Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “metallic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Molecular orbital studies in oxidation: Sulfate formation and metal-metal oxide adhesion

The chemical mechanisms for sulfate formation from sodium chloride and sulfur trioxide, which is a product of jet fuel combustion was determined. Molten sodium sulfate leads to hot corrosion of the protective oxide layers on turbine blades. How yttrium dopants in nidkel-aluminum alloys used in turbine blades reduce the spalling rate of protective alumina films and enhance their adhesion was also determined. Two other fulfate mechanisms were deduced and structure of carbon monoxide on a clean chronium and clean platinum-titanium alloys surfaces was determined. All studies were by use of the atom superposition and electron delocalization molecular orbital (ASED-MO) theory. Seven studies were completed. Their titles and abstracts are given.

Anderson, A. B.↗
NASA NTRS1988

Behavior of ceramic particles at the solid-liquid metal interface in metal matrix composites

Directional solidification results were obtained in order to investigate particle behavior at the solid-liquid interface in Al-2 pct Mg (cellular interface) and Al-6.1 pct Ni (eutectic interface) alloys. It is found that particles can be entrapped in the solid if adequate solidification rates and temperature gradients are used. Model results showed critical velocity values slightly higher than those obtained experimentally.

Stefanescu, D. M.↗
NASA NTRS1994

Theoretical study of the effect of an AlGaAs double heterostructure on metal-semiconductor-metal photodetector performance

The sizing and efficiency of an aircraft is largely determined by the performance of its high-lift system. Subsonic civil transports most often use deployable multi-element airfoils to achieve the maximum-lift requirements for landing, as well as the high lift-to-drag ratios for take-off. However, these systems produce very complex flow fields which are not fully understood by the scientific community. In order to compete in today's market place, aircraft manufacturers will have to design better high-lift systems. Therefore, a more thorough understanding of the flows associated with these systems is desired. Flight and wind-tunnel experiments have been conducted on NASA Langley's B737-100 research aircraft to obtain detailed full-scale flow measurements on a multi-element high-lift system at various flight conditions. As part of this effort, computational aerodynamic tools are being used to provide preliminary flow-field information for instrumentation development, and to provide additional insight during the data analysis and interpretation process. The purpose of this paper is to demonstrate the ability and usefulness of a three-dimensional low-order potentialflow solver, PMARC, by comparing computational results with data obtained from 1/8 scale wind-tunnel tests. Overall, correlation of experimental and computational data reveals that the panel method is able to predict reasonably well the pressures of the aircraft's multi-element wing at several spanwise stations. PMARC's versatility and usefulness is also demonstrated by accurately predicting inviscid threedimensional flow features for several intricate geometrical regions.

Salem, Ali F.↗
NASA NTRS2015

An Investigation on the Use of a Laser Ablation Treatment on Metallic Surfaces and the Influence of Temperature on Fracture Toughness of Hybrid Co-Cured Metal-PMC Interfaces

Hybrid composite laminates that contain alternating layers of titanium alloys and carbon fabric reinforced polyimide matrix composites (PMC) are excellent candidates for light-weight, high-temperature structural materials for high-speed aerospace vehicles. The delamination resistance of the hybrid titanium-PMC interface is of crucial consideration for structural integrity during service. Here, we report the first investigations on the use of laser ablation in combination with sol-gel treatment technique on Ti/NiTi foil surfaces in co-cured hybrid polyimide matrix composite laminates. Mode-I and mode-II fracture toughness of the hybrid Ti/NiTi-PMC interface as a function of temperature were determined via experimental testing and finite element analysis.

Connell, John↗
NASA NTRS2017

Functionally Graded Metal-Metal Composite Structures

Methods and devices are disclosed for creating a multiple alloy composite structure by forming a three-dimensional arrangement of a first alloy composition in which the three-dimensional arrangement has a substantially open and continuous porosity. The three-dimensional arrangement of the first alloy composition is infused with at least a second alloy composition, where the second alloy composition comprises a shape memory alloy. The three-dimensional arrangement is consolidated into a fully dense solid structure, and the original shape of the second alloy composition is set for reversible transformation. Strain is applied to the fully dense solid structure, which is treated with heat so that the shape memory alloy composition becomes memory activated to recover the original shape. An interwoven composite of the first alloy composition and the memory-activated second alloy composition is thereby formed in the multiple alloy composite structure.

Brice, Craig A.↗
NASA NTRS1998

An Assessment of Molten Metal Detachment Hazards During Electron Beam Welding in Space

The safety issue has been raised with regards to potential molten metal detachments from the weld pool and cold filler wire during electron beam welding in space. This investigation was undertaken to evaluate if molten metal could detach and come in contact with astronauts and burn through the fabric of the astronauts' Extravehicular Mobility Unit (EMU) during electron beam welding in space. Molten metal detachments from either the weld/cut substrate or weld wire could present harm to a astronaut if the detachment was to burn through the fabric of the EMU. Theoretical models were developed to predict the possibility and size of the molten metal detachment hazards during the electron beam welding exercises at Low Earth Orbit (LEO). The primary molten metal detachment concerns were those cases of molten metal separation from the metal surface due to metal cutting, weld pool splashing, entrainment and release of molten metal due to filler wire snap-out from the weld puddle, and molten metal accumulation and release from the end of the weld wire. Some possible ways of obtaining molten metal drop detachments would include an impulse force, or bump, to the weld sample, cut surface, or filler wire. Theoretical models were developed for these detachment concerns from principles of impact and kinetic energies, surface tension, drop geometry, surface energies, and particle dynamics. The surface tension represents the force opposing the liquid metal drop from detaching whereas the weight of the liquid metal droplet represents a force that is tending to detach the molten metal drop. Theoretical calculations have indicated that only a small amount of energy is required to detach a liquid metal drop; however, much of the energy of an impact is absorbed in the sample or weld plate before it reaches the metal drop on the cut edge or surface. The tendency for detachment is directly proportional to the weld pool radius and metal density and inversely proportional to the surface tension of the liquid metal. For a detachment the initial kinetic energy of the weld pool with respect to the plate has to exceed the energy to form the extra surface required for the detachment of the pool. The difficulty is in transferring the energy from the point of impact through the plate and sample to the cut edge. It is likely that not all of the kinetic energy is available for detaching the pool; some may be sequestered in weld pool oscillations. The coefficient of restitution for the collision will be lower than one if irreversible deformation, for example plastic flow deformation, takes place during the collision. Thus determining the amount of energy from an impact that actually reaches the molten metal droplet is critical. Various molten metal detachment scenarios were tested experimentally in an enclosed vacuum chamber using the Ukrainian Universal Hand Tool, an electron beam welder designed for space welding. The experimental testing was performed in a 4 ft. X 4 ft. vacuum chamber at Marshall Space Flight Center, evacuated to vacuum levels of at least 50 microTorr, and also some welding garment material was utilized to observe the effect of the molten metal detachments on the material. A "carillon" apparatus consisting of four pendulum hammer strikers, each weighing approximately 3.65 lbs, raised to predetermined specific heights was used to apply an impact force to the weld sample/plate during electron beam welding and cutting exercises. The strikers were released by switching on an electric motor to rotate a pin holding wires retaining the strikers at desired heights. The specimens were suspended so as to be free to respond to the blows with a sudden velocity increment. The specimens were mounted on a hinged plate for minimizing effective mass with the option to fasten it down so as to raise its effective mass closer to that anticipated for an actual space welding scenario. Measurements were made of the impact energy and the horizontal fling distances of the detached metal drops. It was not particularly easy to generate the detachments for this experiment. This document presents the details of the theoretical modeling effort and a summary of the experimental effort to measure molten metal drop detachments from terrestrial electron beam welding in the enclosed vacuum chamber. The results of the experimental effort have shown that molten metal detachments can occur from the sample/weld plate only if a sufficiently large impact force is applied to the weld plate. A "weld pool detachment parameter" was determined to indicate whether detachment would occur. Detachment can be either full or partial (dripping), Partial detachment means that the weld pool detached from one side of the liquid-solid boundary so as to leave a hole at the puddle site but remained attached over part of the liquid-solid boundary and dripped down the plate with no fully detached material detected. Full detachment, however, does not necessarily mean that the whole pool fully detached; in some cases only a smaller portion of the pool detached, the remainder dripping down the plate. The weld pool detachment parameter according to theory and according to the empirical data allows a determination of whether full detachments might occur. Theoretical calculations indicated titanium alloy would be the most difficult from which to detach molten metal droplets followed by stainless steel and then by aluminum. The experimental results were for the most part consistent with the theoretical analysis and predictions. The above theory is applicable to other situations as desired for assessing the potential for molten metal detachments.

Fragomeni, James M.↗
NASA NTRSDate not supplied

Tin-Essako 001: A Metal-Rich Ureilite?

Introduction: Metal-rich achondrites include a variety of types, and likely have a variety of origins. Models range from gravitational mixing at the core-mantle boundaries of differentatiated asteroids, to complex impact mixing scenarios. We describe a new type of metal-rich achondrite that might be the first metal-rich ureilite. Sample: Tin-Essako (TE) 001 (~4.3 g) was found in Mali in 2020 and purchased by Jay Piatek in 2021. It was classified as a metal-rich ungrouped achondrite, with olivine and oxygen isotope (d18O=8.2810‰, d17O=3.718‰, avg. 3) compositions suggesting affinity to ureilites [1]. We studied one polished section (~187.7 mm2) of TE 001. Petrography: TE 001 consists of ~60% metal and 40% silicates, heterogeneously distributed. The metal is largely fresh, but iron oxides (presumably terrestrial) occur along one edge and in some patches and veins in the interior. The silicates are dominantly olivine (≥90%), with melt-textured areas of plagioclase + Si-rich glass. Minor phases include chromite and carbon. Olivine occurs as rounded grains (up to ~2.5 mm) in metal, commonly with rims of melt-textured plagioclase + glass. Olivine also occurs in more massive areas having a “honeycomb” texture, with rounded olivine “cells” surrounded by an interstitial network of reduced olivine riddled with tiny metal grains, plus melt-textured plagioclase + Si-rich glass. Chromite occurs as subhedral to rounded grains; smaller grains (30-250 mm) are included in olivine and a few larger grains (400-500 mm) are isolated within metal. A carbon phase occurs as lacy-textured rims around olivine grains in metal, or small patches within metal. Mineral Compositions: The olivine (excluding interstitial areas) is Fo 73.9±0.5, with 0.25±0.02 wt.% CaO, 0.31±0.01 wt% Cr2O3, 0.01 wt.% NiO, and molar Fe/Mn=49.8±2.2 (53 analyses). Olivine in interstitial areas has Fo up to at least 91. Smaller chromite grains have Fe# (molar Fe/[Fe+Mg]) = 0.54±0.01, Cr# (molar Cr/[Cr+Al]) = 0.52±0.01, 0.52±0.02 wt.% V2O3 and 0.21±0.04 wt% ZnO (28 analyses). One larger grain is zoned from Fe# = 0.45, Cr# =0.52 to Fe# = 0.40, Cr# =0.57, and contains thin Al-rich lamellae not resolved by EMPA. One irregularly shaped patch of chromite included in olivine has Fe# =0.26 and contains no ZnO. Plagioclase laths are An ~53-60, with ≤0.01 wt.% K2O. Glass contains 75-76 wt% SiO2 and ~16 wt% Al2O3. The metal contains 5.2±0.2 wt% Ni, 0.46±0.02 wt.% Co, and 0.01±0.01 wt.% Cr, with Si and P below detection (168 analyses). Discussion: The olivine + chromite assemblage in TE 001 is similar to the most ferroan ureilites (Fo ~75-79 [2]), as are the oxygen isotopes [1]. The presence of a carbon phase supports this, although the identity of this phase (graphite as in ureilites?) remains to be determined. The “honeycomb” textured areas, in particular, the presence of olivine “reduction rims,” resemble shock-smelted olivine areas in ureilites [3], but interstitial melt-textured plagioclase laths + glass like those in TE 001 have not been reported in such (or any) ureilites. Olivine in TE 001 is marginally more ferroan than in the most FeO-rich ureilite, with Fe-Mg-Mn composition offset from the trend of olivine + low-Ca pyroxene ureilites similar to augite-bearing ureilites [4]. CaO and Cr2O3 contents are in the range of those in ureilite olivine [ ] , though Cr2O3 is at the extreme low end of the range [5]. Chromites (except the unusual one) have similar Fe# to the most ferroan primary chromites in ureilites [2], but distinctly lower Cr# (0.52 vs. 0.71). Metal compositions are with the range for metal in ureilites [7]. The absence of pyroxene and sulfide, and the high abundance of metal in TE 001, are unlike ureilites. One possibility is that a ferroan, chromite-bearing, pyroxene-poor ureilite was invaded (possibly due to impact) by a metallic liquid (low S content suggests very high temperature), resulting in complete melting of pyroxene and smelting of olivine, with rapid recrystallization of melted silicate as plagioclase + glass. Alternatively, a pre-existing metal-rich ureilite assemblage may have been impact melted. Additional types of data will be obtained to evaluate these hypotheses (i.e., is the metal indigenous?) and assess affinity to ureilites.

olivine↗
NASA NTRS1995

Adhesion, friction, and wear behavior of clean metal-ceramic couples

When a clean metal is brought into contact with a clean, harder ceramic in ultrahigh vacuum, strong bonds form between the two materials. The interfacial bond strength between the metal and ceramic surfaces in sliding contact is generally greater than the cohesive bond strength in the metal. Thus, fracture of the cohesive bonds in the metal results when shearing occurs. These strong interfacial bonds and the shearing fracture in the metal are the main causes of the observed wear behavior and the transfer of the metal to the ceramic. In the literature, the surface energy (bond energy) per unit area of the metal is shown to be related to the degree of interfacial bond strength per unit area. Because the two materials of a metal-ceramic couple have markedly different ductilities, contact can cause considerable plastic deformation of the softer metal. It is the ductility of the metal, then, that determines the real area of contact. In general, the less ductile the metal, the smaller the real area of contact. The coefficient of friction for clean surfaces of metal-ceramic couples correlates with the metals total surface energy in the real area of contact gamma A (which is the product of the surface energy per unit area of the metal gamma and the real area of contact (A)). The coefficient of friction increases as gamma A increases. Furthermore, gamma A is associated with the wear and transfer of the metal at the metal-ceramic interface: the higher the value of gamma A, the greater the wear and transfer of the metal.

Miyoshi, Kazuhisa↗
NASA NTRS1995

Internal and surface phenomena in metal combustion

Combustion of metals has been widely studied in the past, primarily because of their high oxidation enthalpies. A general understanding of metal combustion has been developed based on the recognition of the existence of both vapor-phase and surface reactions and involvement of the reaction products in the ensuing heterogeneous combustion. However, distinct features often observed in metal particle combustion, such as brightness oscillations and jumps (spearpoints), disruptive burning, and non-symmetric flames are not currently understood. Recent metal combustion experiments using uniform high-temperature metal droplets produced by a novel micro-arc technique have indicated that oxygen dissolves in the interior of burning particles of certain metals and that the subsequent transformations of the metal-oxygen solutions into stoichiometric oxides are accompanied with sufficient heat release to cause observed brightness and temperature jumps. Similar oxygen dissolution has been observed in recent experiments on bulk iron combustion but has not been associated with such dramatic effects. This research addresses heterogeneous metal droplet combustion, specifically focusing on oxygen penetration into the burning metal droplets, and its influence on the metal combustion rate, temperature history, and disruptive burning. A unique feature of the experimental approach is the combination of the microgravity environment with a novel micro-arc Generator of Monodispersed Metal Droplets (GEMMED), ensuring repeatable formation and ignition of uniform metal droplets with controllable initial temperature and velocity. The droplet initial temperatures can be adjusted within a wide range from just above the metal melting point, which provides means to ignite droplets instantly upon entering an oxygen containing environment. Initial droplet velocity will be set equal to zero allowing one to organize metal combustion microgravity experiments in a fashion similar to usual microgravity liquid fuel droplet combustion studies. In addition, the internal compositions of rapidly quenched metal particles will be analyzed using SEM technique. Such compositions are similar to those existing during the combustion and provide new insight on metal combustion processes. The results of this experimental work will be used to model the fundamental mechanisms of metal combustion. Preliminary experimental results on Al and Zr particle combustion at normal gravity are discussed here.

Dreizin, Edward L.↗