Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “outdoor testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Test stand performance of a convertible engine for advanced V/STOL and rotorcraft propulsion

A variable inlet guide vane (VIGV) convertible engine that could be used to power future high-speed V/STOL and rotorcraft was tested on an outdoor stand. The engine ran stably and smoothly in the turbofan, turboshaft, and dual (combined fan and shaft) power modes. In the turbofan mode with the VIGV open, fuel consumption was comparable to that of a conventional turbofan engine. In the turboshaft mode with the VIGV closed, fuel consumption was higher than that of present turboshaft engines because power was wasted in churning fan-tip air flow. In dynamic performance tests with a specially built digital engine control and using a waterbrake dynamometer for shaft load, the engine responded effectively to large steps in thrust command and shaft torque.

Mcardle, Jack G.↗
DOE OSTI2022

A study of degradation mechanisms in PVDF-based photovoltaic backsheets

Abstract Commercial backsheets based on polyvinylidene fluoride (PVDF) can experience premature field failures in the form of outer layer cracking. This work seeks to provide a better understanding of the changes in material properties that lead to crack formation and find appropriate accelerated tests to replicate them. The PVDF-based backsheet outer layer can have a different structure and composition, and is often blended with a poly(methyl methacrylate) (PMMA) polymer. We observed depletion of PMMA upon aging with sequential (MAST) and combined (C-AST) accelerated stress testing. In field-aged samples from Arizona and India, where PVDF crystallizes in its predominant α-phase, the degree of crystallinity greatly increased. MAST and C-AST protocols were, to some extent, able to replicate the increase in crystallinity seen in PVDF after ~ 7 years in the field, but no single-stress test condition (UV, damp heat, thermal cycling) resulted in significant changes in the material properties. The MAST regimen used here was too extreme to produce realistic degradation, but the test was useful in discovering weaknesses of the particular PVDF-based outer layer structure studied. No excessive β-phase formation was observed after aging with any test condition; however, the presence of β-phase was identified locally by Fourier transform infrared spectroscopy (FTIR). We conclude that both MAST and C-AST are relevant tests for screening outdoor failure mechanisms in PVDF backsheets, as they were successful in producing material degradation that led to cracking.

14 SOLAR ENERGY↗
DOE OSTI2022

CSP Optical Facilities at the National Renewable Energy Laboratory

The concentrating Solar Power (CSP) Optical Facilities at NREL comprise unique optical tools and facilities for testing and characterizing concentrating solar optical components. These facilities are maintained to aid researchers and industry efforts to reduce market barriers, improve the performance, reduce the cost, and improve the lifetime and reliability of CSP materials, components, subsystems, and integrated concepts, where accurate and timely characterization methods are needed. To reach this goal, NREL is committed to collaborating in ongoing and projected research needs for industry, academia, and government entities, in the development and characterization of low-cost, high-performance reflector and absorber materials in addition to their components-a key element in the conversion of concentrated sunlight into energy. To accomplish this mission, the core laboratory includes the Advanced Optical Materials Laboratory, indoor and outdoor accelerated weather testing tools, "Distant Observer" for parabolic troughs, the High Flux Solar Furnace, and the ultra-accelerated weather testing tools. This equipment enables to rapidly respond to new challenges with novel solutions that align with the goals of the Solar Energy Technology Office (SETO) at the U.S. Department of Energy. The goal of this paper is to present the state-of art-optical facilities available at NREL that can help support the research needs of the CSP community. Therefore, we review here the different components of the CSP Optical Facilities at NREL and highlight their characteristics and importance for the CSP community.

accelerated weather testing↗
NASA NTRS1973

Noise comparisons from full-scale fan tests at NASA Lewis Research Center

The overall aero and acoutic design features of eight 6-foot-diameter, single stage fans tested in an outdoor acoustic facility are described. A correlation of the acoustic results for subsonic tip-speed fans showed the total sound power was proportional to the mechanical power imparted to the fan and the specific work performed on the air to within + or - 2 dB. The correlation was relatively insensitive to fan design variables over a broad range of operating conditions. Maximum perceived noise levels were generally proportional to the sound power levels with both noise levels exhibiting a relatively unique increase with fan pressure ratio when normalized by the delivered thrust.

Heidmann, M. F.↗
NASA NTRS1973

Noise comparisons from full-scale fan tests at NASA Lewis Research Center.

The overall aero and acoustic design features of eight 6-foot-diameter, single-stage fans tested in an outdoor acoustic facility are described. A correlation of the acoustic results for subsonic tip-speed fans showed the total sound power to be proportional to the mechanical power imparted to the fan and the specific work performed on the air to within plus or minus 2 dB. The correlation was relatively insensitive to fan design variables over a broad range of operating conditions. Maximum perceived noise levels were generally proportional to the sound power levels with both noise levels exhibiting a relatively unique increase with fan pressure ratio when normalized by the delivered thrust. The spectra of broadband noise attributed to the fan exhibited a bimodal characteristic for most of the fans. A predominant mode centered near the blade-passage tone and another at 8 to 16 times the tone frequency.

Heidmann, M. F.↗
NASA NTRS1976

Acoustic and aerodynamic effects of rotor pitch angle for a variable-pitch, 6-foot diameter fan stage

An externally driven, 1.2 pressure ratio full-scale fan stage with an adjustable pitch rotor was tested in an outdoor facility at the Lewis Research Center. Rotor pitch angles resulting in minimum sideline perceived noise levels are defined as a function of stage thrust. Thrust-corrected fan noise variations are examined for operation at constant thrust, rotor tip speed, and stage work coefficient. At constant stage thrust, reducing the rotor pitch angle below design values increased the fan noise with the greatest change occurring in the blade passing tone level. At constant fan speed the minimum noise occurred at a particular rotor pitch angle, which was not the minimum thrust condition. With constant stage work coefficient, rear quadrant noise increased at above-design speed conditions.

Woodward, R. P.↗
NASA NTRS1976

Outdoor performance results for NBS Round Robin collector no. 1

The efficiency of a PPG flat-plate solar collector was evaluated utilizing an outdoor solar collector test facility at the NASA-Lewis Research Center, as part of the National Bureau of Standards 'round robin' collector test program. The correlation equation for collector thermal efficiency Eta curve fit of the data was: Eta = 0.666 - 1.003(Btu/hr-sq ft-F) Theta, where the parameter Theta is the difference between the average fluid temperature and the ambient temperature, all divided by the total flux impinging on the collector.

Miller, D. R.↗
NASA NTRS1991

Laser Velocimeter For Outdoor Or Wind-Tunnel Measurements

Laser velocimeter developed for remotely controlled operation in large wind tunnel or at outdoor aircraft-testing site. Long-range laser velocimeter has expanded focal range and ability to measure two perpendicular components of velocity simultaneously. Includes electronic subsystems for control and acquisition of data.

Reinath, Michael S.↗
NASA NTRS1993

Performance results from a test of an S-76 rotor in the NASA Ames 80- by 120-foot wind tunnel

A full-scale helicopter rotor wind tunnel test has been conducted which covers a wide range of rotor-shaft angles-of-attack and 0-100 kt thrust conditions. The hover performance data thus obtained were compared with the results of momentum theory calculations; forward flight rotor-performance data were compared with calculations from a comprehensive rotorcraft analysis. These comparisons suggest that hover testing at an outdoor facility in the absence of ground effect is required to make a final determination of the absolute accuracy of the wind tunnel hover data.

Shinoda, Patrick M.↗
NASA NTRSDate not supplied

A Microphone Phased Array for Launch Acoustics Application

A new, portable, phased array of microphones is built at NASA Ames Research Center specifically for the harsh environment encountered in launch pads of rocket vehicles. It uses 70 piezoresistive, dynamic pressure sensors, optimally distributed on a 10.5ft diameter open frame dome structure. The open frame is light yet robust to sustain the high wind load of typical seaside launch pads, and the blast and acoustic loads from the launch. A 200-ft long cable bundle carries the microphone signals to a weather-protected cabinet containing the data systems, and allows for the placement of the array tall structures. The array is equipped with an infra-red camera and a visible wavelength camera for imaging the launch pad. The beamformed noise maps will be superimposed on the video footages collected by the cameras for correct identification of the noise sources. The array is tested with very loud speaker sources to determine the beamforming ability using different schemes, such as the conventional beamforming, orthogonal-functional beamforming, and spectral element methods. A comparative study was conducted to determine the minimum attainable spatial resolution. Data from a validation test in an outdoor setup, where the array was placed on a Telehandler at several different heights and distances from either a single or a pair of speakers, is presented in this paper. The final goal is to use the array during NASA’s Artemis-II launch to determine the distribution of noise sources on the Mobile Launcher.

Acoustics↗
DOE OSTI2023

Medium-Voltage Testbed for Comparing Advanced Power Line Sensors vs. Measurement Transformers with Electrical Grid Events

Electrical utilities have relied upon potential transformers (PTs) and current transformers (CTs) for very accurate metering and to provide reliable signals for protective relays. Less expensive alternative sensing technologies offer the possibility of wider deployment, particularly in grids that employ distributed energy resources. In this work, the performance of an advanced medi-um-voltage sensor is compared with a reference PT and CT and experimentally evaluated for different power grid scenarios on an advanced outdoor power line sensor testbed at the US De-partment of Energy’s Oak Ridge National Laboratory. The sensor is based on a capacitive divider for voltage monitoring and a Rogowski coil with integrator for current monitoring. The advanced outdoor power line sensor testbed has a real-time simulator that was used to generate transient scenarios (e.g., electrical faults, capacitor bank operation, service restoration), while the analog signals were recorded by the same high resolution power meter. The behavior of analog signals, harmonic components, total harmonic distortion, and crest factors were assessed for this power line sensor compared with the reference PT/CT, because of the absence for testing standards for advanced outdoor power line sensors.

Piesciorovsky, Emilio↗
NASA NTRS1973

Evaluation of Stress Corrosion Cracking Susceptibility Using Fracture Mechanics Techniques, Part 1

Stress corrosion cracking (SSC) tests were performed on 13 aluminum alloys, 13 precipitation hardening stainless steels, and two titanium 6Al-4V alloy forgings to compare fracture mechanics techniques with the conventional smooth specimen procedures. Commercially fabricated plate and rolled or forged bars 2 to 2.5-in. thick were tested. Exposures were conducted outdoors in a seacoast atmosphere and in an inland industrial atmosphere to relate the accelerated tests with service type environments. With the fracture mechanics technique tests were made chiefly on bolt loaded fatigue precracked compact tension specimens of the type used for plane-strain fracture toughness tests. Additional tests of the aluminum alloy were performed on ring loaded compact tension specimens and on bolt loaded double cantilever beams. For the smooth specimen procedure 0.125-in. dia. tensile specimens were loaded axially in constant deformation type frames. For both aluminum and steel alloys comparative SCC growth rates obtained from tests of precracked specimens provide an additional useful characterization of the SCC behavior of an alloy.

Sprowls, D. O.↗
NASA NTRS1992

Hover performance validation of an ejector configured STOVL fighter aircraft

The hover thrust performance of a full-scale model of an ejector-lift/vectored thrust Short Take-Off and Vertical Landing (STOVL) fighter configuration was measured at the Outdoor Aerodynamic Research Facility of the National Full-Scale Aerodynamics Complex located at NASA Ames Research Center. The static thrust of the lifting ejector and ventral nozzle was calibrated at an out-of-ground-effect height. The test permitted comparison with static thrust calibrations obtained in the 80- by 120-Foot Wind Tunnel. The average static thrust augmentation ratio of the ejector system was 1.55 compared with the design goal of 1.63. The outdoor test showed that the addition of short extensions to the diffuser on the fuselage sidewall decreased suckdown and increased ejector performance. As expected, an increase in the ventral nozzle thrust deflection angle from nearly horizontal to the vertical-lift hover position caused a significant decrease in thrust. Flow visualization using smoke revealed greater secondary airflow into the left ejector and the penetration of hot ventral gases along the ground beneath and between the cool plumes from the ejector system.

Naumowicz, Tim↗
NASA NTRS1986

Tests of Solar-Array Encapsulants

Materials tested for degradation by heat and light. Report presents early results of continuing series of photothermal aging tests of some candidate encapsulating materials for solar photovoltaic modules. Objectives of testing program: contribute to development of durable, low-cost encapsulants and predict lifetimes of encapsulated photovoltaic modules placed outdoors. Toward these ends, tests designed to reveal physical and chemical degradation mechanisms that affect encapsulants.

Liang, R. H.↗
NASA NTRS1977

Evaluation of the in-flight noise signature of a 32-chute suppressor nozzle: Acoustic data report

Outdoor static and 40 x 80 FT wind tunnel tests of the J79-15 engine/nacelle system with the conic nozzle and 32-chute exhaust suppressor were conducted to acquire the data necessary to evaluate the simulated in-flight signature of an engine-size 32-chute exhaust nozzle suppressor using the 40 x 80 ft wind tunnel and to study possible engine core noise contamination of the jet signature. The tests are described and and a sampling of the data acquired is presented. Included are aero performance summaries, as-measured and composite 1/3 OBSPL spectra for the 70 ft sideline high and low mics from the outdoor static tests, sideline traverse spectra and internal noise measurements from both the outdoor static and the 40 x 80 ft wind tunnel tests.

Moore, M. T.↗
NASA NTRS1976

Photovoltaic Test and Demonstration Project

The Photovoltaic Test and Demonstration Project was initiated by NASA in June, 1975, to develop economically feasible photovoltaic power systems suitable for a variety of terrestrial applications. Objectives include the determination of operating characteristic and lifetimes of a variety of solar cell systems and components and development of methodology and techniques for accurate measurements of solar cell and array performance and diagnostic measurements for solar power systems. Initial work will be concerned with residential applications, with testing of the first prototype system scheduled for June, 1976. An outdoor 10 kW array for testing solar power systems is under construction.

Forestieri, A. F.↗
NASA NTRS1975

Outdoor flat-plate collector performance prediction from solar simulator test data

Solar collector performance data obtained from tests with a simulator was modified for real-life conditions. The data obtained with the simulator was corrected for the variable conditions of ambient temperature, wind, incident angle, flow rate, etc., that are encountered outdoors. Modification of simulator data was accomplished by combining experiment with theory. The technique was demonstrated by application to a spectrally selective and a nonselective type of collector. This kind of modified simulator collector performance data should be valuable in solar systems analysis and for collector performance ranking based on all-day calculated conditions.

Simon, F. F.↗