Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “favorability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

SRB seawater corrosion project

The corrosion behavior of 2219 aluminum when exposed to seawater was characterized. Controlled corrosion experiments at three different temperatures (30, 60 and 100 C) and two different environments (seawater and 3.5 percent salt solution) were designed to elucidate the initial stages in the corrosion process. It was found that 2219 aluminum is an active catalytic surface for growth of Al2O3, NaCl, and MgO. Formation of Al2O3 is favored at lower temperatures, while MgO is favored at higher temperatures. Visible corrosion products are formed within 30 minutes after seawater exposure. Corrosion characteristics in 3.5 percent salt solution are different than corrosion in seawater. Techniques utilized were: (1) scanning electron microscopy, (2) energy dispersive x-ray spectroscopy, and (3) Auger electron spectroscopy.

Bozack, M. J.↗
NASA NTRS1991

Navier-Stokes simulation of a close-coupled canard-wing-body configuration

The thin-layer Navier-Stokes equations are solved for the flow about a coplanar close-coupled canard-wing-body configuration at a transonic Mach number of 0.90 and at angles of attack ranging from 0 to 12 degrees. The influence of the canard on the wing flowfield, including canard-wing vortex interaction and wing vortex breakdown, is investigated. A study of canard downwash and canard leading-edge vortex effects, which are the primary mechanisms of the canard-wing interaction, is emphasized. Comparisons between the computations and experimental measurements of surface pressure coefficients, lift, drag and pitching moment data are favorable. A grid refinement study for configurations with and without canard shows that accurate results are obtained using a refined grid for angles of attack where vortex burst is present. At an angle of attack of approximately 12 deg, favorable canard-wing interaction which delays wing vortex breakdown is indicated by the computations and is in good agreement with experimental findings.

Tu, Eugene L.↗
NASA NTRS1991

Climatological perspectives, oceanographic and meteorological, on variability in the subtropical convergence zone in the northwestern Atlantic

The large-scale climatological environment of the Frontal Air-Sea Interaction Experiment (FASINEX) is described, with emphasis on the largest scales. Both long-term and annual sea surface temperature (SST) variability is discussed; a climatology of the west-central North Atlantic, derived from various sets of data obtained during the intensive phases of January-March, is presented, and the meteorological and oceanographic context for FASINEX is thus established. Surface marine observations and SST variability are discussed, and the marine meteorology of the FASINEX area is examined in terms of the surface pressure and winds, the sea-air temperature difference, and the cloud cover. Near 28 deg N in February is found to be a favorable time and place to observe large mean temperature gradients and downward Ekman pumping. The large-scale processes that set up the favorable environment for frontal activity are not limited to the winter months.

Hanson, Howard P.↗
NASA NTRS1989

Effect of abrupt pressure gradients on the structure of turbulent boundary layers

The structure of a turbulent boundary layer due to abruptly applied strong favorable and adverse pressure gradients, leading to relaminarization and separation, respectively, is considered. Digital image enhancement techniques have been applied to laser light sheet smoke flow visualization pictures. A 'local range modification' technique has been used to extract structural details otherwise lying ill-defined in the fully turbulent core. The cross-stream sections immediately prior to separation, and particularly those shortly after the application of the favorable pressure gradient, are vividly organized; there exists a criss-cross pattern in the spanwise plane with a mean orientation at about +/- 45 deg to the vertical.

Bandyopadhyay, Promode R.↗
NASA NTRS1991

The first ANDES elements: 9-DOF plate bending triangles

New elements are derived to validate and assess the assumed natural deviatoric strain (ANDES) formulation. This is a brand new variant of the assumed natural strain (ANS) formulation of finite elements, which has recently attracted attention as an effective method for constructing high-performance elements for linear and nonlinear analysis. The ANDES formulation is based on an extended parametrized variational principle developed in recent publications. The key concept is that only the deviatoric part of the strains is assumed over the element whereas the mean strain part is discarded in favor of a constant stress assumption. Unlike conventional ANS elements, ANDES elements satisfy the individual element test (a stringent form of the patch test) a priori while retaining the favorable distortion-insensitivity properties of ANS elements. The first application of this formulation is the development of several Kirchhoff plate bending triangular elements with the standard nine degrees of freedom. Linear curvature variations are sampled along the three sides with the corners as gage reading points. These sample values are interpolated over the triangle using three schemes. Two schemes merge back to conventional ANS elements, one being identical to the Discrete Kirchhoff Triangle (DKT), whereas the third one produces two new ANDES elements. Numerical experiments indicate that one of the ANDES element is relatively insensitive to distortion compared to previously derived high-performance plate-bending elements, while retaining accuracy for nondistorted elements.

Militello, Carmelo↗
NASA NTRS1991

Product and rate determinations with chemically activated nucleotides in the presence of various prebiotic materials, including other mono- and polynucleotides

We are investigating the reactions of ImpN's in the presence of a number of prebiotically plausible materials, such as metal ions, phosphate, amines and other nucleotides and hope to learn more about the stability/reactivity of ImpN's in a prebiotic aqueous environment. We find that, in the presence of phosphate, ImpN's form substantial amounts of diphosphate nucleotides. These diphosphate nucleotides are not very good substrates for template directed reactions, but are chemically activated and are known to revert to the phosphoimidazolides in the presence of imidazole under solid state conditions. With respect to our studies of the oligomerization reaction, the determination of the dimerization rate constant of a specific ImpN (guanosine 5'-phospho 2 methylimidazolide) both in the absence and the presence of the template leads to the conclusion that at 37 C the dimerization is not template directed, although the subsequent polymerization steps are. In other words, this specific polynucleotide synthesizing system favors the elongation of oligonucleotides as compared with the formation of dimers and trimers. This favoring of the synthesis of long as opposed to short oligonucleotides may be regarded as a rudimentary example of natural selection at the molecular level.

Kanavarioti, A.↗
NASA NTRS1992

A study of transonic aerodynamic analysis methods for use with a hypersonic aircraft synthesis code

A means of performing routine transonic lift, drag, and moment analyses on hypersonic all-body and wing-body configurations were studied. The analysis method is to be used in conjunction with the Hypersonic Vehicle Optimization Code (HAVOC). A review of existing techniques is presented, after which three methods, chosen to represent a spectrum of capabilities, are tested and the results are compared with experimental data. The three methods consist of a wave drag code, a full potential code, and a Navier-Stokes code. The wave drag code, representing the empirical approach, has very fast CPU times, but very limited and sporadic results. The full potential code provides results which compare favorably to the wind tunnel data, but with a dramatic increase in computational time. Even more extreme is the Navier-Stokes code, which provides the most favorable and complete results, but with a very large turnaround time. The full potential code, TRANAIR, is used for additional analyses, because of the superior results it can provide over empirical and semi-empirical methods, and because of its automated grid generation. TRANAIR analyses include an all body hypersonic cruise configuration and an oblique flying wing supersonic transport.

Sandlin, Doral R.↗
NASA NTRS1992

Interplanetary meteoroid debris in LDEF metal craters

The extraterrestrial meteoroid residue found lining craters in the Long Duration Exposure Facility (LDEF) aluminum and gold targets is highly variable in both quantity and type. In typical craters only a minor amount of residue is found and for these craters it is evident that most of the impacting projectile was ejected during crater formation. Less than 10 percent of the craters greater than 100 microns contain abundant residue consistent with survival of a major fraction of the projectile. In these cases the residue can be seen optically as a dark liner and it can easily be analyzed by SEM-EDX techniques. Because they are rare, the craters with abundant residue must be a biased sampling of the meteoroids reaching the earth. Factors that favor residue retention are low impact velocity and material properties such as high melting point. In general, the SEM-EDX observations of crater residues are consistent with the properties of chondritic meteorites and interplanetary dust particles collected in the stratosphere. Except for impacts by particles dominated by single minerals such as FeS and olivine, most of the residue compositions are in broad agreement with the major element compositions of chondrites. In most cases the residue is a thin liner on the crater floor and these craters are difficult to quantitatively analyze by EDX techniques because the electron beam excites both residue and underlying metal substrate. In favorable cases, the liner is thick and composed of vesicular glass with imbedded FeNi, sulfide and silicate grains. In the best cases of meteoroid preservation, the crater is lined with large numbers of unmelted mineral grains. The projectiles fragmented into micron sized pieces but the fragments survived without melting. In one case, the grains contain linear defects that appear to be solar flare tracks. Solar flare tracks are common properties of small interplanetary particles and their preservation during impact implies that the fragments were not heated above 600 C. We are investigating the meteoroid fragments in LDEF metal craters to determine the properties of interplanetary dust and to determine if there are meteoroid types that are overlooked or otherwise undetected in cosmic dust collections obtained from the stratosphere and polar ice.

Brownlee, D. E.↗
NASA NTRS1992

Aircraft Drag Reduction

This paper reviews aerodynamic drag reduction for friction, wave and vortex drag associated with supersonic cruise aircraft and suggests approaches and research directions which cover the spectrum from possibly significant to revolutionary. Various synergisms are also included, especially in regard to suction laminar flow control and flow separation control at cruise. The former may also enable improved low speed, high lift systems, lift to drag ratio for subsonic cruise, reduced parasitic viscous drag for favorable interference wave drag reduction approaches, and turbulent skin friction reduction via slot injection. Flow separation control at cruise proffers opportunities for increased leading edge thrust, increased lift increment from upper surface, increased fuselage lift/camber for wave drag due to lift reduction, improved performance of various favorable interference wave drag reduction schemes, as well as possibly better low speed, high-schemes and wing cruise performance. More speculative approaches include multi-stage aircraft, thrust vectoring for lift augmentation, as well as trim, and a number of conceptual wave and vortex drag reduction schemes.

D M Bushnell↗
NASA NTRS1992

The trade-off characteristics of acoustic and pressure sensors for the NASP

Results of a trade study for the development of pressure and acoustic sensors for use on the National Aerospace Plane (NASP) are summarized. Pressure sensors are needed to operate to 100 psia; acoustic sensors are needed that can give meaningful information about a 200 dB sound pressure level (SPL) environment. Both sensors will have to operate from a high temperature of 2000 F down to absolute zero. The main conclusions of the study are the following: (1) Diaphragm materials limit minimum size and maximum frequency response attainable. (2) No transduction is available to meet all the NASP requirements with existing technology. (3) Capacitive sensors are large relative to the requirement, have limited resolution and frequency response due to noise, and cable length is limited to approximately 20 feet. (4) Eddy current sensors are large relative to the requirement and have limited cable lengths. (5) Fiber optic sensors provide the possibility for a small sensor, even though present developments do not exhibit that characteristic. The need to use sapphire at high temperature complicates the design. Present high temperature research sensors suffer from poor resolution. A significant development effort will be required to realize the potential of fiber optics. (6) Short-term development seems to favor eddy current techniques with the penalty of larger size and reduced dynamic range for acoustic sensors. (7) Long-term development may favor fiber optics with the penalties of cost, schedule, and uncertainty.

Winkler, Martin↗
NASA NTRS1992

Water and cheese from the lunar desert: Abundances and accessibility of H, C, and N on the Moon

The Moon has been underrated as a source of H, N, C, and other elements essential to support life and to provide fuel for rockets. There is enough of these elements in each cubic meter of typical lunar soil to provide a substantial lunch for two, if converted to edible forms. The average amount of C per square meter of the lunar surface to a depth of 2 m is some 35 percent of the average amount per square meter tied up in living organisms on Earth. The water equivalent of H in the upper 2 m of the regolith averages at least 1.3 million liters per square kilometer. Mining of H from a small fraction of the regolith would provide all the rocket fuel needed for thousands of years. These elements can be removed from the soil by heating it to high temperature. Some favor the unproven resources of Phobos, Deimos, or near-Earth asteroids instead of the Moon as a source of extraterrestrial material for use in space, or Mars over the Moon as a site for habitation, partly on the basis that the chemical elements needed for life support and propellant are readily abundant on those bodies, but not on the Moon. Well, the Moon is not as barren of H, C, and N as is commonly perceived. In fact, the elements needed for life support and for rocket fuel are plentiful there, although the ore grades are low. Furthermore, the proximity of the Moon and consequent lower cost of transportation and shorter trip and communication times favor that body as the logical site for early acquisition of resources and extraterrestrial living.

Haskin, L. A.↗
NASA NTRS1992

Sources of nitric oxide and nitrous oxide following wetting of dry soil

A study is presented which is aimed at distinguishing among autotrophic nitrification, denitrification, and abiological processes as sources of NO and N2O production following wetting of dry soil. To distinguish among these processes, combinations of treatments in laboratory incubations of soil were used which included varying soil water content, autoclaving, C2H2 inhibition, and NO2(-) addition. Biological sources of NO and N2O commenced within minutes of wetting dry soil. Acetylene inhibition revealed that emissions of NO were dependent on nitrification, although a combination of NO2(-) production by nitrifiers and abiological reduction of NO2(-) to NO is also possible. NO emissions exceeded N2O emissions, and nitrification was the dominant source of both gases when soil water was below field capacity. It is concluded that NO emissions appear to be more important when good soil aeration favors nitrification, whereas N2O emissions appear more important when elevated soil water favors denitrification.

Davidson, Eric A.↗
NASA NTRS1922

The choice of the speed of an airship

The favorable speed of an airship is chiefly determined by the condition of the consumption of the least amount of fuel per unit of traveled distance, although other conditions come into play. The resulting rules depend on the character of the wind and on the variability of the efficiency of the engine propeller units. This investigation resulted in the following rules. 1) Always keep the absolute course and steer at such an angle with reference to it as to neutralize the side wind. 2) In a strong contrary wind, take a speed one and one half times the velocity of the wind. 3) As a general rule, take the velocity of the wind and the velocity of the course component of the wind. Add them together if the wind has a contrary component, but subtract them from each other if the wind has a favorable component.

AIRSHIPS - SPEED↗
NASA NTRS1933

A study of factors affecting the steady spin of an airplane

Data from wind-tunnel tests on a model of the NY-1 airplane were used in a study of the effect on the steady spin of a number of factors considered to be important. The factors were of two classes, mass distribution effects and aerodynamic effects. The study indicated that mass extended along the longitudinal axis has no detrimental effect or is even slightly beneficial, mass extended along the lateral axis is detrimental if the airplane spins with the inner wing tip far down, and mass extended along the normal axis, if of considerable magnitude, has a strong favorable effect. The aerodynamic effects considered in terms of rolling, pitching, and yawing moments added to those for a conventional airplane showed that added stable rolling moment could contribute favorable effect on the spin only in decreasing the amount of inward sideslip required for equilibrium. Negative pitching moment of moderate magnitude has unfavorable effect on a high-angle-of-attack spin, and stable yawing moment has pronounced beneficial effect on the spin. Experimental data from various sources were available to verify nearly all the deductions resulting from the study of the curves. When these results were considered for the purpose of deciding upon the best means to be developed for controlling the spin, the yawing-moment equilibrium was found to offer the most promising field for research. The wing-cellule yawing moment, of which the shape of the chord-force curve is an approximate measure, should be made as small as possible in the unstable sense and the damping yawing moment of the tail should be made as large as possible. The most serious unfavorable effect on the damping yawing moment of the tail is the blanketing of the vertical surfaces by the other parts of the tail.

Scudder, Nathan F↗
NASA NTRS1939

Physical Properties of Synthetic Resin Materials

A study was made to determine the physical properties of synthetic resins having paper, canvas, and linen reinforcements, and of laminated wood impregnated with a resin varnish. The results show that commercial resins have moduli of elasticity that are too low for structural considerations. Nevertheless, there do exist plastics that have favorable mechanical properties and, with further development, it should be possible to produce resin products that compare favorably with the light-metal alloys. The results obtained from tests on Compound 1840, resin-impregnated wood, show that this material can stand on its own merit by virtue of a compressive strength four times that of the natural wood. This increase in compressive strength was accomplished with an increase of density to a value slightly below three times the normal value and corrected one of the most serious defects of the natural product.

Fishbein, Meyer↗
NASA NTRS1940

The aileron as an aid to recovery from the spin

As part of a general investigation by the NACA of factors that affect the spin, the use of the aileron as an aid to recovery from the spin was studied. Tests of 10 different models, covering a wide range of mass distribution, were made in the NACA free-spinning tunnel to determine the effects of a large downward deflection of the outboard aileron and of normal angular deflections of the ailerons upon recovery characteristics. The results indicate that the direction of aileron setting, with or against the spin, which will aid recovery from the spin depends upon the airplane weight distribution. For monoplanes and for biplanes with lower-wing ailerons, ailerons with the spin will be favorable when the weight is distributed chiefly along the fuselage (single-engine airplanes) and ailerons against the spin will be favorable when the weight is distributed chiefly along the wings (multi engine airplanes). Downward movement of the outboard aileron through a large angle will not always be effective in aiding recovery, the effectiveness of such a movement also being dependent upon the weight distribution of the airplane.

Neihouse, A I↗
NASA NTRS1955

Arrangement of fusiform bodies to reduce the wave drag at supersonic speeds

By means of linearized-body theory and reverse-flow theorems, the wave drag of a system of fusiform bodies at zero angle of attack and supersonic speeds is studied to determine the effect of varying the relative location of the component parts. The investigation is limited to two-body and three-body arrangements of Sears-Haack minimum-drag bodies. It is found that in certain arrangements the interference effects are beneficial, and may even result in the two or three-body system having no more wave drag than that of the principal body alone. The most favorable location appears to be one in which the maximum cross-section of the auxiliary body is slightly forward of the Mach cone from the tail of the main body. The least favorable is the region between the Mach cone from the nose and the forecone from the tail of the main body. (author)

Friedman, Morris D↗
NASA NTRS1933

Wind-tunnel research comparing lateral control devices, particularly at high angles of attack V : spoilers and ailerons on rectangular wings

This report covers the fifth of a series of systematic investigations in which lateral control devices are compared with particular reference to their effectiveness at high angles of attack. The present report deals with tests of spoilers and ordinary ailerons on rectangular Clark y wing models. In an effort to obtain satisfactory control throughout the entire angle-of-attack range that can be maintained in flight, various spoilers were tested in combination with two sizes of previously tested ordinary ailerons - one of average proportions and the other short and wide. In addition, one large spoiler was tested alone. It was found that when ailerons and spoilers are used together the full effect of both is not obtained if the spoilers are located directly in front of the ailerons. With the proper combination of spoiler and aileron, however, it is possible to obtain satisfactory rolling control up to high angles of attack (15 degrees to 20 degrees), together with favorable yawing moments and small control forces. A moderate amount of rolling control with favorable yawing moments and small control forces was obtained with the large spoiler alone.

Weick, Fred E↗