Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “pattern transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Assessment of a 3-D boundary layer analysis to predict heat transfer and flow field in a turbine passage

An assessment was made of the applicability of a three dimensional boundary layer analysis of heat transfer, total pressure losses, and streamline flow patterns on the surfaces of both stationary and rotating turbine passages. In support of this effort, an analysis was developed to calculate a general nonorthogonal surface coordinate system for arbitrary three dimensional surfaces and also to calculate the boundary layer edge conditions for compressible flow using the surface Euler equations and experimental pressure distributions. Calculations are presented for the pressure, endwall, and suction surfaces of a stationary cascade and for the pressure surface of a rotating turbine blade. The results strongly indicate that the three dimensional boundary layer analysis can give good predictions of the flow field, loss, and heat transfer on the pressure, suction, and endwall surface of a gas turbine passage.

Anderson, O. L.↗
NASA NTRS1985

User's manual for three dimensional boundary layer (BL3-D) code

An assessment has been made of the applicability of a 3-D boundary layer analysis to the calculation of heat transfer, total pressure losses, and streamline flow patterns on the surface of both stationary and rotating turbine passages. In support of this effort, an analysis has been developed to calculate a general nonorthogonal surface coordinate system for arbitrary 3-D surfaces and also to calculate the boundary layer edge conditions for compressible flow using the surface Euler equations and experimental data to calibrate the method, calculations are presented for the pressure endwall, and suction surfaces of a stationary cascade and for the pressure surface of a rotating turbine blade. The results strongly indicate that the 3-D boundary layer analysis can give good predictions of the flow field, loss, and heat transfer on the pressure, suction, and endwall surface of a gas turbine passage.

Anderson, O. L.↗
NASA NTRS1984

Heat transfer and oil flow studies on a single-stage-to-orbit control-configured winged entry vehicle

Results are presented for oil flow and phase change paint heat transfer tests conducted on a 0.006 scale model of a proposed single stage to orbit control configured vehicle. The data were taken at angles of attack up to 40 deg at a free stream Mach number of 10 for Reynolds numbers based on model length of 0.5 x 10 to the 6th power, 1.0 x 10 to the 6th power and 2.0 x 10 to the 6th power. The magnitude and distribution of heating are characterized in terms of angle of attack and Reynolds number aided by an analysis of the flow data which are used to suggest the presence of various three dimensional flow structures that produce the observed heating patterns. Of particular interest are streak heating patterns that result in high localized heat transfer rates on the wing windward surface at low to moderate angles of attack. These streaks are caused by the bow-shock/wing-shock interaction and formation of the wing-shock. Embedded vorticity was found to be associated with these interactions.

Helms, V. T., III↗
NASA NTRS1991

New applications of liquid-crystal thermography in rotating turbomachinery heat transfer research

Two new liquid-crystal thermography techniques developed for use in rotating heat transfer experiments are described. In one experiment steady-state heat transfer data were obtained on the exterior surface of rotating turbine airfoil models. In the second study a transient technique was employed to obtain interior-surface heat transfer data in a rotating turbine blade coolant passage model. Sample data are presented in the form of photographs of the liquid-crystal temperature patterns and as contour maps and distributions of heat transfer on the rotor and coolant passage surfaces.

Blair, M. F.↗
DOE OSTI2021

The stability of Cl-, Br-, and I-passivated Si(100)-(2 × 1) in ambient environments for atomically-precise pattern preservation

Abstract Atomic precision advanced manufacturing (APAM) leverages the highly reactive nature of Si dangling bonds relative to H- or Cl-passivated Si to selectively adsorb precursor molecules into lithographically defined areas with sub-nanometer resolution. Due to the high reactivity of dangling bonds, this process is confined to ultra-high vacuum (UHV) environments, which currently limits its commercialization and broad-based appeal. In this work, we explore the use of halogen adatoms to preserve APAM-derived lithographic patterns outside of UHV to enable facile transfer into real-world commercial processes. Specifically, we examine the stability of H-, Cl-, Br-, and I-passivated Si(100) in inert N 2 and ambient environments. Characterization with scanning tunneling microscopy and x-ray photoelectron spectroscopy (XPS) confirmed that each of the fully passivated surfaces were resistant to oxidation in 1 atm of N 2 for up to 44 h. Varying levels of surface degradation and contamination were observed upon exposure to the laboratory ambient environment. Characterization by ex situ XPS after ambient exposures ranging from 15 min to 8 h indicated the Br– and I–passivated Si surfaces were highly resistant to degradation, while Cl–passivated Si showed signs of oxidation within minutes of ambient exposure. As a proof-of-principle demonstration of pattern preservation, a H–passivated Si sample patterned and passivated with independent Cl, Br, I, and bare Si regions was shown to maintain its integrity in all but the bare Si region post-exposure to an N 2 environment. The successful demonstration of the preservation of APAM patterns outside of UHV environments opens new possibilities for transporting atomically-precise devices outside of UHV for integrating with non-UHV processes, such as other chemistries and commercial semiconductor device processes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1999

Experimental Investigation of Pool Boiling Heat Transfer Enhancement in Microgravity in the Presence of Electric Fields

In boiling high heat fluxes are possible driven by relatively small temperature differences, which make its use increasingly attractive in aerospace applications. The objective of the research is to develop ways to overcome specific problems associated with boiling in the low gravity environment by substituting the buoyancy force with the electric force to enhance bubble removal from the heated surface. Previous studies indicate that in terrestrial applications nucleate boiling heat transfer can be increased by a factor of 50, as compared to values obtained for the same system without electric fields. The goal of our research is to experimentally explore the mechanisms responsible for EHD heat transfer enhancement in boiling in low gravity conditions, by visualizing the temperature distributions in the vicinity of the heated surface and around the bubble during boiling using real-time holographic interferometry (HI) combined with high-speed cinematography. In the first phase of the project the influence of the electric field on a single bubble is investigated. Pool boiling is simulated by injecting a single bubble through a nozzle into the subcooled liquid or into the thermal boundary layer developed along the flat heater surface. Since the exact location of bubble formation is known, the optical equipment can be aligned and focused accurately, which is an essential requirement for precision measurements of bubble shape, size and deformation, as well as the visualization of temperature fields by HI. The size of the bubble and the frequency of bubble departure can be controlled by suitable selection of nozzle diameter and mass flow rate of vapor. In this approach effects due to the presence of the electric field can be separated from effects caused by the temperature gradients in the thermal boundary layer. The influence of the thermal boundary layer can be investigated after activating the heater at a later stage of the research. For the visualization experiments a test cell was developed. All four vertical walls of the test cell are transparent, and they allow transillumination with laser light for visualization experiments by HI. The bottom electrode is a copper cylinder, which is electrically grounded. The copper block is heated with a resistive heater and it is equipped with 6 thermocouples that provide reference temperatures for the measurements with HI. The top electrode is a mesh electrode. Bubbles are injected with a syringe into the test cell through the bottom electrode. The working fluids presently used in the interferometric visualization experiments, water and PF 5052, satisfy requirements regarding thermophysical, optical and electrical properties. A 30kV power supply equipped with a voltmeter allows to apply the electric field to the electrodes during the experiments. The magnitude of the applied voltage can be adjusted either manually or through the LabVIEW data acquisition and control system connected to a PC. Temperatures of the heated block are recorded using type-T thermocouples, whose output is read by a data acquisition system. Images of the bubbles are recorded with 35mm photographic and 16mm high-speed cameras, scanned and analyzed using various software packages. Visualized temperature fields HI allows the visualization of temperature fields in the vicinity of bubbles during boiling in the form of fringes. Typical visualized temperature distributions around the air bubbles injected into the thermal boundary layer in PF5052 are shown. The temperature of the heated surface is 35 C. The temperature difference for a pair of fringes is approximately 0.05 C. The heat flux applied to the bottom surface is moderate, and the fringe patterns are regular. In the image a bubble penetrating the thermal boundary layer is visible. Because of the axial symmetry of the problem, simplified reconstruction techniques can be applied to recover the temperature field. The thermal plume developing above the heated surface for more intensive heating is shown. The temperature distribution in the liquid is clearly 3D, and tomographic techniques have to be applied to recover the temperature distribution in such a physical situation. A sequence of interferometric images showing the temperature distribution around the rising bubble, recorded with a high-speed camera is shown. Again, the temperature distribution is 3D, and a more complex approach to the evaluation, the tomographic reconstruction has to be taken. Measurement of the temperature distribution from the fringe pattern temperature distributions that yield important information regarding heat transfer are determined. Two algorithms that allow the quantitative evaluation of interferometric fringe patterns and the reconstruction of temperature fields during boiling have been developed at the Heat Transfer Laboratory of the Johns Hopkins University. In the first algorithm the bubble is assumed to be axially symmetrical, which significantly reduces the computational effort for quantifying the temperature distribution around the bubble. For this purpose the thermal boundary layer around the bubble is divided into equidistant concentric shells, and the refractive index is assumed to be constant in each of the shells. Since large temperature gradients are expected in the vicinity of the bubble during boiling, the deflection of the light beam cannot be neglected in boiling experiments. Since the exit angle of the light beam is known, this allows to account for the deflections and phase shifts outside the boundary layer (in the bulk fluid and in the windows of the test cell). Three dimensional temperature distributions in the vicinity of the bubble are reconstructed using tomographic techniques. In tomography, the measurement volume is sliced into 2D planes. In the present study these planes are parallel to the heated surface. The objective is to determine the values of the field parameter of interest in form of the field function in these 2D planes. The field parameter is the change of the refractive index of the liquid in the measurement volume caused by temperature changes. By superimposing data for many 2D planes recorded at the same time instant, the 3D temperature distribution in the measurement volume is recovered.

Herman, Cila↗
NASA NTRS2023

Identifying and Documenting Expert Knowledge, A Practical Study of Design Patterns

Globalization, powered by digitization, is increasing technology growth and knowledge transfer rates to levels not seen in the previous 3500 years, obscuring absolute truth and accelerating rates of innovation and production. Competing,or remaining competitive, in this global marketplace requires a learning organization adopt a method of capture, retention, and reuse for demonstrated tacit knowledge to accelerate the development of increasingly complex systems of high quality at a reasonable cost. The architectural theory of Patterns and Pattern Language is a validated methodology for mining tacit domain knowledge from a proven system. This work applies architectural theory to a multi-year development experiment and captures exposed knowledgeas a design patternin a model based systems engineering tool, demonstrating applicability ofdigital engineering initiativesin thedescription and reuse of expert design knowledge.By creating and archiving model based expressions of expert knowledge,a learning organization canimprovepractical decision making and avoid uninformed concept phase decision making

systems engineering↗
NASA NTRS1979

Improving NASA's technology transfer process through increased screening and evaluation in the information dissemination program

The current status of NASA's technology transfer system can be improved if the technology transfer process is better understood. This understanding will only be gained if a detailed knowledge about factors generally influencing technology transfer is developed, and particularly those factors affecting technology transfer from government R and D agencies to industry. Secondary utilization of aerospace technology is made more difficult because it depends on a transfer process which crosses established organizational lines of authority and which is outside well understood patterns of technical applications. In the absence of a sound theory about technology transfer and because of the limited capability of government agencies to explore industry's needs, a team approach to screening and evaluation of NASA generated technologies is proposed which calls for NASA, and other organizations of the private and public sectors which influence the transfer of NASA generated technology, to participate in a screening and evaluation process to determine the commercial feasibility of a wide range of technical applications.

Laepple, H.↗
DOE OSTI2024

Liquid Piston with Spray Cooling Near-Isothermal Compressor

The goal of this project was to prototype and characterize the performance of a liquid-piston spray-cooled gas compressor. The working principle of the compressor enables optimized high-efficiency operation over a very wide range of operating conditions, unlike conventional compressors that are optimized for a narrow range of operating conditions. The compressor technology is suitable for many applications, such as gas pipeline transport, gas storage, and commercial and residential heat pumps. Both physical testing and computational fluid dynamics (CFD) modeling of the processes using the Oak Ridge National Laboratory high-performance computing center were completed. The experimental and CFD studies focused on a near-isothermal liquid-piston compressor (LPC) that uses propylene glycol to compress CO 2 . The first prototype demonstrated isothermal operation during several sequentially executed cycles of CO 2 compression and raised the temperature of the compressed CO 2 by only 2 K, compared with approximately 6 K when the gas was compressed non-isothermally. Isothermal operation was demonstrated at CO 2 flow rates of up to 2 L/min. The second prototype was designed with two compression chambers to allow continuous flow of high-pressure CO 2 . However, the design of the valve train to direct flow between the compression chambers was not sufficient to allow demonstration of CO 2 compression. Numerical simulations of the LPC in which the compression chamber was filled with propylene glycol injected from the bottom inlet were performed using large eddy simulation (LES) with the wall-adapting local eddy-viscosity subgrid-scale model coupled with the multiphase volume of fluid (VOF) model to simulate the transient interface between gas and liquid and to capture the heat and mass transfers within the compression chamber. In this effort, the effects of boundary conditions applied to the LES-VOF calculations (i.e., no wall, an adiabatic wall, and a wall with a heat flux subscribed) on the overall pressure and temperature of the CO 2 gas as well as the transient evolution of flow and heat transfer within the compression chamber were investigated and are discussed in this report. The LES calculation with no wall showed no dynamical flow patterns, and the volume-averaged temperature of CO 2 increased from 305 to 392.7 K, whereas LES calculations with a constant wall temperature or a wall heat flux had similar increases of CO 2 temperatures. The results of the LES simulation using a wall heat flux showed different stages in the compression process and revealed dynamical formation and interaction of CO 2 gas layers and circulation flow patterns within the chamber that contributed to the overall heat transfer between the solid wall, gas, and liquid surface in the compressor. Though an industrial partnership for commercializing the compressor was not secured, the technology was attractive for an industrial partner to use in two research proposals in response to US Department of Energy funding opportunity announcements.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Side Chain Dynamics of Poly(norbornene)- g -Poly(propylene oxide) Bottlebrush Polymers

The segmental dynamics of the side chains of poly(norbornene)- g -poly(propylene oxide) (PNB- g -PPO) bottlebrush polymer in comparison to PPO is studied by quasi-elastic neutron scattering. Having experimental time and length scale information simultaneously allows to extract spatial information in addition to relaxation time. Tethering one end of the PPO side chain onto a stiff PNB backbone slows down the segmental relaxation, over the length and time scales investigated. The power law dependence of the relaxation time on the momentum transfer, Q , indicates a more heterogeneous relaxation pattern for the bottlebrush polymer, whereas the linear PPO has less deviations from a homogenous relaxation. Similar conclusions can be drawn from the time dependent mean square displacement, $\langle$ r 2 ( t )$\rangle$, and the non-Gaussian parameter, α 2 ( t ). Herein, the bottlebrush polymer shows a more restricted dynamics, whereas the linear PPO reaches $\langle$ r 2 ( t )$\rangle$∝ t 0.5 at the highest temperature. The deviations from Gaussian behavior are evident at the α 2 ( t ). Both samples show a decaying α 2 ( t ). Finally, the non-Gaussian parameter supports the results from the power law dependence of the relaxation times, with lower α 2 ( t ) values for PPO compared to those for PNB-g-PPO, pointing to less deviations from Gaussian behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A Unified Interpretation of Variability in Precipitation Isotope Ratios

Abstract Several mechanisms have been proposed to explain why the isotope ratios of precipitation vary in space and time and why they correlate with other climate variables like temperature and precipitation. Here, we argue that this behavior is best understood through the lens of radiative transfer, which treats the depletion of atmospheric vapor transport by precipitation as analogous to the attenuation of light by absorption or scattering. Building on earlier work by Siler et al., we introduce a simple model that uses the equations of radiative transfer to approximate the two-dimensional pattern of the oxygen isotope composition of precipitation ( δ p ) from monthly mean hydrologic variables. The model accurately simulates the spatial and seasonal variability in δ p within a state-of-the-art climate model and permits a simple decomposition of δ p variability into contributions from gradients in evaporation and the length scale of vapor transport. Outside the tropics, δ p is mostly controlled by gradients in evaporation, whose dependence on temperature explains the positive correlation between δ p and temperature (i.e., the temperature effect). At low latitudes, δ p is mostly controlled by gradients in the transport length scale, whose inverse relationship with precipitation explains the negative correlation between δ p and precipitation (i.e., the amount effect). This suggests that the temperature and amount effects are both mostly explained by the variability in upstream rainout, but they reflect distinct mechanisms governing rainout at different latitudes. Significance Statement The isotopic composition of precipitation has long been used to make inferences about past climates based on its observed relationship with precipitation in the tropics and with temperature at higher latitudes. These relationships—known as the “amount effect” and “temperature effect,” respectively—have been attributed to many different mechanisms, most of which are thought to operate at either high or low latitudes but not both. Here, we present a unified framework for interpreting the isotope variability that can explain the latitude dependence of the temperature and amount effects despite making no distinction between high and low latitudes. Although our results are generally consistent with certain interpretations of the amount effect, they suggest that the temperature effect is widely misunderstood.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1985

Elastic scattering of alpha particles and the phase of the nucleon-nucleon scattering amplitude

Glauber theory can describe elastic scattering of alpha particles by He-4, He-3, H-2, and H-1 at 7 GeV/c if the phase of the nucleon-nucleon elastic-scattering amplitude varies with momentum transfer. The phase variation leads to diffraction patterns differing markedly from those typical of constant-phase calculations and greatly affects the magnitudes of the intensities. These changes are mainly due to changes in the interference between amplitudes for different orders of multiple scattering and to a decrease in their moduli.

Franco, V.↗
NASA NTRS1988

Magnetic fine structure of solar coronal loops

A numerical simulation of the effect of a random photospheric flow on the magnetic structure of a coronal loop is presented. An initially uniform field embedded in a perfectly conducting plasma is assumed, extending between two flat parallel plates representing the solar photosphere at both ends of the loop. The field is perturbed by a sequence of randomly phased, sinusoidal flow patterns applied at one of the boundary plates, and the corresponding sequence of force-free fields is determined. It is found that the electric currents generated by these flows develop a fine structure on a scale significantly smaller than the wavelength of the velocity patterns. This suggests that magnetic energy is transferred to smaller scale via a cascade process.

Van Ballegooijen, A. A.↗
NASA NTRS1990

Heat and moisture flux modeling of the FIFE grassland canopy aided by satellite derived canopy variables

Satellite data corresponding to radiance variables are used to derive three canopy properties which describe slowly modulating boundary conditions of the interface between the biosphere and the atmosphere. The canopy properties are key factors in the regulation of heat and moisture transfer and are found to be radiance patterns within a homogeneous ecosystem. The physical modeling technique is enhanced by the satellite data, and the surface fluxes are represented more accurately in the resulting biosphere-interface model.

Smith, Eric A.↗
NASA NTRS1998

Incorporating Endmember Variability into Spectral Mixture Analysis Through Endmember Bundles

Variation in canopy structure and biochemistry induces a concomitant variation in the top-of-canopy spectral reflectance of a vegetation type. Hence, the use of a single endmember spectrum to track the fractional abundance of a given vegetation cover in a hyperspectral image may result in fractions with considerable error. One solution to the problem of endmember variability is to increase the number of endmembers used in a spectral mixture analysis of the image. For example, there could be several tree endmembers in the analysis because of differences in leaf area index (LAI) and multiple scatterings between leaves and stems. However, it is often difficult in terms of computer or human interaction time to select more than six or seven endmembers and any non-removable noise, as well as the number of uncorrelated bands in the image, limits the number of endmembers that can be discriminated. Moreover, as endmembers proliferate, their interpretation becomes increasingly difficult and often applications simply need the aerial fractions of a few land cover components which comprise most of the scene. In order to incorporate endmember variability into spectral mixture analysis, we propose representing a landscape component type not with one endmember spectrum but with a set or bundle of spectra, each of which is feasible as the spectrum of an instance of the component (e.g., in the case of a tree component, each spectrum could reasonably be the spectral reflectance of a tree canopy). These endmember bundles can be used with nonlinear optimization algorithms to find upper and lower bounds on endmember fractions. This approach to endmember variability naturally evolved from previous work in deriving endmembers from the data itself by fitting a triangle, tetrahedron or, more generally, a simplex to the data cloud reduced in dimension by a principal component analysis. Conceptually, endmember variability could make it difficult to find a simplex that both surrounds the data cloud and has vertices that are realistic endmember spectra with reflectances between 0 and 1. In this paper, we create endmember bundles and bounding fraction images for an AVIRIS subscene simulated with a plant canopy radiative transfer model. The simulated subscene is spatially patterned after a subscene from the AVIRIS image acquired August, 1993 over La Copita, Texas. In addition, for comparison, we performed a traditional unmixing with image endmembers.

Bateson, C. Ann↗
NASA NTRS2001

The Transient Dendritic Solidification Experiment (TDSE)

Dendritic solidification is a common mode of solidification. It is also an important model problem in nonequilibrium physics and pattern formation physics. Current theories couple the transfer of latent heat with selection mechanisms at the interface. Measurements of succinonitrile (SCN) dendrites in microgravity show reasonable agreement between heat transfer predictions and experiment. However, data and analysis for assessing interfacial physics theories are less definitive. We are studying, and will present data on, transient effects in dendritic growth of SCN. We employ the Clapeyron pressure/melting temperature effect to make a rapid change in a sample's hydrostatic pressure, and thereby rapidly change the specimen's melting temperature, forcing the dendrite to select a new steady-state. These initial measurements show some surprising and non-intuitive effects.

Koss, M. B.↗
NASA NTRS2004

Micro-Scale Regenerative Heat Exchanger

A micro-scale regenerative heat exchanger has been designed, optimized and fabricated for use in a micro-Stirling device. Novel design and fabrication techniques enabled the minimization of axial heat conduction losses and pressure drop, while maximizing thermal regenerative performance. The fabricated prototype is comprised of ten separate assembled layers of alternating metal-dielectric composite. Each layer is offset to minimize conduction losses and maximize heat transfer by boundary layer disruption. A grating pattern of 100 micron square non-contiguous flow passages were formed with a nominal 20 micron wall thickness, and an overall assembled ten-layer thickness of 900 microns. Application of the micro heat exchanger is envisioned in the areas of micro-refrigerators/coolers, micropower devices, and micro-fluidic devices.

Moran, Matthew E.↗
DOE OSTI2023

Numerical Study of Liquid Piston Compression Using Large-Eddy Simulation and Volume-of-Fluid Approach

Efforts to increase the efficiency of residential and commercial air conditioners and heat pumps have demonstrated that the compressor accounts for most of the system’s electrical energy usage. Therefore, the efficiency of this component should be improved to reduce its energy usage. The US Department of Energy’s Oak Ridge National Laboratory developed a near-isothermal liquid piston compressor (LPC) that uses propylene glycol (PG) to compress CO2. This report presents numerical studies of the LPC in which the compression chamber fills with injected PG from the bottom inlet. Numerical simulations were performed using the large-eddy simulation (LES) with the wall-adapting local eddy-viscosity (WALE) subgrid-scale model coupled with the multiphase volume-of-fluid (VOF) model to simulate the transient interface between gas and liquid and to capture the heat and mass transfer within the compression chamber. In this effort, effects of boundary conditions applied to the LES-VOF calculations (e.g., no wall, an adiabatic wall, and a wall with a heat flux subscribed) to the overall pressure and temperature of CO2 gas as well as the transient evolution of flow and heat transfer evolution within the compression chamber are investigated and discussed. It was found that the LES calculation with no wall have shown no dynamical flow patterns and the volume-averaged temperature of CO2 increased from 305 to 392.7 K, while LES calculations with a constant wall temperature or a wall heat flux had similar increases of CO2 temperatures. Results of LES simulation using a wall heat flux showed different stages in the compression process and revealed dynamical formation and interaction of CO2 gas layers and circulation flow patterns within the chamber that contribute to the overall heat transfer between the solid wall, gas, and liquid surface in the compressor.

Nguyen, Thien D.↗