Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fence”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Effects of sweep angle and passive relaminarization devices on a supersonic swept-cylinder boundary layer

The effects of passive leading-edge devices on the boundary layer of a swept cylinder in supersonic flow with very low free-stream disturbance levels are investigated. Tests are conducted at Mach 3.5 over a free-stream Reynolds number based on model diameter of 15,000 to 150,000, and sweep angles of 60 deg and 76 deg are used to evaluate possible sweep-angle effects. The devices tested include a sawtoothed leading edge, square device, and a fence. It is observed that at a sweep angle of 76 deg, relaminarization of the supersonic attachment-line flow is achieved by several of the devices, while no devices are successful at a sweep angle of 60 deg.

Creel, T. R.↗
NASA NTRS1991

Some preliminary results of brush seal/rotor interference effects on leakage at zero and low rpm using a tapered-plug rotor

Some preliminary brush seal leakage results for ambient-temperature air are presented. Data for four nominal brush-rotor radial clearances of -0.09, -0.048, -0.008, and 0.035 mm were taken by using a tapered plug rotor at 0 and 400 rpm with rotor runout of 0.127 mm peak to peak. The brush seal nominal bore diameter was 38 mm with 0.05-mm bristles at 200 bristles/mm of circumference and a 0.61-mm fence height. Leakages were greater than predicted, but agreement was reasonable. Leakage rates were not significantly altered by hysteresis or inlet flow variations. Visualization studies showed that the bristles followed the 400-rpm excitation, and loading studies indicated that bristles slid relative to one another.

Hendricks, R. C.↗
NASA NTRS1991

Wind tunnel investigation of aerodynamic and tail buffet characteristics of leading-edge extension modifications to the F/A-18

The impact of leading-edge extension (LEX) modifications on aerodynamic and vertical tail buffet characteristics of a 16-percent scale F/A-18 model has been investigated in the NASA Langley 30-foot by 60-foot tunnel. Modifications under consideration include variations in LEX chord and span, addition of upper surface fences, and removal of the LEX. Both buffeting and high-angle-of-attack aerodynamics are found to be strongly dependent upon the LEX geometry, which directly influences the strength, position, and breakdown characteristics of the vortex flow field. Concepts aimed at influencing the development of vortical flow field are considered to have much greater potential in design application than those geared toward altering already established flow fields. It is recommended that configuration effects on structural and aerodynamic characteristics be evaluated in parallel, so that trade-off studies can be conducted to ensure adequate structural fatigue life and desired high-angle-of-attack stability and control characteristics in the design of future high performance aircraft.

Shah, Gautam H.↗
NASA NTRS1992

Hand-Switch Unit For Use With Protective Suit

Unit containing two hand-operated switches water-tight and designed for use with protective suit. One switch is toggle switch used to select communication by wire or radio. Other switch is press-to-talk button. User grasps and operates switches without looking at them. Fences on top of new unit protects toggle switch from inadvertent operation and spaced to accommodate gloved thumb. Push-to-talk button protected by longitudinal bar, springy and compressed inward to actuate button.

Chalson, Howard E.↗
NASA NTRS1992

Brush seal leakage performance with gaseous working fluids at static and low rotor speed conditions

The leakage performance of a brush seal with gaseous working fluids at static and low rotor speed conditions was studied. The leakage results are included for air, helium, and carbon dioxide at several bristle/rotor interferences. Also, the effects of packing a lubricant into the bristles and also of reversing the pressure drop across the seal were studied. Results were compared to that of an annular seal at similar operating conditions. In order to generalize the results, they were correlated using corresponding state theory. The brush seal tested had a bore diameter of 3.792 cm (1.4930 in), a fence height of 0.0635 cm (0.025 in), and 1800 bristles/cm circumference (4500 bristles/in circumference). Various bristle/rotor radial interferences were achieved by using a tapered rotor. The brush seal reduced the leakage in comparison to the annular seal, up to 9.5 times. Reversing the pressure drop across the brush seal produced leakage rates approx. the same as that of the annular seal. Addition of a lubricant reduced the leakage by 2.5 times. The air and carbon dioxide data were successfully correlated using corresponding state theory. However, the helium data followed a different curve than the air and carbon dioxide data.

Carlile, Julie A.↗
NASA NTRS1992

Flow field over the wing of a delta-wing fighter model with vortex control devices at Mach 0.6 to 1.2

As part of a cooperative research program between NASA, McDonnell Douglas Corporation, and Wright Research and Development Center, a flow field investigation was conducted on a 7.52 percent scale windtunnel model of an advanced fighter aircraft design. The investigation was conducted in the Langley 16 ft Transonic Tunnel at Mach numbers of 0.6, 0.9, and 1.2. Angle of attack was varied from -4 degrees to 30 degrees and the model was tested at angles of sideslip of 0, 5, and -5 degrees. Data for the over the wing flow field were obtained at four axial survey stations by the use of six 5 hole conical probes mounted on a survey mechanism. The wing leading edge primary vortex exerted the greatest influence in terms of total pressure loss on the over the wing flow field in the area surveyed. A number of vortex control devices were also investigated. They included two different apex flaps, wing leading edge vortex flaps, and small large wing fences. The vortex flap and both apex flaps were beneficial in controlling the wing leading edge primary vortex.

Bare, E. Ann↗
NASA NTRS1990

Quantification of hydrochloric acid and particulate deposition resulting from Space Shuttle launches at John F. Kennedy Space Center, Florida, U.S.A.

Results are presented from studies designed to identify deposition patterns and quantify the ecosystem loading rates of exhaust constituents (which are primarily Al2O3 and HCl) from the Space Shuttle solid rocket motors in the area of the Kennedy Space Center launch pad. Results of measurements indicate that, under certain meteorological conditions, as much as 7.1 x 10 exp 3 kg of particulates and 3.4 x 10 exp 3 kg HCL can be deposited to the near-field environment beyond the launch pad perimeter fence during one STS launch.

Dreschel, Thomas W.↗
NASA NTRS1992

Vortex trapping on a 60 degree delta wing

An experiment was conducted to examine the vortex trapping concept on a 60 deg sweep delta wing at low angles of attack. Using tapered leading edge fences, stable vortices have been successfully trapped. The resulting increase in lift coefficient can be as high as 0.4, which amounts to a 6.5 deg shift in the lift coefficient curve of the delta wing. The corresponding increase in drag coefficient, however, is also significant.

Buchholz, Mark D.↗
NASA NTRS1992

Numerical investigation of tail buffet on F-18 aircraft

Numerical investigation of vortex induced tail buffet is conducted on the F-18 aircraft at high angles of attack. The Reynolds-averaged Navier-Stokes equations are integrated using a time-accurate, implicit procedure. A generalized overset zonal grid scheme is used to decompose the computational space around the complete aircraft with faired-over inlet. A weak coupling between the aerodynamics and structures is assumed to compute the structural oscillation of the flexible vertical tail. Time-accurate computations of the turbulent flow around the F-18 aircraft at 30 degrees angle of attack show the surface and off-surface flowfield details, including the unsteadiness created by the vortex burst and its interaction with the vertical twin tail which causes the tail buffet. The effect of installing a LEX fence on modifying the vortex structure upstream of the tail is also examined.

Rizk, Yehia M.↗
NASA NTRS1992

Full-scale high angle-of-attack tests of an F/A-18

This paper presents an overview of high angle-of-attack tests of a full-scale F/A-18 in the 80- by 120-Foot Wind Tunnel of the National Full-Scale Aerodynamic Complex at NASA Ames Research Center at Moffett Field, California. A production aircraft was tested over an angle-of-attack range of 18 to 50 deg and at wind speeds of up to 100 knots. These tests had three primary test objectives. Pneumatic and mechanical forebody flow control devices were tested at full-scale and shown to produce significant yawing moments for lateral control of the aircraft at high angles of attack. Mass flow requirements for the pneumatic system were found to scale with freestream density and speed rather than freestream dynamic pressure. Detailed measurements of the pressures buffeting the vertical tail were made and spatial variations in the buffeting frequency were found. The LEX fence was found to have a significant effect on the frequency distribution on the outboard surface of the vertical fin. In addition to the above measurements, an extensive set of data was acquired for the validation of computational fluid dynamics codes and for comparison with flight test and small-scale wind tunnel test results.

Meyn, Larry A.↗
NASA NTRS1956

The Interference Effects of a Body on the Spanwise Load Distributions of Two 45 Degree Sweptback Wings of Aspect Ratio 8.02 from Low-Speed Tests

Tests of two wing-body combinations have been conducted in the Langley 19-foot pressure tunnel at a Reynolds number of 4 x 10(exp 6) and a Mach number of 0.19 to determine the effects of the bodies on the wing span load distributions. The wings had 45 degrees sweepback of the quarter-chord line, aspect ratio 8.02, taper ratio 0.45, and incorporated 12-percent-thick airfoil sections streamwise. One wing was untwisted and uncambered whereas the second wing incorporated both twist and camber. Identical bodies of revolution, of 10:1 fineness ratio, having diameter-to-span ratios of 0.10, were mounted in mid-high-wing arrangements. The effects of wind incidence, wing fences, and flap deflection were determined for the plane uncambered wing. The addition of the body to the plane wing increased the exposed wing loading at a given lift coefficient as much as 10 percent with the body at 0 degrees incidence and 4 percent at 4 degrees incidence. The bending-moment coefficients at the wing-body juncture were increased about 2 percent with the body at 0 degrees incidence, whereas the increases were as much as 10 percent with the body at 4 degrees incidence. The spanwise load distributions due to the body on the plane wing as calculated by using a swept-wing method employing 19 spanwise lifting elements and control points generally showed satisfactory agreement with experiment. The spanwise load distributions due to body on the flapped plane wing and on the twisted and cambered wing were dissimilar to those obtained on the plane wing. Neither of the methods of calculation which were employed yielded distributions that agreed consistently with experiment for either the flapped plane wing or the twisted and cambered wing.

Martina, Albert P.↗
NASA NTRS1993

Deep Skirt Would Confine Oil Spilled In Water

Skirt constitutes floating fence facilitating recovery. Includes panels joined to rods, which holds panels vertical. Skirt deployed from small ship. Ship pays out skirt while moving in circle from anchored end; then join ends, forming loop around oilspill.

Weinstein, Leonard M.↗
NASA NTRS1992

Brush seal leakage performance with gaseous working fluids at static and low rotor speed conditions

The leakage performance of a brush seal with gaseous working fluids at static and low rotor speed conditions was studied. The leakage results included for air, helium, and carbon dioxide at several bristle/rotor interferences. Also, the effects of packing a lubricant into the bristles and also of reversing the pressure drop across the seal were studied. Results were compared to that of an annular seal at similar operating conditions. In order to generalize the results, they were correlated using corresponding state theory. The brush seal tested had a bore diameter of 3.792 cm (1.4930 in.), a fence height of 0.0635 cm (0.025 in.), and 1800 bristles/cm circumference (4500 bristles/in. circumference). Various bristle/rotor radial interferences were achieved by using a tapered rotor. The brush seal reduced the leakage in comparison to the annular seal, up to 9.5 times. Reversing the pressure drop across the brush seal produced leakage rates approximately the same as that of the annular seal. Addition of a lubricant reduced the leakage by 2.5 times. The air and carbon dioxide data were successfully correlated using corresponding state theory. However, the helium data followed a different curve than the air and carbon dioxide data.

Carlile, Julie A.↗
NASA NTRS1953

Study of secondary-flow patterns in an annular cascade of turbine nozzle blades with vortex design

In order to increase understanding of the origin of losses in a turbine, the secondary-flow components in the boundary layers and the blade wakes of an annular cascade of turbine nozzle blades (vortex design) was investigated. A detailed study was made of the total-pressure contours and, particularly, of the inner-wall loss cores downstream of the blades. The inner-wall loss core associated with a blade of the turbine-nozzle cascade is largely the accumulation of low-momentum fluids originating elsewhere in the cascade. This accumulation is effected by a secondary-flow mechanism which acts to transport the low-momentum fluids across the channels on the walls and radially in the blade wakes and boundary layers. The patterns of secondary flow were determined by use of hydrogen sulfide traces, paint, flow fences, and total pressure surveys. At one flow condition investigated, the radial transport of low-momentum fluid in the blade wake and on the suction surface near the trailing edge accounted for 65 percent of the loss core; 30 percent resulted from flow in the thickened boundary layer on the suction surface and 35 percent from flow in the blade wake.

FLOW, SUBSONIC↗
NASA NTRS1948

Longitudinal-stability Investigation of High-lift and Stall-control Devices on a 52 Degree Sweptback Wing with and Without Fuselage and Horizontal Tail at a Reynolds Number of 6.8 x 10(exp 6).

Contains low-speed longitudinal stability characteristics of a 52 degree sweptback wing of aspect ratio 2.88, taper ratio 0.625, and NACA 64 (sub 1)-112 airfoil sections normal to the 0.282-chord line, in combination with split flaps, leading-edge flaps, and upper-surface fences. Low-wing and midwing-fuselage aerodynamic characteristics are presented with and without a horizontal tail at various vertical locations. Tests were conducted at a Reynolds number of 6.8 x 10(exp 6).

STABILITY, LONGITUDINAL - STATIC↗
NASA NTRS1953

A study of the use of leading-edge notches as a means for improving the low-speed pitching-moment characteristics of a thin 45-degree swept wing of aspect ratio 4

In an effort to develop a simple but effective means for controlling the stall progression of swept wings, a low-speed investigation has been undertaken primarily to determine the effectiveness of leading-edge notches. The investigation included consideration of notch size, location, and shape, as well as combined effects of notch—chord-extension and notch-fence arrangements. The wing used in the study had 45° quarter-chord sweep, aspect ratio 4, taper ratio 0.3, and NACA 65A006 airfoil sections streamwise. The results of the investigation indicated that although substantial improvements were obtained in the wing pitching-moment characteristics at moderate angles of attack, by use of outboard leading-edge notches, none of these notches produced desirable wing stability characteristics throughout the angle-of-attack range. The wing pitching-moment characteristics were relatively insensitive to notch size and to small changes in span-wise location. The use of a notch at the inboard end of a chord-extension increased the effectiveness of the chord-extension near stall and produced the same results as a chord-extension having an equivalent inboard overhang. Small localized notch—chord-extension combinations were found to produce the same pitching-moment characteristics as much larger chord-extension configurations. A leading-edge root cutout used in conjunction with a small outboard notch—chord-extension combination resulted in fairly desirable overall wing pitching-moment characteristics.

Joseph Weil↗
NASA NTRS1948

Wind-tunnel Investigation of High-lift and Stall-control Devices on a 37 Degree Sweptback Wing of Aspect Ratio 6 at High Reynolds Numbers

Results are presented of an investigation in the Langley 19-foot pressure tunnel of the longitudinal characteristics of a semispan model wing having 37 degrees sweepback of the leading edge, an aspect ratio of 6, and NACA 641-212 airfoil section perpendicular to the 27-percent-chord line. Several types of stall-control devices including extensible round-nose leading-edge flaps, a leading-edge slat, and a drooped leading edge were investigated; partial- and full-span trailing-edge split and double slotted flaps were also tested. In addition, various combinations of the aforementioned leading- and trailing-edge flaps were investigated. The tests covered a range of Reynolds numbers between 2.00 x 10(6) and 9.35 x 10(6). The wing with or without trailing-edge splity of double slotted flap was longitudinally unstable near maximum lift due to tip stalling. The addition of an outboard half-span leading-edge flap or a leading-edge slat to the plain wing or wing with inboard half-span split flaps eliminated tip stalling and resulted in stable moment variations at the stall. The drooped leading edge, on the other hand, was only effective when used in conjunction with an upper-surface fence. The combination of an outboard leading-edge device and inboard half-span double slotted flap resulted in an undesirable loop in the pitching-moment curve near maximum lift in spite of an inboard stall. The loop is attributed to the section characteristics of the double slotted flap. Air-flow surveys behind the wing indicated that a suitably placed horizontal tail would eliminate the loop in the moment curve.

Koven, William↗
NASA NTRS1994

Some metallographic results for brush bristles and brush segments of a shroud ring brush seal tested in a T-700 engine

Post-test investigation of a T-700 engine brush seal found regions void of bristles ('yanked out'), regions of bent-over bristles near the inlet, some 'snapped' bristles near the fence, and a more uniform smeared bristle interface between the first and last axial rows of bristles. Several bristles and four brush segments were cut from the brush seal, wax mounted, polished, and analyzed. Metallographic analysis of the bristle near the rub tip showed tungsten-rich phases uniformly distributed throughout the bristle, no apparent change within 1 mu m of the interface, and possibly a small amount of titanium, which would represent a transfer from the rotor. Analysis of the bristle wear face showed nonuniform tungsten, which is indicative of material resolidification. The cut end contained oxides and internal fractures; the worn end was covered with oxide scale. Material losses due to wear and elastoplastic deformation within the shear zone and third-body lubrication effects in the contact zone are discussed.

Hendricks, Robert C.↗