Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid solution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Combining XRD and Raman spectroscopy techniques to probe the solid solution and composite forms of Pb1-xCoxTiO3 systems

Highlights: • Pb{sub 1-x}Co{sub x}TiO{sub 3} system was produced by solid state reaction. • Co concentration determines the formation of solid solution or composite. • The atomic substitutions directly affect the Curie temperature. - Abstract: Raman scattering and XRD data allied to Rietveld refinement were used to investigate the structural and vibrational properties of Pb{sub 1-x}Co{sub x}TiO{sub 3} samples with x ranging from 0.0 to 1.0. The results showed reductions in the tetragonallity factor and in the wavenumber of E(1TO) soft mode in the interval between x = 0.0 (c/a = 1.063 and E(1TO) = 89 cm{sup −1}) and x = 0.2 (c/a = 1.042 and E(1TO) = 81 cm{sup −1}). These parameters present a partial recovery for x > 0.4. Quantitative phase analyses combined with SEM indicate the formation of a solid solution for x less than 0.2 and composite formation of PbTiO{sub 3} and CoTiO{sub 3} for x higher than 0.2. From the temperature-induced softening of the E(1TO) mode, it was investigated the effect of the atomic substitution on the PbTiO{sub 3} Curie temperature, showing a minimum at 720 K (x ∼ 0.4) compared to 763 K (x = 0).

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

Molecular beam epitaxy of III-P{sub x}As{sub 1−x} solid solutions: Mechanism of composition formation in the sublattice of a group V element

The effect of substrate temperature, As{sub 2} and P{sub 2} molecular flux densities, and growth rate on the composition of III-P{sub x}As{sub 1−x} solid solution layers prepared by molecular beam epitaxy is experimentally investigated. Experimental data in a wide range of growth conditions are analyzed. The results obtained are presented in the form of a kinetic model for describing the process of formation of the composition in the Group V sublattice of the III-P{sub x}As{sub 1−x} solid solution upon molecular beam epitaxy. The model can be used for choosing the growth conditions of the III-P{sub x}As{sub 1−x} (001) solid-solution layers of a specified composition.

36 MATERIALS SCIENCE↗
NASA NTRS1977

Pressureless sintered beta-prime-Si3N4 solid solution - Fabrication, microstructure, and strength

Pressureless sintering of beta-prime-Si3N4 solid solution was studied as a function of temperature using Si3N4, A1N, and Al2O3 as basic constituents. Y2O3-SiO2 additions were used to promote liquid-phase sintering. The sintered specimens were characterized with respect to density, microstructure, strength, oxidation, and thermal shock resistance. Density greater than 98 percent of theoretical was achieved by pressureless sintering at 1750 C. The microstructure consisted essentially of fine-grained beta-prime-Si3N4 solid solution as the major phase. Modulus of rupture strengths up to 483 M Pa were achieved at moderate temperature (1000 C), but decreased to 228 M Pa at 1380 C. This substantial strength loss was attributed to a 'glassy' grain boundary phase formed during cooling from the sintering temperature. The best oxidation resistance was exhibited by a composition containing 3 mol % Y2O3-SiO2 additives. Water quench thermal shock resistance was equivalent to that of reaction sintered silicon nitride but lower than hot-pressed silicon nitride.

Dutta, S.↗
DOE OSTI2019

Thermoelectric Properties of Nanocomposite Bi{sub 0.45}Sb{sub 1.55}Te{sub 2.985} Solid Solution with SiO{sub 2} Microparticles

Nanocomposite thermoelectrics based on Bi{sub 0.45}Sb{sub 1.55}Te{sub 2.985} solid solution of p-type conductivity are fabricated by the hot pressing of nanopowders of this solid solution with the addition of SiO{sub 2} microparticles. Investigations of the thermoelectric properties show that the thermoelectric power of the nanocomposites increases in a wide temperature range of 80–420 K, while the thermal conductivity considerably decreases at 80–320 K, which, despite a decrease in the electrical conductivity, leads to an increase in the thermoelectric efficiency in the nanostructured material without the SiO{sub 2} addition by almost 50% (at 300 K). When adding SiO{sub 2}, the efficiency decreases. The initial thermoelectric fabricated without nanostructuring, in which the maximal thermoelectric figure of merit ZT = 1 at 390 K, is most efficient at temperatures above 350 K.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Prediction of defect properties in concentrated solid solutions using a Langmuir-like model

The alleged existence of sluggish diffusion in high-entropy alloys has drawn controversy. In high-entropy alloys and, in general, in all solids, transport properties are controlled by point defect concentration, which must be known before performing atomistic simulations to compute transport coefficients. In this work, we present a general Langmuir-like model for defect concentration in an arbitrarily complex solid solution and apply this model to generate expressions for concentrations of vacancies and small interstitial atoms. We then calculate the vacancy concentration as a function of temperature in the equiatomic CoNiCrFeMn and FeAl alloys with modified embedded-atom-method potentials for various chemical orderings, showing there is no clear correlation between vacancy thermodynamics and chemical ordering in the CoNiCrFeMn alloy, but clear systematic patterns for FeAl. We believe this is due to the high stability of disordered, random, and ordered intermetallic phases, respectively, in the CoNiCrFeMn and FeAl systems. Finally, this work provides future avenues to the prediction of thermal interstitials and vacancies in solid solutions, which is necessary for models of nonequilibrium behavior of solid solutions.

composition↗
DOE OSTI2025

Super-expansive thermo-reversible interstitial solid solution of nanocrystal superlattices with mesogens

Designing superlattices of nanocrystals to mimic and extend the properties of atomic crystals has been a long-standing motivation in materials chemistry. Interstitial solid solutions, such as steel, are well-studied atomic lattices in which mobile components move among the interstices. These materials exhibit unique properties, including reversible structural changes and phase transitions. Interstitial solid solutions possess unique dynamic structures and reversible responses, which motivate the creation of their colloidal equivalents. Here, in this study, we report a fully thermo-reversible colloidal interstitial solid solution by combining liquid crystals and nanocrystals functionalized with promesogenic ligands. Mesogen molecules fill and diffuse among the interstices of a superlattice, resulting in a super-large thermal expansivity. The approach uses a modular design of interparticle interactions, allowing control of interparticle distance, microstructure and transition between crystallographic forms.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2018

Design of high-strength refractory complex solid-solution alloys

Nickel-based superalloys and near-equiatomic high-entropy alloys containing molybdenum are known for higher temperature strength and corrosion resistance. Yet, complex solid-solution alloys offer a huge design space to tune for optimal properties at slightly reduced entropy. For refractory Mo-W-Ta-Ti-Zr, we showcase KKR electronic structure methods via the coherent-potential approximation to identify alloys over five-dimensional design space with improved mechanical properties and necessary global (formation enthalpy) and local (short-range order) stability. Deformation is modeled with classical molecular dynamic simulations, validated from our first-principle data. We predict complex solid-solution alloys of improved stability with greatly enhanced modulus of elasticity (3× at 300 K) over near-equiatomic cases, as validated experimentally, and with higher moduli above 500 K over commercial alloys (2.3× at 2000 K). We also show that optimal complex solid-solution alloys are not described well by classical potentials due to critical electronic effects.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of stacking fault energy on damage microstructure in ion-irradiated CoCrFeNiMn concentrated solid solution alloys

In order to understand the effect of stacking fault energy on microstructural evolution in concentrated solid solution alloys, Kr 2+ ion irradiation was performed for FCC-type CoCrFeNiMnx alloys. During Kr 2+ ion irradiation at 500 degrees C the formation of black dots, self-interstitial atom faulted loops and perfect loops were observed, but no observable voids were found in all the alloys. The comparison of microstructural evolution among CoCrFeNiMn x (x = 0.7, 1, 1.3) alloys revealed less faulted loop number density and size in CoCrFeNiMn 1.3 . The stacking fault energy of each alloy was investigated using the deformed CoCrFeNiMn x alloys, and it was revealed that CoCrFeNiMn 1.3 had the highest stacking fault energy, which is higher value than that of 316SS. From these results, it is suggested that FeCrNiMn-based concentrated solid solution alloys could be well-designed by controlling the stacking fault energy with optimized Mn concentration as one of high radiation resistance structure materials. (C) 2020 Elsevier B.V. All rights reserved.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tailoring grain growth and solid solution strengthening of single-phase CrCoNi medium-entropy alloys by solute selection

In the present study, we selected solutes to be added to the CrCoNi medium-entropy alloy (MEA) based on the mismatch of self-diffusion activation energy (SDQ) between the alloying elements and constituent elements of the matrix, and then investigated their grain growth behavior and mechanical properties. Mo and Al were selected as the solutes for investigation primarily because they have higher and lower SDQ, respectively, than those of the matrix elements; a secondary factor was their higher and lower shear modulus. Their concentrations were fixed at 3 at.% each because previous work had shown these compositions to be single-phase solid solutions with the face-centered cubic structure. Three alloys were produced by arc melting, casting, homogenizing, cold rolling and annealing at various temperatures and times to produce samples with different grain sizes. They were (a) the base alloy CrCoNi, (b) the base alloy plus 3 at.% Mo, and (c) the base alloy plus 3 at.% Al. The activation energies for grain growth of the CrCoNi, CrCoNi-3Mo and CrCoNi-3Al MEAs were found to be ~251, ~368 and ~219 kJ/mol, respectively, consistent with the notion that elements with higher SDQ (in this study Mo) retard grain growth (likely by a solute-drag effect), whereas those with lower values (Al) accelerate grain growth. The room-temperature tensile properties show that Mo increases the yield strength by ~40% but Al addition has a smaller strengthening effect consistent with their relative shear moduli. The yield strength as a function of grain size for the three singlephase MEAs follows the classical Hall-Petch relationship with much higher slopes (> 600 MPa μm -0.5 ) than traditional solid solutions. Furthermore, this work shows that the grain growth kinetics and solid solution strengthening of the CrCoNi MEA can be tuned by selecting solute elements that have appropriate diffusion and physical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Magnetic structures of FeTiO{sub 3}-Fe{sub 2}O{sub 3} solid solution thin films studied by soft X-ray magnetic circular dichroism and ab initio multiplet calculations

The solid solutions between ilmenite (FeTiO{sub 3}) and hematite (α-Fe{sub 2}O{sub 3}) have recently attracted considerable attention as a spintronic material due to their interesting magnetic and electrical properties. In this study, the electronic and magnetic structures of epitaxially grown 0.6FeTiO{sub 3}·0.4Fe{sub 2}O{sub 3} solid solution thin films were investigated by combining x-ray absorption near-edge structure (XANES), x-ray magnetic circular dichroism (XMCD) for two different crystallographic projections, and first-principles theoretical calculations. The Fe L-edge XANES and XMCD spectra reveal that Fe is in the mixed-valent Fe{sup 2+}–Fe{sup 3+} states while Fe{sup 2+} ions are mainly responsible for the magnetization. Moreover, the experimental Fe L-edge XANES and XMCD spectra change depending on the incident x-ray directions, and the theoretical spectra explain such spectral features. We also find a large orbital magnetic moment, which can originate the magnetic anisotropy of this system. On the other hand, although the valence state of Ti was interpreted to be 4+ from the Ti L-edge XANES, XMCD signals indicate that some electrons are present in the Ti-3d orbital, which are coupled antiparallel to the magnetic moment of Fe{sup 2+} ions.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Evaluation of solid solution formation between ThO2 and δ-Bi2O3 by molecular precursor route

Highlights: • Molecular precursor route for the solid solution evaluation of ThO{sub 2}-BiO{sub 1.5}. • Up to 60 mol % of Bi{sup 3+} could be dissolved in fluorite structured ThO{sub 2}. • Oxygen vacancies manifested as defect bands after Bi{sup 3+} incorporation. • Narrowing of direct band gap with increasing Bi{sup 3+} concentration. - Abstract: The high chelating ability of nitrilotriacetic acid has been advantageously utilized to prepare molecular precursors containing thorium and bismuth. This aided to determine the extent of solid solution formation between thoria and δ-Bi{sub 2}O{sub 3} in fluorite structure by calcining the precursors in air. Up to 60 atomic % of Bi{sup 3+} could be substituted for Th{sup 4+} in fluorite structure beyond which phase separation occurred. Slight increase in cubic lattice constant was observed with increasing bismuth content along with indication of increased tensile strain of lattice. Porous morphology and presence of bismuth in calcined samples were confirmed from SEM and EDX measurements. Defect bands emerged in the Raman spectra near 590 cm{sup −1} in addition to a fluorite band near 460 cm{sup −1} for the bismuth substituted samples. Intermediate energy states were formed by the substitution of Bi{sup 3+} for Th{sup 4+} arising possibly from oxygen vacancies and it resulted in narrowing of direct band gap.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Defect evolution in Ni and solid-solution alloys of NiFe and NiFeCoCr under ion irradiation at 16 and 300 K

Single-phase concentrated solid-solution alloys (SP-CSAs) have shown unique chemical complexity at the levels of electrons and atoms, and their defect evolution is expected to be different from conventional dilute alloys. Single crystals of Ni, NiFe and NiFeCoCr are chosen as model systems to understand the chemical complexity on defect formation and damage accumulation in SP-CSAs under ion irradiation. The high-quality crystals were irradiated at 16 and 300 K to different ion fluences, to form irradiated region with little to heavy damages. Additionally, the ion-induced damage was determined using Rutherford backscattering spectrometry technique along a channeling direction (RBS/C) and the level of lattice damage in irradiated Ni and SP-CSAs was quantified from Monte Carlo (MC) simulations. The results are interpreted using the Multi Step Damage Accumulation model to reveal material damage accumulation kinetics. Key findings of the study are that in case of room temperature irradiations the damage level measured for complex alloys at the highest irradiation fluence of 2 × 10 15 cm -2 (~3 dpa) is significantly higher than that obtained for pure nickel samples and suggest two-step damage accumulation process with a defect transformation taking place at a fluence of about 1.5 × 10 15 cm -2 . Furthermore, structural and damage kinetic differences clearly imply that, with increasing degree of chemical complexity and high solid-solution strengthening effects from Ni to NiFe and to NiFeCoCr, the enhanced lattice stiffness resists to randomization of atomic configurations and inhibits the growth of extended defects.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Conductivity, structure, and thermodynamics of Y 2 Ti 2 O 7 –Y 3 NbO 7 solid solutions

The defect fluorite yttrium niobate Y 3 NbO 7 and pyrochlore yttrium titanate Y 2 Ti 2 O 7 solid solutions have been synthesized via a solid state synthesis route. The resulting stoichiometry of the oxides is Y 2+x Ti 2-2x Nb x O 7 , where x = 0 to x = 1. All of the samples were single-phase; however, for those with a predominant fluorite phase, a small amount of additional pyrochlore phase was detected. The volume of the solid solution unit cells linearly increases with increase in yttrium niobate content. The water uptake increases with (x) and the protonic defect concentration reaches almost 4.5 × 10 -3 mol mol -1 at 300 °C. The calculated enthalpy of formation from oxides suggests strong stability for all of the compositions, with the values of enthalpy ranging from -84.6 to -114.3 kJ mol -1 . The total conductivity does not have a visible dependence on Y 3 NbO 7 content. For each compound, the total conductivity is higher in wet air. Interestingly, for samples where x < 0.5, the ratio of conductivity in hydrogen to air increases with increasing temperature, while for x > 0.5, the trend is the opposite.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Facile synthesis of high surface area nanostructured ceria-zirconia-yttria-lanthana solid solutions with the assistance of lauric acid and dodecylamine

Highlights: • High surface area nanostructured ceria-zirconia-yttria-lanthana solid solutions are synthesized by a facile method. • Hydrophobic surfaces are obtained with the addition of lauric acid and dodecylamine in the synthesis. • The introduced lauric acid and dodecylamine are chemically adsorbed onto the surface of materials through a coordination effect. • Excellent thermal stability are obtained in lauric acid and dodecylamine assisted materials. - Abstract: Co-precipitation combined with the assistance of lauric acid and dodecylamine was used to synthesize high surface area nanostructured ceria-zirconia-yttria-lanthana solid solutions (CZ-L and CZ-D). The promotion effects of lauric acid and dodecylamine were studied systematically by N{sub 2} adsorption-desorption, scanning electron microscopy (SEM), transmission electron microscopy (TEM), FT-IR and Raman analysis. After being thermal aged at 1100 °C for 4 h in air, CZ-L and CZ-D present high surface areas of 26 m{sup 2}/g and 16 m{sup 2}/g, respectively. The results indicate that the added lauric acid and dodecylamine are chemically adsorbed onto the surface of materials through coordination effect. The obtained hydrophobic surface could greatly decrease the amount of superficial adsorbed water on the material and significantly reduce the surface tension. The addition of lauric acid and dodecylamine could also effectively support the network structures of the material and resist the collapse of pores upon drying and calcination.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

Magnetic and Optical Properties of Au–Co Solid Solution and Phase-Separated Thin Films and Nanoparticles

The chemical composition and morphology of Au x Co 1–x thin films and nanoparticles are controlled via a combination of cosputtering, pulsed laser-induced dewetting (PLiD), and annealing, leading to tunable magnetic and optical properties. Regardless of chemical composition, the as-deposited thin films and as-PLiD nanoparticles are found to possess a face-centered cubic (FCC) Au x Co 1–x solid-solution crystal structure. Annealing results in large phase-separated grains of Au and Co in both the thin films and nanostructures for all chemical compositions. The magnetic and optical properties are characterized via vibrating sample magnetometry (VSM), ellipsometry, optical transmission spectroscopy, and electron energy loss spectroscopy (EELS). Despite the exceptionally high magnetic anisotropy inherent to Co, the presence of sufficient Au (72 atom %) in the Au x Co 1–x solid solution results in superparamagnetic thin films. Among the as-PLiD nanoparticle samples, an increased Co composition leads to a departure from traditional ferromagnetism in favor of wasp-waisted hysteresis caused by magnetic vortices. Phase separation resulting from annealing leads to ferromagnetism for all compositions in both the thin films and nanoparticles. The optical properties of Au x Co 1–x nanostructures are also largely influenced by the chemical morphology, where the Au x Co 1–x intermixed solid solution has significantly damped plasmonic performance relative to pure Au and comparable to pure Co. Phase separation greatly enhances the quality factor, optical absorption, and electron energy loss spectroscopy (EELS) signatures. The enhancement of the localized surface plasmon resonances (LSPRs) scales with the reduction in Co composition, despite EELS evidence that excitation of the Co portions of a nanoparticle can provide a similar, and in some instances enhanced, LSPR resonance compared to Au. This behavior, however, is seemingly limited to the LSPR dipole mode, while higher-order modes are greatly damped by a Co aloof position. As a result, this observed magneto-plasmonic functionality and tunability could be applicable in biomedicine, namely, cancer therapeutics.

annealing (metallurgy)↗
NASA NTRS1999

Magnetic Damping of Solid Solution Semiconductor Alloys

The objective of this study is to: (1) experimentally test the validity of the modeling predictions applicable to the magnetic damping of convective flows in electrically conductive melts as this applies to the bulk growth of solid solution semiconducting materials; and (2) assess the effectiveness of steady magnetic fields in reducing the fluid flows occurring in these materials during processing. To achieve the objectives of this investigation, we are carrying out a comprehensive program in the Bridgman and floating-zone configurations using the solid solution alloy system Ge-Si. This alloy system has been studied extensively in environments that have not simultaneously included both low gravity and an applied magnetic field. Also, all compositions have a high electrical conductivity, and the materials parameters permit reasonable growth rates. An important supporting investigation is determining the role, if any, that thermoelectromagnetic convection (TEMC) plays during growth of these materials in a magnetic field. TEMC has significant implications for the deployment of a Magnetic Damping Furnace in space. This effect will be especially important in solid solutions where the growth interface is, in general, neither isothermal nor isoconcentrational. It could be important in single melting point materials, also, if faceting takes place producing a non-isothermal interface. In conclusion, magnetic fields up to 5 Tesla are sufficient to eliminate time-dependent convection in silicon floating zones and possibly Bridgman growth of Ge-Si alloys. In both cases, steady convection appears to be more significant for mass transport than diffusion, even at 5 Tesla in the geometries used here. These results are corroborated in both growth configurations by calculations.

Szofran, Frank R.↗
DOE OSTI2025

Flux Synthesis of Lattice‐Engineered Rutile Solid Solutions for Acidic Oxygen Evolution

Developing efficient and stable electrocatalysts for the acidic oxygen evolution reaction (OER) is vital for advancing proton exchange membrane water electrolysis (PEMWE) technologies. Here, in this study, we report a flux synthesis of nitrogen-doped Ti–Ru rutile-type solid-solution oxides (M-TiRu 4 ) using molten NaNO 3 as the flux medium. The flux medium promotes the low-temperature conversion of TiN to rutile TiO 2 , while in situ-formed RuO 2 nanoparticles facilitate lattice templating and couple with interfacial ion migration, enabling the formation of homogeneous solid solutions with abundant lattice heterogeneity. Simultaneously, nitrogen atoms are stably incorporated into the lattice of solid solutions, inducing bandgap narrowing, which enhances electronic conductivity. The developed M-TiRu 4 catalyst exhibits exceptional acidic OER performance, delivering a low overpotential of 194 mV at 10 mA cm −2 , superior durability over 600 h, and a Ru mass activity 7.8 times that of commercial RuO 2 . At the device level, M-TiRu 4 enables PEMWE operation at 1.64 V @ 2 A cm −2 and maintains stable performance at 500 mA cm −2 for 200 h with a minimal degradation rate of 20 µV h −1 . This work demonstrates a robust approach for designing high-performance, durable acidic OER catalysts via synergistic lattice and electronic structure engineering, paving the way for next-generation water-splitting technologies.

Wang, Fan [Univ. of Tennessee, Knoxville, TN (Unit↗
DOE OSTI2014

Al and Zn Impurity Diffusion in Binary and Ternary Magnesium Solid-Solutions

Magnesium alloys are considered for implementation into structural components where energy-efficiency and light-weighting are important. Two of the most common alloying elements in magnesium alloys are Aluminum and Zinc. The present work examines impurity diffusion coefficients of Al and Zn in Mg(Zn) and Mg(Al) binary solid solutions, respectively. Experimental investigation is carried out with ternary diffusion couples with polycrystalline alloys. Concentration profiles were measured by electron microprobe micro-analysis and the impurity diffusion coefficients were determined by the Hall Method. Results of Al and Zn impurity diffusion in Mg solid solutions are reported, and examined as a function of composition of Mg solid solution.

aluminum↗