Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “parameter reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Shock Wave Dynamics in Weakly Ionized Gases

We have begun a comprehensive series of analyses and experiments to study the basic problem of shock wave dynamics in ionized media. Our objective is to isolate the mechanisms that are responsible for the decrease in the shock amplitude and also to determine the relevant plasma parameters that will be required for a drag reduction scheme in an actual high altitude hypersonic flight. Specifically, we have initiated a program of analyses and measurements with the objective of (i) fully characterizing the propagation dynamics in plasmas formed in gases of aerodynamic interest, (ii) isolating the mechanisms responsible for the decreased shock strength and increased shock velocity, (iii) extrapolating the laboratory observations to the technology of supersonic flight.

Johnson, Joseph A., III↗
NASA NTRS1988

Salinity stress inhibits bean leaf expansion by reducing turgor, not wall extensibility

Treatment of bean (Phaseolus vulgaris L.) seedlings with low levels of salinity (50 or 100 millimolar NaCl) decreased the rate of light-induced leaf cell expansion in the primary leaves over a 3 day period. This decrease could be due to a reduction in one or both of the primary cellular growth parameters: wall extensibility and cell turgor. Wall extensibility was assessed by the Instron technique. Salinity did not decrease extensibility and caused small increases relative to the controls after 72 hours. On the other hand, 50 millimolar NaCl caused a significant reduction in leaf bulk turgor at 24 hours; adaptive decreases in leaf osmotic potential (osmotic adjustment) were more than compensated by parallel decreases in xylem tension potential and the leaf apoplastic solute potential, resulting in a decreased leaf water potential. It is concluded that in bean seedlings, mild salinity initially affects leaf growth rate by a decrease in turgor rather than by a reduction in wall extensibility. Moreover, long-term salinization (10 days) resulted in an apparent mechanical adjustment, i.e. an increase in wall extensibility, which may help counteract reductions in turgor and maintain leaf growth rates.

NASA Discipline Number 40-10↗
NASA NTRS2016

Model Order Reduction of Aeroservoelastic Model of Flexible Aircraft

This paper presents a holistic model order reduction (MOR) methodology and framework that integrates key technological elements of sequential model reduction, consistent model representation, and model interpolation for constructing high-quality linear parameter-varying (LPV) aeroservoelastic (ASE) reduced order models (ROMs) of flexible aircraft. The sequential MOR encapsulates a suite of reduction techniques, such as truncation and residualization, modal reduction, and balanced realization and truncation to achieve optimal ROMs at grid points across the flight envelope. The consistence in state representation among local ROMs is obtained by the novel method of common subspace reprojection. Model interpolation is then exploited to stitch ROMs at grid points to build a global LPV ASE ROM feasible to arbitrary flight condition. The MOR method is applied to the X-56A MUTT vehicle with flexible wing being tested at NASA/AFRC for flutter suppression and gust load alleviation. Our studies demonstrated that relative to the fullorder model, our X-56A ROM can accurately and reliably capture vehicles dynamics at various flight conditions in the target frequency regime while the number of states in ROM can be reduced by 10X (from 180 to 19), and hence, holds great promise for robust ASE controller synthesis and novel vehicle design.

aeroelasticity↗
NASA NTRS1981

Forebody drag reduction

It is shown that the mechanisms of forebody drag reduction by means of either a spike or a forward-facing jet are similar, with the maximum achievable drag reduction being of the same order. Because the jet may be a relatively cool gas, however, the forward facing jet has the additional capability of reducing the aerodynamic heating that is so severe at high Mach numbers. By means of the correlation presented, jet ejection parameters may be chosen to achieve maximum permissible forebody drag reduction. The correlation method uses a momentum coefficient that characterizes jet efflux and freestream conditions.

Pamadi, B. N.↗
NASA NTRS2008

GRCop-84 Rolling Parameter Study

This report is a section of the final report on the GRCop-84 task of the Constellation Program and incorporates the results obtained between October 2000 and September 2005, when the program ended. NASA Glenn Research Center (GRC) has developed a new copper alloy, GRCop-84 (Cu-8 at.% Cr-4 at.% Nb), for rocket engine main combustion chamber components that will improve rocket engine life and performance. This work examines the sensitivity of GRCop-84 mechanical properties to rolling parameters as a means to better define rolling parameters for commercial warm rolling. Experiment variables studied were total reduction, rolling temperature, rolling speed, and post rolling annealing heat treatment. The responses were tensile properties measured at 23 and 500 C, hardness, and creep at three stress-temperature combinations. Understanding these relationships will better define boundaries for a robust commercial warm rolling process. The four processing parameters were varied within limits consistent with typical commercial production processes. Testing revealed that the rolling-related variables selected have a minimal influence on tensile, hardness, and creep properties over the range of values tested. Annealing had the expected result of lowering room temperature hardness and strength while increasing room temperature elongations with 600 C (1112 F) having the most effect. These results indicate that the process conditions to warm roll plate and sheet for these variables can range over wide levels without negatively impacting mechanical properties. Incorporating broader process ranges in future rolling campaigns should lower commercial rolling costs through increased productivity.

Loewenthal, William S.↗
NASA NTRS1980

Progress report on the Block 1 VLBI correlator implementation

The Block 1 VLBI Processor Subsystem (VPS) of the Very Long Baseline Interferometry (VLBI) System for the determination of station clock-sync parameters, UT1 and polar motion, and station platform parameters and for use in spacecraft tracking is discussed. The Block 1 VPS performs three basic functions: it receives the 500 kbit/sec video data over the GCF wideband data lines from each of the three DSN 64 m antennas; it cross correlates data; and it performs several postcorrelation data reduction operations on the correlated data including calibration, editing, and parameter estimation.

Peterson, J. C.↗
NASA NTRS1986

Concepts for reduction of blade-vortex interaction noise

A model is developed to determine the critical parameters that control noise generation by blade-vortex interaction (BVI). The equations for evaluation BVI are derived. The analysis of BVI using the model reveals that the interaction is dependent on incoming vortex strength, blade lift, the interaction length, and the miss distance of the interaction. Several methods for reduction of the noise source are proposed.

Hardin, J. C.↗
NASA NTRS1989

Controller reduction by preserving impulse response energy

A model order reduction algorithm based on a Krylov recurrence formulation is developed to reduce order of controllers. The reduced-order controller is obtained by projecting the full-order LQG controller onto a Krylov subspace in which either the controllability or the observability grammian is equal to the identity matrix. The reduced-order controller preserves the impulse response energy of the full-order controller and has a parameter-matching property. Two numerical examples drawn from other controller reduction literature are used to illustrate the efficacy of the proposed reduction algorithm.

Craig, Roy R., Jr.↗
NASA NTRS2003

Magnetogasdynamic Power Extraction and Flow Conditioning for a Gas Turbine

An extension of the Russian AJAX concept to a turbojet is being explored. This magnetohydrodynamic (MHD) energy bypass engine cycle incorporating conventional gas turbine technology has MHD flow conditioning at the inlet to electromagnetically extract part of the inlet air kinetic energy. The electrical power generated can be used for various on-board vehicle requirements including plasma flow control around the vehicle or it may be used for augmenting the expanding flow in the high speed nozzle by MHD forces to generate more thrust. In order to achieve this interaction, the air needs to be ionized by an external means even up to fairly high flight speeds, and the leading candidates may be classified as electrical discharge devices. The present kinetic modeling calculations suggest that the use of electron beams with characteristics close to the commercially available e-beam systems (electron energy approx. 60 keV, beam current approx. 0.2 mA/sq cm) to sustain ionization in intermediate pressure, low-temperature (P = 0.1 atm, T = 300 K) supersonic air flows allows considerable reduction of the flow kinetic energy (up to 10 to 20 percent in M = 3 flows). The calculations also suggest that this can be achieved at a reasonable electron beam efficiency (eta approx. 5), even if the e-beam window losses are taken into account. At these conditions, the exit NO and O atom concentrations due to e-beam initiated chemical reactions do not exceed 30 ppm. Increasing the beam current up to approx. 2 mA/sq cm, which corresponds to a maximum electrical conductivity of sigma(sub max) approx. 0.8 mho/m at the loading parameter of K = 0.5, would result in a much greater reduction of the flow kinetic energy (up to 30 to 40 percent). The MHD channel efficiency at these conditions would be greatly reduced (to eta approx. 1) due to increased electron recombination losses in the channel. At these conditions, partial energy conversion from kinetic energy to heat would result in a significant total pressure loss (P(sub 0)/P(sub 0i) approx. 0.3). The total pressure loss can be reduced operating at the loading parameter closer to unity, at the expense of the reduced electrical power output. Raising the beam current would also result in the increase of the exit O atom concentrations (up to 600 ppm) and NO (up to 150 ppm).

Adamovich, Igor V.↗
NASA NTRS1987

State-space formulation of multi-shaker modal analysis

As modal testing techniques have improved in recent years, the demands placed on the accuracy of modal test results have increased. This paper describes a new multi-input, multi-output modal parameter estimation algorithm suitable for the identification of reduced-order models of structures. The method described is a frequency-domain method based on excitation and response spectra. The principal features of the algorithm are: (1) applicability to general linear, time-invariant systems, (2) direct use of multiple input and multiple response data, (3) identification of reduced-order models with minimum user interaction through the use of two automatic model-reduction techniques, (4) identification of a consistent set of modal parameters through the use of numerically stable least-squares techniques, and (5) complete user documentation.

Craig, Roy R., Jr.↗
NASA NTRS1992

Reynolds number dependence of the freestream turbulence effects on turbulent boundary layers

Published experimental data on the influence of freestream turbulence on turbulent boundary layers were examined to determine the effect of Reynolds number on such influence. Two manifestations of the effect of low Reynolds numbers on the outer layer were observed: (1) the dependence of Clauser's shape parameter G on Reynolds number at very low Reynolds numbers and (2) the reduction in the wake component due to freestream turbulence undergoing a reversal in the Reynolds number dependence. These observations were used to modify Hancock's (1980) freestream turbulence parameter.

Bandyopadhyay, Promode R.↗
NASA NTRS2023

AMORE-Isoprene v1.0: A New Reduced Mechanism for Gas-Phase Isoprene Oxidation

Gas-phase oxidation of isoprene by ozone (O 3 ) and the hydroxyl (OH) and nitrate (NO 3 ) radicals significantly impacts tropospheric oxidant levels and secondary organic aerosol formation. The most comprehensive and up-to-date chemical mechanism for isoprene oxidation consists of several hundred species and over 800 reactions. Therefore, the computational expense of including the entire mechanism in large-scale atmospheric chemical transport models is usually prohibitive, and most models employ reduced isoprene mechanisms ranging in size from ∼ 10 to ∼ 200 species. We have developed a new reduced isoprene oxidation mechanism using a directed-graph path-based automated model reduction approach, with minimal manual adjustment of the output mechanism. The approach takes as inputs a full isoprene oxidation mechanism, the environmental parameter space, and a list of priority species which are protected from elimination during the reduction process. Our reduced mechanism, AMORE-Isoprene (where AMORE stands for Automated Model Reduction), consists of 12 species which are unique to the isoprene mechanism as well as 22 reactions. We demonstrate its performance in a box model in comparison with experimental data from the literature and other current isoprene oxidation mechanisms. AMORE-Isoprene's performance with respect to predicting the time evolution of isoprene oxidation products, including isoprene epoxydiols (IEPOX) and formaldehyde, is favorable compared with other similarly sized mechanisms. When AMORE-Isoprene is included in the Community Regional Atmospheric Chemistry Multiphase Mechanism 1.0 (CRACMM1AMORE) in the Community Multiscale Air Quality Model (CMAQ, v5.3.3), O 3 and formaldehyde agreement with Environmental Protection Agency (EPA) Air Quality System observations is improved. O 3 bias is reduced by 3.4 ppb under daytime conditions for O 3 concentrations over 50 ppb. Formaldehyde bias is reduced by 0.26 ppb on average for all formaldehyde measurements compared with the base CRACMM1. There was no significant change in computation time between CRACMM1AMORE and the base CRACMM. AMORE-Isoprene shows a 35 % improvement in agreement between simulated IEPOX concentrations and chamber data over the base CRACMM1 mechanism when compared in the Framework for 0-D Atmospheric Modeling (F0AM) box model framework. This work demonstrates a new highly reduced isoprene mechanism and shows the potential value of automated model reduction for complex reaction systems.

Automated Model Reduction↗
NASA NTRSDate not supplied

A Procedure for Obtaining Forecast Turbulence Parameters in the Atmospheric Boundary Layer for Acoustic Propagation

Propagation through turbulence causes a mean reduction in loudness of sonic booms and in some cases can cause significant fluctuations in loudness about that mean. Understanding these effects is important for accurately planning loudness levels during upcoming community noise tests with the X-59 aircraft as well as mitigating the risk for excessive loudness due to turbulence. Current methods for modeling acoustic propagation through turbulence require several atmospheric parameters including the atmospheric boundary layer (ABL) height, friction velocity, mixed-layer velocity scale, surface-layer temperature scale, as well as ambient pressure, temperature, and humidity within the ABL. Accurate forecasts of these parameters are needed for X-59 flight planning and may also be useful for planning future supersonic aircraft certification flight tests. This presentation showcases one method for obtaining the forecast turbulence and ambient atmospheric parameters from freely available Climate Forecast System Version 2 data. Forecast parameters are compared to measurements to assess accuracy and utility.

sonic boom↗
NASA NTRS1972

Bonanza project, 1971

Research on the application of remote sensing techniques to the mineral industry stresses photointerpretation by human interpreter experienced in the extraction of geological information from aerial color and multiband photographs and from thermal scanner imagery. Also considered are optical and digital image enhancement, multiband color additive projection, video image processing, and computer reduction and analysis of infrared spectrometry. Evaluation of those parameters which have the most contrast between adjacent rock formations and which can be remotely sensed establish the following most useful geological characteristics: Topographic landform, color, albedo, and surface temperature.

Lee, K.↗
NASA NTRS1983

Integrated atmosphere revitalization system description and test results

The design and operation of several air revitalization subsystems are described, along with the testing of these subsystems separately and integrated in an air revitalization system for use in space stations. The subsystems are: one that generates O2 by water electrolysis, one that removes and concentrates CO2 using an electrochemical technique, and one that reduces concentrated CO2 by the Sabatier process. Results of the integrated testing include the observations that liquid cooling should be baselined for recovery of the CO2 reduction subsystem product water, continuous CO2 injection into the air supply unit is preferable, small changes in the current CO2 removal subsystem inlet PCO2 are detectable as changes in the CO2 reduction subsystem reactor temperatures, and hardwired shutdown of critical parameters is vital if computer-based controllers are not redundant. Several block diagrams are provided.

Martin, R. B.↗