SEARCH · Engineering Papers

Results for “glycolization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Investigation of Thermolytic Hydrogen Generation Rate in Tank 44 Dissolved Saltcake Samples

Saltcake core samples collected from Tank 44 in 2006 were dissolved to provide material for HGR measurements applicable to F-Area dissolved saltcake material. Additionally, characterization was performed on the Tank 44 saltcake material. The following are key results from the Tank 44 saltcake characterization. The Tank 44 Upper Saltcake Composite, corresponding to the 171 to 285 inch tank level, contained by mass approximately 69% sodium nitrate, 11% sodium carbonate, 8% sodium nitrite, smaller amounts of other salts and components, and 9% unquantified (which includes water, water of hydration, oxygen/hydrogen content of oxides and hydroxides, and uncertainty). The Tank 44 Lower Saltcake Composite, corresponding to the 76 to 114 inch tank level, contained by mass approximately 49% sodium carbonate, 18% sodium nitrate, smaller amounts of other salts, at least 8% sludge, and 9% unquantified (see above). The dissolved saltcake contained free hydroxide less than quantifiable (<0.01 M) due to the limited quantity of material that could be removed from the Shielded Cells based on the sample radioactivity. Measurement by pH paper provided an approximate pH of 12. The following are key results from the Tank 44 HGR testing. During boiling at 106.7 °C, HGR for Tank 44 dissolved saltcake without added glycolate was 7.2×10 -8 ft 3 h -1 ga l-1 . During boiling at 106.9 °C, HGR for Tank 44 dissolved saltcake with 1000 mg/L of added glycolate was 8.2×10 -8 ft 3 h -1 gal -1 . ∙ For the test without added glycolate, the first several HGR measurements at 70, 85, and 100 °C gave indication of the release of dissolved hydrogen and should not be used to represent the sustained thermolytic HGR for those temperatures. The measurements at boiling are the best representation of thermolysis in this testing. Carbon dioxide was observed at concentrations up to 6 vol% in the flow-system offgas for the test at boiling. ∙ Methane generation was observed at 100 °C and boiling. Methane concentration in the total gas generated during testing remained well below the lower flammability limit for methane in air. The addition of 1000 mg/L of glycolate did not have a significant impact on the hydrogen generation rates measured during this testing. The low hydroxide concentration in the Tank 44 dissolved saltcake likely influenced the relatively low thermolytic HGR and high carbon dioxide release observations in this testing. Based on the observation that methane was generated or released upon heating SRS radioactive Tank 44 waste samples to 100 °C and above, we recommend gaining a greater understanding of the cause and mechanism of its generation. First, the applicable literature should be reviewed to reveal the thermolytic methane generation mechanisms of possible methane generating species in the SRS CSTF. If warranted, a plan should be developed for simulant tests with methylated siloxanes and other applicable compounds in order to gain a better mechanistic understanding of methane generation in the SRS CSTF.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

Impacts of the Addition of Sodium Reactor Experiment (SRE) and DR-3 Fuel from H-Canyon to Tank 40 on Acid Stoichiometry and Hydrogen Production

H-Canyon plans to discard Sodium Reactor Experiment (SRE) material that is currently stored in Tanks 16.3 and 16.4. Savannah River Remediation (SRR) determined that a portion of the SRE material can be added to Sludge Batch 9 (SB9) in Tank 40 and the remainder will be added to Sludge Batch 10 (SB10) that is currently being prepared in Tank 51. A processing flowsheet for both the nitric-formic acid flowsheet and the nitric-glycolic acid flowsheet were previously developed for SB9 sludge-only and coupled operation with the Actinide Removal Process – Modular Caustic Side Solvent Extraction Unit (ARP-MCU) and the Salt Waste Processing Facility (SWPF). Due to the compositional change in Tank 40 after the addition of SRE material, it is necessary to determine the influence on the acid stoichiometry operating window and hydrogen production for SB9 processing. An assessment was completed to address the influence of an addition of SRE and DR-3 Fuel from H-Canyon on the chemistry of Tank 40, the defined acid stoichiometry window (with and without SWPF streams) for the nitric-formic and nitric-glycolic acid flowsheets, and the resulting influence of the hydrogen production. Hydrogen production during the SRAT/SME cycles consists of thermolytic, radiolytic, and catalytic hydrogen. For the nitric-formic acid flowsheet, catalytic hydrogen dominates the hydrogen production during DWPF operation mode for the SRAT and SME vessels. This report was written to summarize that assessment. No SRNL testing is needed prior to adding up to 7,100 additional gallons of SRE and DR-3 Fuel from H-Canyon to Tank 40. Also, the addition of SRE will not exceed the Shielded Cells reported values for catalytic hydrogen for either the nitric-formic acid flowsheet (Technical Safety Requirement (TSR) limit of 0.15 lb/h) or the nitric-glycolic acid flowsheet (TSR limit 0.024 lb/h). The addition of the ARP stream from SWPF and the use of the nitric-glycolic acid flowsheet are both expected to decrease hydrogen generation, leading to a larger safety margin in the CPC.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2021

Investigation of Thermolytic Hydrogen Generation Rate in Tank 44 Dissolved Saltcake Samples

Saltcake core samples collected from Tank 44 in 2006 were dissolved to provide material for HGR measurements applicable to F-Area dissolved saltcake material. Additionally, characterization was performed on the Tank 44 saltcake material. The following are key results from the Tank 44 saltcake characterization. The Tank 44 Upper Saltcake Composite, corresponding to the 171 to 285 inch tank level, contained by mass approximately 69% sodium nitrate, 11% sodium carbonate, 8% sodium nitrite, smaller amounts of other salts and components, and 9% unquantified (which includes water, water of hydration, oxygen/hydrogen content of oxides and hydroxides, and uncertainty). The Tank 44 Lower Saltcake Composite, corresponding to the 76 to 114 inch tank level, contained by mass approximately 49% sodium carbonate, 18% sodium nitrate, smaller amounts of other salts, at least 8% sludge, and 9% unquantified (see above). The dissolved saltcake contained free hydroxide less than quantifiable (<0.01 M) due to the limited quantity of material that could be removed from the Shielded Cells based on the sample radioactivity. Measurement by pH paper provided an approximate pH of 12. The following are key results from the Tank 44 HGR testing. During boiling at 106.7 °C, HGR for Tank 44 dissolved saltcake without added glycolate was 7.2×10 -8 ft 3 h -1 gal -1 . During boiling at 106.9 °C, HGR for Tank 44 dissolved saltcake with 1000 mg/L of added glycolate was 8.2×10 -8 ft 3 h -1 gal -1 . For the test without added glycolate, the first several HGR measurements at 70, 85, and 100 °C gave indication of the release of dissolved hydrogen and should not be used to represent the sustained thermolytic HGR for those temperatures. The measurements at boiling are the best representation of thermolysis in this testing. Carbon dioxide was observed at concentrations up to 6 vol% in the flow-system offgas for the test at boiling. Methane generation was observed at 100 °C and boiling. Methane concentration in the total gas generated during testing remained well below the lower flammability limit for methane in air. The addition of 1000 mg/L of glycolate did not have a significant impact on the hydrogen generation rates measured during this testing. The low hydroxide concentration in the Tank 44 dissolved saltcake likely influenced the relatively low thermolytic HGR and high carbon dioxide release observations in this testing. Based on the observation that methane was generated or released upon heating SRS radioactive Tank 44 waste samples to 100 °C and above, we recommend gaining a greater understanding of the cause and mechanism of its generation. First, the applicable literature should be reviewed to reveal the thermolytic methane generation mechanisms of possible methane generating species in the SRS CSTF. If warranted, a plan should be developed for simulant tests with methylated siloxanes and other applicable compounds in order to gain a better mechanistic understanding of methane generation in the SRS CSTF.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

NASA NTRS1984

Experimental and analytical investigation of a freezing point depressant fluid ice protection system

A glycol-exuding porous leading edge ice protection system was tested in the NASA Icing Research Tunnel. Stainless steel mesh, laser drilled titanium, and composite panels were tested on two general aviation wing sections. Two different glycol-water solutions were evaluated. Minimum glycol flow rates required for anti-icing were obtained as a function of angle of attack, liquid water content, volume median drop diameter, temperature, and velocity. Ice accretions formed after five minutes of icing were shed in three minutes or less using a glycol fluid flow equal to the anti-ice flow rate. Two methods of predicting anti-ice flow rates are presented and compared with a large experimental data base of anti-ice flow rates over a wide range of icing conditions. The first method presented in the ADS-4 document typically predicts flow rates lower than the experimental flow rates. The second method, originally published in 1983, typically predicts flow rates up to 25 percent higher than the experimental flow rates. This method proved to be more consistent between wing-panel configurations. Significant correlation coefficients between the predicted flow rates and the experimental flow rates ranged from .867 to .947.

Albright, A. E.↗

NASA NTRS1987

Prebiotic synthesis of imidazole-4-acetaldehyde and histidine

The prebiotic synthesis of imidazole-4-acetaldehyde and imidazole-4-glycol from erythrose and formamidine has been demonstrated as well as the prebiotic synthesis of imidazole-4-ethanol and imidazole-4-glycol from erythrose, formaldehyde, and ammonia. The maximum yields of imidazole-4-acetaldehyde, imidazole-4-ethanol, and imidazole-4-glycol obtained in these reactions are 1.6, 5.4, and 6.8 percent respectively, based on the erythrose. Imidazole-4-acetaldehyde would have been converted to histidine on the primitive earth by a Strecker synthesis, and several prebiotic reactions would convert imidazole-4-glycol and imidazole-4-ethanol to imidazole-4-acetaldehyde.

Shen, Chun↗

DOE OSTI2020

High voltage window electrolyte for supercapacitors

A supercapacitor according to the present invention includes a negative carbon-comprising electrode which does not intercalate sodium, and a positive carbon-comprising electrode. An electrolyte composition comprises sodium hexafluorophosphate and a non-aqueous solvent comprising at least one selected from the group consisting of ethylene glycol dimethyl ether, diethylene glycol dimethyl ether, triethylene glycol dimethyl ether, and tetraethylene glycol dimethyl ether. The supercapacitor has an electrochemical voltage window of from +0.0 V to 3.5 V (full cell voltage). The electrolyte has an electrochemical voltage window of from +0.05 V to 3.9 V vs. Na/Na+. A method of making and a method of operating a supercapacitor is also disclosed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

High voltage window electrolyte for supercapacitors

25 ENERGY STORAGE↗

DOE OSTI2021

Low-temperature (< 200 °C) degradation of electronic nicotine delivery system liquids generates toxic aldehydes

Electronic cigarette usage has spiked in popularity over recent years. The enhanced prevalence has consequently resulted in new health concerns associated with the use of these devices. Degradation of the liquids used in vaping have been identified as a concern due to the presence of toxic compounds such as aldehydes in the aerosols. Typically, such thermochemical conversions are reported to occur between 300 and 400 °C. Herein, the low-temperature thermal degradation of propylene glycol and glycerol constituents of e-cigarette vapors are explored for the first time by natural abundance 13 C NMR and 1 H NMR, enabling in situ detection of intact molecules from decomposition. The results demonstrate that the degradation of electronic nicotine delivery system (ENDS) liquids is strongly reliant upon the oxygen availability, both in the presence and absence of a material surface. When oxygen is available, propylene glycol and glycerol readily decompose at temperatures between 133 and 175 °C over an extended time period. Among the generated chemical species, formic and acrylic acids are observed which can negatively affect the kidneys and lungs of those who inhale the toxin during ENDS vapor inhalation. Further, the formation of hemi- and formal acetals is noted from both glycerol and propylene glycol, signifying the generation of both formaldehyde and acetaldehyde, highly toxic compounds, which, as a biocide, can lead to numerous health ailments. The results also reveal a retardation in decomposition rate when material surfaces are prevalent with no directly observed unique surface spectator or intermediate species as well as potentially slower conversions in mixtures of the two components. The generation of toxic species in ENDS liquids at low temperatures highlights the dangers of low-temperature ENDS use.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

In-Process Melt Separation of Depolymerized PET in PET/PE Blends for Upcycling via Twin-Screw Extrusion

Our previous work focused on depolymerizing polyethylene terephthalate (PET) in twin-screw extrusion, as part of a broader project to continuously separate PET from polyolefins in the melt. This study focused on linear low-density polyethylene (LLDPE) and PET films and the use of ethylene glycol (EG), diethylene glycol (DEG), triethylene glycol (TEG), and bis(2-hydroxyethyl) terephthalate (BHET) to depolymerize the PET in the extruder to levels above 90% Mw. In this work, the focus will shift to achieving separation of the two polymers in the twin-screw extruder, which is made possible due to a 90% reduction in the Mw of the PET, which caused a decrease of its viscosity by several orders of magnitude. Owing to the viscosity difference and pressure buildup in the die, the low-viscosity PET preferentially exited a degassing vent instead of going through the die. This is because the flow of the PET would travel through a non-pressure vent rather than through a high-pressure die. However, owing to the higher viscosity of the LLDPE, the pressure was too high to pass through such a small diameter vent hole. Supercritical CO 2 (SCCO 2 ) was used to assist in this extraction, but SCCO 2 negatively impacted the overall degree of separation. Through analysis of the separated materials, it was concluded that a high separation of the two materials was achieved. TGA and FTIR confirmed that the material separated from the vent was 100% PET. The material removed from the die was composed of 95% LLDPE and 5% PET.

36 MATERIALS SCIENCE↗

DOE OSTI2026

In‐Process Melt Separation of PE/PET Blends for Upcycling via Twin‐Screw Extrusion. Impact of Catalyst Reagents on PET Depolymerization

Part 1 of this work focused on depolymerizing polyethylene terephthalate (PET) in twin-screw extrusion, as part of a broader project to continuously separate PET from polyolefins in the melt. This study focused on linear low-density polyethylene (LLDPE) and PET films and the use of ethylene glycol (EG), diethylene glycol (DEG), triethylene glycol (TEG), and bis(2-hydroxyethyl) terephthalate (BHET) to depolymerize the PET in the extruder to levels above 90% Mw. In part 2, the focus will shift to achieving separation of the two polymers in the twin-screw extruder, which is made possible due to a 90% reduction in the Mw of the PET, which caused a decrease of its viscosity by several orders of magnitude. Owing to the viscosity difference and pressure buildup in the die, the low-viscosity PET preferentially exited a degassing vent instead of going through the die. This is because the flow of the PET would travel through a non-pressure vent rather than through a high-pressure die. However, owing to the higher viscosity of the LLDPE, the pressure was too high to pass through such a small diameter vent hole. Supercritical CO₂ (SCCO₂) was used to assist in this extraction, but SCCO₂ negatively impacted the overall degree of separation. Through analysis of the separated materials, it was concluded that a very high separation of the two materials was achieved. TGA and FTIR confirmed that the material separated from the vent was 100% PET. The material removed from the die was composed of 90% LLDPE and 10% PET.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Catalase protects against nonenzymatic decarboxylations during photorespiration in Arabidopsis thaliana

Abstract Photorespiration recovers carbon that would be otherwise lost following the oxygenation reaction of rubisco and production of glycolate. Photorespiration is essential in plants and recycles glycolate into usable metabolic products through reactions spanning the chloroplast, mitochondrion, and peroxisome. Catalase in peroxisomes plays an important role in this process by disproportionating H 2 O 2 resulting from glycolate oxidation into O 2 and water. We hypothesize that catalase in the peroxisome also protects against nonenzymatic decarboxylations between hydrogen peroxide and photorespiratory intermediates (glyoxylate and/or hydroxypyruvate). We test this hypothesis by detailed gas exchange and biochemical analysis of Arabidopsis thaliana mutants lacking peroxisomal catalase. Our results strongly support this hypothesis, with catalase mutants showing gas exchange evidence for an increased stoichiometry of CO 2 release from photorespiration, specifically an increase in the CO 2 compensation point, a photorespiratory‐dependent decrease in the quantum efficiency of CO 2 assimilation, increase in the 12 CO 2 released in a 13 CO 2 background, and an increase in the postillumination CO 2 burst. Further metabolic evidence suggests this excess CO 2 release occurred via the nonenzymatic decarboxylation of hydroxypyruvate. Specifically, the catalase mutant showed an accumulation of photorespiratory intermediates during a transient increase in rubisco oxygenation consistent with this hypothesis. Additionally, end products of alternative hypotheses explaining this excess release were similar between wild type and catalase mutants. Furthermore, the calculated rate of hydroxypyruvate decarboxylation in catalase mutant is much higher than that of glyoxylate decarboxylation. This work provides evidence that these nonenzymatic decarboxylation reactions, predominately hydroxypyruvate decarboxylation, can occur in vivo when photorespiratory metabolism is genetically disrupted.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2025

Tunable Crosslinked Ether Polymer Network Electrolytes for High‐Performance All‐Solid‐State Sodium Batteries

All-solid-state batteries (ASSBs) are critical for achieving high energy density and enhanced safety. Solid polymer electrolytes (SPEs) offer key advantages over other electrolytes, including improved safety, flexibility, and interfacial contact. Among the SPEs, ether-based polymers are widely studied due to their ease of processing and high ionic conductivity (σi) in the amorphous state. In this work, the introduction of poly(ethylene glycol) methyl ether methacrylate (PEGMEMA) into an SPE matrix composed of poly(ethylene glycol) diacrylate (PEGDA), poly(ethylene glycol) (PEG2k), and sodium bis(fluorosulfonyl)imide (NaFSI) salt is investigated to facilitate the formation of amorphous, high σ i SPEs through end-group engineering and polymer ratio optimization. PEGMEMA enhances structural integrity via crosslinking with PEGDA through its methacrylate group, while its methyl end group aids ion conduction. A 2:1:7 ratio of PEGDA:PEGMEMA:PEG2k exhibits a σi of 1.16 x 10 -4 S cm -1 and oxidative stability up to 4.4 V at 60 °C. A solid-state cell incorporating this SPE, a Na 2/3 Ni 1/3 Mn 2/3 O 2 (NM12) cathode, and a sodium-metal anode demonstrates excellent cycling stability, retaining over 80 % of its initial capacity for 150 cycles at 60 °C. The findings highlight the potential of end-group engineering in improving the electrochemical performance of SPEs.

25 ENERGY STORAGE↗

DOE OSTI2020

Goldilocks and the three glymes: How Na+ solvation controls Na–O 2 battery cycling

In this work we report a framework to understand the role of solvent-salt interactions and how they mediate the performance of sodium-air/O 2 batteries. The utilization of suitable electrolyte materials remains a point of major concern within the research community, as their stability and decomposition pathways during cycling are intimately connected with capacity and cycle life. Glyme based solvents have been widely utilized in Na–O 2 batteries, however, to date no clear correlation between solvent/electrolyte properties and battery performance has been given. Herein, we have examined the effect of glyme chain length (ethylene glycol dimethyl ether DME; diethylene glycol dimethyl ether, DEGDME; and tetraethylene glycol dimethyl ether, TEGME) on the cycling behaviour of Na–O 2 batteries and conclude that overall cell performance is highly dependent on solvent selection, salt concentration and rate of discharge/charge. We demonstrate how solvent selection helps define cell chemistry and performance by linking salt-solvent interactions to enthalpy of dissolution - and subsequently to sodium battery electrolyte properties - through the combination of both experimental and theoretical methodologies. The approaches detailed in this study could be used to predictively prepare electrolytes for Li-air batteries, other glyme-based electrochemical systems and low temperature applications.

25 ENERGY STORAGE↗

DOE OSTI2026

The effect of hydroxyl spacing in diols on the solvation structure, dynamics, and transport properties of choline chloride-based deep eutectic solvents

Deep eutectic solvents (DESs) are a class of liquids that offer great potential in alleviating some of the challenges present in today's long-term energy storage methods because they have physical properties that are favorable for storable electrolyte solutions. In this work, a series of glycols (ethylene glycol, 1,3-propanediol, 1,4-butanediol, and 1,5-pentanediol) were studied as potential hydrogen bond donors (HBD) with a common choline chloride (ChCl) as the hydrogen bond acceptor (HBA). The solvation dynamics of the prepared systems were studied by measuring the solvent reorganization response using femtosecond transient absorption spectroscopy (fs-TA). Conductivity, viscosity, density, ET(30) polarity, and dynamics of the prepared DESs were analyzed, with a particular interest in determining the effect of HBD chain length on these parameters. Here, classical molecular dynamics simulations were employed to investigate how the local liquid structure, solvent dynamics, and bulk solvent properties vary with changes in glycol chain length.

Conductivity↗

DOE OSTI2025

Understanding the impact of SPMAK and PEGPEA in crosslinked PEGDA membranes: Methanol-carboxylate co-transport behavior and correlating structure-physicochemical-transport properties

Investigating multicomponent transport in dense, hydrated polymer membranes is necessary in applications such as fuel cells, electrolyzers, and desalination systems. Of particular interest are photoelectrochemical CO 2 reduction cells (PEC-CRC) which produce liquid products such as alcohols (methanol) and carboxylates (formate, acetate). Flux coupling and competitive sorption behavior of these products (solutes) have been found to affect permselectivity, thereby motivating us to investigate fundamental membrane structure-physicochemical-transport relationships. Past research has shown that systematic tuning of crosslinked cation exchange membranes (CEMs) with charge-neutral monoacrylate monomers containing alkyl and phenyl groups (i.e., poly(ethylene glycol) methacrylate (PEGMA), and poly(ethylene glycol) phenyl ether acrylate (PEGPEA)) can suppress acetate transport (permeability) in co-permeation with methanol. To further investigate this transport behavior and to enhance membrane ionic conductivities, 3-sulfopropyl methacrylate potassium (SPMAK), a sulfonated monoacrylate monomer is incorporated here. SPMAK content is varied with neutral PEGPEA and diacrylate crosslinker, poly (ethylene glycol) diacrylate (PEGDA) of two different chain lengths (n = 10 and 13) to prepare membranes of various compositions. Electrochemical and physicochemical properties including ionic conductivity, ion exchange capacity, and water uptake increase with increasing charged SPMAK content. Different states of water within hydrated membranes are probed using differential scanning calorimetry (DSC), where increasing intermediate (loosely bound) water is observed with increasing hydrophilic SPMAK content. The transport behavior of methanol and carboxylates (formate, acetate, propionate) are investigated, where permeabilities vary as methanol > formate > acetate ≈ propionate. Interestingly, permeabilities decrease with increasing PEGPEA content and are more dependent on solute diffusion than sorption. Permeabilities and diffusivities decrease while permselectivities increase with decreasing PEGDA chain length.

25 ENERGY STORAGE↗

DOE OSTI2024

Sub-Ambient Performance of Potassium Sarcosinate for Direct Air Capture Applications: CO 2 Flux and Viscosity Measurements

Absorption based direct air capture (DAC) technologies have garnered significant interest in recent years due to their scalability, competitive regeneration energy requirements, and low susceptibility to degradation. One of the key advantages of DAC lies in its flexible siting options and the potential to utilize low-value land. However, most of the research in this field has been focused on ambient climate zones (T > 20 °C), overlooking sub-ambient (–30 °C < T < 20 °C) regions, which comprise approximately 70 % of the Earth’s surface. To fully realize the potential of DAC, it is essential to understand how DAC solvents perform in these sub-ambient conditions before any large-scale deployment can be considered. Among DAC solvents of interest, potassium sarcosinate (K-SAR) has emerged as a promising candidate due to its high CO 2 capacity, fast uptake kinetics, compatibility with contactor packing materials, low volatility, good thermal and oxidative stability, and competitive regeneration energy requirements compared to current industry standards. This paper characterizes the CO 2 flux and viscosity of K-SAR at sub-ambient conditions and explores the potential of using ethylene glycol and triethylene glycol as additives to prevent solvent freezing in DAC applications. For 1 M K-SAR, the CO 2 flux ranges between 1.3 × 10 -5 and 8.0 × 10 -5 mol m –2 s –1 across a temperature range of –5 °C to 45 °C. Ethylene glycol is shown to effectively suppress the freezing point of K-SAR below –30 °C with volumetric loadings of the additive as low as 0.1. Here, a reaction model was developed to predict the CO 2 flux for 1 M K-SAR at different temperatures, demonstrating good agreement between experimental and theoretical fluxes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Simple but tricky: Investigations of terephthalic acid purity obtained from mixed PET waste

In this study, we report for the first time, the basic depolymerization of mixed waste-polyethylene terephthalate (PET) by hydrolysis and subsequent terephthalic acid monomer recovery at high purity using benign reaction conditions. Several conditions were tested for depolymerization such as PET chips size, concentration of aqueous sodium hydroxide (20 or 30%), organic co-solvent (ethylene glycol or ethanol), temperature at which the reaction was run and duration of the heating. More importantly, several batches of PET were utilized as starting materials including a commercial PET, chopped PET obtained from clean bottles whose caps and labels were removed and the purity of the product from each condition was evaluated via nuclear magnetic resonance (1HNMR and 13CNMR), differential scanning calorimetry (DSC) and powder Xray diffraction (XRD). Unsurprisingly, the conversion of PET is dependent on the particle size varying from 100% conversion for fine powder to 73% conversion for (300 µm, mesh 6 – 20 or mesh 14-20). Ethanol appears to be more efficient as a co-solvent than ethylene glycol, with higher PET depolymerization conversions (94% versus 75-80%), shorter reaction times (2h versus 6h) and lower temperatures (80 °C versus 110 °C). The terephthalic acid (TPA) recovered appeared to have only subtle differences among the batches, most notably a pink color when the reaction was run in ethanol/base. The DSC of the compounds produced in ethylene glycol water appear to display a melting point (280-288 °C) while the samples prepared in ethanol as well as a commercial sample did not. Overall, the purity of the various TPA batches is comparable, and similar to commercial TPA, demonstrating the utility of the method to depolymerize realistic waste streams. The method is simple, demonstrated on multigram scale (15-30g) and allows for the complete removal of waste other than PET unaffected by alkaline conditions.

Cosimbescu, Lelia↗

DOE OSTI2022

Self-Assembly of Partially Charged Diblock Copolymer-Homopolymer Ternary Blends

Ternary blends comprising of a diblock copolymer and the corresponding homopolymers provide ready access to a variety of morphologies, but the impact of charge on their phase behavior has not been studied extensively. Here, three partially charged ternary blends consisting of symmetric poly[(oligo(ethylene glycol) methyl ether methacrylate-co-oligo(ethylene glycol) propyl sodium sulfonate methacrylate)] (POEGMA#), polystyrene (PS), and POEGMA#-PS with different charge fractions were prepared, where # denotes the mole fraction of charged monomers in the POEGMA chain. Here, the phase behavior was systematically studied using small-angle X-ray scattering (SAXS), and isothermal phase diagrams at 120 °C were constructed. The resulting isothermal planes contain a wide lamellar (LAM) phase window with a slight deviation from symmetry for ion-containing ternary blends, due to the homopolymer size difference. Given the absence of any significant change in the phase diagrams as the charge fraction increases, the role of charge is primarily to increase the segregation strength in the ternary system, as in the case of partially charged diblock polymers. In addition, examination of the increase in domain size along the volumetrically symmetric isopleth reveals a “dry-brush” like swelling behavior of homopolymers in all three blends, presumably due to the space-filling nature of the oligomeric ethylene glycol side chains on POEGMA.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗