Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “resonator temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Demonstration of Microwave Cavity Transducer Performance in High Temperature Fluid Flow Sensing: Development of Microwave Cavity Flow Meter for Advanced Reactor High Temperature Fluids

We are investigating a microwave resonant cavity transducer for flow sensing in the vessel of a high temperature fluid advanced reactor (AR), such as a molten salt cooled reactor (MSCR) or a sodium fast reactor (SFR). This transducer is a hollow metallic cylindrical cavity, with one of the flat walls of the cylinder flexible enough to undergo microscopic deflection due to dynamic fluid pressure. Membrane deflection leads to a shift in the microwave resonant frequency, which can be detected with a spectrum analyzer. We have performed a preliminary proof-of-principle test of flow sensing in high temperature liquid sodium in environment, which is similar to that of an advanced reactor. The liquid sodium setup consists of a cylindrical vessel with a center feed line, where a transducer inserted through the top cap of the vessel measures velocity of the impinging liquid jet. For this test, we have developed a cylindrical resonator, which was machined from stainless steel 316 and electroplated with silver on the interior surfaces. Outer diameter of the cylindrical cavity is approximately 3cm, and the thin wall is approximately 200µm thick. We have also developed and insertion probe consisting of a 50cm WR-42 brass waveguide enclosed in a protective SS316 tube. The cavity was excited through a WR-42 waveguide through a subwavelength hole on the side of the wall of the cylinder in the TE 011 mode with resonant frequency f ≈ 17.8GHz. As a calibration experiment, we have assembled a water vessel with a center feed, and with dimensions similar to those of the liquid sodium setup. Frequency shift of the cavity spectral response was obtained at room temperature and ambient pressure by gradually increasing water flow rate from 0 to 25GPM (gallons per minute). Corresponding monotonic increase of resonant frequency by several hundred KHz was observed. Next, a sodium flow rate sensing study was performed in a liquid sodium vessel at 340° C temperature and ambient pressure. The flow rate was changed by varying sodium pump power, and a frequency shift of several hundred KHz was observed.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS2009

Measurement of the Dielectric Constant of Seawater at L-Band: Techniques and Measurements

Satellite instruments, that will monitor salinity from space in the near future, require an accurate relationship between salinity/temperature and seawater dielectric constant. This paper will review measurements that were made of the dielectric constant of seawater during the past several years. The objective of the measurements is to determine the dependence of the dielectric constant of seawater on salinity and on temperature, more accurately than in the past. by taking advantage of modem instrumentation. The measurements of seawater permittivity have been performed as a function of salinity and temperature using a transmission resonant cavity technique. The measurements have been made in the salinity range of 10 to 38 psu and in the temperature range of IOU C to 35 C. These results will be useful in algorithm development for sensor systems such as SMOS and Aquarius. The measurement system consists of a brass microwave cavity that is resonant at 1.413 GHz. The seawater is introduced into the cavity through a capillary glass tube having an inner diameter of 0.1 mm. The diameter of the tube has been made very small so that the amount of seawater introduced in the cavity is small - thus maintaining the sensitivity of the measurements and allowing the use of perturbation theory predicting the seawater permittivity. The change in resonant frequency and the change in cavity Q can be used to determine the real and imaginary pare of the dielectric constant of seawater introduced into the slender tube. The microwave measurements are made by an HPS722D network analyzer. The cavity has been immersed in a u~ateriethylene-glycol bath which is connected to a Lauda circulator. The circulator keeps the brass cavity at a temperature constant to within 0.01 degrees. The system is automated using a Visual Basic program to control the analyzer and to collect the data. The results of the dielectric constant measurements of seawater will be presented. The measurement results will be compared with permittivity values generated from the Kline and Swift relationship. Two methods of calibration will be discussed, The errors that each technique introduces into the measurement resulls will be reviewed. Temperature stability, frequency drift and the effect of increasing cavity transmission loss on the unloaded cavity Q will also be discussed.

Lang, R.↗
NASA NTRS2010

Temperature Dependence of Thin Film Spiral Inductors on Alumina Over a Temperature Range of 25 to 475 C

In this paper, we present an analysis of inductors on an Alumina substrate over the temperature range of 25 to 475 C. Five sets of inductors, each set consisting of a 1.5, 2.5, 3.5, and a 4.5 turn inductor with different line width and spacing, were measured on a high temperature probe station from 10 MHz to 30 GHz. From these measured characteristics, it is shown that the inductance is nearly independent of temperature for low frequencies compared to the self resonant frequency, the parasitic capacitances are independent of temperature, and the resistance varies nearly linearly with temperature. These characteristics result in the self resonant frequency decreasing by only a few percent as the temperature is increased from 25 to 475 C, but the maximum quality factor decreases by a factor of 2 to 3. These observations based on measured data are confirmed through 2D simulations using Sonnet software.

Ponchak, George E.↗
DOE OSTI2026

Observation of surface ferromagnons in the axion-insulating phase of the antiferromagnetic topological insulator EuSn 2⁢ As 2

We report the study of spin dynamics of Eu 2+ in the antiferromagnetic axion topological insulator EuSn 2 ⁢As 2 by means of antiferromagnetic resonance at 9.34 GHz. Below the Néel temperature (𝑇 N ), two types of resonance modes, the conventional bulk antiferromagnetic resonance and additional surface ferromagnetic resonance, are observed. The latter turns out to be characteristic of the axion-insulating phase. Above 𝑇 N , we prove the existence of a Kosterlitz-Thouless scenario that is relevant for the spin relaxation in the Eu 2+ layers. The absence of Korringa relaxation indicates the strong confinement of the conduction electrons at the Fermi level to the SnAs layers.

Antiferromagnets↗
NASA NTRS2009

Nonlinear Thermal Compensators for WGM Resonators

In an alternative version of a proposed bimaterial thermal compensator for a whispering-gallery-mode (WGM) optical resonator, a mechanical element having nonlinear stiffness would be added to enable stabilization of a desired resonance frequency at a suitable fixed working temperature. The previous version was described in "Bimaterial Thermal Compensators for WGM Resonators." Both versions are intended to serve as inexpensive means of preventing (to first order) or reducing temperature-related changes in resonance frequencies.

Savchenkov, Anatoliy↗
NASA NTRS1990

Bias and uncertainty in the absorption emission measurement of atomic sodium density in the SSME exit plane

The measurement of atomic sodium concentration in the TTB 019 firing of April 1990 is significant in that it represents the first measurement of density at the exit plane of the space shuttle main engine. The knowledge of the sodium density, combined with the certainty that the exit plane of the plume is optically thin at the sodium D-line wavelengths, provides essential information for evaluation of diagnostic techniques using sodium atoms, such as resonant Doppler velocimetry for temperature, pressure, and velocity through high resolution fluorescent lineshape analysis. The technique used for the sodium atom line transmission (SALT) measurements is that of resonant absorption emission using a hollow cathode lamp as the reference source. Through the use of two-dimensional kinetic (TDK) predictions of temperature and density for the flight engine case and radiative transfer calculations, this line-of-sight spectrally integrated transmission indicates a sodium atom concentration, i.e., mole fraction, of 0.91e-10. The subject of this paper is the assumptions and measurement uncertainties tied into the calculation. Because of the narrow shape of the source emission, the uncertainties in the absorption profile could introduce considerable bias in the measurement. The following were investigated: (1) the inclusion of hyperfine splitting of the D-lines in the calculation; (2) the use of the flight engine predictions of plume temperature and density versus those for the large throat engine; (3) the assumption of a Gaussian, i.e., Doppler, distribution for the source radiance with a temperature of 400 K; (4) the use of atomic collisional shift and width values for the work by Jongerius; and (5) a Doppler shift for a 7 degree outward velocity vector at the plume edge. Also included in the study was the bias introduced by an uncertainty in the measurement of the D1/D2 line ratio in the source.

Bauman, Leslie E.↗
NASA NTRS1990

Sequentially evaporated thin film YBa2Cu3O(7-x) superconducting microwave ring resonator

There is great interest in the application of thin film high temperature superconductors in high frequency electronic circuits. A ring resonator provides a good test vehicle for assessing the microwave losses in the superconductor and for comparing films made by different techniques. Ring resonators made of YBa2Cu3O(7-x) have been investigated on LaAlO3 substrates. The superconducting thin films were deposited by sequential electron beam evaporation of Cu, Y, and BaF2 with a post anneal. Patterning of the superconducting film was done using negative photolithography. A ring resonator was also fabricated from a thin gold film as a control. Both resonators had a gold ground plane on the backside of the substrate. The ring resonators' reflection coefficients were measured as a function of frequency from 33 to 37 GHz at temperatures ranging from 20 K to 68 K. The resonator exhibited two resonances which were at 34.5 and 35.7 GHz at 68 K. The resonant frequencies increased with decreasing temperature. The magnitude of the reflection coefficients was in the calculation of the unloaded Q-values. The performance of the evaporated and gold resonator are compared with the performance of a laser ablated YBa2Cu3O(7-x) resonator. The causes of the double resonance are discussed.

Rohrer, Norman J.↗
NASA NTRS1972

Hydrogen as an atomic beam standard

After a preliminary discussion of feasibility, new experimental work with a hydrogen beam is described. A space focused magnetic resonance technique with separated oscillatory fields is used with a monochromatic beam of cold hydrogen atoms which are selected from a higher temperature source. The first resonance curves and other experimental results are presented. These results are interpreted from the point of view of accuracy potential and frequency stability, and are compared with hydrogen maser and cesium beam capabilities.

Peters, H. E.↗
NASA NTRS1991

Paramagnetic resonance and susceptibility of ilmenite, FeTiO3 crystal

Large high-purity single crystals of FeTiO3 with ilmenite structure have been grown from a stoichiometric melt of Fe2O3 and TiO2 under an inert atmosphere using the modified Czochralski technique. Susceptibility and X-band paramagnetic resonance studies have been performed. Susceptibility measurements indicate a Neel temperature of about 59 K. The paramagnetic resonance spectrum for magnetic field perpendicular to the crystal c axis consists of a portion of a single, very intense approximately Lorentzian absorption line with its peak at about 600 G and half width at half maximum almost 1200 G. The absorption extends to zero magnetic field. For magnetic field approximately parallel to the c axis, the paramagnetic absorption is much smaller and may be considered a superposition of two approximately Lorentzian line shapes. The magnetic resonance measurements indicate a weak temperature dependence and large angular anisotropy.

Mcdonald, P. F.↗
DOE OSTI2020

Insights into Molecular Magnetism in Metal–Metal Bonded Systems as Revealed by a Spectroscopic and Computational Analysis of Diiron Complexes

A pair of bimetallic compounds featuring Fe–Fe bonds, [Fe( i PrNPPh 2 ) 3 FeR] (R = PMe 3 , ≡N t Bu), have been investigated using High-Frequency Electron Paramagnetic Resonance (HFEPR) as well as field- and temperature-dependent 57 Fe nuclear γ resonance (Mössbauer) spectroscopy. To gain insight into the local site electronic structure, we have concurrently studied a compound containing a single Fe(II) in a geometry analogous to that of one of the dimer sites. Our spectroscopic studies have allowed for the assessment of the electronic structure via the determination of the zero-field splitting and 57 Fe hyperfine parameters for the entire series. We also report on our efforts to correlate structure with physical properties in metal–metal bonded systems using ligand field theory guided by quantum chemical calculations. Through the insight gained in this study, we discuss strategies for the design of single-molecule magnets based on polymetallic compounds linked via direct metal–metal bonds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1972

Remote sensing of atmospheric and surface temperatures with microwaves.

Solids, liquids, and gases emit at microwave wavelengths measurable amounts of black-body thermal radiation. Receiver sensitivities readily approach 0.01 K, and permit accurate measurements of land, sea, and atmospheric temperatures. Sea and land temperature measurements must be corrected for the effects of surface emissivity, but these effects can often be measured or estimated. Observations near the 5 mm wavelength 02 resonances can yield atmospheric temperature profiles with an approximate accuracy of 2 K for altitudes 0-80 km. Such measurements from balloons and aircraft suggest that the planned earth-orbital satellite experiments will yield data valuable for numerical weather prediction. Ground-based radio telescopes and planetary-probes have yielded similar information about the surfaces and atmospheres of other planets.

Staelin, D. H.↗
NASA NTRS1992

Conductor-backed coplanar waveguide resonators of Y-Ba-Cu-O and Tl-Ba-Ca-Cu-O on LaAlO3

Conductor-backed coplanar waveguide (CBCPW) resonators operating at 10.8 GHz have been fabricated from Tl-Ba-Ca-O (TBCCO) and Y-Ba-Cu-O (YBCO) thin films on LaAlO3. The resonators consist of a coplanar waveguide (CPW) patterned on the superconducting film side of the LaAlO3 substrate with a gold ground plane coated on the opposite side. These resonators were tested in the temperature range from 14 to 106 K. At 77 K, the best of our TBCCO and YBCO resonators have an unloaded quality factor (Qo) 7 and 4 times, respectively, larger than that of a similar all-gold resonator. In this study, the Qo's of the TBCCO resonators were larger than those of their YBCO counterparts throughout the aforementioned temperature range.

Miranda, F. A.↗
DOE OSTI2022

High quality superconducting Nb co-planar resonators on sapphire substrate

We present measurements and simulations of superconducting Nb co-planar waveguide resonators on sapphire substrate down to millikelvin temperature range with different readout powers. In the high temperature regime, we demonstrate that the Nb film residual surface resistance is comparable to that observed in the ultra-high quality, bulk Nb 3D superconducting radio frequency cavities while the resonator quality is dominated by the BCS thermally excited quasiparticles. At low temperature both the resonator quality factor and frequency can be well explained using the two-level system models. Through the energy participation ratio simulations, we find that the two-level system loss tangent is $\sim 10^{-2}$, which agrees quite well with similar studies performed on the Nb 3D cavities.

Zhu, S.↗
DOE OSTI2023

Quasiparticle Generation-Recombination Noise in the Limit of Low Detector Volume

We have measured the quasiparticle generation-recombination (GR) noise in aluminium lumped element kinetic inductors with a wide range of detector volumes at various temperatures. The basic detector consists of meandering inductor and interdigitated capacitor fingers. The inductor volume is varied from 2 to 153 mu m(3) by changing the inductor width and length to maintain a constant inductance. We started with measuring the power spectrum density (PSD) of the detectors frequency noise which is a function of GR noise and we clearly observed the spectrum roll off at 10 kHz which corresponds to the quasiparticle lifetime. Using data from a temperature sweep of the resonator frequency we convert the frequency fluctuation to quasiparticle fluctuation and observe its strong dependence on detector volume: detectors with smaller volume display less quasiparticle noise amplitude. Meanwhile we observe a saturated quasiparticle density at low temperature from all detectors as the quasiparticle life time tqp approaches a constant value at low temperature.

Li, Juliang↗
DOE OSTI2026

Structural Propensities in Cs2MBiX6 (M=Na, Ag; X=Cl, Br) Bismuth Halide Double Perovskites

A previously unreported low-temperature phase transition in the bismuth halide double perovskite Cs2AgBiCl6 is reported, thereby establishing trends in the structural ground state across Cs2NaBiCl6, Cs2AgBiCl6, and Cs2AgBiBr6. Using the combined toolkit of variable-temperature synchrotron X-ray and neutron powder diffraction, Raman spectroscopy, and density-functional theory–based electronic structure modeling, we demonstrate a cubic Fm¯3m → tetragonal I4/m transition upon cooling with distinct onset temperatures. Neutron powder diffraction refinements permit the unambiguously assignment of the low-temperature phase of Cs2NaBiCl6 to I4/m, correcting prior reports of an I4/mmm ground state. Cs2AgBiCl6 is also found to transforms to a structure crystallizing in the I4/m space group at low temperatures. Temperaturedependent Raman data and density-functional theory-based modeling capture the softening and freezing of out-of-phase octahedral-tilt modes and quantify relative instabilities. Solid-state nuclear magnetic resonance spectroscopy at room temperature completes the characterization and helps underpin the subtle differences in covalency across the compounds. Trends in the phase transition temperature Ts and tilt magnitudes emerge from coupled effects of halide identity, M(I)–site bonding character, and a mismatch between interatomic distances. These results establish the structure– dynamics–bonding framework for tuning tilt-driven instabilities in halide double perovskites.

Tian, Haowen↗
NASA NTRS1980

Gigahertz analog modulation and differential delay of GaAlAs lasers - Temperature and current behavior

Gigahertz analog modulation characteristics of broad-area commercially available GaAlAs lasers have been investigated as a function of temperature and current in the vicinity of the upper frequency limit, where the resonance phenomena occur. The optimum temperature for small-signal amplitude modulation was found to be around -15 C for our particular broad-stripe geometry double-heterostructure laser. The Q was found to increase by a factor of 2 and the bandwidth by about 2%; the external quantum efficiency was maximized in this range. The optimum dc current bias was about 2% above the threshold current. Differential delays have also been measured down to a few picosecond accuracy by a unique phase-angle measurement method using a vector voltmeter. Some of the temperature effects observed may be related to mode changes and multimode and superradiance behavior.

Eng, S. T.↗
NASA NTRS1973

Electromagnetic instabilities in non-uniform anisotropic plasmas

The mechanisms of electromagnetic instabilities in nonuniform plasmas are analyzed, taking into account the anisotropy in temperature and temperature gradients. It is shown that resonance-type drift instabilities can be produced in nonuniform plasmas by resonant interactions between ions or electrons and plasma drift waves when the temperature anisotropy and temperature gradients vary widely. In contrast, production of off-resonance type instabilities is found to be possible only when the temperature gradients are much greater than the magnetic field gradients. It is pointed out that these findings are applicable to solar wind plasmas with hydromagnetic instabilities and shock transition regions. Attention is given to the occurrence of resonance ion instabilities and off-resonance drift cyclotron instabilities in the solar wind.

Buti, B.↗