Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interface diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Electrode chemistry impact on retention performance of ferroelectric hafnium zirconium oxide (Hf 0.5 Zr 0.5 O 2−x ) capacitors

Polarization retention of 10 nm thick ferroelectric hafnium zirconium oxide (Hf 0.5 Zr 0.5 O 2−x , HZO) capacitors with W and TaN electrodes is investigated over temperatures ranging from 85 to 150 °C. Same state and opposite state polarization margins for devices with W electrodes show minimal retention loss after 10 5 at 150 °C. The devices capped with TaN electrodes show excellent same state retention, but the opposite state polarization margin in the TaN-electrode devices displays 40% retention loss at 150 °C after 10 5 s. The TaN-capped devices exhibit a more pronounced imprint, which is attributed to an increased oxygen vacancy content (compared to W-capped devices). The increased oxygen vacancy content in the TaN-capped devices is supported by photoluminescence and leakage current measurements. In addition, TaN-capped devices have chemically diffuse electrode–HZO interfaces; more abrupt interfaces are present in the W-capped devices. The presence of interfacial phases in the TaN-capped devices may lead to larger depolarization fields due to reduced charge screening. The results from this study provide further evidence that for HZO ferroelectric devices the electrode can significantly impact polarization retention behavior due to differences in oxygen vacancy concentration and formation of non-ferroelectric interfacial layers.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Photon Detection System Calibration for DUNE

Photon Detection System Calibration for DUNE Not scheduled 20m Conference Center (University of California, Irvine) Poster New Technologies for Neutrino Physics Poster session Speaker Denis Torres (South Dakota School of Mines and Technology) Description The Deep Underground Neutrino Experiment (DUNE) is a long baseline neutrino oscillation experiment that relies on a precise Photon Detection System (PDS) to provide accurate timing information, enhance sensitivity to low-energy and non-beam events, and support detector performance studies in liquid argon time projection chambers. Achieving these goals requires a well-understood and stable optical calibration strategy that operates reliably under cryogenic conditions. In this poster, I will present PDS calibration studies performed in ProtoDUNE, focusing on the characterization of the ultraviolet (UV) light calibration system and key optical components in the light-delivery chain. I will discuss measurements of optical fiber transmission, SMA-to-SMA connector and feedthrough interface losses, and diffuser assemblies, emphasizing wavelength dependence, attenuation, and performance under cryogenic thermal cycling and stability tests. These studies provide quantitative inputs for understanding light transport, uniformity, and long-term reliability of the PDS in large-scale liquid argon detectors, and they directly inform calibration strategies for the DUNE Far Detector.

Torres Muñoz, Denis [South Dakota Sch. Mines Tech.↗
NASA NTRS1973

The nature of dark-etching rims in meteoritic taenite.

Taenite fields when etched develop a cloudy brown rim with approximate compositional limits of 25 and 40% Ni. In iron meteorites this cloudy zone is only a few microns wide, with a sharp, high-Ni edge about 1 micron from the kamacite interface and a diffuse edge several microns from the central plessite. It is always present in irons unless the meteorite has been cosmically or terrestrially reheated. X-ray and electron diffraction of grains scratched from exceptionally larger areas of cloudy taenite in the mesosiderite Estherville show that this etching zone contains a fine exsolution of kamacite. Detailed electron-probe investigations of taenite in Estherville show that there is a step in the M-shaped Ni profile at the sharp, high-Ni edge of the cloudy region, the Ni dropping suddenly from approximately 45 to 42%. It is proposed that exsolution in the cloudy region effectively froze in the Ni profile at that temperature. On subsequent cooling only the clear outer taenite continued to equilibrate with the kamacite matrix, producing the kink in the M profile. Cloudy taenite is therefore a variety of plessite differing from the usual varieties in that it forms at lower temperatures in areas much richer in Ni, and the morphology is not crystallographically oriented. Its absence can provide a sensitive indication of reheating.

Scott, E. R. D.↗
NASA NTRS1982

Dual alloy interface stability

Powder metallurgy dual alloy fabrication is applied to combinations of superalloys having a high iron, and low strategic metal content, with standard nickel base superalloys, containing the strategic metals chromium, cobalt, and columbium. The possibility of combining Alloy 901 (12 percent Cr, 36 percent Fe, 0 percent Co, and 0 percent Cb) with turbine disk alloys Rene 95 (13 percent Cr, 8 percent Co, and 4 percent Cb) or low carbon astroloy (L.C.A.; 15 percent Cr, 17 percent Co, and 0 percent Cb) is investigated. Preliminary results for combinations show that a strong interface with rapid diffusion is obtained between alloys and that the standard heat treatments for either alloy may be satisfactory.

Harf, F. H.↗
NASA NTRS1982

Combustion system for radiation investigations

An inlet interface flange, inlet diffuser, fuel struts and nozzles, combustor liner, liner housing and exhaust flange comprise a system to be installed in an existing test facility. The system was designed for operation at 40 atmospheres inlet pressure, 900 K inlet temperature, and air flow to 80 kg/sec. Six penetrations are provided in the outer pressure housing. Adapters at the penetrations, permit use of various types of radiation instrumentation. Five total radiation radiometers and two heat flux gases were installed. Rotating exhaust instrumentation can also be used to determine combustor performance. Data are presented showing total radiation at three axial positions of the combustor, and comparison of total radiation with data from a heat flux gage.

Wear, J. D.↗
NASA NTRS1986

Physics through the 1990s: Condensed-matter physics

The volume presents the current status of condensed-matter physics from developments since the 1970s to opportunities in the 1990s. Topics include electronic structure, vibrational properties, critical phenomena and phase transitions, magnetism, semiconductors, defects and diffusion, surfaces and interfaces, low-temperature physics, liquid-state physics, polymers, nonlinear dynamics, instabilities, and chaos. Appendices cover the connections between condensed-matter physics and applications of national interest, new experimental techniques and materials, laser spectroscopy, and national facilities for condensed-matter physics research. The needs of the research community regarding support for individual researchers and for national facilities are presented, as are recommendations for improved government-academic-industrial relations.

Source record↗
NASA NTRS1992

The semicircular shell of CTB 109

The radio and X-ray images of the supernova remnant CTB 109 have the morphology of a semicircular shell. It is shown that such a structure is a natural result of a supernova explosion that occurred 3,000 yr ago near an interface between the diffuse interstellar medium and a dense molecular cloud. The calculated X-ray, infrared, and radio fluxes agree fairly well with the observed values.

Wang, Zhenru↗
NASA NTRS2003

Use of Plastic Capillaries for Macromolecular Crystallization

Methods of crystallization of biomolecules in plastic capillaries (Nalgene 870 PFA tubing) are presented. These crystallization methods used batch, free-interface liquid- liquid diffusion alone, or a combination with vapor diffusion. Results demonstrated growth of crystals of test proteins such as thaumatin and glucose isomerase, as well as protein studied in our laboratory such dihydrolipoamide dehydrogenase. Once the solutions were loaded in capillaries, they were stored in the tubes in frozen state at cryogenic temperatures until the desired time of activation of crystallization experiments.

Potter, Rachel R.↗
DOE OSTI2025

An extension of the localized artificial diffusivity method for immiscible and high density ratio flows

The localized artificial diffusivity (LAD) method is widely regarded as the preferred multi-material regularization scheme for the compact finite difference method, because it is conservative, easy to implement, and generally robust for a wide range of multi-material problems. However, traditional LAD methods face significant challenges when applied to flows with large density ratios and when maintaining thermodynamic equilibrium across material interfaces. These limitations arise from the formulation of the artificial diffusivity flux and the reliance on enthalpy diffusion for interface regularization. Additionally, traditional LAD methods struggle to ensure stability under large density ratio conditions, fail to maintain a finite interface thickness, and are therefore unsuitable for modeling immiscible interfaces. Here, in this work, we discuss the origins of these issues in traditional LAD methods and propose modifications which enable the simulation of large density ratio and immiscible flows. The proposed method targets the artificial diffusion fluxes at gradients and ringing in the volume fraction, rather than the mass fraction in traditional methods, to consistently regularize large density ratio interfaces. Furthermore, the proposed method introduces an artificial bulk density diffusion term to enforce equilibrium conditions across interfaces. To address the challenge of modeling immiscible flows, a conservative diffuse interface term is incorporated into the formulation to ensure a finite interface thickness. Specific consideration is taken in the design of the method to ensure that these crucial properties are maintained for N -material flows. The effectiveness of the proposed method is demonstrated through a series of canonical test cases, and its accuracy is validated by comparison with experimental data on micro-bubble collapse in water. These results highlight the method’s robustness and its ability to overcome the limitations of traditional LAD approaches.

Artificial diffusivity↗
NASA NTRS1999

Analysis of X-Ray Microradiographs of Al-Au Interface Quench Profile using Modeling of Solidification Including Double-Diffusion and Convection in the Melt

Experimental data on Al-0.8Au horizontal solidification of a 1 mm thick specimen in a BN crucible shows the effect of growth rate on the solidification interface shape. For translation rates below 0.5 micron/s the interface maintains a plain and flat shape. When the translation rate is 3 to 5 micron/s or more, the interface appearance changes to two planar zones, with the zone closer to the bottom having higher inclination. The interface shapes were measured by first quenching in place during growth. X-ray microscopy shows the interface shape within the quenched sample by viewing through the side of the specimen. In order to provide theoretical explanation of the phenomena, numerical modeling was undertaken using finite element code FIDAP. Double diffusion convection in Al-0.8Au melt and crystal-melt interface curvature during directional solidification was analyzed numerically. Actual thermophysical properties of Al-0.8Au including the binary Al-Au phase diagram were used. Although convection in the sample is weak, for the slower translation rate convection and diffusion is sufficient for the redistribution of initial compositional stratification caused by gravity. When translation rate is raised, neither convection nor diffusion can provide proper mixing so that solidification temperatures differ significantly near the bottom within the bulk of the sample. As a result, the solid-liquid interface appears to have two planar zones with different inclination.

Bune, Andris V.↗
DOE OSTI2024

Electric field enhanced diffusion welding of alloy 617: Microstructural characteristics and mechanical properties

This study investigated the microstructural characteristics and mechanical behavior of diffusion welded nickel-based Alloy 617 obtained by electric field-assisted sintering (EFAS) using various parameters. The interfacial microstructure exhibited different characteristics including good grain boundary (GB) migration across the interface in the samples diffusion-welded at 1100 °C and a flat interface in the samples joined at 1000 °C and 1050 °C. The interface consisted of fine Al 2 O 3 oxides, while precipitation of interfacial M 23 C 6 carbides was not observed. Grain boundaries migrated across the Al 2 O 3 oxides, leaving these oxides within the grains. Graded grain size was observed, with grain coarsening being more significant near the sample surface due to the temperature gradient induced by EFAS. Tensile testing revealed that the specimens fractured in the matrix away from the interface, indicting strong diffusion-welded joints. Further, the peak tensile strength of 807 MPa was obtained in the samples welded at 1000 °C due to minimal grain growth. The materials obtained at 1100 °C exhibited reduced tensile strength but improved ductility. Strain maps revealed by digital image correlation showed alternating high and low strain segments in the samples produced at 1000 °C and 1050 °C, indicating that the flat interfaces with no GB migration were less ductile compared to the matrix. A greater strain uniformity was observed along the bond interfaces with improved GB migration. The hardness reduced near the sample surfaces due to enlarged grains induced by temperature gradient. This study demonstrates that GB migration and enhanced mechanical strength can be achieved in diffusion-welded Alloy 617.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Manipulating the diffusion energy barrier at the lithium metal electrolyte interface for dendrite-free long-life batteries

Abstract Constructing an artificial solid electrolyte interphase (SEI) on lithium metal electrodes is a promising approach to address the rampant growth of dangerous lithium morphologies (dendritic and dead Li 0 ) and low Coulombic efficiency that plague development of lithium metal batteries, but how Li + transport behavior in the SEI is coupled with mechanical properties remains unknown. We demonstrate here a facile and scalable solution-processed approach to form a Li 3 N-rich SEI with a phase-pure crystalline structure that minimizes the diffusion energy barrier of Li + across the SEI. Compared with a polycrystalline Li 3 N SEI obtained from conventional practice, the phase-pure/single crystalline Li 3 N-rich SEI constitutes an interphase of high mechanical strength and low Li + diffusion barrier. We elucidate the correlation among Li + transference number, diffusion behavior, concentration gradient, and the stability of the lithium metal electrode by integrating phase field simulations with experiments. We demonstrate improved reversibility and charge/discharge cycling behaviors for both symmetric cells and full lithium-metal batteries constructed with this Li 3 N-rich SEI. These studies may cast new insight into the design and engineering of an ideal artificial SEI for stable and high-performance lithium metal batteries.

25 ENERGY STORAGE↗
NASA NTRS1993

The Fe2(+)-Mg interdiffusion in orthopyroxene: Constraints from cation ordering and structural data and implications for cooling rates of meteorites

Orthopyroxene crystals in a number of meteorites exhibit compositional zoning of Fe and Mg, which provide important constraint on their cooling rates. However, attempts to model cooling rate of these crystals from Fe-Mg zoning profiles suffer from the lack of any measured or theoretically well constrained Fe-Mg interdiffusion data in OP(x) It has been assumed that Fe-Mg interdiffusion in OP(x) only slightly slower than that in olivine. The purpose of this paper is to (1) calculate the Fe-Mg fractionation, and (2) provide analytical formulation relating cooling rate to the length of the diffusion zone across the interface of the overgrowth of a mineral on itself with application to Mg diffusion profile across OP(x) growth on OP(x) in certain mesosiderites.

Ganguly, J.↗
DOE OSTI2026

Extending SLUSCHI for Automated Diffusion Calculations

We present an extension of the SLUSCHI package (Solid and Liquid in Ultra Small Coexistence with Hovering Interfaces) to enable automated diffusion calculations from first-principles molecular dynamics. While the original SLUSCHI workflow was designed for melting temperature estimation via solid-liquid coexistence, we adapt its input and output handling to isolate the volume search stage and generate one production trajectory suitable for diffusion analysis. Post-processing tools parse VASP outputs, compute mean-square displacements (MSD), and extract tracer diffusivities using the Einstein relation with robust error estimates through block averaging. Diagnostic plots, including MSD curves, running slopes, and velocity autocorrelations, are produced automatically to help identify diffusive regimes. The method has been validated through representative case studies: self-diffusion in Al-Cu liquid alloys, sublattice melting in Li7La3Zr2O12 and Er2O3, interstitial oxygen transport in bcc and fcc Fe, and oxygen diffusivity in Fe-O liquids with variable Si and Al contents. Viscosity and diffusivity are linked through the Stokes-Einstein relation, with composition dependence assessed via simple linear mixing. This capability broadens SLUSCHI from melting-point predictions to transport property evaluation, enabling high-throughput, fully first-principles datasets of diffusion coefficients and viscosities across metals and oxides.

36 MATERIALS SCIENCE↗
DOE OSTI2025

An Atomistic Study of Reactivity in Solid-State Electrolyte Interphase Formation for Li/Li7P3S11

Lithium metal batteries offer superior volumetric and gravimetric specific capacities compared to those based on traditional graphite anodes. Although advancements in solid-state electrolytes address safety concerns, challenges remain, particularly regarding interphase formation in lithium metal anodes. This work presents a computational framework based on high-throughput first-principles density functional theory and machine-learning interatomic potentials (MLIPs) including automated iterative, active learning to enable robust computational exploration of interphase formation between lithium metal anodes and an inorganic solid-state electrolyte. As a demonstration, we apply the framework to a Li/Li7P3S11 interface and find that it accurately identifies the experimentally observed, thermodynamically stable interphase products as well as their overall spatial arrangement within a heterogeneous, amorphous layered structure, with Li2S domains of nanocrystallinity. Our simulations show two stages, a fast and slow diffusion reaction regime, that corroborate the relative phase formation rate of Li x P, Li2S, and Li3P. Using the Onsager transport theory, we capture time-dependent ionic diffusion within the reacting interface, including cross-correlation effects. We found that cross-correlation effects between Li-P and P-S ionic motion significantly influence P-ion diffusion, making it highly sensitive to the local environment and potentially leading to "kinetic trapping" of Li-P phases. The passivation of the interface is shown as the ionic fluxes all approach zero, effectively halting interphase growth.

Diffusion↗
DOE OSTI2025

Multimaterial 3D Printing in Activating Bath Enables In Situ Polymerization of Thermosets with Intricate Geometries and Diverse Elastic Behaviors

Polydicyclopentadiene, p(DCPD), is a high‐performance thermoset valued for its exceptional toughness, strength, and stiffness. When copolymerized with 1,5‐cyclooctadiene (COD), its mechanical properties can be tuned from glassy to rubbery at room temperature. While frontal polymerization enables a rapid and energy‐efficient route to 3D print DCPD‐based materials, challenges such as ink shelf life and gravitational distortion, especially in direct ink writing of soft COD‐rich formulations, must be considered. Here, a complementary chemical strategy is presented, embedded 3D printing, that enables localized in situ polymerization of printed DCPD/COD inks within a reactive support matrix. The matrix provides both physical support and a reservoir of chemical activator, which diffuses into the ink, activates a latent bis(N‐heterocyclic carbene) Ru precatalyst, and initiates ring‐opening metathesis polymerization. Curing begins at the ink–matrix interface and propagates inward via diffusion, stabilizing the interface and preventing capillary‐driven deformation regardless of the matrix yield stress. This approach eliminates the need for cold storage, external curing, or photoinitiation, significantly expanding the processing window. Using this method, diverse thermosetting and elastomeric architectures are fabricated with features as small as 5 µm and aspect ratios of 100, including interlinked chains, shallow spherical shells exhibiting snap‐through buckling, and hair‐like fin arrays inaccessible through traditional techniques.

chemical activation↗
NASA NTRS1998

Temperature Dependence of Diffusion and Reaction at a Pd/SiC Contact

Schottky diodes of Palladium/SiC are good candidates for hydrogen and hydrocarbon gas sensors at elevated temperature. The detection sensibility of the diodes has been found heavily temperature dependent. In this work, emphasis has been put on the understanding of changes of physical and chemical properties of the Schottky diodes with variation of temperature. Schottky diodes were made by depositing ultra-thin palladium films onto silicon carbide substrates. The electrical and chemical properties of Pd/SiC Schottky contacts were studied by XPS and AES at different annealing temperatures. No significant change in the Schottky barrier height of the Pd/SiC contact was found in the temperature range of RT-400 C. However, both palladium diffused into SiC and silicon migrated into palladium thin film as well as onto surface were observed at room temperature. The formation of palladium compounds at the Pd/SiC interface was also observed. Both diffusion and reaction at the Pd/SiC interface became significant at 300 C and higher temperature. In addition, silicon oxide was found also at the interface of the Pd/SiC contact at high temperature. In this report, the mechanism of diffusion and reaction at the Pd/SiC interface will be discussed along with experimental approaches.

Shi, D.T.↗