Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “reaction wheels”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Development of a Two-Wheel Contingency Mode for the MAP Spacecraft

The Microwave Anisotropy Probe (MAP) is a follow-on mission to the Cosmic Background Explorer (COBE), and is currently collecting data from its orbit near the second Sun-Earth libration point. Due to limited mass, power, and financial resources, a traditional reliability concept including fully redundant components was not feasible for MAP. Instead, the MAP design employs selective hardware redundancy in tandem with contingency software modes and algorithms to improve the odds of mission success. One direction for such improvement has been the development of a two-wheel backup control strategy. This strategy would allow MAP to position itself for maneuvers and collect science data should one of its three reaction wheels fail. Along with operational considerations, the strategy includes three new control algorithms. These algorithms would use the remaining attitude control actuators-thrusters and two reaction wheels-in ways that achieve control goals while minimizing adverse impacts on the functionality of other subsystems and software.

Starin, Scott R.↗
NASA NTRS2013

Fault Protection Design and Testing for the Cassini Spacecraft in a "Mixed" Thruster Configuration

NASA's Cassini Spacecraft, launched on October 15th, 1997 and arrived at Saturn on June 30th, 2004, is the largest and most ambitious interplanetary spacecraft in history. In order to meet the challenging attitude control and navigation requirements of the orbit profile at Saturn, Cassini is equipped with a monopropellant thruster based Reaction Control System (RCS), a bipropellant Main Engine Assembly (MEA) and a Reaction Wheel Assembly (RWA). In 2008, after 11 years of reliable service, several RCS thrusters began to show signs of end of life degradation, which led the operations team to successfully perform the swap from the A-branch to the B-branch RCS system. If similar degradation begins to occur on any of the B-branch thrusters, Cassini might have to assume a "mixed" thruster configuration, where a subset of both A and B branch thrusters will be designated as prime. The Cassini Fault Protection FSW was recently updated to handle this scenario. The design, implementation, and testing of this update is described in this paper.

propellant↗
NASA NTRSDate not supplied

Reflectivity Control Device (RCD) Momentum Management for Solar Cruiser and Future Solar Sail Missions

Solar sails provide propulsion from solar photonic pressure without the need for propellant. This advantage can be reduced or eliminated if propellant is required for attitude control. The current state of the art for solar sail attitude control is that of the solar sail mission Near Earth Asteroid Scout, which employs an Adjustable Mass Translator for pitch and yaw momentum management of reaction wheels, but must use a cold gas Reaction Control System for roll axis momentum management. It is highly desirable for solar sails to use an attitude control system that does not include propellant, so here we present a novel method of managing momentum on the roll axis. For the upcoming Solar Cruiser solar sail mission, for roll axis momentum management we plan to use Reflectivity Control Devices (RCDs), thin-film Polyimide Liquid Crystal Devices that are capable of changing optical properties on command, thus affording the opportunity to provide “photonic only” control if placed appropriately on the surface of the sail. RCD design for roll momentum management is multifaceted, and must include performance (degree of change in optical properties), RCD array size, locations of clusters on the sail, orientation with respect to the sail plane, and orientation out of the sail plane. Here we provide an explanation of the basic technology, optimal orientation, sizing, and location of RCDs, results of trade studies for Solar Cruiser, lessons learned from Solar Cruiser, and scalability for future solar sail missions. RCDs will dramatically improve the performance of the Solar Cruiser Momentum Management System compared to that of NEA Scout and will continue to benefit other future solar sail missions.

Daniel Tyler↗
NASA NTRSDate not supplied

Reflectivity Control Device (RCD) Roll Momentum Management for Solar Cruiser and Future Solar Sail Missions

Solar sails provide propulsion from solar photonic pressure without the need for propellant. This advantage can be reduced or eliminated if propellant is required for attitude control. The current state of the art for solar sail attitude control is that of the solar sail mission Near Earth Asteroid Scout, which employs an Adjustable Mass Translator for pitch and yaw momentum management of reaction wheels, but must use a cold gas Reaction Control System for roll axis momentum management. It is highly desirable for solar sails to use an attitude control system that does not include propellant, so here we present a novel method of managing momentum on the roll axis. For the upcoming Solar Cruiser solar sail mission, for roll axis momentum management we plan to use Reflectivity Control Devices (RCDs), thin-film Polyimide Liquid Crystal Devices that are capable of changing optical properties on command, thus affording the opportunity to provide “photonic only” control if placed appropriately on the surface of the sail. RCD design for roll momentum management is multifaceted, and must include performance (degree of change in optical properties), RCD array size, locations of clusters on the sail, orientation with respect to the sail plane, and orientation out of the sail plane. Here we provide an explanation of the basic technology, optimal orientation, sizing, and location of RCDs, results of trade studies for Solar Cruiser, lessons learned from Solar Cruiser, and scalability for future solar sail missions. RCDs will dramatically improve the performance of the Solar Cruiser Momentum Management System compared to that of NEA Scout and will continue to benefit other future solar sail missions.

Daniel Tyler↗
NASA NTRS2013

DAWN'S Operations in Cruise from Vesta to Ceres

On 5 September 2012, Dawn concluded its successful exploration of Vesta, the second most massive object in the main asteroid belt. The spacecraft departed after 14 months in orbit and is now using its ion propulsion system to travel to dwarf planet Ceres, the most massive main-belt asteroid. The principal activity now is thrusting with the ion propulsion system to provide the 3.4 km/s required to rendezvous with Ceres early in 2015. Because two of the four reaction wheels have experienced faults and are likely unrecoverable, a substantial effort has been invested in preparing for Ceres operations with alternate attitude control methods. The project has engaged in an intensive campaign to reduce hydrazine expenditures, which has resulted in a significant increase in the hydrazine expected to be available for Ceres. Based on this work, studies provide good confidence that the required activities at Ceres can be completed. This paper describes post-Vesta operations, including measures taken to conserve hydrazine as well as other preparations for Ceres.

Dawn↗
NASA NTRS1987

The dynamics and control of the Space Station polar platform

The Space Station polar platform will carry a variety of earth observation instruments for NASA and the National Oceanic and Atmospheric Administration. In this paper, the asymmetrical platform is modeled as three connected rigid bodies. A generalized angular momentum equation is employed to derive the rotational equations of motion. These equations are linearized and used for preliminary sizing of control devices using a classical control approach. Two control systems are considered to stabilize the platform and satisfy the pointing requirements. The first system is composed of a single variable-speed, double-gimbaled momentum wheel and the second consists of three-reaction wheels. The performance of each system is assessed using a linear optimal control approach.

Wahbah, M. M.↗
NASA NTRS1990

Inertia-Wheel Vibration-Damping System

Proposed electromechanical system would damp vibrations in large, flexible structure. In active vibration-damping system motors and reaction wheels at tips of appendages apply reaction torques in response to signals from accelerometers. Velocity signal for vibrations about one axis processes into control signal to oppose each of n vibrational modes. Various modes suppressed one at a time. Intended primarily for use in spacecraft that has large, flexible solar panels and science-instrument truss assembly, embodies principle of control interesting in its own right and adaptable to terrestrial structures, vehicles, and instrument platforms.

Fedor, Joseph V.↗
NASA NTRS1992

Spacecraft stability and control

The Earth's first artificial satellite, Sputnik 1, slowly tumbled in orbit. The first U.S. satellite, Explorer 1, also tumbled out of control. Today, satellite stability and control has become a higher priority. For a satellite design that is to have a life expectancy of 14 years, appropriate spacecraft flight control systems will be reviewed, stability requirements investigated, and an appropriate flight control system recommended in order to see the design process. Disturbance torques, including aerodynamic, magnetic, gravity gradient, solar, micrometeorite, debris, collision, and internal torques, will be assessed to quantify the disturbance environment so that the required compensating torques can be determined. The control torques, including passive versus active, momentum control, bias momentum, spin stabilization, dual spin, gravity gradient, magnetic, reaction wheels, control moment gyros, inertia augmentation techniques, three-axis control, and reaction control systems (RCSs), will be considered. Conditions for stability will also be considered.

Barret, Chris↗
NASA NTRS2016

Dawn's Mission at Ceres

Dawn is NASA's ninth Discovery class mission. The Dawn spacecraft was designed to orbit both the giant asteroid Vesta and the dwarf planet Ceres in succession, a mission only made possible by the high efficiency of ion propulsion. While the same spacecraft visited both bodies, the mission planning and maneuver execution at the two bodies were necessarily very different. The mission at Vesta benefited from at least three functioningreaction control wheels. At Ceres, all maneuvering and coasting during transfers was done without reaction wheel control due to the loss of the second of four wheels while departing Vesta. Loss of the second wheel made conserving attitude control propellant (hydrazine) critical to achieving mission success at Ceres. To save hydrazine, avoiding unnecessary coasting and attitude turns became essential during the interplanetary cruise to Ceres and for all transfers once at Ceres. In contrast, operations at Vesta did not need to avoid coasting. Operating at Ceres requires being farther from the Sun. Greaterheliocentric distances (approaching 3 AU (Astronomical Units) make Dawn's attitude control constraints while maneuvering more restrictive as a result of reduced control authority.

Whiffen, Gregory J.↗
NASA NTRS1992

Spacecraft flight control system design selection process for a geostationary communication satellite

The Earth's first artificial satellite, Sputnik 1, slowly tumbled in orbit. The first U.S. satellite, Explorer 1, also tumbled out of control. Now, as we launch the Mars observer and the Cassini spacecraft, stability and control have become higher priorities. The flight control system design selection process is reviewed using as an example a geostationary communication satellite which is to have a life expectancy of 10 to 14 years. Disturbance torques including aerodynamic, magnetic, gravity gradient, solar, micrometeorite, debris, collision, and internal torques are assessed to quantify the disturbance environment so that the required compensating torque can be determined. Then control torque options, including passive versus active, momentum control, bias momentum, spin stabilization, dual spin, gravity gradient, magnetic, reaction wheels, control moment gyros, nutation dampers, inertia augmentation techniques, three-axis control, reactions control system (RCS), and RCS sizing, are considered. A flight control system design is then selected and preliminary stability criteria are met by the control gains selection.

Barret, C.↗
NASA NTRS2002

Development of a Two-Wheel Contingency Mode for the MAP Spacecraft

In the event of a failure of one of MAP's three reaction wheel assemblies (RWAs), it is not possible to achieve three-axis, full-state attitude control using the remaining two wheels. Hence, two of the attitude control algorithms implemented on the MAP spacecraft will no longer be usable in their current forms: Inertial Mode, used for slewing to and holding inertial attitudes, and Observing Mode, which implements the nominal dual-spin science mode. This paper describes the effort to create a complete strategy for using software algorithms to cope with a RWA failure. The discussion of the design process will be divided into three main subtopics: performing orbit maneuvers to reach and maintain an orbit about the second Earth-Sun libration point in the event of a RWA failure, completing the mission using a momentum-bias two-wheel science mode, and developing a new thruster-based mode for adjusting the inertially fixed momentum bias. In this summary, the philosophies used in designing these changes is shown; the full paper will supplement these with algorithm descriptions and testing results.

Starin, Scott R.↗
NASA NTRS1988

Angular-Momentum-Compensating Servomechanism

Servomechanism for rotating an instrumentation platform isolates supporting vehicle or stationary platform from reaction torques producedby rotations. Prevents aiming of instrument from disturbing vehicle or other instrument platforms. Rotating oppositely to instrument platform, reaction wheel, motor, and gear 1 have angular momentum equal and opposite to gear 2, output shaft, and platform. External torque reaction to rotation of platform canceled. Although spur gears appear in schematic diagram, gear train made of spline gears.

Marchetto, Carl A.↗
NASA NTRS2005

The Use of a Gyroless Wheel-Tach Controller in SDO Safehold Mode

This paper describes the progression of the Safehold mode design on the Solar Dynamics Observatory satellite. Safehold uses coarse Sun sensors and reaction wheel tachometers to keep the spacecraft in a thermally safe and power-positive attitude. The control algorithm is described, and simulation results shown. Specific control issues arose when the spacecraft entered eclipse, and a description of the trade study which added gyroscopes to the mode is included. The paper concludes with the results from the linear and nonlinear stability analysis.

Bourkland, Kristin L.↗
NASA NTRSDate not supplied

Correlated Electromagnetic Levitation Actuator: A Reaction Sphere Based Attitude Control System

To address problems experienced by current reaction wheels and control moment gyroscopebased attitude control systems (ACS), researchers at NASA’s Marshall Space Flight Center have begun developing a reaction sphere actuator based on correlated electromagnetic levitation that will be immune to destructive bearing friction, momentum saturation, and gimbal lock. The Correlated Electromagnetic Levitation Actuator (CELA) advances the state of the art of reaction sphere ACSs by employing the concept of correlated magnetics. It is a frictionless, direct-drive reaction sphere that harnesses a unique technology with an array of applications across multiple disciplines. Correlated electromagnets function in a manner that is analogous to a matched filter; the convolution of two signals is peaked at the index representing the greatest match. For CELA, the signals are the patterns of magnetic flux density as a function of position. The magnitude of the convolution equates to an attractive or repulsive force, and these forces can be azimuthal or radial. The development of CELA is based in four distinct disciplines: Advanced Manufacturing, Prototype Development, Electromagnetic Modeling, and Controls. We are developing novel manufacturing techniques required to build arrays of permanent and electromagnet dipoles on curved surfaces. To print the permanent magnetic array, we have developed a probe with pyramidal magnets that will reside on a robotic arm to induce localized magnetic fields on a surface. The probe also includes the ability to erase dipole patterns from a permanent magnet by heating the surface to its Curie temperature. A number of test articles and prototypes have been developed using additive manufacturing methods. These prototypes have included hemispherical motors to test the drive algorithm, and a levitation test bed that demonstrates a magnetic bearing method based on attractive magnetic forces and ratiometric Hall effect sensors. We developed an array of electromagnetic dipoles on a printed circuit board (PCB) with individual H-bridges controlling each coil. This device created various flux density patterns and we measured their magnetic fields using a custom Hall effect 3-D probe and a LabVIEW virtual instrument. These data will serve as a benchmark for characterizing the accuracy of future models. Current work is focused on modeling the magnetic fields of our prototype arrays using COMSOL Finite Element Analysis and verifying the model against our test data. Accurate modeling will allow us to quickly test new patterns of electromagnets and their macro behavior. Eventually, the magnetic field models will be implemented in our controls simulations to facilitate precise control of the reaction sphere. Initial model results agree with field measurements to within 1 G (5% of measured flux density). Currently, we are testing different material properties of the electromagnets and their magnetic fields and thermal effects. These results will be used to refine the design of the electromagnetic dipoles. Our control efforts have centered on developing commutation, levitation, and field pattern shaping hardware in the form of breadboards and PCBs with software running on a local microcontroller. In addition, our partners developed MATLAB Simulink models to demonstrate a PID controller thatmitigates disturbance forces resulting from the interaction of drive and levitation magnetics. Finally, we have designed a three-axis test stand that will be used in future work to demonstrate CELA’s orientation control capability.

controls↗
NASA NTRS2002

Energy Storage Flywheels on Spacecraft

With advances in carbon composite material, magnetic bearings, microprocessors, and high-speed power switching devices, work has begun on a space qualifiable Energy Momentum Wheel (EMW). An EMW is a device that can be used on a satellite to store energy, like a chemical battery, and manage angular momentum, like a reaction wheel. These combined functions are achieved by the simultaneous and balanced operation of two or more energy storage flywheels. An energy storage flywheel typically consists of a carbon composite rotor driven by a brushless DC motor/generator. Each rotor has a relatively large angular moment of inertia and is suspended on magnetic bearings to minimize energy loss. The use of flywheel batteries on spacecraft will increase system efficiencies (mass and power), while reducing design-production time and life-cycle cost. This paper will present a discussion of flywheel battery design considerations and a simulation of spacecraft system performance utilizing four flywheel batteries to combine energy storage and momentum management for a typical LEO satellite. A proposed set of control laws and an engineering animation will also be presented. Once flight qualified and demonstrated, space flywheel batteries may alter the architecture of most medium and high-powered spacecraft.

Bartlett, Robert O.↗
NASA NTRSDate not supplied

Correlated Electromagnetic Levitation Actuator: A Reaction Sphere-Based Attitude Control System

To address problems experienced by current reaction wheels and control moment gyroscopebased attitude control systems (ACS), researchers at National Aeronautics and Space Administration’s (NASA’s) Marshall Space Flight Center (MSFC) have begun developing a reaction sphere actuator based on correlated electromagnetic levitation that will be immune to destructive bearing friction, momentum saturation, and gimbal lock. The Correlated Electromagnetic Levitation Actuator (CELA) advances the state of the art of reaction sphere ACSs by employing the concept of correlated magnetics. It is a frictionless, direct-drive reaction sphere that harnesses a unique technology with an array of applications across multiple disciplines. Correlated electromagnets function in a manner that is analogous to a matched filter; the convolution of two signals is peaked at the index representing the greatest match. For CELA, the signals are the patterns of magnetic flux density as a function of position. The magnitude of the convolution equates to an attractive or repulsive force, and these forces can be azimuthal or radial. The development of CELA is based in four distinct disciplines: Advanced Manufacturing, Prototype Development, Electromagnetic Modeling, and Controls. We are developing novel manufacturing techniques required to build arrays of permanent and electromagnet dipoles on curved surfaces. To print the permanent magnetic array, we have developed a probe with pyramidal magnets that will reside on a robotic arm to induce localized magnetic fields on a surface. We have also used high temperature ovens to erase dipole patterns from a permanent magnet by heating the surface to its Curie temperature. A number of test articles and prototypes have been developed using additive manufacturing methods. These prototypes have included hemispherical motors to test the drive algorithm, and a levitation test bed that demonstrates a magnetic bearing method based on attractive magnetic forces and ratiometric Hall effect sensors. We developed an array of electromagnetic dipoles on a printed circuit board (PCB) with individual H-bridges controlling each coil. This device created various flux density patterns and we measured their magnetic fields using a custom Hall effect 3-D probe and a LabVIEW virtual instrument. These data will serve as a benchmark for characterizing the accuracy of future models. Current work is focused on modeling the magnetic fields of our prototype arrays using COMSOL finite element analysis (FEA) and verifying the model against our test data. Accurate modeling will allow us to quickly test new patterns of electromagnets and their macro behavior. Eventually, the magnetic field models will be implemented in our controls simulations to facilitate precise control of the reaction sphere. Initial model results agree with field measurements to within 1 G (5% of measured flux density). Currently, we are testing different material properties of the electromagnets and their magnetic fields and thermal effects. These results will be used to refine the design of the electromagnetic dipoles. Our control efforts have centered on developing commutation, levitation, and field pattern shaping hardware in the form of breadboards and PCBs with software running on a local microcontroller. In addition, our partners developed MATLAB Simulink models to demonstrate a PID controller that mitigates disturbance forces resulting from the interaction of drive and levitation magnetics. Finally, we have designed a three-axis test stand that will be used in future work to demonstrate CELA’s orientation control capability.

reaction sphere↗
NASA NTRS1995

Two-micron Laser Atmospheric Wind Sounder (LAWS) pointing/tracking study

The objective of the study was to identify and model major sources of short-term pointing jitter for a free-flying, full performance 2 micron LAWS system and evaluate the impact of the short-term jitter on wind-measurement performance. A fast steering mirror controls system was designed for the short-term jitter compensation. The performance analysis showed that the short-term jitter performance of the controls system over the 5.2 msec round-trip time for a realistic spacecraft environment was = 0.3 micro rad, rms, within the specified value of less than 0.5 micro rad, rms, derived in a 2 micron LAWS System Study. Disturbance modes were defined for: (1) the Bearing and Power Transfer Assembly (BAPTA) scan bearing, (2) the spacecraft reaction wheel torques, and (3) the solar array drive torques. The scan bearing disturbance was found to be the greatest contributing noise source to the jitter performance. Disturbances from the fast steering mirror reaction torques and a boom-mounted cross-link antenna clocking were also considered but were judged to be small compared to the three principal disturbance sources above and were not included in the final controls analysis.

Manlief, Scott↗