SEARCH · Engineering Papers

Results for “full approximation scheme”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS1986

Thermodynamic evaluation of transonic compressor rotors using the finite volume approach

A method was developed which calculates two-dimensional, transonic, viscous flow in ducts. The finite volume, time marching formulation is used to obtain steady flow solutions of the Reynolds-averaged form of the Navier Stokes equations. The entire calculation is performed in the physical domain. The method is currently limited to the calculation of attached flows. The features of the current method can be summarized as follows. Control volumes are chosen so that smoothing of flow properties, typically required for stability, is now needed. Different time steps are used in the different governing equations to improve the convergence speed of the viscous calculations. A new pressure interpolation scheme is introduced which improves the shock capturing ability of the method. A multi-volume method for pressure changes in the boundary layer allows calculations which use very long and thin control volumes. A special discretization technique is also used to stabilize these calculations. A special formulation of the energy equation is used to provide improved transient behavior of solutions which use the full energy equation. The method is then compared with a wide variety of test cases. The freestream Mach numbers range from 0.075 to 2.8 in the calculations. Transonic viscous flow in a converging diverging nozzle is calculated with the method; the Mach number upstream of the shock is approximately 1.25. The agreement between the calculated and measured shock strength and total pressure losses is good. Essentially incompressible turbulent boundary layer flow in a adverse pressure gradient is calculated and the computed distribution of mean velocity and shear stress are in good agreement with the measurements. At the other end of the Mach number range, a flat plate turbulent boundary layer with a freestream Mach number of 2.8 is calculated using the full energy equation; the computed total temperature distribution and recovery factor agree well with the measurements when a variable Prandtl number is used through the boundary layer.

Nicholson, S.↗

NASA NTRS1999

Solving Upwind-Biased Discretizations: Multigrid Solver Using Semicoarsening - 2

This paper studies a novel multigrid approach to the solution for a second order upwind biased discretization of the convection equation in two dimensions. This approach is based on semi-coarsening and well balanced explicit correction terms added to coarse-grid operators to maintain on coarse-grid the same cross-characteristic interaction as on the target (fine) grid. Colored relaxation schemes are used on all the levels allowing a very efficient parallel implementation. The results of the numerical tests can be summarized as follows: 1) The residual asymptotic convergence rate of the proposed V(0, 2) multigrid cycle is about 3 per cycle. This convergence rate far surpasses the theoretical limit (4/3) predicted for standard multigrid algorithms using full coarsening. The reported efficiency does not deteriorate with increasing the cycle, depth (number of levels) and/or refining the target-grid mesh spacing. 2) The full multi-grid algorithm (FMG) with two V(0, 2) cycles on the target grid and just one V(0, 2) cycle on all the coarse grids always provides an approximate solution with the algebraic error less than the discretization error. Estimates of the total work in the FMG algorithm are ranged between 18 and 30 minimal work units (depending on the target (discretizatioin). Thus, the overall efficiency of the FMG solver closely approaches (if does not achieve) the goal of the textbook multigrid efficiency. 3) A novel approach to deriving a discrete solution approximating the true continuous solution with a relative accuracy given in advance is developed. An adaptive multigrid algorithm (AMA) using comparison of the solutions on two successive target grids to estimate the accuracy of the current target-grid solution is defined. A desired relative accuracy is accepted as an input parameter. The final target grid on which this accuracy can be achieved is chosen automatically in the solution process. the actual relative accuracy of the discrete solution approximation obtained by AMA is always better than the required accuracy; the computational complexity of the AMA algorithm is (nearly) optimal (comparable with the complexity of the FMG algorithm applied to solve the problem on the optimally spaced target grid).

Diskin, Boris↗

DOE OSTI2021

Nucleon-pair coupling scheme in Elliott's SU(3) model

Elliott's SU(3) model is at the basis of the shell-model description of rotational motion in atomic nuclei. Here we demonstrate that SU(3) symmetry can be realized in a truncated shell-model space if constructed in terms of a sufficient number of collective S, D, G,...pairs (i.e., with angular momentum zero, two, four,...) and if the structure of the pairs is optimally determined either by a conjugate-gradient minimization method or from a Hartree-Fock intrinsic state. We illustrate the procedure for six protons and six neutrons in the pf (sdg) shell and exactly reproduce the level energies and electric quadrupole properties of the ground-state rotational band with SDG (SDGI) pairs. The SD-pair approximation without significant renormalization, on the other hand, cannot describe the full SU(3) collectivity. A mapping from Elliott's fermionic SU(3) model to systems with s, d, g,... bosons provides insight into the existence of a decoupled collective subspace in terms of S, D, G,... pairs.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2025

Loss-of-Coolant Accident Analysis of a High-Burnup Pressurized Water Reactor Core Design Using Gadolinia-Doped UO 2

High-burnup and extended enrichment fuels are of interest for extending the cycle lengths of pressurized water reactors from 18 to 24 months. Changes to the fuel design and core loading scheme have potentially significant safety implications due to power distribution effects, reduced thermal conductivity, and/or increased plenum pressures due to additional burnable poison loadings. Additionally, higher burnups result in increased material degradation and risk of fuel fragmentation, relocation, and dispersal (FFRD). A representative 24-month core design using gadolinia-doped UO 2 was analyzed for performance under large-break (LB) loss-of-coolant accident (LOCA) conditions using PARCS, RELAP5-3D, and BISON. Furthermore, all considered acceptance criteria were met, with no cases exceeding the 1477 K maximum cladding temperature or the post-quench ductility oxidation limit of 17% equivalent cladding reacted. Full-core FFRD susceptibility was estimated to be approximately 455 kg, though high uncertainties exist with current approaches for computing susceptibility. Undoped fuel rods are more likely to be limiting due to higher linear heat rates. Relatively high burnup and linear heat rate rods located in second batch assemblies are of greatest safety significance during LB LOCA for this high-burnup core design.

High burnup↗

NASA NTRS2021

Newmark-Type Pseudo-Three-Dimensional Back-Analysis of Co-Seismic Landslides in Egkremnoi, Lefkada, Greece

A pseudo-three-dimensional (pseudo-3D) methodology to back-analyze coseismic landslides was developed and applied to 68mapped landslides, which occurred over approximately 1 km2area in Egkremnoi, Greece, during the 2015 Mw6.5 Lefkada earthquake. The methodology is based on a one-dimensional (1D) Newmark-type sliding block model to assess instability and a spatial projection in 3D topography to derive landslide geometry. The strength parameters for modeled landslides that best match the landslide location, area, and volume were derived through an iterative scheme that optimizes the match using predefined matching criteria. The range of different-sized landslides produced shear strength estimates from ~10 to 300 kPa and led to the derivation of a regionally averaged strength envelope characterized by a cohesion of 6 kPa and a friction angle of 53°for the highly fractured limestones that are encountered in this area. Compared to previous full 3Dslope stability analyses in this area, the friction angle using this methodology was found to be generally consistent, but the cohesion was lower. The presented methodology can provide a computationally efficient method to estimate the average shear strength of a geologic unit over large areas, especially where extensive field and laboratory tests on the materials are unavailable or difficult to conduct.

Weibing Gong↗

DOE OSTI2022

A BOUT++ extension for full annular tokamak edge MHD and turbulence simulations

For tokamak edge plasma simulation, a plasma simulation framework BOUT++ employs a dual coordinate system to simulate moderate-n and high-n plasma instability with reasonable computational cost, where n is the toroidal mode number. This coordinate system however limits the computational domain to the toroidal wedge (full torus divided into N parts in the toroidal direction) for computational efficiency and the use of flute-ordering approximation in the field solver calculating the flow potential from the vorticity which may not be valid for low-n modes. Improving numerical treatment of low-n modes is however indispensable to address simulations of low-n current-driven edge localized mode (ELM), ELM control by resonant magnetic perturbations (RMPs), edge turbulence with RMPs and so on. In this work, BOUT++ is extended to simulate the interplay between $n=0$, low-n and high-n plasma components in a full annular tokamak edge domain through hybrid modeling of the flow potential and the vorticity. Low-n modes of flow potential are calculated in an orthogonal flux surface coordinate and high-n modes in the dual coordinate system separately in Fourier space. Finally, the proposed scheme can capture an interplay between $n=1$ global modes and high-n turbulence during pedestal collapse in a full annular torus domain with a circular cross section.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1980

An implicit algorithm for the transonic full-potential equation in conservative form

A fast, implicit approximate factorization algorithm for the solution of the conservative full-potential equation for transonic flow in two and three dimensions is presented. Stability in supersonic regions is maintained by the use of an upwind evaluation of the density coefficient along all coordinate directions, providing an effective upwind difference of the streamwise terms for any orientation of the velocity vector and thereby enhancing the reliability of the algorithm. The algorithm is shown to provide rapid convergence for the computation of certain difficult two-dimensional test cases, including cases with fishtail shock patterns, demonstrating the reliability and efficiency of the procedure. Surface pressure coefficient distributions obtained by the present method are also found to be in good agreement with those computed by successive-line overrelaxation and a hybrid direct-solver/successive-line overrelaxation scheme, with significant reductions in CPU time required. A three-dimensional solution for a swept wing mounted between parallel walls is also presented which demonstrates the high convergence rate of the algorithm in three dimensions as well as two.

Holst, T.↗

NASA NTRS2004

Adjoint Algorithm for CAD-Based Shape Optimization Using a Cartesian Method

Adjoint solutions of the governing flow equations are becoming increasingly important for the development of efficient analysis and optimization algorithms. A well-known use of the adjoint method is gradient-based shape optimization. Given an objective function that defines some measure of performance, such as the lift and drag functionals, its gradient is computed at a cost that is essentially independent of the number of design variables (geometric parameters that control the shape). More recently, emerging adjoint applications focus on the analysis problem, where the adjoint solution is used to drive mesh adaptation, as well as to provide estimates of functional error bounds and corrections. The attractive feature of this approach is that the mesh-adaptation procedure targets a specific functional, thereby localizing the mesh refinement and reducing computational cost. Our focus is on the development of adjoint-based optimization techniques for a Cartesian method with embedded boundaries.12 In contrast t o implementations on structured and unstructured grids, Cartesian methods decouple the surface discretization from the volume mesh. This feature makes Cartesian methods well suited for the automated analysis of complex geometry problems, and consequently a promising approach to aerodynamic optimization. Melvin et developed an adjoint formulation for the TRANAIR code, which is based on the full-potential equation with viscous corrections. More recently, Dadone and Grossman presented an adjoint formulation for the Euler equations. In both approaches, a boundary condition is introduced to approximate the effects of the evolving surface shape that results in accurate gradient computation. Central to automated shape optimization algorithms is the issue of geometry modeling and control. The need to optimize complex, "real-life" geometry provides a strong incentive for the use of parametric-CAD systems within the optimization procedure. In previous work, we presented an effective optimization framework that incorporates a direct-CAD interface. In this work, we enhance the capabilities of this framework with efficient gradient computations using the discrete adjoint method. We present details of the adjoint numerical implementation, which reuses the domain decomposition, multigrid, and time-marching schemes of the flow solver. Furthermore, we explain and demonstrate the use of CAD in conjunction with the Cartesian adjoint approach. The final paper will contain a number of complex geometry, industrially relevant examples with many design variables to demonstrate the effectiveness of the adjoint method on Cartesian meshes.

Nemec, Marian↗

NASA NTRS1978

A note on the diurnal averaging of aeronomical models

An approximate technique for diurnally time-averaging atmospheric photochemical-dynamical models which eliminates the need for a detailed numerical resolution of sunrise and sunset transitions is developed. The scheme is equivalent to scaling certain chemical rate constants and photodissociation coefficients by appropriate aeronomical factors. To calculate the scaling factors, diurnal variations are parameterized with a step-function behavior, assuming that each species has a constant day-time and night-time concentration whose ratio can be determined by analyzing the chemical interactions occurring after sunset. The solution accounts for the effects of night-time reactions on the 24 h average values of species abundances, and on the average daily rates of the catalytic processes consuming ozone in the stratosphere. The accuracy of the technique is demonstrated by comparing its predictions to those of a full diurnal simulation; typically, the precision is better than 10%. By contrast, it is shown that the use of some other well-known computational schemes can result in significantly larger predictive errors.

Turco, R. P.↗

NASA NTRS1995

Navier-Stokes Aerodynamic Simulation of the V-22 Osprey on the Intel Paragon MPP

The paper will describe the Development of a general three-dimensional multiple grid zone Navier-Stokes flowfield simulation program (ENS3D-MPP) designed for efficient execution on the Intel Paragon Massively Parallel Processor (MPP) supercomputer, and the subsequent application of this method to the prediction of the viscous flowfield about the V-22 Osprey tiltrotor vehicle. The flowfield simulation code solves the thin Layer or full Navier-Stoke's equation - for viscous flow modeling, or the Euler equations for inviscid flow modeling on a structured multi-zone mesh. In the present paper only viscous simulations will be shown. The governing difference equations are solved using a time marching implicit approximate factorization method with either TVD upwind or central differencing used for the convective terms and central differencing used for the viscous diffusion terms. Steady state or Lime accurate solutions can be calculated. The present paper will focus on steady state applications, although time accurate solution analysis is the ultimate goal of this effort. Laminar viscosity is calculated using Sutherland's law and the Baldwin-Lomax two layer algebraic turbulence model is used to compute the eddy viscosity. The Simulation method uses an arbitrary block, curvilinear grid topology. An automatic grid adaption scheme is incorporated which concentrates grid points in high density gradient regions. A variety of user-specified boundary conditions are available. This paper will present the application of the scalable and superscalable versions to the steady state viscous flow analysis of the V-22 Osprey using a multiple zone global mesh. The mesh consists of a series of sheared cartesian grid blocks with polar grids embedded within to better simulate the wing tip mounted nacelle. MPP solutions will be shown in comparison to equivalent Cray C-90 results and also in comparison to experimental data. Discussions on meshing considerations, wall clock execution time, load balancing, and scalability will be provided.

Vadyak, Joseph↗

NASA NTRS1997

The Effect of Diffusional Transport and Surface Catalysis on the Aerothermodynamic Heating for Martian Atmospheric Entry

For the reentry heating of 70-degree blunt sphere-cones entering Mars at velocities in excess of 6 km/sec, a study was performed to determine the magnitude of both convective and catalytic heating on the cone forebody. Case studies of the peak heating conditions for the current NASA Mars Pathfinder entry probe, as well as the peak heating conditions of the proposed NASA Mars 2001 aerobraking orbiter mission were performed. Since the actual behavior of the chemical recombination of Mars atmosphere hypersonic shock layer species on heat shield materials is not known, and no experimental studies of any consequence have been done to determine surface reaction rates for the CO2 system, a parametric analysis of various reaction schemes and surface catalytic mechanistic models was performed. In many cases the actual Mars entry probe will have a heat shield composed of an ablative material which can either partially or completely preclude the existence of catalytic surface recombination phenomena. The extent of this blockage effect has not been examined at this time and is not considered in this effort. Instead only non-ablative computations are performed to separately evaluate the full extent of the surface catalysis and related diffusional phenomena. Parametric studies include peak heating point comparisons of non-catalytic, partially catalytic and fully catalytic total surface heat transfer for three difference surface recombination catalytic mechanisms (with and without simultaneous CO + O and O + O recombination) as well as with different species diffusion models. Diffusion model studies include constant Schmidt number (equal diffusivities) and the bifurcation, approximate multi-component diffusion model. Since the gas phase reaction kinetics for the Mars CO2 based atmosphere have also not been validated, the effect of two different (fast and slow) sets of gas kinetics on heat transfer is presented.

Henline, William D.↗

NASA NTRS2006

Less-Complex Method of Classifying MPSK

An alternative to an optimal method of automated classification of signals modulated with M-ary phase-shift-keying (M-ary PSK or MPSK) has been derived. The alternative method is approximate, but it offers nearly optimal performance and entails much less complexity, which translates to much less computation time. Modulation classification is becoming increasingly important in radio-communication systems that utilize multiple data modulation schemes and include software-defined or software-controlled receivers. Such a receiver may "know" little a priori about an incoming signal but may be required to correctly classify its data rate, modulation type, and forward error-correction code before properly configuring itself to acquire and track the symbol timing, carrier frequency, and phase, and ultimately produce decoded bits. Modulation classification has long been an important component of military interception of initially unknown radio signals transmitted by adversaries. Modulation classification may also be useful for enabling cellular telephones to automatically recognize different signal types and configure themselves accordingly. The concept of modulation classification as outlined in the preceding paragraph is quite general. However, at the present early stage of development, and for the purpose of describing the present alternative method, the term "modulation classification" or simply "classification" signifies, more specifically, a distinction between M-ary and M'-ary PSK, where M and M' represent two different integer multiples of 2. Both the prior optimal method and the present alternative method require the acquisition of magnitude and phase values of a number (N) of consecutive baseband samples of the incoming signal + noise. The prior optimal method is based on a maximum- likelihood (ML) classification rule that requires a calculation of likelihood functions for the M and M' hypotheses: Each likelihood function is an integral, over a full cycle of carrier phase, of a complicated sum of functions of the baseband sample values, the carrier phase, the carrier-signal and noise magnitudes, and M or M'. Then the likelihood ratio, defined as the ratio between the likelihood functions, is computed, leading to the choice of whichever hypothesis - M or M'- is more likely. In the alternative method, the integral in each likelihood function is approximated by a sum over values of the integrand sampled at a number, 1, of equally spaced values of carrier phase. Used in this way, 1 is a parameter that can be adjusted to trade computational complexity against the probability of misclassification. In the limit as 1 approaches infinity, one obtains the integral form of the likelihood function and thus recovers the ML classification. The present approximate method has been tested in comparison with the ML method by means of computational simulations. The results of the simulations have shown that the performance (as quantified by probability of misclassification) of the approximate method is nearly indistinguishable from that of the ML method (see figure).

Hamkins, Jon↗

DOE OSTI2022

Comparison of spherical harmonics method and discrete ordinates method for radiative transfer in a turbulent jet flame

Here, in this study, we systematically compared the accuracy and computational cost of two popular solution methods for the radiative transfer equation (RTE): the spherical harmonics method (P N ) and the discrete ordinates method (DOM). We first investigated convergence characteristics of different orders of P N and DOM in a series of 1D homogeneous configurations with varying optical thicknesses. Both solvers perform better for optically thicker cases. The accuracy of P N methods increases with its order, , but the gain in accuracy reduces with the increase in , i.e., improvement of P 7 over P 5 is less than that of P 3 over P 1 . This decreasing trend becomes more prominent as the optical thickness decreases. On the other hand, DOM’s accuracy increases almost linearly with the increase in the number of ordinates (or polar angles in this study) in all cases. While comparing the directional profile of radiative intensity, both solvers perform better when the radiative intensity is more isotropic. These solvers were then connected with a full spectrum k-distribution (FSK) spectral model and used to perform radiation-coupled simulations of a turbulent jet flame in an axi-symmetric cylindrical domain. Results obtained from P 1 to P 7 approximations for P N , and 2 x 4, 4 x 4, 4 x 8, 8 x 8 finite angles for DOM are compared with that from an optically thin model, and a reference solution from line-by-line (LBL) photon Monte Carlo (PMC) method. The choice of radiation solver shows a noticeable impact on the temperature distribution of the flame. The P N solvers lead to slightly higher radiant fractions and the DOM solvers lead to slightly lower radiant fractions than the PMC benchmark solution. Finally, the computational costs of each of these solvers are also reported and an intermittent evaluation / time blending scheme to improve the computational efficiency of radiation solvers in radiation-coupled simulations are also demonstrated.

42 ENGINEERING↗

NASA NTRS1994

TOPEX/POSEIDON tides estimated using a global inverse model

Altimetric data from the TOPEX/POSEIDON mission will be used for studies of global ocean circulation and marine geophysics. However, it is first necessary to remove the ocean tides, which are aliased in the raw data. The tides are constrained by the two distinct types of information: the hydrodynamic equations which the tidal fields of elevations and velocities must satisfy, and direct observational data from tide gauges and satellite altimetry. Here we develop and apply a generalized inverse method, which allows us to combine rationally all of this information into global tidal fields best fitting both the data and the dynamics, in a least squares sense. The resulting inverse solution is a sum of the direct solution to the astronomically forced Laplace tidal equations and a linear combination of the representers for the data functionals. The representer functions (one for each datum) are determined by the dynamical equations, and by our prior estimates of the statistics or errors in these equations. Our major task is a direct numerical calculation of these representers. This task is computationally intensive, but well suited to massively parallel processing. By calculating the representers we reduce the full (infinite dimensional) problem to a relatively low-dimensional problem at the outset, allowing full control over the conditioning and hence the stability of the inverse solution. With the representers calculated we can easily update our model as additional TOPEX/POSEIDON data become available. As an initial illustration we invert harmonic constants from a set of 80 open-ocean tide gauges. We then present a practical scheme for direct inversion of TOPEX/POSEIDON crossover data. We apply this method to 38 cycles of geophysical data records (GDR) data, computing preliminary global estimates of the four principal tidal constituents, M(sub 2), S(sub 2), K(sub 1) and O(sub 1). The inverse solution yields tidal fields which are simultaneously smoother, and in better agreement with altimetric and ground truth data, than previously proposed tidal models. Relative to the 'default' tidal corrections provided with the TOPEX/POSEIDON GDR, the inverse solution reduces crossover difference variances significantly (approximately 20-30%), even though only a small number of free parameters (approximately equal to 1000) are actually fit to the crossover data.

Egbert, Gary D.↗

DOE OSTI2023

Acoustic Codes in 2D Spherical Coordinate

Finite-difference methods are widely used to simulate infrasound propagation in the atmosphere. Flexibility of finite-difference scheme allows implementation of highly heterogeneous media for sound propagation as well as complex source models for sound generation. While full 3-D finite-difference methods have been utilized for local infrasound propagation with pronounced topography, 2-D modeling approach has been preferred for regional and global propagation as full 3-D methods generally require enormous computational resources. Infrasound propagation is often simulated with a second-order finite difference scheme. This lowest-order finite-difference scheme is robust and straightforward to implement complex boundary conditions, but the solution includes large error with numerical dispersion and dissipation. This large numerical error may make the second-order finite-difference not optimal for long range infrasound propagation modeling as the numerical dispersion degrades the accuracy of the solution unacceptably. Here, we developed a high-order finite-difference solver for long-range infrasound simulation. The high-order scheme is particularly popular for linear wave modeling in aeroacoustics owing to its low-dispersive and low-dissipative behavior. We develop and evaluate a high-order finite difference scheme in 2-D axisymmetric coordinates. The axisymmetry allows to approximate 3-D spherical sound propagation and amplitude attenuation by a 2-D method. AC2Dr is developed to simulate infrasound propagation in realistic atmosphere, but can be used for linear acoustic waves in general materials with background flow. AC2Dr in an axisymmetric coordinates allows for spherical radiation of acoustic waves from compact sources.

Sjogreen, Bjorn↗

NASA NTRS1998

Io's Plasma Environment During the Galileo Flyby: Global Three-Dimensional MHD Modeling with Adaptive Mesh Refinement

The first results for applying a three-dimensional multimedia ideal MHD model for the mass-loaded flow of Jupiter's corotating magnetospheric plasma past Io are presented. The model is able to consider simultaneously physically realistic conditions for ion mass loading, ion-neutral drag, and intrinsic magnetic field in a full global calculation without imposing artificial dissipation. Io is modeled with an extended neutral atmosphere which loads the corotating plasma torus flow with mass, momentum, and energy. The governing equations are solved using adaptive mesh refinement on an unstructured Cartesian grid using an upwind scheme for AHMED. For the work described in this paper we explored a range of models without an intrinsic magnetic field for Io. We compare our results with particle and field measurements made during the December 7, 1995, flyby of to, as published by the Galileo Orbiter experiment teams. For two extreme cases of lower boundary conditions at Io, our model can quantitatively explain the variation of density along the spacecraft trajectory and can reproduce the general appearance of the variations of magnetic field and ion pressure and temperature. The net fresh ion mass-loading rates are in the range of approximately 300-650 kg/s, and equivalent charge exchange mass-loading rates are in the range approximately 540-1150 kg/s in the vicinity of Io.

Combi, M. R.↗

NASA NTRS2006

Adjoint Sensitivity Computations for an Embedded-Boundary Cartesian Mesh Method and CAD Geometry

Cartesian-mesh methods are perhaps the most promising approach for addressing the issues of flow solution automation for aerodynamic design problems. In these methods, the discretization of the wetted surface is decoupled from that of the volume mesh. This not only enables fast and robust mesh generation for geometry of arbitrary complexity, but also facilitates access to geometry modeling and manipulation using parametric Computer-Aided Design (CAD) tools. Our goal is to combine the automation capabilities of Cartesian methods with an eficient computation of design sensitivities. We address this issue using the adjoint method, where the computational cost of the design sensitivities, or objective function gradients, is esseutially indepeudent of the number of design variables. In previous work, we presented an accurate and efficient algorithm for the solution of the adjoint Euler equations discretized on Cartesian meshes with embedded, cut-cell boundaries. Novel aspects of the algorithm included the computation of surface shape sensitivities for triangulations based on parametric-CAD models and the linearization of the coupling between the surface triangulation and the cut-cells. The objective of the present work is to extend our adjoint formulation to problems involving general shape changes. Central to this development is the computation of volume-mesh sensitivities to obtain a reliable approximation of the objective finction gradient. Motivated by the success of mesh-perturbation schemes commonly used in body-fitted unstructured formulations, we propose an approach based on a local linearization of a mesh-perturbation scheme similar to the spring analogy. This approach circumvents most of the difficulties that arise due to non-smooth changes in the cut-cell layer as the boundary shape evolves and provides a consistent approximation tot he exact gradient of the discretized abjective function. A detailed gradient accurace study is presented to verify our approach. Thereafter, we focus on a shape optimization problem for an Apollo-like reentry capsule. The optimization seeks to enhance the lift-to-drag ratio of the capsule by modifyjing the shape of its heat-shield in conjunction with a center-of-gravity (c.g.) offset. This multipoint and multi-objective optimization problem is used to demonstrate the overall effectiveness of the Cartesian adjoint method for addressing the issues of complex aerodynamic design. This abstract presents only a brief outline of the numerical method and results; full details will be given in the final paper.

Nemec, Marian↗

NASA NTRS2000

Estimates of Ground Temperature and Atmospheric Moisture from CERES Observations

A method is developed to retrieve surface ground temperature (Tg) and atmospheric moisture using clear sky fluxes (CSF) from CERES-TRMM observations. In general, the clear sky outgoing long-wave radiation (CLR) is sensitive to upper level moisture (q(sub h)) over wet regions and Tg over dry regions The clear sky window flux from 800 to 1200 /cm (RadWn) is sensitive to low level moisture (q(sub j)) and Tg. Combining these two measurements (CLR and RadWn), Tg and q(sub h) can be estimated over land, while q(sub h) and q(sub t) can be estimated over the oceans. The approach capitalizes on the availability of satellite estimates of CLR and RadWn and other auxiliary satellite data. The basic methodology employs off-line forward radiative transfer calculations to generate synthetic CSF data from two different global 4-dimensional data assimilation products. Simple linear regression is used to relate discrepancies in CSF to discrepancies in Tg, q(sub h) and q(sub t). The slopes of the regression lines define sensitivity parameters that can be exploited to help interpret mismatches between satellite observations and model-based estimates of CSF. For illustration, we analyze the discrepancies in the CSF between an early implementation of the Goddard Earth Observing System Data Assimilation System (GEOS-DAS) and a recent operational version of the European Center for Medium-Range Weather Prediction data assimilation system. In particular, our analysis of synthetic total and window region SCF differences (computed from two different assimilated data sets) shows that simple linear regression employing (Delta)Tg and broad layer (Delta)q(sub l) from 500 hPa to surface and (Delta)q(sub h) from 200 to 500 hPa provides a good approximation to the full radiative transfer calculations, typically explaining more than 90% of the 6-hourly variance in the flux differences. These simple regression relations can be inverted to "retrieve" the errors in the geophysical parameters. Uncertainties (normalized by standard deviation) in the monthly mean retrieved parameters range from 7% for (Delta)T to about 20% for (Delta)q(sub t). Our initial application of the methodology employed an early CERES-TRMM data set (CLR and Radwn) to assess the quality of the GEOS2 data. The results showed that over the tropical and subtropical oceans GEOS2 is, in general, too wet in the upper troposphere (mean bias of 0.99 mm) and too dry in the lower troposphere (mean bias of -4.7 mm). We note that these errors, as well as a cold bias in the Tg, have largely been corrected in the current version of GEOS-2 with the introduction of a land surface model, a moist turbulence scheme and the assimilation of SSTM/I total precipitable water.

Wu, Man Li C.↗