Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “joint inversion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

An Archival Chandra and XMM-Newton Survey of Type 2 Quasars

In order to investigate obscuration in high-luminosity type 2 active galactic nuclei (AGNs), we analyzed Chandra and XMM-Newton archival observations for 71 type 2 quasars detected at 0.05 < z < 0.73, which were selected based on their [O III] lambda5007 emission lines. For 54 objects with good spectral fits, the observed hard X-ray luminosity ranges from 2 × 10(exp 41) to 5.3 × 10(exp 44) erg s(exp −1), with a median of 1.1 × 10(exp 43) erg s(exp −1). We find that the means of the column density and photon index of our sample are log N(sub H) = 22.9 cm(exp −2) and gamma = 1.87, respectively. From simulations using a more physically realistic model, we find that the absorbing column density estimates based on simple power-law models significantly underestimate the actual absorption in approximately half of the sources. Eleven sources show a prominent Fe K alpha emission line (EW>100 eV in the rest frame) and we detect this line in the other sources through a joint fit (spectral stacking). The correlation between the Fe K alpha and [O III] fluxes and the inverse correlation of the equivalent width of the Fe Kα line with the ratio of hard X-ray and [O III] fluxes is consistent with previous results for lower luminosity Seyfert 2 galaxies. We conclude that obscuration is the cause of the weak hard X-ray emission rather than intrinsically low X-ray luminosities. We find that about half of the population of optically selected type 2 quasars are likely to be Compton thick. We also find no evidence that the amount of X-ray obscuration depends on the AGN luminosity (over a range of more than three orders of magnitude in luminosity).

quasars: general↗
NASA NTRSDate not supplied

Adjusting a Full Body Model to Mitigate Inverse Kinematics Artifacts in Opensim

BACKGROUND: In support of Vibration Isolation and Stabilization (VIS) system development for Human Health Countermeasures (HHC) exercise systems in space, such as the European Enhanced Exploration Exercise Device (E4D) [1], dynamic quantities required to model the response of a proposed VIS while considering the effect of VIS motion on the forces between the human and VIS platform were obtained using motion capture data [2]. On occasion, large-amplitude oscillatory spikes were found in the subject’s linear and angular momentum derivatives, affecting analyses that depend on forces and moments derived from motion capture. The purpose of this investigation was to identify causes of these artifacts and techniques for their resolution. METHODS AND RESULTS: To obtain the required human dynamic quantities to drive the VIS simulation, motion capture data was collected containing recorded trajectories of passive retroreflective markers on body landmarks of an exercising subject. Since the full body Rajagopal model [3] was originally used to enhance gait analysis, upper body joints did not require large Ranges of Motion (ROM). We thus modified the Rajagopal model [4, 5] to allow it to be used for upper body intensive exercises like those common to the E4D. OpenSim Inverse Kinematics (IK) [6] was performed using these scaled subject models to generate the joint angles throughout the exercise while minimizing marker error. At times, the arms were observed to ‘snap’ from one configuration to another, causing spike artifacts. Following IK, a custom OpenSim plugin [7] was used to determine the required dynamic quantities including the rates of change of the linear and angular momenta of the human. Since motion capture is recorded at a larger time step than required by the VIS simulation, the human center of mass location was fit with splines and a second derivative taken to obtain the momentum derivative, allowing the VIS simulation to maintain conservation of momentum when appropriate. In a few cases during this stage, artifacts much larger than the expected noise of the second derivatives were introduced. Investigation of cases containing artifacts revealed several modifications that could be made to the OpenSim model to improve IK results. Since OpenSim models use Euler angles and rotation sequences, ‘gimbal lock’ would be encountered in the arms when raised 90 degrees to the side (e.g., T-pose, some hang clean exercise, etc.). This was resolved by reorienting the horizontal axes at the shoulder joint by 45 degrees, placing ‘gimbal lock’ outside common arm ROM, with the arm ROMs adjusted following this change. Elbow and wrist ROMs could also be adjusted to allow realistic motion while at the same time limiting the likelihood of unrealistic orientations. On occasion, the arms flipped backwards when raised above the head. This was prevented by using medial elbow markers in scaling and IK. When medial markers were not available, the acromial joint location in the unscaled model was shifted before model scaling to better align the arm with available markers. Lastly, artifacts which became apparent after taking the second derivatives of spline-fit data were found to occur in cases when the pelvis rotation limit prevented the full range of motion of an exercise. These issues were resolved by unclamping the pelvis rotation limit. Through this investigation, an understanding of conditions leading to IK artifacts was acquired allowing the automation of artifact detection. These artifact detection and mitigation techniques can be applied toward modeling of upper body motions in aerospace and other fields for improved IK results.

C A Bell↗
NASA NTRS1986

Kalman filtering, smoothing and recursive robot arm forward and inverse dynamics

The inverse and forward dynamics problems for multi-link serial manipulators are solved by using recursive techniques from linear filtering and smoothing theory. The pivotal step is to cast the system dynamics and kinematics as a two-point boundary-value problem. Solution of this problem leads to filtering and smoothing techniques identical to the equations of Kalman filtering and Bryson-Frazier fixed time-interval smoothing. The solutions prescribe an inward filtering recursion to compute a sequence of constraint moments and forces followed by an outward recursion to determine a corresponding sequence of angular and linear accelerations. In addition to providing techniques to compute joint accelerations from applied joint moments (and vice versa), the report provides an approach to evaluate recursively the composite multi-link system inertia matrix and its inverse. The report lays the foundation for the potential use of filtering and smoothing techniques in robot inverse and forward dynamics and in robot control design.

Rodriguez, G.↗
NASA NTRS1989

Simplified Linear Multivariable Control Of Robots

Simplified method developed to design control system that makes joints of robot follow reference trajectories. Generic design includes independent multivariable feedforward and feedback controllers. Feedforward controller based on inverse of linearized model of dynamics of robot and implements control law that contains only proportional and first and second derivatives of reference trajectories with respect to time. Feedback controller, which implements control law of proportional, first-derivative, and integral terms, makes tracking errors converge toward zero as time passes.

Seraji, Homayoun↗
NASA NTRS1990

Recursive dynamics for geared robot manipulators

The authors consider the dynamical modeling of robot manipulators whose joint actuators consist of motors driving the joints through gears. The dynamical models for such manipulators are significantly more complex than those for direct drive manipulators. The authors develop recursive O(n) inverse and forward dynamics algorithms as well as recursive O(n2) algorithms for the computation of the mass matrix for geared manipulators. It is shown that, despite the added complexity of the dynamical models for geared manipulators, the algorithms closely resemble the corresponding algorithms for direct drive manipulators, and that the additional algorithmic or computational complexity is relatively insignificant. As a consequence, with little additional cost, existing direct drive algorithms can be easily extended to handle the effects of gearing at the joints.

Jain, A.↗
NASA NTRS1989

Characterization and control of self-motions in redundant manipulators

The presence of redundant degrees of freedom in a manipulator structure leads to a physical phenomenon known as a self-motion, which is a continuous motion of the manipulator joints that leaves the end-effector motionless. In the first part of the paper, a global manifold mapping reformulation of manipulator kinematics is reviewed, and the inverse kinematic solution for redundant manipulators is developed in terms of self-motion manifolds. Global characterizations of the self-motion manifolds in terms of their number, geometry, homotopy class, and null space are reviewed using examples. Much previous work in redundant manipulator control has been concerned with the redundancy resolution problem, in which methods are developed to determine, or resolve, the motion of the joints in order to achieve end-effector trajectory control while optimizing additional objective functions. Redundancy resolution problems can be equivalently posed as the control of self-motions. Alternatives for redundancy resolution are briefly discussed.

Burdick, J.↗
NASA NTRS1994

Robust stability of second-order systems

Nonlinear control using feedback linearization or inverse dynamics for robotic manipulators yields good results in the absence of modeling uncertainty. However, modeling uncertainties due to unknown joint friction coefficients and payload variations can give rise to undesirable characteristics when these control systems are implemented. It is shown how passivity concepts can be used to supplement the feedback linearization control design technique, in order to make it robust with respect to the uncertain effects mentioned above. Results are obtained for space manipulators with freely floating base; however, they are applicable to fixed base manipulators as well. The controller guarantees asymptotic tracking of the joint variables. Closed-loop simulation results are illustrated for planar space manipulators for cases where uncertainty exists in friction modeling and payload inertial parameters.

Chuang, C.-H.↗
NASA NTRS1989

An order (n) algorithm for the dynamics simulation of robotic systems

The formulation of an Order (n) algorithm for DISCOS (Dynamics Interaction Simulation of Controls and Structures), which is an industry-standard software package for simulation and analysis of flexible multibody systems is presented. For systems involving many bodies, the new Order (n) version of DISCOS is much faster than the current version. Results of the experimental validation of the dynamics software are also presented. The experiment is carried out on a seven-joint robot arm at NASA's Goddard Space Flight Center. The algorithm used in the current version of DISCOS requires the inverse of a matrix whose dimension is equal to the number of constraints in the system. Generally, the number of constraints in a system is roughly proportional to the number of bodies in the system, and matrix inversion requires O(p exp 3) operations, where p is the dimension of the matrix. The current version of DISCOS is therefore considered an Order (n exp 3) algorithm. In contrast, the Order (n) algorithm requires inversion of matrices which are small, and the number of matrices to be inverted increases only linearly with the number of bodies. The newly-developed Order (n) DISCOS is currently capable of handling chain and tree topologies as well as multiple closed loops. Continuing development will extend the capability of the software to deal with typical robotics applications such as put-and-place, multi-arm hand-off and surface sliding.

Chun, H. M.↗
NASA NTRS1986

Linear multivariable control of robot manipulators

The paper presents a simple scheme for the linear multivariable control of multi-link robot manipulators. The control scheme consists of multivariable feedforward and feedback controllers. The feedforward controller is the minimal inverse of the linearized model of robot dynamics and contains only proportional-double-derivative terms. This controller ensures that the manipulator joint angles track any reference trajectories. The feedback controller is of proportional-derivative type and achieves stability and pole placement. This controller reduces any initial tracking error to zero as desired. The two controllers are independent of each other and are designed separately based on the linearized robot model and then integrated in an overall control scheme.

Seraji, H.↗
NASA NTRS1990

Local sensory control of a dexterous end effector

A numerical scheme was developed to solve the inverse kinematics for a user-defined manipulator. The scheme was based on a nonlinear least-squares technique which determines the joint variables by minimizing the difference between the target end effector pose and the actual end effector pose. The scheme was adapted to a dexterous hand in which the joints are either prismatic or revolute and the fingers are considered open kinematic chains. Feasible solutions were obtained using a three-fingered dexterous hand. An algorithm to estimate the position and orientation of a pre-grasped object was also developed. The algorithm was based on triangulation using an ideal sensor and a spherical object model. By choosing the object to be a sphere, only the position of the object frame was important. Based on these simplifications, a minimum of three sensors are needed to find the position of a sphere. A two dimensional example to determine the position of a circle coordinate frame using a two-fingered dexterous hand was presented.

Pinto, Victor H.↗
NASA NTRSDate not supplied

Accuracy of Center of Pressure Determination via Motion Capture

BACKGROUND: This study was conducted to support the stability assessment for tasks in lunar gravity and exercises on a Vibration Isolation and Stabilization (VIS) system in microgravity based on the dynamic feasibility criterion of whether the calculated position of the center of pressure (COP) falls within the base of support (BOS) which outlines the subject’s feet. Motion capture data combined with biomechanical modeling and simulation allows the forces and moments between the human and the VIS platform to be computed and the position of the COP as well as the location and shape of the BOS to be determined. The goal of this study was to assess the accuracy of the COP trajectory calculated using motion capture-based data. METHODS AND RESULTS: To obtain the dynamic quantities from which COP is calculated, motion capture data is first collected in the 1g lab environment by recording the trajectories of passive retroreflective markers placed on a subject during exercise or performance of a given task. The OpenSim [1] inverse kinematics (IK) tool is used to fit a scaled subject model to recorded marker trajectories while minimizing marker error to obtain joint angles. Then, a custom OpenSim plugin [2] is used to determine the subject’s time-varying moment of inertia and its time derivative, center of mass (CM) position, velocity, and acceleration, as well as the angular momentum and its time derivative relative to the subject’s CM. Some of these quantities are not needed for modeling tasks performed on a stationary lunar surface but, due to the moving exercise platform, are needed to model VIS response to the subject’s motion. Hand positions, used in calculating a cable force if present, are recorded as well. These quantities are used to calculate the total force (F ⃗^((plate) )) and moment (M ⃗^((plate) )) exerted by the lunar surface or the VIS plate on the subject’s shoe soles. COP is then calculated from the following equations: r_x^((cop) )= M_z^((plate) )/F_y^((plate) ) and r_z^((cop) )= 〖-M〗_x^((plate) )/F_y^((plate) ), where the y axis is normal to the surface. COP accuracy for feasibility assessments is then determined by whether it falls within the BOS, which is also computed by the plugin. To study the accuracy of COP calculated from motion capture, we first investigated whether COP remained within the BOS, as it must, for exercises performed in the 1g lab environment. Standard exercises such as back squat and deadlift were analyzed, as well as more explosive exercises including hang clean and press. Cases in which the COP exited the BOS indicated that COP accuracy required further investigation. In this study, an exercise device with cables was used, so cable force modeling accuracy should also be considered. In a separate study, we collected motion capture and force plate data for twenty-seven motions not involving an exercise device. About a third were genuine countermeasures exercises (e.g., hang clean and press), some were relevant for lunar tasks (e.g., object pick up), and the rest were of a “unit test” nature (e.g., swaying back and forth or side to side). Motion capture-based COP positions were compared with force plate measured COP. We found that while force plate measured COP remained within the BOS, motion capture-based COP was observed to briefly exit the BOS on occasion. Techniques to mitigate IK artifacts and filtering of calculated data could be used to improve the agreement of calculated and measured results, resolving excursions from the BOS within this dataset. The mean error between calculated and measured COP was found to be less than 6 mm. Additionally, we derived and investigated equations for the COP in terms of the cable force, cable location, as well as the human CM position, acceleration, and angular momentum with respect to the CM, and analyzed them for sensitivity to errors in individual quantities. Several were found, but the most significant one was that when the vertical force on the feet approaches zero, indicating a near-detachment or ‘jump off’ condition, errors are amplified. This is consistent with the observation that in the absence of pressure, the concept of the center of pressure would become meaningless.

C A Bell↗
NASA NTRS1986

Design of multivariable controllers for robot manipulators

The paper presents a simple method for the design of linear multivariable controllers for multi-link robot manipulators. The control scheme consists of multivariable feedforward and feedback controllers. The feedforward controller is the minimal inverse of the linearized model of robot dynamics and contains only proportional-double-derivative (PD2) terms. This controller ensures that the manipulator joint angles track any reference trajectories. The feedback controller is of proportional-integral-derivative (PID) type and achieves pole placement. This controller reduces any initial tracking error to zero as desired and also ensures that robust steady-state tracking of step-plus-exponential trajectories is achieved by the joint angles. The two controllers are independent of each other and are designed separately based on the linearized robot model and then integrated in the overall control scheme. The proposed scheme is simple and can be implemented for real-time control of robot manipulators.

Seraji, H.↗
NASA NTRS2024

Redundancy Parameterization and Inverse Kinematics of 7-DOF Revolute Manipulators

Seven degree-of-freedom (DOF) robot arms have one redundant DOF for obstacle and singularity avoidance. This DOF does not change the end effector motion and must be parameterized to fully specify the joint angles for a given end effector pose. For 7-DOF revolute (7R) manipulators, we introduce the generalized shoulder-elbow-wrist (SEW) angle, a generalization of the widely-used conventional SEW angle but with an arbitrary reference direction function, along with Jacobian expressions and singularity analysis. Other redundancy parameterizations including the conventional SEW angle encounter an algorithmic singularity along a line in the workspace. We introduce a reference direction function choice called the stereographic SEW angle which has a singularity only along a half-line and can be placed out of reach. We prove such a singularity is unavoidable for any parameterization. Finally, using the general SEW angle and the subproblem decomposition method, we provide efficient singularity-robust inverse kinematics solutions for 7R manipulators which are often closed-form but may involve a 1D or (in general) 2D search. Search-based solutions may be converted to finding polynomial roots. Examples are available in a publicly accessible repository.

Kinematics↗
NASA NTRS2023

Damage Detection of a Pressure Vessel with Smart Sensing and Deep Learning

Structural Health Monitoring plays a crucial role in ensuring the safety and reliability of critical infrastructure, including pressure vessels involved in various applications. This research reports the damage detection of a pressure box employed in space habitat that operates in harsh environment where both structural failure and bolt joint loosening may occur. These failure modes are extremely hard to model based on first principles. We explore proper sensing mechanism and the associated inverse analysis algorithm that can elucidate the health condition of the pressure box. It is identified that piezoelectric impedance based active interrogation can provide necessary information for damage detection in such a system. Concurrently, deep learning technique leveraging spatial convolutional neural network is synthesized to analyze the raw data acquired and identify different types of damage. By training the deep learning model on a dataset of healthy and various damage scenarios, we can achieve high accuracy in identifying the presence of damage and its type. This research provides a data-driven methodology for structural damage detection using deep learning and has the potential to be extended to various systems with different failure modes.

Yang Zhang↗
DOE OSTI2024

GLAD-M35: a joint P and S global tomographic model with uncertainty quantification

We present our third and final generation joint P and S global adjoint tomography (GLAD) model, GLAD-M35, and quantify its uncertainty based on a low-rank approximation of the inverse Hessian. Starting from our second-generation model, GLAD-M25, we added 680 new earthquakes to the database for a total of 2160 events. New P-wave categories are included to compensate for the imbalance between P- and S-wave measurements, and we enhanced the window selection algorithm to include more major-arc phases, providing better constraints on the structure of the deep mantle and more than doubling the number of measurement windows to 40 million. Two stages of a Broyden–Fletcher–Goldfarb–Shanno (BFGS) quasi-Newton inversion were performed, each comprising five iterations. With this BFGS update history, we determine the model’s standard deviation and resolution length through randomized singular value decomposition.

58 GEOSCIENCES↗
NASA NTRS2006

Dynamic Inversion based Control of a Docking Mechanism

The problem of position and attitude control of the Stewart platform based docking mechanism is considered motivated by its future application in space missions requiring the autonomous docking capability. The control design is initiated based on the framework of the intelligent flight control architecture being developed at NASA Ames Research Center. In this paper, the baseline position and attitude control system is designed using dynamic inversion with proportional-integral augmentation. The inverse dynamics uses a Newton-Euler formulation that includes the platform dynamics, the dynamics of the individual legs along with viscous friction in the joints. Simulation results are presented using forward dynamics simulated by a commercial physics engine that builds the system as individual elements with appropriate joints and uses constrained numerical integration,

Kulkarni, Nilesh V.↗
NASA NTRS2006

Stochastic Evolutionary Algorithms for Planning Robot Paths

A computer program implements stochastic evolutionary algorithms for planning and optimizing collision-free paths for robots and their jointed limbs. Stochastic evolutionary algorithms can be made to produce acceptably close approximations to exact, optimal solutions for path-planning problems while often demanding much less computation than do exhaustive-search and deterministic inverse-kinematics algorithms that have been used previously for this purpose. Hence, the present software is better suited for application aboard robots having limited computing capabilities (see figure). The stochastic aspect lies in the use of simulated annealing to (1) prevent trapping of an optimization algorithm in local minima of an energy-like error measure by which the fitness of a trial solution is evaluated while (2) ensuring that the entire multidimensional configuration and parameter space of the path-planning problem is sampled efficiently with respect to both robot joint angles and computation time. Simulated annealing is an established technique for avoiding local minima in multidimensional optimization problems, but has not, until now, been applied to planning collision-free robot paths by use of low-power computers.

Fink, Wolfgang↗
NASA NTRS1992

Robot path planning for space-truss assembly

Construction, repair, and maintenance of space-based structures will require extensive planning of operations in order to effectively carry out these tasks. The path planning algorithm described here is a general approach to generating paths that guarantee collision avoidance for a single chain nonredundant or redundant robot. The algorithm uses a graph search of feasible points in position space, followed by a local potential field method that guarantees collision avoidance among objects, structures, and the robot arm as well as conformance to joint limit constraints. This algorithm is novel in its computation of goal attractive potential fields in Cartesian space, and computation of obstacle repulsive fields in robot joint space. These effects are combined to generate robot motion. Computation is efficiently implemented through the computation of the robot arm Jacobian and not the full inverse arm kinematics. These planning algorithms have been implemented and evaluated using existing space-truss designs, and are being integrated into the RPI-CIRSSE Testbed environment.

Muenger, Rolf↗