Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Multi-objective surrogate-assisted calibration of CPFEM models using macroscopic response and in situ EBSD measurements of grain reorientation trajectories

Crystal plasticity finite element method (CPFEM) models are widely used to simulate the deformation behaviour of polycrystalline materials, but their calibration is often limited by their high computational cost and the non-convexity of the optimisation landscape. Here, this study develops a multi-objective surrogate-assisted calibration workflow that couples a multi-objective genetic algorithm (MOGA) with an adaptively trained deep neural network (DNN) surrogate model to efficiently identify CPFEM parameters from experimental data. The workflow is demonstrated on three crystal plasticity (CP) formulations of increasing complexity — Voce hardening (VH), two-coefficient latent hardening (LH2), and six-coefficient latent hardening (LH6) — using in situ electron backscatter diffraction (EBSD) measurements of Alloy 617 under uniaxial tensile loading. The CPFEM models are calibrated against the experimentally observed stress–strain response and reorientation trajectories of eight grains, then validated against eight additional trajectories and overall texture evolution. Across the CP formulations, the macroscopic response was reproduced reliably, while differences emerged in the robustness and accuracy of the grain-scale predictions. Including grain reorientation trajectories in the multi-objective calibration improved texture evolution predictions and filtered out physically inconsistent parameter sets that can arise from calibrating against only the stress–strain data. The workflow also demonstrates good transferability of calibrated parameters from a low- to a high-fidelity microstructural model. These results provide practical guidance for integrating in situ microstructural data into CPFEM through efficient, repeatable, and physically meaningful multi-objective calibration.

Crystal plasticity finite element method↗

Materials Dynamics

The Materials Dynamics area of leadership focuses on understanding structure-properties-performance relationships for the extreme conditions of dynamic loading. This research encompasses controlled synthesis of materials to meet dynamic performance requirements and requires computational coupling across length and time scales for three-dimensional microstructure modeling. For this leadership area, we define dynamic loading as strain rates greater than 103/s. A key grand challenge of this area is to predict and measure the evolution of microstructural phases, defect structures, and electronic structure under dynamic conditions while also dynamically measuring local temperature to understand transition states. Solving this challenge will require agile, multidimensional data analysis and interpretation capability.

36 MATERIALS SCIENCE↗

Materials Dynamics

The Materials Dynamics area of leadership focuses on understanding process-structure-properties-performance (PSPP) relationships for the extreme conditions of dynamic loading. This research encompasses controlled synthesis of materials to meet dynamic performance requirements and entails computational coupling across length and time scales for three-dimensional microstructure modeling. For this leadership area, we define dynamic loading as strain rates ≥ 10 3 /s and often, high pressures. A key grand challenge of this area is to predict and measure the evolution of microstructural phases, defect structures, and electronic structure under dynamic conditions while also measuring local temperature to understand transition states. Solving this challenge will require agile, multi-dimensional data analysis and interpretation capability.

36 MATERIALS SCIENCE↗

Effect of Martensite Content on Failure Behavior of Laser Welded Dual-Phase Steel Joints During Deformation

Laser welding was applied to three types of dual-phase (DP) steel sheets (DP590, DP780, and DP980) with different martensite contents. The microstructure of laser welded joints was observed by optical microscope and scanning electron microscope, and the hardness of welded joints was measured by a microhardness tester. The tensile testing machine and the Erichsen test machine were employed to measure the tensile properties and forming properties of welded joints, respectively. The microstructure model showed that the welded joints of three different materials all contained a hardened zone (HZ) that was composed of a fusion zone, a coarse-grained heat-affected zone, and fine-grained heat-affected zone. The microstructure of the HZ contained mainly martensite such that the average martensite content of welded joints was increased by 1.9-9.8%, and the microhardness of the HZ was 1.2-1.9 times that of the base metal (BM). Moreover, the elongation of welded joints decreased with decreasing martensite content in the BM, and the effect was severe for the DP590 welded joint (21.8%) compared to the other two welded joints. During the Erichsen test, deformation failure varied among the welded joints with different martensite contents, and it was determined by the HZ and softened zone. The fracture occurred in the softened zone and ran parallel along the zone for DP980 welded joints, whereas the fracture occurred in the HZ and ran perpendicular to this zone for the other two welded joints. The Erichsen values of the DP590, DP780, and DP980 welded joints were 81.1, 91.7, and 85.0% of the BM, respectively.

36 MATERIALS SCIENCE↗

Microstructure and nanoindentation of the rostrum of Curculio longinasus Chittenden, 1927 (Coleoptera: Curculionidae)

The rostrum is an extension of the cuticle of the head of weevils (Coleoptera: Curculionidae) and is often used to bore holes for oviposition (the process of laying eggs) into host plant tissue where larval development occurs. In members of the genus Curculio Linnaeus, 1758, the rostrum is long, slender, and strongly curved, but is nevertheless used to excavate straight bore-holes in the fruit of various host plants, through significant deformation of this structure. In this study, scanning electron microscopy (SEM) was used to examine the rostrum of Curculio longinasus Chittenden, 1927, leading to a microstructural model that describes its deformation behavior. Specifically, we used the continuous stiffness measurement (CSM) technique in nanoindentation to measure the Young's modulus and hardness of rostrum. The values of Young's modulus and hardness for the endocuticle were measured to be 8.91 ± 0.93 GPa and 558 ± 60 MPa, respectively. These results are critical for generating accurate finite element models of the head's mechanical behavior while it undergoes deformation. - Highlights: •SEM was used to examine the rostrum of Curculio longinasus Chittenden, 1927. •Nanoindentation to measure the Young's modulus and hardness of rostrum. •Results are critical for finite element models of the head's mechanical behavior.

36 MATERIALS SCIENCE↗

Real-time microstructure of shocked LiF crystals: Use of synchrotron x-rays

We describe the use of a third generation synchrotron facility to obtain in situ, real-time, x-ray diffraction measurements in plate impact experiments. Subnanosecond duration x-ray pulses were utilized to record diffraction data from pure and magnesium-doped LiF single crystals shocked along the [111] and [100] orientations. The peak stresses were 3.0 GPa for the [111] oriented LiF and between 3.0 and 5.0 GPa for the [100] oriented LiF. For these stresses, shock compression along [111] results in elastic deformation and shock compression along [100] results in elastic-plastic deformation. Because of the quality of the synchrotron x-ray pulses, both shifting and broadening of the diffraction data were obtained simultaneously. As expected, shifts for elastic compression and elastic-plastic compression in shocked LiF were consistent with uniaxial and isotropic lattice compression, respectively. More importantly, diffraction patterns from crystals shocked along [100] exhibited substantial broadening due to elastic-plastic deformation. The broadening indicates that the shocked LiF(100) crystals developed substructure with a characteristic size for coherently diffracting domains (0.1-10{micro}m) and a distribution of (100) microlattice-plane rotations ({approx} 1{sup o} wide). In contrast to the LiF(100) results, broadening of the diffraction pattern did not occur for elastically deformed LiF(111). Another important finding was that the amount of lattice disorder for shocked LiF(100) depends on the loading history; the broadening was larger for the magnesium-doped LiF(100) (large elastic precursor) than for ultrapure LiF(100) (small elastic precursor) shocked to the same peak stress. The data are simulated by calculating the diffraction pattern from LiF(100) with a model microstructure consisting of coherently diffracting domains. The lattice orientation and longitudinal strain is assumed uniform within domains, but they vary from domain to domain with Gaussian distributions. Simulations using such a model are in good agreement with the measured diffraction patterns. The principal finding from the present work is that synchrotron x-rays can provide real-time data regarding microstructure changes accompanying shock-induced deformation and structural changes.

43 PARTICLE ACCELERATORS↗

Controlling microstructure in deposits fabricated using powder blown direct energy deposition technique

The overall goal of this collaboration is to develop technologies to control grain morphology and microstructures of Inconel 718 components additively manufactured through the Direct Energy Deposition (DED) process (Identical to the LENS (laser engineered net shaping) processes) and to achieve equiaxed or near equiaxed grain structures. The phase1 technical collaboration was used to fabricate Inconel 718 builds with different process parameters, pre heat and scan strategies. The results were then rationalized using computational heat transfer and solidification models. Microstructural characterization showed that the aspect ratio of the grains can be reduced to less than 1.5, and that control of the grain sizes to within 50-100 μm could be potentially obtained by using an external source to preheat the substrate to 400 ̊C. Heat transfer models coupled with solidification models were used to rationalize the results which show that preheating lowered the temperature gradient thereby resulting in moving towards the equiaxed region of the columnar to equiaxed transition (CET) curve. The results demonstrate that higher preheat temperatures could be potentially used to obtain a truly equiaxed structure.

36 MATERIALS SCIENCE↗

Segmentation, statistical analysis, and modelling of the wall system in ceramic foams

Closed walls in otherwise open foam structures may have a great impact on macroscopic properties of the materials. In this paper, we present two algorithms for the segmentation of such closed walls from micro-computed tomography images of the foam structure. The techniques are compared on simulated data and applied to tomographic images of ceramic filters. This allows for a detailed statistical analysis of the normal directions and sizes of the walls. Finally, we explain how the information derived from the segmented wall system can be included in a stochastic microstructure model for the foam.

36 MATERIALS SCIENCE↗

Microstructural-Level Fuel Performance Modeling of U-Mo Monolithic Fuel

As the physics that governs the microstructural evolution of nuclear fuel span various time and spatial scales, to fully understand the fuel behavior inevitably involves atomic to mesoscale resolution that can be difficult to determine experimentally. Microstructural-level modeling and simulations can be used to develop physics-based materials models that can provide physical understanding to inform fabrication process control, as well as a valuable feedback mechanism between post-irradiation examination (PIE) results and fabrication parameters. In accordance with the program schedule, the primary goals of the microstructure modeling effort are to: 1. Address critical microstructural questions and provide practical guidance to the fabricator via the fuel product specification; 2. Provide mechanistic inputs for the existing fuel performance code to improve its descriptive and predictive capability at the macroscopic scale. In fiscal year (FY)-21, the work scope consisted of six main facets: (1) the effect of carbides on fuel performance; (2) gas diffusivity in different phases; (3) integration of microstructural fuel performance modeling; (4) property degradation; (5) irradiation creep; and (6) historical analysis of microstructure data. Brief summaries of each are included below.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DECA: Discrete Event inspired Cellular Automata for grain structure prediction in additive manufacturing

Microstructure largely dictates macroscopic material properties and is strongly affected by processing. Therefore, the simulation of microstructure evolution in response to thermal fields during processing is of significant interest within the computational materials science community. Additive manufacturing (AM) has emerged as a technique for producing complex geometries and unique microstructures. Yet, complex and rapid thermal cycles in AM pose computational challenges for existing microstructure models. This work proposes a discrete event inspired cellular automata (CA) approach, titled DECA, to accelerate simulation of grain structure evolution in AM. In contrast to conventional time-stepped CA models, this model directly solves the times capture events would take place allowing for stepping in events rather than time (a technique also found in the field of discrete-event simulation). In comparison to purely serial discrete-event models, DECA allows for temporary violation of the causality constraint, but detects and corrects these violations, leading to an emergent phenomenon dubbed causality rippling, in which previously calculated capture events are overwritten. The amount of repeated calculations, defined by the capture ratio, is taken as a measure of computational inefficiency, and the model parameters that affect this ratio are evaluated. The new DECA approach was found to be more computationally efficient than conventional time-stepped CA models while guaranteeing an accurate solution, which can only be achieved in the conventional models for vanishingly small time steps. Finally, opportunities for parallelization and scaling of the new approach are discussed.

36 MATERIALS SCIENCE↗

Investigation of Magnetic Signatures and Microstructures for Heat-Treated Ferritic/Martensitic HT-9 Alloy

There is increased interest in improved methods for in-situ nondestructive interrogation of materials for nuclear reactors in order to ensure reactor safety and quantify material degradation (particularly embrittlement) prior to failure. Therefore, a prototypical ferritic/martensitic alloy, HT-9, of interest to the nuclear materials community was investigated to assess microstructure effects on micromagnetics measurements – Barkhausen noise emission, magnetic hysteresis measurements, and first-order reversal curve analysis – for samples with three different heat-treatments. Microstructural and physical measurements consisted of high-precision density, resonant ultrasound elastic constant determination, Vickers microhardness, grain size, and texture. These were varied in the HT-9 alloy samples and related to various magnetic signatures. In parallel, a meso-scale microstructure model was created for alpha iron and effects of polycrystallinity and demagnetization factor were explored. It was observed that Barkhausen noise emission decreased with increasing hardness and decreasing grain size (lath spacing) while coercivity increased. The results are discussed in terms of the use of magnetic signatures for nondestructive interrogation of radiation damage and other microstructural changes in ferritic/martensitic alloys.

Environmental Molecular Sciences Laboratory↗

Microstructure Characterization and Modeling for Improved Electrode Design

This presentation describes research work led by NREL with team members from Argonne National Laboratory and Texas A&M University in microstructure analysis, modeling and validation under DOE's Computer-Aided Engineering of Batteries (CAEBAT) program. The goal of the project is to close the gaps between CAEBAT models and materials research by creating predictive models that can be used for electrode design.

33 ADVANCED PROPULSION SYSTEMS↗

Structurally Integrated Coatings for Wear and Corrosion

Wear and corrosion of structures cuts across industries and continues to challenge materials scientists and engineers to develop cost effective solutions. Industries typically seek mature technologies that can be implemented for production with rapid or minimal development and have little appetite for the longer-term materials research and development required to solve complex problems. The collaborative work performed in this project addressed the complexity of this problem in a multi-year program that industries would be reluctant to undertake without government partnership. This effort built upon the prior development of Advanced Abrasion Resistant Materials conduct by Caterpillar Inc. under DOE Cooperative Agreement No. DE-FC26-01NT41054. In this referenced work, coatings were developed that exhibited significant wear life improvements over standard carburized heat treated steel in abrasive wear applications. The technology used in this referenced work, arc lamp fusing of thermal spray coatings, was one of the primary technical paths in this work effort. In addition to extending the capability of the coating technology to address corrosion issues, additional competitive coating technologies were evaluated to insure that the best technology was developed to meet the goals of the program. From this, plasma transferred arc (PTA) welding was selected as the second primary technology that was investigated. Specifically, this project developed improved, cost effective surfacing materials and processes for wear and corrosion resistance in both sliding and abrasive wear applications. Materials with wear and corrosion performance improvements that are 4 to 5 times greater than heat treated steels were developed. The materials developed were based on low cost material systems utilizing ferrous substrates and stainless steel type matrix with hard particulates formed from borides and carbides. Affordability was assessed against other competing hard surfacing or coating techniques, balanced with overall materials performance. State-of-the-art design and simulation capabilities were used to guide materials and process refinement. Caterpillar was the lead of the multi-partner collaborative project. Specific tasks were performed by the partners base on their unique capabilities. The project team was selected to include leaders in the field of material development, processing, modeling, and material characterization. Specifically, industrial members include the suppliers Deloro Stellite and Powder Alloy Corporation., who provided the experimental alloys and who aided in the development of the costs for the alloys, the Missouri University of Science and Technology and Iowa State University, who provided help in the alloy development and material characterization, QuesTek Innovations, a small company specializing the microstructural modeling of materials, and the DOE laboratories, Oak Ridge National Laboratory and National Energy Technology Laboratory (Albany), who provided unique coating process capability and wear characterization testing. The technologies developed in this program are expected to yield energy savings of about 50% over existing technologies, or 110 trillion BTUs per year by 2020 when fully implemented. Primary applications by Caterpillar are to replace the surface of machine components which are currently carburized and heat treated with new cladding materials with double the wear life. The new cladding technologies will consume less energy than carburizing. Thus, nearly 50% energy savings can be expected as a result from elimination of the heat treat process and the reduce wear of the materials. Additionally, when technologies from this project are applied on titanium or other non-ferrous substrates to make lighter weight, more wear resistant, and more efficient structures, significant fuel savings can be realized. With the anticipated drastic reduction in cost for refining titanium-containing ores, the usage of titanium alloys in earthmoving and related machinery is expected to increase multiple folds in the next decade. A major technical hurdle associated with the implementation of titanium alloys for heavy machinery is that of overcoming poor wear resistance. Proof of concept of the technologies developed in this project has been demonstrated by both laboratory testing of coupons and field testing of selected components. Further development will be required in order to have fully validated materials and process for production introduction and several technical hurdles remain to be addressed particular for use of the arc lamp fusing technology. The current project has reduced the risk of failure and provided sufficient data to encourage further investment by industry.

36 MATERIALS SCIENCE↗

Effects of Intergranular Gas Bubbles on Thermal Conductivity

Model microstructures obtained from phase-field simulations are used to study the effective heat transfer across bicrys- tals with stationary grain boundary bubble populations. We find that the grain boundary coverage, irrespective of the intergranular bubble radii, is the most relevant parameter to the thermal resistance, which we use to derive effec- tive Kapitza resistances that are dependent on the grain boundary coverage and Kaptiza resistance of the intact grain boundary. We propose a model to predict thermal conductivity as a function of porosity, grain-size, Kaptiza resistance of the intact grain boundary, and grain boundary bubble coverage.

36 MATERIALS SCIENCE↗

Intelligent Weld Manufacturing: Role of Integrated Computational Welding Engineering

A master welder uses his sensory perceptions to evaluate the process and connect them with his/her knowledge base to take the necessary corrective measures with his/her acquired skills to make a good weld. All these actions must take place in real time. Success depends on intuition and skills, and the procedure is labor-intensive and frequently unreliable. The solution is intelligent weld manufacturing. The ultimate goal of intelligent weld manufacturing would involve sensing and control of heat source position, weld temperature, weld penetration, defect formation and ultimately control of microstructure and properties. This involves a solution to a problem (welding) with many highly coupled and nonlinear variables. The trend is to use an emerging tool known as intelligent control. This approach enables the user to choose a desirable end factor such as properties, defect control, or productivity to derive the selection of process parameters such as current, voltage, or speed to provide for appropriate control of the process. Important elements of intelligent manufacturing are sensing and control theory and design, process modeling, and artificial intelligence. Significant progress has been made in all these areas. Integrated computational welding engineering (ICWE) is an emerging field that will aid in the realization of intelligent weld manufacturing. The paper will discuss the progress in process modeling, microstructure, properties, and process control and automation and the importance of ICWE. Also, control and automation strategies for friction stir welding will be discussed.

42 ENGINEERING↗

The Effects of Silicon and Niobium Concentration on the Solidification Behavior and Microstructure of Cast Monel Alloys

Cast Monel alloys are used in applications requiring a combination of good mechanical properties and excellent resistance to corrosion. Despite prevalent industrial use, relatively few studies have been conducted to investigate the relationships between composition, solidification behavior, and microstructure. Given that these alloys are used in the cast and welded conditions, these factors have a significant influence over the material properties. Here, in this work, microstructural characterization, electron probe microanalysis, X-ray diffraction, and differential scanning calorimetry were used to study how changes in Si and Nb concentrations affected the solidification path and microstructure of Monel alloys. It was found that increasing Nb concentration stabilized higher amounts of MC carbides and suppressed graphite formation during solidification. It was also found that the high nominal concentration and segregation of Si to the liquid led to the formation of Ni 31 Si 12 and other silicides via terminal eutectic reactions at the end of solidification. A pseudo-binary solidification diagram was constructed using experimental data and was applied to predict the mass fraction of solidified eutectic as a function of composition. The modeled microstructures were found to be in good agreement with experimentally measured phase fractions.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of Al-Mg-Sc-Zr Alloy Variable Polarity Plasma Arc Welding Joint

Al-Mg-Sc-Zr alloy plates were welded by variable polarity plasma arc welding (VPPAW) with Sc-containing filler wire. The microstructure and mechanical properties were investigated. Results show that the weld zone and heat-affected zone (HAZ) are narrow due to the high concentrated heat input of VPPAW. Primary Al{sub 3}(Sc,Zr) particles are nice nucleating sites for α-Al, which can significantly refine the grains of α-Al, helping the weld zone maintain an outstanding strength. The unmelted Al{sub 3}(Sc,Zr) precipitates of the base metal aggregated near the fusion boundary result in the formation of a fine equiaxed grains zone, which improves the bonding degree between the weld zone and the base metal. The Al{sub 3}(Sc,Zr) precipitates in the HAZ have excellent inhibition effect on recrystallization. According to the observed microhardness distribution and microstructure characteristics, the microstructure model of welded joint is obtained. The fractured position of welded joint locates in the weld zone. The tensile strength of the welded joint without reinforcing rib is 330 MPa. The welding coefficient reaches 74%.

36 MATERIALS SCIENCE↗