Preliminary Evaluation of a Number of Ablative Heat-shield Materials Exposed to Combined Radiative and Convective Heating
Ablating materials tested at combined radiative and convective heating for manned reentry vehicle heat shields
REENTRY VEHICLE↗
SEARCH · Engineering Papers
Results for “heating”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Experimental Observations of Aerodynamic and Heating Test on Insulating Heat Shields
Several different types of insulating heat shields have been subjected to aerodynamic tests and radiant-heating tests in order to obtain a better insight into the problems involved when the primary structure of m aerodynamically heated vehicle is substantially cooler than the exposed external surface. One of the main problems was considered to be a proper allowance for thermal expansion caused by these large temperature differences, so that undue distortion or thermal stresses would not occur in either the outer shield or the underlying structure. corrugated outer skin with suitably designed expansion joints was a feature of all the specimens tested.
Anderson, Melvin S.↗
Investigation of the hydrodynamics and heat transfer in a channel with turbulizers on the heat transfer surface
Hydrodynamics and heat transfer of heated air flowing in tube with turbilizers on heat transfer surface
Karasev, E. K.↗
Analysis of turbulent liquid-metal heat transfer in channels with heat sources in the fluid power-law velocity profile
Heat transfer characteristics for turbulent flow of heat generating liquid metals between parallel plates with wall heat transfer
Inman, R. M.↗
Local heat transfer for water in entrance regions of tubes with tapered flow areas and nonuniform heat fluxes
Convective heat transfer data for water flow in heated circular tubes with varying heat fluxes and flow areas
Sekas, N. J.↗
Heat and mass transfer in the vicinity of the vapor-gas front in a gas loaded heat pipe
Axially conducting gas controlled heat pipes leading to predictive capability for heat and mass transfer along heat pipe
Edwards, D. K.↗
Thermal Analysis Methods and Basic Heat-Transfer Data for a Turbulent Heating Flight Experiment at Mach 20 (Reentry F)
A heat-transfer experiment was flight conducted on a 5 deg half-angle cone, 396.2 cm (13 ft) in length, as it entered the sensible atmosphere under laminar, transitional, and turbulent boundary-layer conditions at a free-stream Mach number of about 20. Accurate turbulent-heat-transfer data with natural transition were obtained for correlation with theories in regions of simultaneous high Mach number, Reynolds number, enthalpy, and total-to-wall temperature ratio. Temperatures were measured at four depths through the 15.24-mm-thick (0.600-in.) beryllium wall. Experimental heating rates at 20 stations on the cone were determined independently from the outermost temperature measurement and from the temperature measurement at the second depth by a single-thermocouple inverse method and also from the temperature histories at all four depths by an integral method. The thermal data analysis procedure, associated problems, and results are presented herein.
Howard, Floyd G.↗
An out-of-core version of a six cell heat-pipe heated thermionic converter array
A thermionic system concept is described which incorporates a heat-pipe cooled fast spectrum reactor and six-cell thermionic converter modules located in the space radiator. Much of the technology being developed for the in-core thermionic reactor concept is directly applicable to this out-of-core concept, particularly the fuel and converter development activity. The major technology extension required is in the area of heat-pipes for cooling the reactor and carrying thermal energy from the reactor station to the converters. The performance characteristics of an out-of-core thermionic system at power levels between 40 and 70 kWe are summarized, the adaptation of in-core technology to the out-of-core concept is described and applicable heat-pipe technology programs now underway are discussed.
Kroeger, E. W.↗
Resistance heating elements with specific heating profiles
Bundled, interrupted, resistance heating elements provide specific heating profiles. Design allows for easily tailored lengths and locations of "hot sections" and larger surface areas for heat radiation.
Hirschberg, M. H.↗
Steady-state heat transfer in transversely heated porous media with application to focused solar energy collectors
A fluid flowing in a porous medium heated transversely to the fluid flow is considered. This configuration is applicable to a focused solar energy collector for use in an electric power generating system. A fluidized bed can be regarded as a porous medium with special properties. The solutions presented are valid for describing the effectiveness of such a fluidized bed for collecting concentrated solar energy to heat the working fluid of a heat engine. Results indicate the advantage of high thermal conductivity in the transverse direction and high operating temperature of the porous medium.
Nichols, L. D.↗
Nozzle flow of laser-heated radiating hydrogen with application to a laser-heated rocket
This paper presents a model for the steady heating of flowing hydrogen by a CW 10.6 micron laser, to consider the feasibility of a laser-heated rocket. The hydrogen flow and the laser beam are parallel, and move into a converging-diverging nozzle. The absorption of laser energy is initiated by a laser-supported combustion wave. The hydrogen is in chemical equilibrium, absorbs laser energy by inverse Bremsstrahlung, and loses energy by radiation. The hydrogen flow was calculated from the rear of the LSC wave to the throat. Estimates of convective heat losses were made using a hydrogen boundary layer analysis. Specific impulse, obtained by expanding isentropically from the throat to 1 atm or a vacuum, varies from 1400 to 3000 s. Radiation losses are 5 to 20%, though the energy fluxes to the walls are quite high. Convective loss estimates are high enough to indicate that coupling to the hot gas flow is required for a 10 kW engine, but not for a 5 MW engine.
Kemp, N. H.↗
System design package: Maxi-therm S-101 heating module, passive heat exchanger
This document is the specification which establishes the requirements for the design, installation, and performance of a passive heat exchanger module with auxiliary heaters for use with solar heating systems. It designates the Interim Performance Criteria applicable to the subsystem and defines any deviations. This document also includes the manufacturing instructions and required materials and parts for the Maxitherm S101 Heating Module.
Source record↗
Prototype solar heating and combined heating and cooling systems
System analysis activities were directed toward refining the heating system parameters. Trade studies were performed to support hardware selections for all systems and for the heating only operational test sites in particular. The heating system qualification tests were supported by predicting qualification test component performance prior to conducting the test.
Source record↗
The effect of external boundary conditions on condensation heat transfer in rotating heat pipes
Experimental evidence shows the importance of external boundary conditions on the overall performance of a rotating heat pipe condenser. Data are presented for the boundary conditions of constant heat flux and constant wall temperature for rotating heat pipes containing either pure vapor or a mixture of vapor and noncondensable gas as working fluid.
Daniels, T. C.↗
Active heat exchange system development for latent heat thermal energy storage
Various active heat exchange concepts were identified from among three generic categories: scrapers, agitators/vibrators and slurries. The more practical ones were given a more detailed technical evaluation and an economic comparison with a passive tube-shell design for a reference application. Two concepts selected for hardware development are a direct contact heat exchanger in which molten salt droplets are injected into a cooler counterflowing stream of liquid metal carrier fluid, and a rotating drum scraper in which molten salt is sprayed onto the circumference of a rotating drum, which contains the fluid heat sink in an internal annulus near the surface. A fixed scraper blade removes the solidified salt from the surface which has been nickel plated to decrease adhesion forces. Suitable phase change material (PCM) storage media with melting points in the temperature range of interest (250 C to 400 C) were investigated. The specific salt recommended for laboratory tests was a chloride eutectic (20.5KCl-24/5 NaCl-55.0MgCl 2% by wt.), with a nominal melting point of 385 C.
Alario, J.↗
Immiscible fluid: Heat of fusion heat storage system
Both heat and mass transfer in direct contact aqueous crystallizing systems were studied as part of a program desig- ned to evaluate the feasibility of direct contact heat transfer in phase change storage using aqueous salt system. Major research areas, discussed include (1) crystal growth velocity study on selected salts; (2) selection of salt solutions; (3) selection of immiscible fluids; (4) studies of heat transfer and system geometry; and (5) system demonstration.
Edie, D. D.↗
Data use investigations for applications Explorer Mission A (Heat Capacity Mapping Mission): HCMM's role in studies of the urban heat island, Great Lakes thermal phenomena and radiometric calibration of satellite data
The utility of data from NASA'a heat capacity mapping mission satellite for studies of the urban heat island, thermal phenomena in large lakes and radiometric calibration of satellite sensors was assessed. The data were found to be of significant value in all cases. Using HCMM data, the existence and microstructure of the heat island can be observed and associated with land cover within the urban complex. The formation and development of the thermal bar in the Great Lakes can be observed and quantitatively mapped using HCMM data. In addition, the thermal patterns observed can be associated with water quality variations observed both from other remote sensing platforms and in situ. The imaging radiometer on-board the HCMM satellite is shown to be calibratible to within about 1.1 C of actual surface temperatures. These findings, as well as the analytical procedures used in studying the HCMM data, are included.
Schott, J. R.↗
Conjugated heat transfer in a laminar boundary layer with heat source at the wall
This work presents the solution of the temperature field in a two-dimensional laminar incompressible flow over a conducting solid plate with a line heat source located at the fluid-solid interface perpendicular to the flow direction. A numerical scheme was used to obtain the temperature profiles as a function of the source strength, and of the properties of the fluid and the solid. The heat conduction and forced convection in the fluid and the heat conduction in the solid were solved for the case of moderate temperature rise, where the assumption of constant properties applies. The model enables the improvement of an instrument for the detection of boundary layer separation. It was found that for the actual parameters of the separation detector, a distance of 4 to 24 mm between the sensors gives an indication of 70 percent of the maximum temperature difference.
Brosh, A.↗