Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

A vortex-lattice method for general, unsteady aerodynamics

A general method of calculating unsteady, incompressible, inviscid, three-dimensional flows around arbitrary planforms has been developed. The method is an extension of the vortex-lattice technique. It is not limited by aspect ratio, camber, or angle of attack, as long as vortex breakdown does not occur above the surface of the wing and separation occurs only along sharp edges. As the wing performs arbitrary maneuvers, the position of the wake and the distribution of circulation on the wing and in the wake are obtained as functions of time. One desirable feature of the present method is its ability to treat steady lifting flows very efficiently. Several examples of steady and unsteady flows are presented. These include rectangular wings, with and without flaps, delta, and cropped delta wings.

Konstadinopoulos, P.↗

Flow control around a circular cylinder using pulsed dielectric barrier discharge surface plasma

Dielectric barrier discharge (DBD) plasma actuators have been used to control the flow around a circular cylinder at Re=15 000, where the near-wake structure was studied using time-resolved particle image velocimetry with simultaneous measurements of the dynamic lift and drag forces. It was shown that the vortex shedding was suppressed when the surface plasma placed near the natural separation point was activated in a pulsed mode at nondimensional frequency, f{sub p}{sup +}, above 0.6 with a force coefficient, C{sub p}, greater than 0.05%. Plasma actuator performance on flow control was summarized by mapping the changes in drag and lift fluctuations as a function of the forcing frequency and the force coefficient. They showed that more than 70% reduction in lift fluctuations was obtained with up to 32% drag reduction at f{sub p}{sup +}=2.0 and C{sub p}=0.32%. Here, narrowing of the wake was observed as the plasma promoted shear-layer roll-ups at the forcing frequency. This, however, did not affect the shear layer on the opposite side of the wake. At nondimensional forcing frequencies less than 0.6, the vortex shedding locked onto a multiple of the plasma frequency to amplify the wake oscillations. This caused more than 85% increase in lift fluctuations with 8% drag increase at f{sub p}{sup +}=0.2 and C{sub p}=0.01%. The efficiency of flow control using DBD plasma was found to be 1%-2% for drag reduction while around 6% for drag increase.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Resonance energy flow dynamics of coherently delocalized excitons in biological and macromolecular systems: Recent theoretical advances and open issues

Recent experimental and theoretical studies suggest that biological photosynthetic complexes utilize the quantum coherence in a positive manner for efficient and robust flow of electronic excitation energy. Clear and quantitative understanding of such suggestion is important for identifying the design principles behind efficient flow of excitons coherently delocalized over multiple chromophores in condensed environments. Adaptation of such principles for synthetic macromolecular systems has also significant implication for the development of novel photovoltaic systems. Advanced theories of resonance energy transfer are presented here, which can address these issues. Applications to photosynthetic light harvesting complex systems and organic materials demonstrate the capabilities of new theoretical approaches and future challenges.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

AN OVERVIEW OF THE DESIGN AND PERFORMANCE TESTING OF A 275 BAR INTEGRALLY GEARED SUPERCRITICAL CO2 COMPRESSOR FOR POWER GENERATION

An integrally geared compressor-expander (compander) for supercritical CO2 (sCO2) was developed to convert thermal energy to electricity. With operating pressures of 275 bar, this turbomachine represents the state of the art in integrally geared machine architecture, hitting compressor inlet densities of 600 kg/m3 and discharge pressures of 275 bar. The product development was funded by the Department of Energy’s Energy Efficiency and Renewable Energy Office under EE0007114 to advance the state of the art in concentrated solar power applications; however, the technology itself is agnostic to heat source, and is predicted to achieve a thermal-to-electric conversion efficiency of 50% for any indirect heat source capable of providing turbine inlet temperatures of 700°C or greater. While the program encompassed the design and testing for the compressor and turbine elements, this paper will focus on the compressor design and operation. The paper will begin with an introduction to the cycle design and analysis of an indirectly heated integrally geared sCO2 compander, a discussion of the mechanical and aerodynamic design of the compressor that is a two stage radial compressor operating subcritically at 27,512 rpm, and will then proceed to describe the test facility and measured data to characterize the performance and robustness of the machine. The paper will conclude with a discussion on lessons learned throughout the course of commissioning and testing. Practical aspects of testing a compressor operating near the dome including complications relating to obtaining an accurate compressor flow map, efficiency calculations, flow unsteadiness, and associated measurement uncertainties will be discussed.

wilkes, jason↗

Laminar flow integration: Flight tests status and plans

Under the Aircraft Energy Efficiency - Laminar Flow Control Program, there are currently three flight test programs under way to address critical issues concerning laminar flow technology application to commercial transports. The Leading-Edge Flight Test (LEFT) with a JetStar aircraft is a cooperative effort with the Ames/Dryden Flight Research Facility to provide operational experience with candidate leading-edge systems representative of those that might be used on a future transport. In the Variable Sweep Transition Flight Experiment (VSTFE), also a cooperative effort between Langley and Ames/Dryden, basic transition data on an F-14 wing with variable sweep will be obtained to provide a data base for laminar flow wing design. Finally, under contract to the Boeing Company, the acoustic environment on the wing of a 757 aircraft will be measured and the influence of engine noise on laminar flow determined with a natural laminar flow glove on the wing. The status and plans for these programs are reported.

Wagner, R. D.↗

In-situ tube burst testing and high-temperature deformation behavior of candidate materials for accident tolerant fuel cladding

The high resistance of cladding to plastic deformation and burst failure is one of the most essential properties of accident tolerant fuel (ATF) for maintaining structural integrity during a loss-of-coolant accident (LOCA) since the deformation and burst behavior governs the cooling efficiency of flow channels and process of fission product release. To simulate and evaluate such deformation and burst process of thin-walled cladding, an in-situ testing and evaluation method has been developed on the basis of visual imaging and image analysis techniques. The method uses a specialized optics system consisted of a high-resolution video camera, light filtering unit, and monochromatic light sources, and the in-situ testing is performed using a 50 mm long pressurized thin-walled tubular specimen set in a programmable furnace. In this study eleven (11) candidate cladding materials for ATF, i.e., 6 FeCrAl alloys and 5 nanostructured steels, were tested using the newly developed method, and the time-dependent images were analyzed to produce detailed deformation and burst data such as true hoop stress, strain (creep) rate, and failure stress. Relatively soft FeCrAl alloys deformed and burst below 800°C while negligible strain rates were measured for higher strength alloys and/or for relatively thick wall specimens.

Gussev, Maxim N.↗

Wave function analysis with a maximum flow algorithm

An efficient algorithm for computing the maximum-flow path in a network is applied to the identification of the dominant configuration state functions (CSFs) in a graphically contracted function (GCF), configuration interaction, wave function. The flow network is a space of spin-adapted CSFs represented by a Shavitt graph, wherein the nodes correspond to orbital occupations and spin quantum numbers. The graph nodes are connected by arcs, and an arc density is defined as sums of the associated squared CSF coefficients. A max-min approach determines an upper bound to the maximum possible incoming flow for each graph node. A backtracking step generates a candidate walk and is followed by a limited search of alternative branching paths for the dominant CSF. The arc density contributions are removed from the graph, and the algorithm is reapplied to the updated graph. This list of generated walks can be partitioned in order to guarantee that the dominant CSFs have been identified. All of the steps in this algorithm are computationally efficient and do not depend on the potentially large dimension of the underlying linear CSF expansion space. An analysis of low-lying valence states of C-2 illustrates the method.

74 ATOMIC AND MOLECULAR PHYSICS↗

A hybrid adaptive multiresolution approach for the efficient simulation of reactive flows

Computational studies that use block-structured adaptive mesh refinement (AMR) approaches suffer from unnecessarily high mesh resolution in regions adjacent to important solution features. This deficiency limits the performance of AMR codes. In this work a novel hybrid adaptive multiresolution (HAMR) approach to AMR-based calculations is introduced to address this issue. The multiresolution (MR) smoothness indicators are used to identify regions of smoothness on the mesh where the computational cost of individual physics solvers may be decreased by replacing direct calculations with interpolation. We suggest an approach to balance the errors due to the adaptive discretization and the interpolation of physics quantities such that the overall accuracy of the HAMR solution is consistent with that of the MR-driven AMR solution. The performance of the HAMR scheme is evaluated for a range of test problems, from pure hydrodynamics to turbulent combustion.

97 MATHEMATICS AND COMPUTING↗

Toward lower drag with laminar flow technology

The most promising method of achieving significantly lower skin-friction drag of an aircraft component is through the stabilization and maintenance of a laminar boundary layer over a large fraction of its surface. In a number of applications, however, laminar flow is unfeasible and/or undesirable, and the most efficient turbulent flow design must be provided. The development of both laminar and turbulent airfoil and wing designs over the past decade is reviewed. High, medium, and low-speed airfoil concepts are discussed, and some overall comparisons are made for different Reynolds number ranges.

Harvey, W. D.↗

Efficient computation of inviscid flow fields around complex configurations using a multiblock multigrid method

The applicability of a multigrid technique to block-structured, body-fitted meshes is examined focusing on three different strategies. In the first strategy data are exchanged between blocks in each stage of a five-stage Runge-Kutta time-stepping scheme which keeps a possible time lag between blocks to a minimum, but requires a large amount of I/O operations and storage. The second strategy is based on performing a complete Runge-Kutta cycle within a block before switching to the next. In the third strategy both a complete Runge-Kutta cycle and the residual evaluation for the restriction operator are done within a block, allowing a minimum of I/O and storage. The inviscid flow around a wing-body/engine-pylon configuration was computed on a mesh consisting of 11 computational blocks. It was found that both the first and the second strategies delivered converged results, but the third failed due to larger time lag between blocks.

Rossow, C.-C.↗

Agglomeration Multigrid for an Unstructured-Grid Flow Solver

An agglomeration multigrid scheme has been implemented into the sequential version of the NASA code USM3Dns, tetrahedral cell-centered finite volume Euler/Navier-Stokes flow solver. Efficiency and robustness of the multigrid-enhanced flow solver have been assessed for three configurations assuming an inviscid flow and one configuration assuming a viscous fully turbulent flow. The inviscid studies include a transonic flow over the ONERA M6 wing and a generic business jet with flow-through nacelles and a low subsonic flow over a high-lift trapezoidal wing. The viscous case includes a fully turbulent flow over the RAE 2822 rectangular wing. The multigrid solutions converged with 12%-33% of the Central Processing Unit (CPU) time required by the solutions obtained without multigrid. For all of the inviscid cases, multigrid in conjunction with an explicit time-stepping scheme performed the best with regard to the run time memory and CPU time requirements. However, for the viscous case multigrid had to be used with an implicit backward Euler time-stepping scheme that increased the run time memory requirement by 22% as compared to the run made without multigrid.

Frink, Neal↗

Efficient Ionization Investigation for Flow Control and Energy Extraction

Nonequilibrium ionization of air by nonthermal means is explored for hypersonic vehicle applications. The method selected for evaluation generates a weakly ionized plasma using pulsed nanosecond, high-voltage discharges sustained by a lower dc voltage. These discharges promise to provide a means of energizing and sustaining electrons in the air while maintaining a nearly constant ion/neutral molecule temperature. This paper explores the use of short approx.5 nsec, high-voltage approx.12 to 22 kV, repetitive (40 to 100 kHz) discharges in generating a weakly ionized gas sustained by a 1 kV dc voltage in dry air at pressures from 10 to 80 torr. Demonstrated lifetimes of the sustainer discharge current approx.10 to 25 msec are over three orders of magnitude longer than the 5 nsec pulse that generates the electrons. This life is adequate for many high speed flows, enabling the possibility of exploiting weakly ionized plasma phenomena in flow-fields such as those in hypersonic inlets, combustors, and nozzles. Results to date are obtained in a volume of plasma between electrodes in a bell jar. The buildup and decay of the visible emission from the pulser excited air is photographed on an ICCD camera with nanosecond resolution and the time constants for visible emission decay are observed to be between 10 to 15 nsec decreasing as pressure increases. The application of the sustainer voltage does not change the visible emission decay time constant. Energy consumption as indicated by power output from the power supplies is 194 to 669 W depending on pulse repetition rate.

Schneider, Steven J.↗

Wet active chevron nozzle for controllable jet noise reduction

Disposed at or toward the trailing edge of one or more nozzles associated with a jet engine are injection ports which can selectively be made to discharge a water stream into a nozzle flow stream for the purpose of increasing turbulence in somewhat of a similar fashion as mechanically disposed chevrons have done in the known art. Unlike mechanically disposed chevrons of the known art, the fluid flow may be secured thereby increasing the engine efficiency. Various flow patterns, water pressures, orifice designs or other factors can be made operative to provide desired performance characteristics.

Thomas, Russell H.↗