nanocrystals, comparatively little work has focused on the fundamental surface chemistry of these materials. While the surface chemistry of colloidal semiconductor nanocrystals is generally affected by their particle morphology, surface stoichiometry, and organic ligands that contribute to the first coordination sphere of their surface atoms, these attributes are markedly different in lead halide perovskite nanocrystals because of their ionicity. Herein, emerging work on the surface chemistry of lead halide perovskite nanocrystals is highlighted, with a particular focus placed on the most-studied composition of CsPbBr 3 . We begin with an in-depth exploration of the native surface chemistry of as-prepared, 0-D cuboidal CsPbBr 3 nanocrystals, including an atomistic description of their surface termini, vacancies, and ionic bonding with ligands. We then proceed to discuss various post-synthetic surface treatments that have been developed to increase the photoluminescence quantum yields and stability of CsPbBr 3 nanocrystals, including the use of tetraalkylammonium bromides, metal bromides, zwitterions, and phosphonic acids, and how these various ligands are known to bind to the nanocrystal surface. To underscore the effect of post-synthetic surface treatments on the application of these materials, we focus on lead halide perovskite nanocrystal-based light emitting diodes, and the positive effect of various surface treatments on external quantum efficiencies. We also discuss the current state-of-the-art in the surface chemistry of 1-D nanowires and 2-D nanoplatelets of CsPbBr 3 , which are more quantum confined than the corresponding cuboidal nanocrystals but also generally possess a higher defect density because of their increased surface area-to-volume ratios.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Structural Tolerance of Zirconium Diboride under Electron Irradiation through in-situ Convergent Beam Electron Diffraction and Energy-dispersive X-ray Spectroscopy

Zirconium diboride (ZrB 2 ) is a ultra-high temperature ceramic with high melting temperature (>3000 K), super strength and hardness, good thermal conductivity, and excellent resistance to plasma erosion and chemical erosion, being widely applied in hypersonic flight, arc-electrodes, refractory materials, and plasma-facing materials in fusion reactors. Therefore, the structural stability of the material is essential for the applications. Up to now, the material was investigated under neutron irradiation and high-energy ion irradiations. It was reported that the neutron irradiation caused swelling and catastrophic cracking. High-energy ions (30 keV He + ) changed the surface morphology and caused the bright blue and brown colors on ZrB 2 surfaces between 920 K and 1120 K. The electron irradiation tolerance of the material has not been reported yet. Here we used convergent beam electron diffraction (CBED) and energy-dispersive X-ray spectroscopy (EDS) to investigate structural tolerances of ZrB 2 crystals under high-energy electrons at room temperature under vacuum. Finally, the investigation would benefit the understanding of its structural tolerance at microscales.

42 ENGINEERING↗
DOE OSTI2025

Time-Domain Extreme-Ultraviolet Diffuse Scattering Spectroscopy of Nanoscale Surface Phonons

Here, we report the observation of dynamic fringe patterns in the diffuse scattering of extreme ultraviolet light from surfaces, following femtosecond optical excitation. At each point on the detector, the diffuse scattering intensity exhibits oscillations at well-defined frequencies that correspond to surface phonons with wave vectors determined by the scattering geometry, indicating that the optical excitation generates coherent surface phonons propagating in all directions and spanning a wavelength range from 60 to 300 nm. This phenomenon is observed on a variety of samples, including single-layer and multilayer metal films, as well as bulk semiconductors. The measured surface phonon dispersions show good agreement with theoretical calculations. By comparing signal amplitudes from samples with different surface morphologies, we find that the excitation mechanism is linked to the natural surface roughness of the samples. However, the signal is still detectable on extremely smooth surfaces with subnanometer roughness. Our findings demonstrate a simple and effective method for optically exciting coherent surface phonons with nanoscale wavelengths on a wide range of solid samples and establish a foundation for surface phonon spectroscopy in a wave vector range well beyond the limit of conventional surface Brillouin scattering.

Capotondi, F. [Elettra-Sincrotrone Trieste (Italy)↗
DOE OSTI2022

Adhesively-bonded Metal-CFRTP Bi-materials: Enhanced Crack Growth Resistance via Plasma and Quantified Fracture via Size Effect Method

This work investigated air plasma effect on the Mode I crack growth resistance of adhesively-bonded metal-CFRTP dissimilar joints by using aluminum alloy (AA6061) and short-carbon-fiber-reinforced polyamide 66 (CFRPA66) as an example, and the Double Cantilever Beam (DCB) fracture testing as an evaluation method. The results show that air plasma treatment can significantly improve the fracture resistance of adhesively-bonded AA6061-CFRPA66 dissimilar joints with about 140% enhanced Mode I fracture energy in maximum compared to non-treated ones. The quantified fracture energies from size effect method for both non-treated and plasma-treated cases are geometry-independent, whereas this is not true for modified beam theory causing geometry-dependent results. The foregoing improvement was confirmed from the failure surface morphology of plasma-treated specimens, showing fibers peeling off from CFRPA66 surface due to plasma-enhanced bonding between CFRPA66 and adhesive by the formation of covalent bonds at their interface. This study demonstrated air plasma as an efficient surface modification method to enhance the fracture resistance of adhesively-bonded metal-CFRTP dissimilar joints, and size effect method as a characterization method to properly quantify their fracture properties. These aspects are valuable in the area of multi-materials joining.

Plasma, Adhesive Bonding, Slow Crack Growth, fract↗
NASA NTRS1980

A fundamental approach to adhesion: Synthesis, surface analysis, thermodynamics and mechanics

Several techniques were used to study pretreated Ti 6-4 surfaces including scanning electron microscopy (SEM), electron spectroscopy of chemical analysis (ESCA), and, reflectance visible spectroscopy. Each pretreatment type gave a characteristic surface morphology as seen by SEM. Elemental analysis of the Ti 6-4 surfaces was done using ESCA. Trace residual contaminants from particular chemical pretreatments were identified readily. Results indicate that reflectance visible spectroscopy using indicator dyes placed on Ti 6-4 surfaces appears to be a feasible approach to establish surface acidity. Differences in surface acidity were observed using bromthymol blue on Ti 6-4 surfaces pretreated by two different methods.

Beck, B.↗
NASA NTRS1980

Spectroscopic characterization of titanium 6-4 surfaces after chemical pretreatments

Several techniques have been used to study pretreated Ti 6-4 surfaces including scanning electron microscopy (SEM), electron spectroscopy of chemical analysis (ESCA), and, reflectance visibile spectroscopy. Each pretreatment type gives a characteristic surface morphology as seen by SEM. Elemental analysis of the Ti 6-4 surfaces was done using ESCA. Trace residual contaminants from particular chemical pretreatments are identified readily. Reflectance visible spectroscopy using indicator dyes placed on Ti 6-4 surfaces appears to be a feasible approach to establish surface acidity. Differences in surface acidity have been observed using bromthymol blue on Ti 6-4 surfaces pretreated by two different methods.

Chen, W.↗
NASA NTRS1995

Influence of Two-Phase Thermocapillary Flow on Liquid Retention in Microscopic Pores

An important feature of screened propellant acquisition devices is the retention capability or maximum maintainable pressure difference across the porous barrier separating the liquid and gas. Previous experiments with liquid hydrogen showed a marked reduction in retention when the tank containing the device was pressurized with hydrogen vapor. These tests, however did not indicate any appreciable degradation in retention with helium pressurization or direct heating through the screen. The objective of this article is to determine if the thermocapillary convection arising from phase change in the microscopic pores of such screens could cause these disparities in performance. A numerical model of flow in a single pore suggests that the thermocapillary-induced gradient in liquid pressure along the surface can strongly affect surface morphology. In an evaporative environment, this gradient exerts a stabilizing influence on surface curvature, and preserves the momentum balance between the liquid and gas. With condensation, it causes a force imbalance and a destabilizing suction in the middle of the pore that reduces retention. Results also indicate that introducing an inert gas, such as helium, suppresses this retention loss mechanism by lowering thermocapillary circulation and its associated interfacial pressure gradient.

Schmidt, George R.↗
DOE OSTI2023

Surface grain refinement of casting A380 aluminum alloy by ultrasonic-assisted surface mechanical grinding treatment

A novel surface processing technique, ultrasonic-assisted surface mechnical grinding treatment (U-SMGT), was proposed and applied to modify the surface micriostructure of the casting aluminum alloy (A380). Comprehensive post-process chracterization techniques including 3D profilometry, optical microscope, scanning electric microscopy (SEM), and electron backscatter diffraction (EBSD) were carried out to investigate the surface morphology and microstructure of the processed region (PR). It was found that a surface layer of grain refinement with a thickness of about 50 µm was formed. In the as-received base material (BM), large clusters of dendritic eutectic phase with a size of approximately 20 µm were isolated by α-Al matrix. Nano-indentation tests showed that hardness of the eutectic and α-Al in the as-received BM was 2.15 GPa and 1.2 GPa respectively. After U-SMGT, the large dendritic eutectic phase was broken down into much fine particles with an average size of 0.57 µm. These fine particles were uniformly distributed into the α-Al matrix. Nano-indentation measurement exhibited a hardness of 2.27 GPa within the processed region. The overall high hardness in the processed region is a result of the pinning effect of uniformly distributed fine dendrites and grain refinement of Al-matrix.

36 MATERIALS SCIENCE↗