Results for “installed base” — Page 10

NASA NTRS1985

Methods for heat transfer and temperature field analysis of the insulated diesel phase 2 progress report

This report describes work done during Phase 2 of a 3 year program aimed at developing a comprehensive heat transfer and thermal analysis methodology for design analysis of insulated diesel engines. The overall program addresses all the key heat transfer issues: (1) spatially and time-resolved convective and radiative in-cylinder heat transfer, (2) steady-state conduction in the overall structure, and (3) cyclical and load/speed temperature transients in the engine structure. During Phase 2, radiation heat transfer model was developed, which accounts for soot formation and burn up. A methodology was developed for carrying out the multi-dimensional finite-element heat conduction calculations within the framework of thermodynamic cycle codes. Studies were carried out using the integrated methodology to address key issues in low heat rejection engines. A wide ranging design analysis matrix was covered, including a variety of insulation strategies, recovery devices and base engine configurations. A single cylinder Cummins engine was installed at Purdue University, and it was brought to a full operational status. The development of instrumentation was continued, concentrating on radiation heat flux detector, total heat flux probe, and accurate pressure-crank angle data acquisition.

Morel, T.↗

NASA NTRS1993

Digital control of magnetic bearings supporting a multimass flexible rotor

The characteristics of magnetic bearings used to support a three mass flexible rotor operated at speeds up to 14,000 RPM are discussed. The magnetic components of the bearing are of a type reported in the literature previously, but the earlier analog controls were replaced by digital ones. Analog-to-digital and digital-to-analog converters and digital control software were installed in an AT&T PC. This PC-based digital controller was used to operate one of the magnetic bearings on the test rig. Basic proportional-derivative control was applied to the bearings, and the bearing stiffness and damping characteristics were evaluated. Particular attention is paid to the frequency dependent behavior of the stiffness and damping properties, and comparisons are made between the actual controllers and ideal proportional-derivative control.

Keith, F. J.↗

NASA NTRS1994

Monitoring Integrity Of Composite Aircraft Components

System developed that monitors integrity of composite-material structural components of aircraft in service. Includes strain gauges and accelerometers installed permanently in components to monitor vibrations, microprocessor-based data-acquisition system to process outputs of these vibration sensors, and desktop computer to analyze acquired data. By automating significant part of inspection process, system reduces amount of time needed for inspection and cost of inspection equipment. Contributes to safety by giving timely warning of hidden flaws that necessitate early, detailed inspection of critical components to determine whether components should be replaced immediately.

Tang, Shu Shing↗

NASA NTRS1995

Verification Test of Automated Robotic Assembly of Space Truss Structures

A multidisciplinary program has been conducted at the Langley Research Center to develop operational procedures for supervised autonomous assembly of truss structures suitable for large-aperture antennas. The hardware and operations required to assemble a 102-member tetrahedral truss and attach 12 hexagonal panels were developed and evaluated. A brute-force automation approach was used to develop baseline assembly hardware and software techniques. However, as the system matured and operations were proven, upgrades were incorporated and assessed against the baseline test results. These upgrades included the use of distributed microprocessors to control dedicated end-effector operations, machine vision guidance for strut installation, and the use of an expert system-based executive-control program. This paper summarizes the developmental phases of the program, the results of several assembly tests, and a series of proposed enhancements. No problems that would preclude automated in-space assembly or truss structures have been encountered. The test system was developed at a breadboard level and continued development at an enhanced level is warranted.

Rhodes, Marvin D.↗

NASA NTRS1981

Profit from a Problem

The Refuse-fired Steam Generating Facility was jointly sponsored by Hampton, NASA Langley and Langley Air Force Base. The facility disposes of all solid waste from the NASA Center, the Air Force Base, the Army's Fort Monroe and other federal installations in the area, and accommodates about 70 percent of Hampton's municipal waste. Incinerated refuse is reduced to a readily-disposable ash whose volume is one-seventh that of the solid waste brought to the plant. The energy produced in the burning process is converted to steam for use in research and administrative facilities at Langley Research Center. Plant is expected to produce some 300 million pounds of steam annually, about 85 percent of Langley Research Center's needs.

Source record↗

NASA NTRS2005

Electronic Router

Electronic Router (E-Router) is an application program for routing documents among the cognizant individuals in a government agency or other organization. E-Router supplants a prior 14 NASA Tech Briefs, May 2005 system in which paper documents were routed physically in packages by use of paper slips, packages could be lost, routing times were unacceptably long, tracking of packages was difficult, and there was a need for much photocopying. E-Router enables a user to create a digital package to be routed. Input accepted by E-Router includes the title of the package, the person(s) to whom the package is to be routed, attached files, and comments to reviewers. Electronic mail is used to notify reviewers of needed actions. The creator of the package can, at any time, see the status of the package in the routing structure. At the end of the routing process, E-Router keeps a record of the package and of approvals and/or concurrences of the reviewers. There are commercial programs that perform the general functions of E-Router, but they are more complicated. E-Router is Web-based, easy to use, and does not require the installation or use of client software.

Crusan, Jason↗

NASA NTRS2013

A Fiber-Optic Aircraft Lightning Current Measurement Sensor

A fiber-optic current sensor based on the Faraday Effect is developed for aircraft installations. It can measure total lightning current amplitudes and waveforms, including continuing current. Additional benefits include being small, lightweight, non-conducting, safe from electromagnetic interference, and free of hysteresis and saturation. The Faraday Effect causes light polarization to rotate in presence of magnetic field in the direction of light propagation. Measuring the total induced light polarization change yields the total current enclosed. The system operates at 1310nm laser wavelength and can measure approximately 300 A - 300 kA, a 60 dB range. A reflective polarimetric scheme is used, where the light polarization change is measured after a round-trip propagation through the fiber. A two-detector setup measures the two orthogonal polarizations for noise subtraction and improved dynamic range. The current response curve is non-linear and requires a simple spline-fit correction. Effects of high current were achieved in laboratory using combinations of multiple fiber and wire loops. Good result comparisons against reference sensors were achieved up to 300 kA. Accurate measurements on a simulated aircraft fuselage and an internal structure illustrate capabilities that maybe difficult with traditional sensors. Also tested at a commercial lightning test facility from 20 kA to 200 kA, accuracy within 3-10% was achieved even with non-optimum setups.

Nguyen, Truong X.↗

NASA NTRSDate not supplied

Developing a Vision for Maturing the Heliophysics Infrastructure towards Open Science: The DIARieS Analysis Ecosystem

In the dawn of open science and the upcoming requirements, we speak about the existing state of Heliophysics infrastructure and detail the evolution required to address capability or interconnection shortcomings. Such a daunting barrier calls for an analysis ecosystem with multi-faceted capability. We propose such an ecosystem, called DIARieS, to be built upon five conceptual pillars: Discovery, Implementation, Analysis, Reproducibility, and Sharing of results. The combination of these concepts in a single platform will enable users to more intuitively combine recent advances in technology to create ‘DIARieS’ of their workflows, which can be easily made open to others in the community. The DIARieS ecosystem will also increase our efficiency by streamlining our various workflow processes, including automatic incorporation of the impending requirements of open science. The various components of the ecosystem will simplify software installation and data implementation, including automatically generated citation lists based on the components included. Automatic containerization and version control of the ecosystem will make the custom workflows easily reproducible. Employing widget technology will ease the difficulty of producing publication and commercial quality visualizations and applying common analyses techniques. Incorporating multiple technologies will streamline the various sharing methods common in our work environments today. Overall, the totality of capabilities to be offered by this analysis ecosystem will drastically simplify the application of open science principles to our work in addition to improving our efficiency and ease of collaboration. This talk summarizes a vision of the proposed ecosystem, which is described in more detail in Ringuette et al. (2022: https://doi.org/10.1016/j.asr.2022.05.012).

infrastructure↗

NASA NTRSDate not supplied

Developing a Vision for Maturing the Heliophysics Infrastructure towards Open Science

In the dawn of open science and the upcoming requirements, we speak about the existing state of Heliophysics infrastructure and detail the evolution required to address capability or interconnection shortcomings. Such a daunting barrier calls for an analysis ecosystem with multi-faceted capability. We propose such an ecosystem, called DIARieS, to be built upon five conceptual pillars: Discovery, Implementation, Analysis, Reproducibility, and Sharing of results. The combination of these concepts in a single platform will enable users to more intuitively combine recent advances in technology to create ‘DIARieS’ of their workflows, which can be easily made open to others in the community. The DIARieS ecosystem will also increase our efficiency by streamlining our various workflow processes, including automatic incorporation of the impending requirements of open science. The various components of the ecosystem will simplify software installation and data implementation, including automatically generated citation lists based on the components included. Automatic containerization and version control of the ecosystem will make the custom workflows easily reproducible. Employing widget technology will ease the difficulty of producing publication and commercial quality visualizations and applying common analyses techniques. Incorporating multiple technologies will streamline the various sharing methods common in our work environments today. Overall, the totality of capabilities to be offered by this analysis ecosystem will drastically simplify the application of open science principles to our work in addition to improving our efficiency and ease of collaboration.

Infrastructure↗

NASA NTRS2016

Space Launch System Base Heating Test: Tunable Diode Laser Absorption Spectroscopy

This paper describes the Tunable Diode Laser Absorption Spectroscopy (TDLAS) measurement of several water transitions that were interrogated during a hot-fire testing of the Space Launch Systems (SLS) sub-scale vehicle installed in LENS II. The temperature of the recirculating gas flow over the base plate was found to increase with altitude and is consistent with CFD results. It was also observed that the gas above the base plate has significant velocity along the optical path of the sensor at the higher altitudes. The line-by-line analysis of the H2O absorption features must include the effects of the Doppler shift phenomena particularly at high altitude. The TDLAS experimental measurements and the analysis procedure which incorporates the velocity dependent flow will be described.

Parker, Ron↗

NASA NTRS2016

Space Launch System Base Heating Test: Tunable Diode Laser Absorption Spectroscopy

This paper describes the Tunable Diode Laser Absorption Spectroscopy (TDLAS) measurement of several water transitions that were interrogated during a hot-fire testing of the Space Launch Systems (SLS) sub-scale vehicle installed in LENS II. The temperature of the recirculating gas flow over the base plate was found to increase with altitude and is consistent with CFD results. It was also observed that the gas above the base plate has significant velocity along the optical path of the sensor at the higher altitudes. The line-by-line analysis of the H2O absorption features must include the effects of the Doppler shift phenomena particularly at high altitude. The TDLAS experimental measurements and the analysis procedure which incorporates the velocity dependent flow will be described.

Parker, Ron↗

NASA NTRS1988

Contraction design for small low-speed wind tunnels

An iterative design procedure was developed for two- or three-dimensional contractions installed on small, low-speed wind tunnels. The procedure consists of first computing the potential flow field and hence the pressure distributions along the walls of a contraction of given size and shape using a three-dimensional numerical panel method. The pressure or velocity distributions are then fed into two-dimensional boundary layer codes to predict the behavior of the boundary layers along the walls. For small, low-speed contractions it is shown that the assumption of a laminar boundary layer originating from stagnation conditions at the contraction entry and remaining laminar throughout passage through the successful designs if justified. This hypothesis was confirmed by comparing the predicted boundary layer data at the contraction exit with measured data in existing wind tunnels. The measured boundary layer momentum thicknesses at the exit of four existing contractions, two of which were 3-D, were found to lie within 10 percent of the predicted values, with the predicted values generally lower. From the contraction wall shapes investigated, the one based on a fifth-order polynomial was selected for installation on a newly designed mixing layer wind tunnel.

Bell, James H.↗

NASA NTRS1971

Development of a High Temperature Heater using an Yttria Stabilized Zirconia Cored Brick Matrix

The Ames pilot heater is a ceramic regenerative heater that provides high temperature air for aerodynamic and combustion experiments. The development of this heater to provide a heat storage bed with temperature capability of about 4600 R is described. A bed was designed and installed having cored brick elements of yttria-stabilized zirconia. The bed dimensions were 14 inches in diameter by 10 feet high. The thermal stress limitations of the bed were studied and maximum air flow rates based upon these limits were established. A combustion reheat system was designed and installed to provide the necessary control over the bed temperature distribution. The revised heater system was successfully operated at a maximum bed temperature of 4600 R. The successful operation demonstrated that yttria-stabilized zirconia cored brick can satisfy the high temperature-long duration requirement for storage heater applications.

Smith, K. W.↗

NASA NTRS1980

The 737 graphite composite flight spoiler flight service evaluation

The flight service experience of 111 graphite-epoxy spoilers on 737 transport aircraft and related ground based enviromental exposure of graphite-epoxy material specimens is reported. Spoilers were installed on 28 aircraft representing seven major airlines operating throughout the world. Over 1,188,367 spoiler flight hours and 1,786,837 spoiler landings were accumulated by this fleet. Tests of removed spoilers and ground-based exposure specimens after the fifth year of service indicate modest changes in composite strength properties. Two incidents of trailing edge delamination with subsequent core corrosion were observed. Based on visual, ultrasonic, and destructive testing, there has been no evidence of moisture migration into the honeycomb core and no core corrosion.

Hoffman, D. J.↗

NASA NTRS1975

The 737 graphite composite flight spoiler flight service evaluation

The flight service experience of 108 graphite-epoxy spoilers on 737 transport aircraft, and related ground-based environmental exposure of graphite-epoxy material specimens were evaluated. Four spoilers were installed on each of 27 aircraft for a 5-year study. As of February 28, 1975, a total of 294,280 spoiler flight-hours and 460,686 spoiler landings were accumulated. Based on visual, ultrasonic, and destructive testing, no moisture migration into the honeycomb core and no core corrosion has occurred. Tests of removed spoilers and of ground-based exposure specimens after the first year of service indicate no significant changes in composite strength.

Stoecklin, R. L.↗

NASA NTRS1994

Lighting installations

Model computations that give the lay-out of a lighting installation have to be implemented in the real world. There, deviations from the ideal performance of just about every element of the installation will be felt. A list of possible sources of non-ideal behavior, based on practical experience, are: lamps, ballasts, reflectors, mounting position, sagging of lamps, and soiling. It is clear that with all possible deviations from the ideal the homogeneity of a real lighting installation can never be as good as the one computed. The only way to make sure it is nearly as good is by measurement of the actual light distribution. Then, an occasional adjustment or replacement may often yield a satisfactory result. This measurement should really be part of the installation contract.

Schurer, Kees↗

NASA NTRS2012

Thermostructural Analysis of the SOFIA Fine Field and Wide Field Imagers Subjected to Convective Thermal Shock

The Stratospheric Observatory For Infrared Astronomy (SOFIA) is a highly modified Boeing 747-SP with a 17- ton infrared telescope installed in the aft portion of the aircraft. Unlike ground- and space-based platforms, SOFIA can deploy to make observations anytime, anywhere, in the world. The originally designed aircraft configuration included a ground pre-cool system, however, due to various factors in the history of the project, that system was not installed. This lack of ground pre-cooling was the source of the concern about whether or not the imagers would be exposed to a potentially unsafe thermostructural environment. This concern was in addition to the already-existing concern of some project members that the air temperature rate of change during flight (both at the same altitude as well as ascent or descent) could cause the imagers to be exposed to an unsafe thermostructural environment. Four optical components were identified as the components of concern: two of higher concern (one in each imager), and two of lower concern (one in each imager). The analysis effort began by analyzing one component, after which the analyses for the other components was deemed unnecessary. The purpose of this report is to document these findings as well as lessons learned from the effort.

Kostyk, Christopher B.↗

NASA NTRS2019

New Perspectives for Watering Substrate-Based Root Modules in Microgravity in the Advanced Plant Habitat (APH)

The Advanced Plant Habitat (APH) was installed on the International Space Station (ISS) in October 2017. Following a successful EVT (Experiment Verification Test) study at Kennedy Space Center (KSC), using Arabidopsis lines with varying levels of lignin, two inaugural studies were carried out on ISS in 2018 under the same experimental design, with the corresponding ground controls at KSC. The APH for this study deploys a substrate-based root module designed for plant growth in microgravity. Upon experiment initiation (such as for the EVT), the root module is primed (liquid imbibition) by flooding the root zone to initiate seed germination and to remove air from the porous tubing and particulate media. In the APH ISS inaugural study, the speed of supplying water to initially dry media was found to adversely affect the overall moisture distribution within the root module in microgravity (but not at 1g). Non-destructive estimations of Arabidopsis plant growth were carried out by monitoring changes in rosette leaf area on a daily basis. These data indicated that the original priming procedure caused patchy moisture distribution that affected plant growth and survival. An improved methodology for priming the second root module of PH-01 was devised and implemented in the second experiment. Leaf area and color estimates suggested that the modified priming scheme improved moisture distribution and plant growth. These data, when compared with the EVT study, suggest that nondestructive measurements of plant growth can aid towards optimization of plant growth conditions in microgravity.

Monje O.↗