Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “grain orientation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Crystallographic orientation and spatially resolved damage in a dispersion-hardened Al alloy

The in-situ neutron diffraction technique, in combination with both the full-field crystal elasto-viscoplastic finite element model and microstructural characterization, was used to study the deformation-induced damage anisotropy in a commercial Al alloy, subjected to uniaxial tensile and cyclic loading. The simulations capture well the crystallographic-orientation-dependent lattice strain behavior. The hard grains, e.g. those orientated with the <111> and <422> orientations parallel with the uniaxial loading direction (LD), feature large Taylor factors and seem more prone to form damage-related band structures. Their effective elastic moduli decrease with the accumulation of damage, which are different from the soft grains orientated with the <200> orientation along the LD. Correlation between the distribution of voids and that of the residual lattice strain developed after failure may exist. The maximum tensile type residual lattice strain observed after failure may be resulted from the band structure formed in the hardest <111> grains. It was revealed that the band structure triggered by the hard particles could be one of sources of damage. In addition, while the specimen was obviously damaged, a fast stress relief was evidenced after unloading from the tension, especially at the beginning of unloading. Our present investigations provide a novel method for exploring the damage mechanisms of polycrystalline materials during plastic deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Physics-informed machine learning analysis for nanoscale grain mapping by synchrotron Laue microdiffraction

Understanding the grain morphology, orientation distribution and crystal structure of nanocrystals is essential for optimizing the mechanical and physical properties of functional materials. Synchrotron X-ray Laue microdiffraction is a powerful technique for characterizing crystal structures and orientation mapping using focused X-rays. However, when the grain sizes are smaller than the beam size, mixed peaks in the Laue pattern from neighboring grains limit the resolution of grain morphology mapping. We propose a physics-informed machine learning (PIML) approach that combines a convolutional neural network feature extractor with a physics-informed filtering algorithm to overcome the spatial resolution limits of X-rays, achieving nanoscale resolution for grain mapping. Our PIML method successfully resolves the grain size, orientation distribution and morphology of Au nanocrystals through synchrotron microdiffraction scans, showing good agreement with electron backscatter diffraction results. This PIML-assisted synchrotron microdiffraction analysis can be generalized to other diffraction-based probes, enabling the characterization of nanosized structures with micrometre-sized probes.

X-ray crystallography↗
DOE OSTI2023

High-resolution 3D strain and orientation mapping within a grain of a directed energy deposition laser additively manufactured superalloy

The industrialization of Laser Additive Manufacturing (LAM) is challenged by the undesirable microstructures and high residual stresses originating from the fast and complex solidification process. Non-destructive assessment of the mechanical performance controlling deformation patterning is therefore critical. Here, we use Dark Field X-ray Microscopy (DFXM) to map the 3D subsurface intragranular orientation and strain variations throughout a surface-breaking grain within a directed energy deposition nickel superalloy. DFXM results reveal a highly heterogenous 3D microstructure in terms of the local orientation and lattice strain. The grain comprises ≈ 5 μm-sized cells with alternating strain states, as high as 5 x10 -3 , and orientation differences <0.5°. The DFXM results are compared to Electron Backscatter Diffraction measurements of the same grain from its cut-off surface. Here, we discuss the microstructure developments during LAM, rationalising the development of the deformation patterning from the extreme thermal gradients during processing and the susceptibility for solute segregation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Grain Boundary Plane Measurement Using Transmission Electron Microscopy Automated Crystallographic Orientation Mapping for Atom Probe Tomography Specimens

Abstract Grain boundaries are critical in determining the properties of materials, including mechanical stability, conductivity, and corrosion resistance. The specific properties of materials depend not only on the misorientation of the crystals, the three most commonly characterized parameters, but also on the angle of the grain boundary plane between the two crystals, the final two parameters in the five-parameter macroscopic description of the grain boundary. The method presented here allows for the direct measurement of all five parameters of the grain boundary in a transmission electron microscopy specimen of various morphologies. This is especially applicable to atom probe specimens, where only a single-tilt axis is generally available, allowing the crystallographic description to be matched to the detailed chemical data available in the atom probe tomography. This method provides a platform for efficient grain boundary analysis in unique samples, saving operator time and allowing for ease of acquisition and interpretation in comparison with traditional electron diffraction methods.

Materials Science↗
DOE OSTI2021

Simulated effects of sample size and grain neighborhood on the modeling of extreme value fatigue response

Assessing the size of representative volume elements (RVEs) for fatigue-related applications is challenging. A RVE relevant to random microstructure requires a volume of material that is sufficiently large to capture the grain/phase heterogeneity that captures all statistical moments of the distribution of the driving force for fatigue crack formation at “hot spot” grains. Consequently, the large size of a microstructure RVE required to study fatigue phenomena is largely computationally intractable and difficult to explore. A more realistic objective in this work is to systematically study, as a function of the size of a statistical sample of microstructure, trends towards convergence of the simulated distribution of driving force for fatigue crack formation. Our present work accordingly leverages the recently developed open-source PRISMS-Fatigue framework to examine the trends in convergence of extreme value distributions (EVD) of Fatigue Indicator Parameters (FIPs) in progressively larger polycrystalline microstructure realizations of FCC Al alloy 7075-T6 using crystal plasticity finite element method simulations. The results are compared to the traditional method in which ensembles of statistical volume elements (SVEs) are simulated to build up statistics intended to approximate those associated with a larger volume of material. The convergence of EVDs with increase of size of a SVE of microstructure is closely related to the extent of grain nearest neighbor (NN) interactions. Accordingly, the sensitivity of the local micromechanical response at hot spot grains is quantitatively investigated by systematically varying the orientations of NN grains. Results indicate that SVEs with cubic crystallographic texture tend towards convergence of the EVD of FIPs with tens of thousands of grains while the random and rolled textures require larger volumes. Simple relationships based on microstructure parameters (e.g., Schmid Factor, grain size, NN misorientation) do not completely correlate to fatigue hot spot grains. Finally, the sensitivity of the extreme value fatigue response at hot spot grains extends to the 3rd NN when a single neighborhood grain orientation is altered.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Abnormal grain growth in ultrafine grained Ni under high-cycle loading

Abnormal grain growth can occur in polycrystalline materials with only a fraction of grains growing drastically to consume other grains. We report abnormal grain growth in ultrafine grained metal in a rarely explored high-cycle loading regime at ambient temperature. Abnormal grain growth is observed in electroplated Ni microbeams with average initial grain sizes less than 640 nm under a large number of loading cycles (up to 109) with low strain amplitudes (< 0.3%). Such abnormal grain growth occurs predominantly in the family of grains whose <100> orientation is along the tensile/compressive loading direction. Micromechanics analysis suggests that the elastic anisotropy of grains dictates the thermodynamic driving force of abnormal grain growth, such that the lowest strain energy density of the <100> oriented grain family dominates grain growth. This work unveils a unique type of abnormal grain growth that may be harnessed to tailor grain microstructures in materials.

36 MATERIALS SCIENCE↗
NASA NTRS1980

Creep and stress rupture of oxide dispersion strengthened mechanically alloyed Inconel alloy MA 754

The creep and stress rupture behavior of the mechanically alloyed oxide dispersion strengthened nickel-base alloy MA 754 was studied at 760, 982 and 1093 C. Tensile specimens with a fine, highly elongated grain structure, oriented parallel and perpendicular to the longitudinal grain direction were tested at various stresses in air under constant load. It was found that the apparent stress dependence was large, with power law exponents ranging from 19 to 33 over the temperature range studied. The creep activation energy, after correction for the temperature dependence of the elastic modulus, was close to but slightly larger than the activation energy for self diffusion. Rupture was intergranular and the rupture ductility as measured by percentage elongation was generally low, with values ranging from 0.5 to 16 pct. The creep properties are rationalized by describing the creep rates in terms of an effective stress which is the applied stress minus a resisting stress consistent with the alloy microstructure. Values of the resisting stress obtained through a curve fitting procedure are found to be close to the values of the particle by-pass stress for this oxide dispersion strengthened alloy, as calculated from the measured oxide particle distribution.

Howson, T. E.↗
DOE OSTI2020

Anisotropic Motions of Fibrils Dictated by Their Orientations in the Lamella: A Coarse-Grained Model of a Plant Cell Wall

Plant cell walls are complex systems that exhibit the characteristics of both rigid and soft material depending on their external perturbations. The three main polymeric components in a plant primary cell wall are cellulose fibrils, hemicellulose, and pectins. These components interact in a hierarchical fashion giving rise to mesoscale structural features such as cellulose bundles, lamella stacking, and so on. Although several studies have focused on understanding these unique structural features, a clear picture linking them to cell wall mechanics is still lacking. As a first step toward this goal, a phenomenological model of plant cell wall has been developed in this work by using available experimental data to investigate the underlying connections between mesoscale structural features and the motions of fibrils during deformation. In this model cellulose fibrils exhibit motions such as angular reorientations and kinking upon forced stretching. Furthermore, these motions are dependent on the orientation of fibrils with respect to the stretch direction, i.e., fibrils that are at an angle to the stretch direction exhibit predominant angular reorientations, while fibrils transverse to the stretch direction undergo kinking as a result of transverse compression. Varying the chain length of pectin had negligible effects on these motions. One of the main contributions from this work is the development of a simple model that can be easily fine-tuned to test other hypotheses and extended to include additional experimental knowledge about the structural aspects of cell walls in the future.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of loading path on grain misorientation and geometrically necessary dislocation density in polycrystalline aluminum under reciprocating shear

Solid phase processing (SPP) is a promising alloy fabrication technique to produce fine and homogeneous grain structures for high-performance alloys. However, there is very limited modeling capability to understand and predict the grain refinement during SPP. In this work, the crystal plasticity theory was used to study elastic-plastic deformation in polycrystalline aluminums under large shear deformation. Two approaches, kernel averaged misorientation (KAM) and grain reference orientation deviation (GROD), were used to assess the grain misorientations. The geometrically necessary dislocation (GND) density was computed with the plastic strain rate. The deformation simulations were carried out under two loading conditions to investigate the effect of loading paths on the evolutions of grain misorientation and GND density. The results show that the regions with high misorientation and GND density first appear near grain boundaries. These regions then extend toward interior grains. The loading path affects dislocation system activation and dislocation recovery, hence dislocation evolution and misorientation. In conclusion, both two- and three-dimensional simulations showed that the spatial and temporal evolutions of GROD, KAM, and GND density in are closely correlated, which indicates they all can be used as criteria of grain refinement or recrystallization.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Evaluating the Taylor hardening model in polycrystalline Ti using high energy X-ray diffraction microscopy

High energy X-ray diffraction microscopy (HEDM) was employed to index nearly 1000 grains in a polycrystalline Ti specimen and characterize their deformation during an incremental tensile test. For each grain, the positions of its associated diffraction peaks were used for analyzing its evolving crystal orientation and stress tensor. The azimuthal breadth of each peak at different load steps was measured, allowing measurement of initial yielding and providing an estimate of the dislocation density evolution in each grain. Furthermore, the Taylor hardening model was evaluated grain by grain using the above data, indicating that it can represent hardening in most grains. The yield stress and the strain hardening coefficient for all grains were statistically analyzed with respect to grain orientation, grain size, slip systems, and the surrounding neighborhood to examine how the yield stress and hardening are correlated.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Graph neural networks for efficient learning of mechanical properties of polycrystals

Herein we present graph neural networks (GNNs) as an efficient and accurate machine learning approach to predict mechanical properties of polycrystalline materials. Here, a GNN was developed based on graph representation of polycrystals incorporating only fundamental features of grains including their crystallographic orientation, size, and grain neighbor connectivity information. We tested our method on modeling stiffness and yield strength of α -Ti microstructures, varying in their crystallographic texture. We find the GNN predicts both properties with high accuracy with mean relative errors of ~1% for unseen microstructures from a given set of textures and < 2% for microstructures of unseen texture, even when presented with limited training data. This accuracy is comparable to methods that require high-resolution three-dimensional (3D) microstructure data, such as 3D convolutional neural networks (3D-CNNs) and models that depend on the computation of spatial statistics. The present results show that graph-based deep learning is a promising framework for property prediction, especially considering the high cost associated with obtaining high-resolution 3D microstructure data and the general scarcity of experimental materials datasets.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Nanoscale chemistry and ion segregation in zirconia-based ceramic at grain boundaries by atom probe tomography

In this work nanoscale features that are of importance in the stability of yttria-stabilized tetragonal zirconia (Y-TZP) are quantified through atom probe tomography. In-depth analysis of grain boundary chemistry revealed preferential segregation of lighter and smaller ions towards specific grain boundaries. The relationship between elemental segregation and the local atomistic structure is investigated at the sub-nanometer level to gain insights on nanoscale features associated with the tetragonal-monoclinic phase transformation in Y-TZP through grain boundary characterization. Furthermore, principal component analysis was implemented to reveal any potential biases from varied field evaporation across stabilizer-rich grain boundaries. The observed variations in ion density across different grains suggested a variation in field which was attributed to potential variations in grain crystal orientation. In order to reveal the subtle depletion of oxygen atoms within grain boundaries a new methodology to map oxygen vacancies is proposed, utilizing the relative neighborhood chemistry of individual yttrium atoms.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Helium effects on the surface and subsurface evolutions in single-crystalline tungsten

Tungsten (W) has been perceived as one of the most promising plasma facing materials (PFMs) for future fusion reactors. In the past decade, its behavior under irradiation and helium (He) plasma interaction has been extensively studied. However, some key knowledge gaps still exist, such as the influence of crystallographic orientation on the surface and subsurface evolutions. In this work, we focus on the He ion-beam irradiation damage effects in mirror-polished single-crystalline W samples with three different surface planes of {100}, {110} and {111}. Irradiation was performed at room temperature using 40 keV He+ to a fluence of 1 × 10 16 /cm 2 , followed by thermal desorption spectroscopy (TDS) up to ~1920 K. The microstructures of He-irradiated W before and after TDS heat treatment were characterized by scanning and transmission electron microscopy. Subsurface He bubbles were imaged in all irradiated samples, but newly formed <111>-oriented surface grains and surface blisters were only observed in W {100} and {110} starting orientations. These results reveal that radiation damage, He thermal desorption, and surface/subsurface evolution are all strongly dependent on crystallographic orientation. Underlying physical mechanisms are discussed based on ion channeling effects, He-vacancy interactions, and surface diffusion. In conclusion, these findings provide new insights into He effects in W.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Processing Effects on the Self-Assembly of Brush Block Polymer Photonic Crystals

Here,the self-assembly of poly(dimethylsiloxane)-b-poly(trimethylene carbonate) (PDMS-b-PTMC) bottlebrush block polymers was investigated under different processing conditions. Small-angle X-ray scattering (SAXS) and UV/Visible spectroscopy provided insight into the self-assembly and structure in response to heating and applied pressure. In the absence of applied pressure (i.e., before annealing), the PDMS-b-PTMC bottlebrush block polymers are white solids and adopt small, randomly oriented lamellar grains. Heating the materials to 140 °C in the absence of applied pressure appears to “lock in” the isotropic, short-range-ordered state, preventing the formation of the long-range-ordered lamellar structure responsible for photonic properties. Applying modest anisotropic pressure (3 psi) between parallel plates at ambient temperature orients the short-range lamellar grains; however, applied pressure alone does not produce long-range order. Only when the bottlebrush block polymers were heated (>100 °C) under modest pressure (3 psi) were long-range-ordered photonic crystals formed. Analysis of the SAXS data motivated analogies to liquid crystals and revealed the potential self-assembly pathway. These results provide insight into the structure and self-assembly of bottlebrush block polymers with low glass transition temperature side chains in response to different processing conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

A Technique for the Quantitative Characterization of Weld Microstructure and Application to Mo Welds

The choice of weld parameters determines the size, shape, and curvature of grains in the fusion zone (FZ) and heat-affected zone (HAZ) of welds while the mechanical properties of the welds are correlated to this microstructure. Here, a new technique to quantitatively evaluate these microstructural characteristics in both zones of welds has been applied to molybdenum gas tungsten arc welds fabricated using different weld parameters. Trends in microstructural characteristics in the FZ and HAZ were evaluated and correlated with changes to heat input, weld speed, and weld technique. The use of this approach showed that a 20 pct decrease in heat input caused a 20 pct decrease in the number of FZ grains with aspect ratios ≥ 4. The orientations of the FZ grain segments as a function of distance from the FZ centerline were significantly affected by the weld speed and its effect on weld pool shape. A 50 pct increase in weld speed caused a 20 pct decrease in grain segments orientated 60 to 90 deg from the normal to the direction of welding. This technique also captured differences in grain sizes and grain size anisotropy in the FZ between welds made with a constant current, pulsed current, and use of a 4-pole-magnetic oscillator.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Plasma-Assisted Epitaxy of Piezoelectric Sc x Al 1-x N Films on Sapphire for Use in Harsh-Environment Microwave Acoustic Sensors

The Sc x Al 1-x N wurtzite structure has been shown theoretically and experimentally to exhibit significantly higher piezoelectric coupling compared to pure AlN. In this work, a plasma-assisted epitaxial growth method has been used to synthesize epitaxial (0002) Sc x Al 1-x N films on c-sapphire substrates from x = 0.07 to 0.30 by co-evaporating high-purity Sc and Al sources in the presence of a nitrogen plasma generated by an RF plasma source. Epitaxial Sc x Al 1-x N films with highly oriented (0002) grains and in-plane registry were produced on c-sapphire substrates that were pre-exposed to the nitrogen plasma to form an oxynitride seed layer. Growth of Sc x Al 1-x N films was carried out at 930°C under both metal-rich and N-rich conditions using precisely controlled Sc, Al, and N-plasma fluxes. Metal-rich depositions yielded non-(0002)-oriented Sc x Al 1-x N grains and intermetallic ScAl grains. Nitrogen-rich growth with a Sc/Al flux ratio of 1/3 produced the best (0002) epitaxy as determined by x-ray diffraction analysis. Surface acoustic wave resonator (SAWR) devices were fabricated from 500-nm-thick Sc x Al 1-x N and AlN films to extract their electromechanical coupling coefficients, k 2 . As the Sc concentration in the films increases, the degree of (0002) epitaxy is reduced, yet the value of k 2 increases becasue there is more Sc in the wurzite lattice despite the decreased level of (0002) grain alignment. As a result, the use of a 10-nm-thick Si x N y capping layer on top of the Sc x Al 1-x N films aids in preventing etching during SAWR device photolithography and also helps hinder film oxidation up to 800°C.

36 MATERIALS SCIENCE↗
DOE OSTI2020

XtalCAMP: a comprehensive program for the analysis and visualization of scanning Laue X-ray micro-/nanodiffraction data

XtalCAMP is a software package based on the MATLAB platform, which is suitable for, but not limited to, the analysis and visualization of scanning Laue X-ray micro-/nanodiffraction data. The main objective of the software is to provide complementary functionalities to the Laue indexing software packages used at several synchrotron beamlines. Here, the graphical user interfaces allow the easy analysis of characteristic microstructure features, including real-time intensity mapping for a quick examination of phase, grain and defect distribution, 2D color-coded mapping of microstructural properties from the output of other Laue indexing software, crystal orientation visualization, grain boundary characterization based on orientation/misorientation calculation, principal strain/stress analysis, and strain ellipsoid representation, as well as a series of additional toolkits. As an example, XtalCAMP is applied to the microstructural investigation of a solution-heat-treated Ni-based superalloy manufactured using a laser 3D-printing technique, and a deformed natural quartzite from Val Bregaglia in the Central Alps.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Local residual stresses and microstructure within recrystallizing grains in iron

The intragranular strains and the microstructure within recrystallizing grains in single phase pure iron have been systematically studied in 3D using synchrotron micro-diffraction. In contradiction to common knowledge we observe that residual elastic strains of up to 1–2 × 10 –3 are present in the recrystallizing grains. The local strain variations within individual grains can be similar in magnitude to those between different grains. The effects of processing parameters, including rolling reduction, recrystallized volume fraction, and cooling rate, as well as microstructural parameters, including grain size, orientation and internal misorientation, on the development of local residual elastic strains and microstructure have been quantified. It is suggested that the difference in local defect density between recrystallized grains and the surrounding deformed matrix, as well as the redistribution of medium to long-range residual stresses in the deformed grains, are the main reasons for the development of such strains in the recrystallized grains. The local residual stress levels are calculated and their possible impact on the mechanical properties and recrystallization processes are discussed.

36 MATERIALS SCIENCE↗