Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “strain hardening”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

High strain-rate compression behavior of polymeric rod and plate Kelvin lattice structures

The compressive high strain-rate behavior of polymeric Kelvin lattice structures with rod-based or plate-based unit cells was investigated through experimental techniques and finite element simulations. Polymeric lattice structures with 5x5x5 unit cell geometries were manufactured on the millimeter scale using vat polymerization additive manufacturing and tested at low (0.001/s) and high (1000/s) strain-rates. High strain-rate experiments were performed and validated for a viscoelastic split-Hopkinson (Kolsky) pressure bar system (SHPB) coupled with high-speed imaging and digital image correlation (DIC). Experimental results at both low and high strain-rates show the formation of a localized deformation band which was more prevalent in low relative density specimens and low strain-rate experiments. Strain-rate effects of lattice specimens strongly correlate with effects of the base polymer material; both bulk polymer and lattice specimen demonstrated strain-rate hardening, strain-rate stiffening, and decreased fracture strain under dynamic loading. Results show mechanical failure properties and energy absorption depended strongly on the relative density of the lattice specimen and exhibited distinct scaling between relative density and geometry type (rod, plate) and loading rate. High relative density plate-lattices demonstrated inferior mechanical properties to rod-lattices; however, there exists a critical relative density for a given mechanical property (17%- 28%) below which plate-lattices outperform rod-lattices of similar mass. As a result, high strain-rate explicit finite element simulations were performed and showed good agreement with the mechanical failure trends and deformation modes observed in the experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Cryogenic mechanical behaviors of CrMnFeCoNi high-entropy alloy

The CrMnFeCoNi high-entropy alloy (HEA) exhibits higher yield strength, ultimate strength and ductility at lower temperature. To further clarify the effect of the testing temperature on microstructure evolution, in this study in-situ synchrotron-based high-energy X-ray diffraction tensile tests were carried out from 298 K down to 123 K. The enhanced yield strength of the alloy at cryogenic temperatures can be attributed to the greater lattice distortion prior to plastic deformation. Higher strain hardening rate leads to the simultaneously enhanced strength and ductility of the studied HEA below room temperature. Both dynamic Hall-Petch hardening (twinning) and dislocation hardening provide high work hardening capacity for this alloy during the plastic deformation at cryogenic temperatures. The increased dislocation density and nano-twins at cryogenic temperatures can be attributed to the decrease in the stacking fault energy as the deformation temperature decreases. These studies could provide an in-depth understanding for the strengthening mechanisms of the HEA in different temperature conditions and guide the exploration of HEAs with superb mechanical properties at cryogenic environments.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In situ investigation of the deformation behaviors of Fe 20 Co 30 Cr 25 Ni 25 and Fe 20 Co 30 Cr 30 Ni 20 high entropy alloys by high-energy X-ray diffraction

In situ synchrotron-based high-energy X-ray diffraction (HE-XRD) technique was employed to investigate the mechanical behaviors and microstructural evolution of face-centered cubic (FCC) Fe 20 Co 30 Cr 25 Ni 25 and Fe 20 Co 30 Cr 30 Ni 20 high entropy alloys (HEAs) during tensile deformation. Fe 20 Co 30 Cr 30 Ni 20 HEA has a good combination of strength (ultimate tensile strength of 864 ± 35 MPa) and ductility (elongation of 0.627 ± 0.021). The HE-XRD investigation reveals that Fe 20 Co 30 Cr 30 Ni 20 HEA has the transformation-induced plasticity (TRIP) effect, which starts at a critical stress of ~555 MPa. Furthermore, transmission electron microscopy confirmed this deformation-induced new phase is hexagonal-close-packed structured ε-martensite, which follows an orientation relationship of {111} γ //(0001) ε , and (110) γ //[11 2 ¯ 0] ε with the FCC γ matrix. The observation of deformation twins in the deformed samples of the two studied HEAs proves that twinning-induced plasticity (TWIP) effect occurs in both HEAs. The combination of TRIP and TWIP effects lead to the high strength, large ductility and improved strain hardening behavior of Fe 20 Co 30 Cr 30 Ni 20 HEA.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In situ indentation and high cycle tapping deformation responses in a nanolaminate crystalline/amorphous metal composite

The incorporation of nanostructured and amorphous metals into modern applications is reliant on the understanding of deformation and failure modes in constrained conditions. To study this, a 105 nm crystalline Cu/160 nm amorphous Cu 45 Zr 55 (at.%) multilayer structure was fabricated with the two crystalline layers sputter deposited between the top-middle-bottom amorphous layers and prepared to electron transparency. The multilayer was then in situ indented either under a single load to a depth of ~ 100 nm (max load of ~ 100 μN) or held at 20 μN and then repeatedly indented with an additional 5 μN up to 20,000 cycles in a transmission electron microscope to compare the deformation responses in the nanolaminate. For the single indentation test, the multilayer showed serrated load-displacement behavior upon initial indentation inductive of shear banding. Additionally, at an indentation depth of ~ 32 nm, the multilayer exhibited perfect plastic behavior and no strain hardening. Both indented and fatigue-indented films revealed diffraction contrast changes with deformation. Subsequent Automated Crystal Orientation Mapping (ACOM) measurements confirmed and quantified global texture changes in the crystalline layers with specifically identified grains revealing rotation. Using a finite element model, the in-plane displacement vectors under the indent mapped conditions where ACOM determined grain rotation was observed, indicating the stress flow induced grain rotation. Furthermore, the single indented Cu layers also exhibited evidence of deformation induced grain growth, which was not evident in the fatigue-indented Cu based multilayer. Finally, the single indented multilayer retained a significant plastic crater in the upper most amorphous layer that directly contacted the indenter; a negligible crater impression in the same region was observed in the fatigued tested multilayer. These differences are explained by the different loading methods, applied load, and deformation mechanisms experienced in the multilayers.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Hierarchical microstructures and deformation behavior of laser direct-metal-deposited Cu–Fe alloys

Cu25Fe75 and Cu50Fe50 (nominal composition, at. %) alloys were fabricated using laser direct metal deposition (DMD) based additive manufacturing technique. These alloys exhibit hierarchical microstructures with bi-phasic Cu and Fe dendrites that contain nanoscale precipitates of varying sizes and structures. In the Cu25Fe75 alloy, Fe dendrites contained nanoscale, coherent, metastable BCC Cu and semi-coherent FCC Cu precipitates while the Cu matrix had nanoscale, coherent, metastable FCC Fe precipitates. In the Cu50Fe50 alloy, Fe dendrites only contained nanoscale semi-coherent FCC Cu precipitates while the Cu matrix had nanoscale coherent metastable FCC Fe precipitates. Both alloys exhibited enhanced flow strengths in the range of 750 – 980 MPa and significant plasticity, in compression. Here, the Cu25Fe75 alloy had lower yield strength than Cu50Fe50 alloy but higher maximum compressive strength due to higher strain hardening resulting from slightly coarser dendrites with hierarchy of nanoscale precipitation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The mechanism of twin thickening and the elastic strain state of TWIP steel nanotwins

A Twinning Induced Plasticity (TWIP) steel with a nominal composition of Fe-16.4Mn-0.9C-0.5Si-0.05Nb-0.05V was deformed to an engineering strain of 6%. The strain around the deformation twins were mapped using the 4D-STEM technique. Strain mapping showed a large average elastic strain of approximately 6% in the directions parallel and perpendicular to the twinning direction. However, the large average strain comprised of several hot spots of even larger strains of up to 12%. These hot spots could be attributed to a high density of sessile Frank dislocations on the twin boundary and correspond to shear stresses of 1–1.5 GPa. The strain and therefore stress fields are significantly larger than other materials known to twin and are speculated to be responsible for the early thickness saturation of TWIP steel nanotwins. The ability to keep twins extremely thin helps improve grain fragmentation, i.e. the dynamic Hall–Petch effect, and underpins the large elongations and strain hardening rates in TWIP steels.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural refinement of an Al-Ce-Mg alloy via Shear Assisted Processing and Extrusion

Al-Ce alloys have attracted recent interest because of their high thermal stability due to the low solubility of Ce in the Al matrix. The Al 11 Ce 3 eutectic phase gives excellent strain hardening behavior and moderate high-temperature strength in the as-cast state. However, its strengthening effect is limited by its coarse as-cast structure. Therefore, alternative manufacturing methods such as additive manufacturing or equal channel angular pressing have been applied to refine the Al 11 Ce 3 phase to good effect. However, these techniques are both expensive and time-consuming. Therefore, this study aims to use Shear Assisted Processing and Extrusion (ShAPE), an emerging solid phase processing technique that is more easily scalable than the previously mentioned methods. ShAPE can produce useful cross-sections of an Al-8Ce-4Mg alloy while refining the Al 11 Ce 3 phase to produce a higher strength material. It was found that a low temperature ShAPE process can improve the room temperature yield strength by ~60 % compared to a binary Al-4Mg alloy. Additionally, the high-temperature yield strength of the Al-Ce alloys increased by 20%, with a simultaneous 15% improvement in ductility compared to the binary Al-Mg alloy. Finally, these results highlight the potential for ShAPE as a processing technique for Al-Ce alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Understanding the deformation behavior of the γ rich transformative Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 complex concentrated alloy using in situ synchrotron diffraction

In situ tensile testing coupled with synchrotron x-ray diffraction was used to study the deformation behavior of metastability-engineered Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 complex concentrated alloy. Monitoring the evolution of phase fraction and strain hardening response allowed the determination of true critical stress for the onset of the transformation-induced plasticity (TRIP) to be ∼375 MPa, preceded by slip starting at ∼255 MPa. In situ EBSD was used to validate the critical stress for transformation at the microstructure level and observe slip traces to confirm prior slip activity before the transformation. Further, a modeling framework based on stacking fault energy (SFE) was developed to predict the critical stress for transformation. Modeling suggested the SFE of the alloy to fall nearly 15 mJ/m 2 , which agrees well with SFE values calculated using synchrotron peak shifting (12 mJ/m 2 ) and thermodynamic calculation (11 mJ/m 2 ). As a result of γ-fcc to ε-hcp phase transformation, new {0002} ε planes emerged parallel to unaligned {111} γ planes with the tensile loading following S-N orientation relationship. Such selective emergence of new diffraction rings corresponding to ε phase is understood based on the reorientation of γ crystals with reference to tensile axis. In conclusion, this approach can be extended to effectively design alloys based on critical stress required for activating different deformation mechanisms to further push the limits of the strength-ductility envelope.

Complex concentrated alloy↗
DOE OSTI2026

Microstructural evolution, defect mitigation, and precipitation behavior in AA6061 via laser powder bed fusion with high-temperature substrate heating

Defects, particularly solidification cracking, remain persistent challenges in the laser powder bed fusion (LPBF) processing of AA6061 aluminum alloy. This study systematically investigates defect mitigation, microstructural evolution, and mechanical properties associated with high-temperature substrate preheating at 500 °C. Comprehensive microstructural analyses, including characterization of defects, grain structures, and precipitation behavior, were performed on samples in both as-built and T6 heat-treated states. Elevated preheating substantially reduced solidification cracking across a wide processing window, while demonstrating decreased crack sensitivity to laser parameters. Columnar cracks along the build direction were observed despite substrate preheating. Lack-of-fusion and keyhole porosity were effectively eliminated, though gas-induced microporosity persisted at higher powers. In-depth characterization of two distinct laser power and speed conditions confirmed the formation of micron-sized, non-coherent Mg 2 Si precipitates under heated substrate conditions, alongside α-AlFeCrMnSi intermetallic phases indicative of in-situ thermal effects during fabrication. Subsequent T6 heat treatment revealed the formation of fine, coherent needle-shaped β″ strengthening precipitates. Despite substantial differences in processing parameters, comparable mechanical properties were measured in the as-built samples (∼52 MPa yield strength, ∼130 MPa tensile strength), primarily due to reduced strain hardening effects and consistent precipitation characteristics. Meanwhile, the T6 heat treatment led to significant improvement in properties, enhancing yield strength by over 400%, aligning closely with the performance of conventional wrought AA6061-T6. These findings underscore that high-temperature substrate preheating offers an effective means to suppress cracks, control precipitation, and enhance mechanical performance in LPBF-processed AA6061.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Deformation behavior of metallic glass composites and plasticity accommodation at microstructural length-scales

Bulk metallic glass matrix composites represent a unique microstructural design strategy for overcoming the strength/ductility trade-off in structural alloys. Site-specific mechanical behavior of a Ti-based bulk metallic glass composite was evaluated at microstructural length-scale. The micro-pillars on the amorphous matrix showed on average a yield point of 1.9 GPa followed by serrated plastic deformation characteristic of shear banding. In contrast, micro-pillars on the crystalline dendritic phase showed a much lower yield strength of 0.72 GPa on average for the four different crystallographic orientations chosen, smooth plastic flow with no recognizable load burst, and stable strain-hardening after yield point. A number of micro-pillars were made at the interface between the glassy matrix and the crystalline dendrite. The mixed micro-pillars showed homogeneous deformation and greater plasticity which was attributed to their smaller stored elastic energy. Shear bands initiated in the amorphous matrix were arrested by the crystalline dendrite, which accommodated plasticity through slip bands and dislocations pile-ups. The interface remained intact after plastic deformation, with no observable signs of devitrification in the amorphous phase.

Bulk metallic glass matrix composite, Micro-pillar↗
DOE OSTI2022

Comparison of cracking behavior of nanocrystalline Cu film on substrates of different plastic deformation mechanisms

Nanocrystalline (NC) metallic thin films on metal substrates usually undergo substantial cracking at applied strains of a few percent due to strain concentration at the film/substrate interfaces. In this work, we show that the cracking of a nanocrystalline Cu film can be significantly inhibited by a NiTi substrate. NC Cu films are deposited on 304 stainless steel, Kapton and NiTi substrates, in which plastic deformation occurs via dislocation slip, molecule chain disentanglement and collective lattice shear, respectively. NC Cu film on NiTi substrate starts to show observable cracks at an applied strain of 24%, in contrast to 6% for that on steel and 15% for that on Kapton. Further, the crack density in the film on NiTi substrate is two to three orders lower than the counterparts. The discrepancy is suggested to attribute to the reduced local strain concentration enabled by the uniform lattice shear and high strain hardening of the NiTi substrate.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Additive manufacturing of three-dimensional (3D)-architected CoCrFeNiMn high- entropy alloy with great energy absorption

In this study, we developed an approach to additive manufacturing of three-dimensional (3D)-architected CoCrFeNiMn high-entropy alloys by direct ink writing combined with thermal sintering. The 3D-architected CoCrFeNiMn lattices exhibit the outstanding energy absorption capacity that expands the envelope of existing architected materials. Such a high-energy absorption ability originates from the bend-dominated deformation mode of the 3D-architecture as well as the fully-annealed homogeneous microstructure of equiaxed grains, which collectively lead to remarkable strain hardening upon deformation. Our study provides a new avenue for 3D-printing advanced architected materials with extreme mechanical energy absorption for a myriad of structural applications.

mechanical property↗
DOE OSTI2022

Dislocation-θ' (Al2Cu) interactions during creep deformation of an Al-Cu alloy

While precipitate-dislocation interactions are well-understood for Al-Cu alloys in tension, creep behavior has seen far less study. New, thermally-stabilized Al-Cu alloys have θ' (Al 2 Cu) as strengthening precipitates that remain stable up to 300 °C (~60% of the melting temperature) and higher, where creep becomes essential to the mechanical behavior. This investigation identifies the precipitate-dislocation interactions in such an Al-Cu alloy using in-situ neutron diffraction and scanning transmission electron microscopy. Significant load transfer to the θ' precipitates occurs, which can be attributed to dislocation loops on the interfaces of θ' and the Al matrix. Thus, Orowan looping is identified to be the primary activity for precipitate-dislocation interactions. As Orowan looping and load transfer are associated with significant strain hardening, these results explain the excellent creep resistance seen in this alloy, and provide insights into the design of precipitation strengthened alloys with superior creep performance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Elucidating Polymer Binder Entanglement in Freestanding Sulfide Solid-State Electrolyte Membranes

This study advances the development of flexible, sheet-type sulfide solid-state electrolytes (SSEs) for use in all-solid-state batteries, emphasizing the important and previously insufficiently investigated role of polymer binder entanglement. Here, the molecular weight of polymer binders is pivotal in crafting robust, freestanding SSE films. Our research uncovers a dual impact: higher molecular weight binders bolster the structural integrity of SSE films but elevate grain boundary resistance and diminish critical current density, whereas lower molecular weight poly(isobutylene) films, despite their more uniform distribution, lack the essential strain hardening or strength for sustained active material contact. Crucially, full cells employing higher molecular weight binders demonstrate improved discharge capacity retention, contrasting sharply with the notable capacity degradation in lower molecular weight cells. Our findings not only deepen the comprehension of binder influences in solid-state batteries but also chart a course for refining all-solid-state battery technologies, a key stride for the future of energy storage solutions.

25 ENERGY STORAGE↗
DOE OSTI2025

Intermediate States Enable Keratin-like α-To-β Transformations in Strain-Responsive Synthetic Polypeptides

Nature’s fibrous proteins, such as α-keratin, achieve remarkable mechanical properties by undergoing strain-induced α-to-β conformational transitions. Inspired by these materials, we report a strategy for designing synthetic polypeptides that undergo similar transformations at elevated temperatures far exceeding keratin’s operational range. By employing helix-confined ring-opening polymerization (ROP) of N -carboxyanhydrides (NCAs) initiated by a short poly(γ-benzyl- L -glutamate) (PBLG) precursor, we synthesized poly( O -benzyl- L -serine) (PBLS) chains that adopt an α-helical structure yet transition into β-sheets upon heating. Compression molding at carefully chosen temperatures drives PBLS segments into an α-β intermediate state, characterized by relaxed intrachain hydrogen bonds and a hexagonal packing arrangement. Under mechanical strain, these intermediate states convert in situ into β-sheets, producing significant strain-hardening well below the spontaneous α-to-β temperature threshold. Further, this approach extends to polypeptides bearing different side chains, such as poly(S-benzyl- L -cysteine), demonstrating robust mechanical reinforcement across a wide temperature window up to ∼ 200 °C. In situ synchrotron X-ray analysis confirms that chain alignment, β-sheet formation, and domain growth occur stepwise during deformation. By harnessing the intermediate states and the supramolecular cooperativity conferred by compression-molded films, our method provides a versatile platform for developing next-generation polypeptide materials with tunable mechanical resilience and responsiveness─surpassing the temperature limitations of natural fibrous proteins and enabling potential applications demanding broad-temperature mechanical adaptability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Dislocation interactions in olivine control postseismic creep of the upper mantle

Changes in stress applied to mantle rocks, such as those imposed by earthquakes, commonly induce a period of transient creep, which is often modelled based on stress transfer among slip systems due to grain interactions. However, recent experiments have demonstrated that the accumulation of stresses among dislocations is the dominant cause of strain hardening in olivine at temperatures ≤600 °C, raising the question of whether the same process contributes to transient creep at higher temperatures. Here, we demonstrate that olivine samples deformed at 25 °C or 1150–1250 °C both preserve stress heterogeneities of ~1 GPa that are imparted by dislocations and have correlation lengths of ~1 μm. The similar stress distributions formed at these different temperatures indicate that accumulation of stresses among dislocations also provides a contribution to transient creep at high temperatures. The results motivate a new generation of models that capture these intragranular processes and may refine predictions of evolving mantle viscosity over the earthquake cycle.

58 GEOSCIENCES↗
DOE OSTI2021

Elimination of oxygen sensitivity in α-titanium by substitutional alloying with Al

Individually, increasing the concentration of either oxygen or aluminum has a deleterious effect on the ductility of titanium alloys. For example, extremely small amounts of interstitial oxygen can severely deteriorate the tensile ductility of titanium, particularly at cryogenic temperatures. Likewise, substitutional aluminum will decrease the ductility of titanium at low-oxygen concentrations. Here, we demonstrate that, counter-intuitively, significant additions of both Al and O substantially improves both strength and ductility, with a 6-fold increase in ductility for a Ti-6Al-0.3 O alloy as compared to a Ti-0.3 O alloy. The Al and O solutes act together to increase and sustain a high strain-hardening rate by modifying the planar slip that predominates into a delocalized, three-dimensional dislocation pattern. Furthermore, the mechanism can be attributed to decreasing stacking fault energy by Al, modification of the “shuffle” mechanism of oxygen-dislocation interaction by the repulsive Al-O interaction in Ti, and micro-segregation of Al and O by the same cause.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Grain refinement in titanium prevents low temperature oxygen embrittlement

Interstitial oxygen embrittles titanium, particularly at cryogenic temperatures, which necessitates a stringent control of oxygen content in fabricating titanium and its alloys. Here, we propose a structural strategy, via grain refinement, to alleviate this problem. Compared to a coarse-grained counterpart that is extremely brittle at 77 K, the uniform elongation of an ultrafine-grained (UFG) microstructure (grain size ~ 2.0 µm) in Ti-0.3wt.%O is successfully increased by an order of magnitude, maintaining an ultrahigh yield strength inherent to the UFG microstructure. This unique strength-ductility synergy in UFG Ti-0.3wt.%O is achieved via the combined effects of diluted grain boundary segregation of oxygen that helps to improve the grain boundary cohesive energy and enhanced dislocation activities that contribute to the excellent strain hardening ability. The present strategy will not only boost the potential applications of high strength Ti-O alloys at low temperatures, but can also be applied to other alloy systems, where interstitial solution hardening results into an undesirable loss of ductility.

36 MATERIALS SCIENCE↗