Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “laser operations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Surface-Emitting Distributed Feedback Terahertz Quantum-Cascade Lasers in Metal-Metal Waveguides

Single-mode surface-emitting distributed feedback terahertz quantumcascade lasers operating around 2.9 THz are developed in metal-metal waveguides. A combination of techniques including precise control of phase of reflection at the facets, and u e of metal on the sidewalls to eliminate higher-order lateral modes allow robust single-mode operation over a range of approximately 0.35 THz. Single-lobed far-field radiation pattern is obtained using a pi phase-shift in center of the second-order Bragg grating. A grating device operating at 2.93 THz lased up to 149 K in pulsed mode and a temperature tuning of 19 .7 GHz was observed from 5 K to 147 K. The same device lased up to 78 K in continuous-wave (cw) mode emitting more than 6 m W of cw power at 5 K. ln general, maximum temperature of pulsed operation for grating devices was within a few Kelvin of that of multi-mode Fabry-Perot ridge lasers

Kumar, Sushil↗

Cloud top remote sensing by airborne lidar

Observations of cloud top height, backscattering, and signal depolarization have been obtained by a lidar system operating onboard a high-altitude research aircraft. The transmitter for the cloud lidar system is a doubled Nd:YAG laser operating at 5 Hz. The system functions as a fully automated sensor under microprocessor control and operates from a nominal 19-km altitude. Measurements have been acquired over a wide variety of cloud cover in conjunction with passive visible and infrared measurements. Initial observation results are reported

Spinhirne, J. D.↗

Laser action in chromium-doped forsterite

This paper reports on pulsed laser operation obtained in chromium-activated forsterite Cr(3+):Mg2SiO4 at room temperature. The spectrum of the free-running laser peaks at 1235 nm and a bandwidth of about 22 nm. The spectral range of the laser emission is expected to extend from 850 to 1300, provided the parasitic impurity absorption may be minimized by improved crystal growth techique.

Petricevic, V.↗

Q-Switch For Self-Injection Locking Of Laser

Proposed scheme for improved electro-optical switching (Q switching) of pulsed, self-injection-locked laser involves sensing of and compensation for level of pumping light. Decreases spectral width of laser pulse and makes it independent of pumping level. Laser operated in high-loss condition during initial evolution of pulse. During this time, light makes many round trips through laser resonator. Once small laser pulse evolves in high-loss condition in laser resonator, optical configuration of resonator switched to one of low loss. In low-loss state, majority of energy extracted in efficient manner while retaining narrow spectral width of initial pulse. Beneficial in reducing jitter.

Barnes, Norman P.↗

Near-IR diode laser absorption for measurement of tropospheric HO2

The possibility of using tunable lead salt diode lasers in the infrared for measurement of tropospheric HO2 has been frequently considered. Although the sensitivity of diode laser absorption has been improved through the use of high frequency detection techniques, nature has been unkind in that the HO2 absorption cross sections are weak. Even using the most optimistic assumptions about attainable path length and detectable absorbance, measurement of tropospheric HO2 by diode laser absorption in the mid-IR appears marginal. A possible alternative method for measuring HO2 is by absorption at near-infrared wavelengths. Several absorption bands of HO2 occur in the wavelength region between 1.2 and 1.6 micron due to electronic transitions and overtones of the fundamental vibrational modes. InGaAsP diode lasers operate in this wavelength region and can be used for high resolution spectroscopy in a manner analogous to the lead salt lasers. A diode laser system in the near-IR offers some advantages.

Stanton, Alan C.↗

Characterization of Artificial Guidestars Generated in the Mesospheric Sodium Layer

Using a 10 W average power sum-frequency laser, we have generated resonant fluorescence beacons in the mesospheric sodium layer and are currently evaluating them for use as an artificial guidestar for atmospheric compensation using adaptive optics. Two flashlamp pumped Nd:YAG lasers operating at 1.064 and 1.319 microns are mixed in a lithium triborate crystal to produce 589 nm light at 840 Hz. The laser emits 47.5 microsec mode-locked pulse trains at 11-14 mJ per pulse and is tuned to the sodium resonance transition with intracavity etalons.

Jelonek, M. P.↗

Liquid-phase epitaxy grown PbSnTe distributed feedback laser diodes with broad continuous single-mode tuning range

Distributed feedback (DFB) pulsed laser operation has been demonstrated in stripe geometry Pb(1-x)Sn(x)Te double-heterostructures grown by liquid-phase epitaxy. The grating structure of 0.79 micron periodicity operates in first order near 12.8 microns and was fabricated prior to the liquid-phase epitaxial growth using holographic exposure techniques. These DFB lasers had moderate thresholds, 3.6 kA/sq cm, and the output power versus current curves exhibited a sharp turn-on free of kinks. Clean, single-mode emission spectra, continuously tunable over a range in excess of 20 per cm, centered about 780 per cm (12.8 microns), and at an average rate of 1.2 per cm-K from 9 to 26 K, were observed. While weaker modes could at times be seen in the spectrum, substantially single-mode operation was obtained over the entire operating range and to over 10 times threshold.

Hsieh, H.-H.↗

Diode-pumped Ho:Tm:YLF laser pumping and AgGaSe2 parametric oscillator

Tuning of both the pump laser, a Ho:Tm:YLF laser operating on the 5 I 7 - 5 I 8 transition, and an AgGaSe2 parametric oscillator has been demonstrated. Tuning of the Ho:Tm:YLF laser is complicated but not frustrated by the existence of both CO2 and H2O lines in the vicinity of the laser transition. Tuning of the parametric oscillator was achieved by tuning of the pump laser. Injection seeding of the parametric oscillator on the nonresonant signal was also demonstrated. In addition, the measured efficiencies of the parametric oscillator were compared by two different methods, measuring the parametric-oscillator output energy and measuring the energy depleted from the pump. By comparison of these measurements, the intrinsic efficiency of the parametric oscillator cab be determined

Barnes, Norman P.↗

Spatial Combining of Laser-Diode Beams for Pumping an NPRO

A free-space optical beam combiner now undergoing development makes it possible to use the outputs of multiple multimode laser diodes to pump a neodymium-doped yttrium aluminum garnet (Nd:YAG) non-planar ring oscillator (NPRO) laser while ensuring that the laser operates at only a single desired frequency. Heretofore, a Nd:YAG NPRO like the present one has been pumped by a single multimode laser-diode beam delivered via an optical fiber. It would be desirable to use multiple pump laser diodes to increase reliability beyond that obtainable from a single pump laser diode. However, as explained in this article, simplistically coupling multiple multimode laser-diode beams through a fiber-optic combiner would entail a significant reduction in coupling efficiency, and lasing would occur at one or more other frequencies in addition to the single desired frequency. To minimize coupling loss, one must ensure that the NA (approximately equal to 0.3) of the combined laser-diode beams is less than the NA of the fiber. The A(Omega) of the laser-diode beam in the slow-axis plane is 1/1.3 as large as that of the fiber. This A(Omega) is small enough to enable efficient coupling of light into the optical fiber, but too large for combining of beams in the slow-axis plane. Therefore, a pair of cylindrical lenses is used to cancel the slow-axis plane magnification introduced by the on-cylindrical lenses used to effect magnification in the fast-axis plane.

Gelsinger, Paul↗

Doppler Lidar Measurements of Tropospheric Wind Profiles Using the Aerosol Double Edge Technique

The development of a ground based direct detection Doppler lidar based on the recently described aerosol double edge technique is reported. A pulsed, injection seeded Nd:YAG laser operating at 1064 nm is used to make range resolved measurements of atmospheric winds in the free troposphere. The wind measurements are determined by measuring the Doppler shift of the laser signal backscattered from atmospheric aerosols. The lidar instrument and double edge method are described and initial tropospheric wind profile measurements are presented. Wind profiles are reported for both day and night operation. The measurements extend to altitudes as high as 14 km and are compared to rawinsonde wind profile data from Dulles airport in Virginia. Vertical resolution of the lidar measurements is 330 m and the rms precision of the measurements is a low as 0.6 m/s.

Gentry, Bruce M.↗

Quasinormal Coupled-Mode Analysis of Dynamic Gain in Exceptional-Point Lasers

One of the key features of lasers operating near exceptional points (EPs) is that the gain medium can support an oscillating population inversion above a pump threshold, leading to self-modulated laser dynamics. This unusual behavior opens up new possibilities for frequency comb generation and temporal modulation. However, the dynamic population inversion couples signals with different frequencies and is difficult to capture using conventional temporal coupled-mode theory (TCMT) based on stationary saturable gain. In this paper, we develop a perturbative coupled-mode analysis framework to capture the spatial-temporal dynamics of near-EP lasers. By decomposing discrete frequency generation into multiple excitations of resonant modes, our analysis establishes a minimal physical model that translates the local distribution of dynamic population-inversion into a resonant modal interpretation of laser gain. Furthermore, this work enables the exploration of unique properties in this self-time-modulated systems, such as time-varying scattering and nonreciprocal transmission.

Absorption↗

Generation of Bright Soft X-ray Laser Beams (Final Report)

The project goal was to demonstrate new compact soft x-ray lasers emitting high energy ultrashort pulses at shorter wavelengths and increased repetition rates by amplification in atomic transitions in high density laser-created plasmas. To demonstrate these lasers we developed new high power solid state lasers. The project succeeded in demonstrating the shortest wavelength compact soft x-ray laser to date, 6.85 nm wavelength, and the highest repetition rate table-top soft x-ray laser, 400 Hz. We also applied these compact soft x-ray laser sources to determine the composition of materials with nanoscale resolution using a new technique that combines soft x-ray laser ablation with mass spectrometry, and we demonstrated that these lasers are capable of acquiring nanoscale resolution holograms with picosecond time resolution. The combination of an increased pumping efficiency with increased repetition rates can yield soft x-ray laser beams with an unprecedented average power on a table-top for applications demanding a high photon flux. We have demonstrated that the efficiency of plasma-based laser-pumped soft x-ray lasers can be significantly increased by detailed pulse shaping of the pump laser using a new pulse synthesizer. Results include the demonstration of 18.9 nm wavelength laser operation at a record 400 Hz repetition rate, and the extension of repetitive gain-saturated plasma-based table-top x-ray lasers to the shortest wavelength to date, 6.85 nm. Laser amplification was also observed at wavelengths as short at 5.8 nm by isolectronic scaling in Ni-like lanthanide ions. We have also conducted simulations to explore the possibility of demonstrating gain saturated atomic x-ray lasers near the carbon K-edge, in the “carbon window” for the first time. The work conducted under this program also includes the use of compact soft x-ray lasers in applications to problems of chemical interest, such as isotopic composition mapping of micron-size uranium particles with nanoscale resolution, and nanoscale resolution depth profiling analysis of CoNCN-coated electrodes for water oxidation catalysis. We also demonstrated single-shot high resolution soft x-ray Fourier transform holography over a broad 7 µm diameter field of view with ~ 5 ps temporal resolution.

74 ATOMIC AND MOLECULAR PHYSICS↗

Spaceborne earth applications ranging system /SPEAR/

A technique is discussed for the accurate (i.e., to within fractions of centimeters per year) detection of earth surface motions utilizing the latest space technology. It is shown that, over a six-day period and assuming a 50% cloud cover (i.e., as experienced over the past few years of laser operation), by using spaceborne precision ranging systems, intersite distances on the order of 5 to 15 km (dependent mostly on the beam width of the laser) can be determined in the vertical and horizontal components, with errors in the 0.5- to 1.5-cm range. These errors are almost independent of ground survey errors up to 0.25 m and orbit errors up to 200 m. A spaceborne laser ranging system is assumed to range to two or more ground-emplaced retroreflectors. This can be done either in a simultaneous or nonsimultaneous mode. Hardware is under development for the latter technique.

Vonbun, F. O.↗

TELEC laser experiment

An experimental thermoelectronic laser energy converter (TELEC) was constructed and tested with a 40 kW combustion laser operating at a wave length of 10.6 microns. The objective of the test was to demonstrate the feasibility of the TELEC concept for converting a laser beam into electric power. The TELEC System is intended as the receiver for a laser power transmission system in space.

Britt, E. J.↗

Stable 1.25-W CW Methanol Laser

Far-infrared (FIR) laser operating at 119-micrometer-wavelength transition of methanol achieves very low drift in frequency. Continuous-wave (CW) FIR output is 1.25 W when laser pumped by 125-W commercial CO2 laser. Rate of drift of output frequency less than plus or minus 100 kHz per hour because laser designed to have low thermal-expansion coefficients and because temperatures of input and output couplers held within 0.1 degree C of fixed values.

Farhoomand, Jam↗

Pulsed laser spectral measurement using a Fabry-Perot interferometer: Limits to resolution

We are developing a Doppler lidar system using the edge technique to measure atmospheric wind profiles. The edge technique requires a laser with a narrow spectral bandwidth and a high resolution optical filter. The lidar system will use a Nd:YAG laser operating at 1.064 microns and a high resolution Fabry-Perot interferometer for the edge filter. The Doppler shift measurement is made by locating the laser on the edge of the filter's spectral response function. Due to the steep slope on the edge, large changes in the filter transmission will be observed for small changes in frequency. The Doppler shift can be determined from a measurement of this change in filter transmission if the filter spectral response function in the region of the measurement is well known. Recently developed injection seeded solid state lasers have made near transform limited laser output readily available for lidar work. Injection-seeded Nd:YAG laser exhibit single mode output with smooth Gaussian temporal pulse shapes. Results of an experiment we conducted to evaluate the effects of a short Gaussian temporal input pulse on the spectral response of a high resolution Fabry-Perot interferometer are presented.

Notari, Anthony↗

LaRC-developed catalysts for CO2 lasers

Pulsed CO2 lasers have many remote sensing applications from space, airborne, and ground platforms. The NASA Laser Atmospheric Wind Sounder (LAWS) system will be designed to measure wind velocities from polar earth orbit for a period of up to three years. Accordingly, this and other applications require a closed-cycle pulsed CO2 laser which necessitates the use of an efficient CO-O2 recombination catalyst for these dissociation products which otherwise would degrade the laser operation. The required catalyst must not only operate at low temperatures but also must operate efficiently for long time periods. The research effort at NASA LaRC has centered around development and testing of CO oxidation catalysts for closed-cycle, pulsed, common and rare-isotope CO2 lasers. Researchers examined available commercial catalysts both in a laser and under simulated closed-cycle laser conditions with efforts aimed toward a thorough understanding of the fundamental catalytic reaction. These data were used to design and synthesize new catalyst compositions to better meet the catalyst requirements for closed-cycle pulsed CO2 lasers. Syntheses and test results for catalysts developed at Langley Research Center which have significantly better long-term decay characteristics than previously available catalysts and at the same time operate quite well under lower temperature conditions are discussed.

Upchurch, Billy T.↗

Spectroscopic and lasing properties of Ho:Tm:LuAG

Ho:Tm:LuAG has been grown, examined spectroscopically, and lased at 2.1 microns. Ho:Tm:LuAG was selected for this experimental investigation when quantum-mechanical modeling predicted that it would be a good laser material for Ho laser operation on one of the 5I7 to 5I8 transitions. Lasing was achieved at 2.100 microns, one of the three wavelengths predicted to be most probable for laser action.

Barnes, Norman P.↗