Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “enhanced conductivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Enhancement to the conductivity of surface transfer-doped (111) diamond through thermochemical surface etching

The use of a transition metal catalyzed thermochemical etching method for improving the carrier transport properties of the near-surface two-dimensional (2D) hole gas in surface transfer-doped hydrogen-terminated (111) diamond is demonstrated. Using Ni 0.8 Cr 0.2 films deposited and annealed to a temperature of 900 °C, with up to three etch cycles, preferential (111) surface etching produces large terraces exceeding 10 μm in size with a surface microroughness, σ 2 RMS λ, that is two orders of magnitude lower than for the pre-etched (111) surface. Magnetotransport measurements on hydrogen-terminated Hall bars engineered on the pre- and post-etched surfaces and rendered conductive by the adsorbed water layer formed on exposure to ambient conditions demonstrate that this etching causes an improvement in the hole mobility by an order of magnitude, resulting in a measured sheet resistivity of 1.04 kΩ/sq at a temperature of 4.2 K without gating.

42 ENGINEERING↗
NASA NTRS1990

12-crown-4 ether-assisted enhancement of ionic conductivity and interfacial kinetics in polyethylene oxide electrolytes

The electrical and electrochemical properties of thin films of polyethylene oxide electrolytes with and without 12-crown-4 ether (12Cr4) are studied as a function of temperature and in the frequency regime from 100 kHz to 0.1 Hz. These measurements were made on electrolytes containing LiCF3SO3, LiBF4, or LiClO4 salts. At a given temperature, the bulk conductivity for a particular salt depends on the 12Cr4 concentration, reaching a maximum for a ratio of 12Cr4 to Li of 0.003.

Nagasubramanian, G.↗
NASA NTRS2004

Chemical stability enhancement of lithium conducting solid electrolyte plates using sputtered LiPON thin film

Sputter deposition of LiPON films directly onto high Li+ conductivity solid electrolyte plates has been investigated as a means to minimize the reactivity of the plates to metallic Li. The LiPON films were shown to effectively passivate the plates in contact with metallic Li, in contrast to unpassivated plates that reacted immediately in contact with Li metal.

LiPON lithium metals electrolyte plates↗
NASA NTRS2009

Resonance-induced sensitivity enhancement method for conductivity sensors

Methods and systems for improving the sensitivity of a variety of conductivity sensing devices, in particular capacitively-coupled contactless conductivity detectors. A parallel inductor is added to the conductivity sensor. The sensor with the parallel inductor is operated at a resonant frequency of the equivalent circuit model. At the resonant frequency, parasitic capacitances that are either in series or in parallel with the conductance (and possibly a series resistance) is substantially removed from the equivalent circuit, leaving a purely resistive impedance. An appreciably higher sensor sensitivity results. Experimental verification shows that sensitivity improvements of the order of 10,000-fold are possible. Examples of detecting particulates with high precision by application of the apparatus and methods of operation are described.

Tai, Yu-Chong↗
DOE OSTI2025

Enhancing cathode composites with conductive alignment synergy for solid-state batteries

Enhancing transport and chemomechanical properties in cathode composites is crucial for the performance of solid-state batteries. Our study introduces the filler-aligned structured thick (FAST) electrode, which notably improves mechanical strength and ionic/electronic conductivity in solid composite cathodes. The FAST electrode incorporates vertically aligned nanoconducting carbon nanotubes within an ion-conducting polymer electrolyte, creating a low-tortuosity electron/ion transport path while strengthening the electrode’s structure. This design not only mitigates recrystallization of the polymer electrolyte but also establishes a densified local electric field distribution and accelerates the migration of lithium ions. The FAST electrode showcases outstanding electrochemical performance with lithium iron phosphate as the active material, achieving a high capacity of 148.2 milliampere hours per gram at 0.2 C over 100 cycles with substantial material loading (49.3 milligrams per square centimeter). This innovative electrode design marks a remarkable stride in addressing the challenges of solid-state lithium metal batteries.

Science & Technology - Other Topics↗
NASA NTRS2002

Robe Development for Electrical Conductivity Analysis in an Electron Gun Produced Helium Plasma

The use of magnetohydrodynamic (MHD) power conversion systems, potentially coupled with a fission power source, is currently being investigated as a driver for an advanced propulsion system, such as a plasma thruster. The efficiency of a MHD generator is strongly dependent on the electrical conductivity of the fluid that passes through the generator; power density increases as fluid conductivity increases. Although traditional MHD flows depend on thermal ionization to enhance the electrical conductivity, ionization due to nuclear interactions may achieve a comparable or improved conductivity enhancement while avoiding many of the limitations inherent to thermal ionization. Calculations suggest that nuclear-enhanced electrical conductivity increases as the neutron flux increases; conductivity of pure He-3 greater than 10 mho/m may be achievable if exposed to a flux greater than 10(exp 12) neutrons/cm2/s.) However, this remains to be demonstrated experimentally. An experimental facility has been constructed at the Propulsion Research Center at the NASA Marshall Space Flight Center, using helium as the test fluid. High energy electrons will be used to simulate the effects of neutron-induced ionization of helium gas to produce a plasma. These experiments will be focused on diagnosis of the plasma in a virtually static system; results will be applied to future tests with a MHD system. Initial experiments will utilize a 50 keV electron gun that can operate at up to a current of 200 micro A. Spreading the electron beam over a four inch diameter window results in an electron flux of 1.5x 10(exp 13) e/sq cm/s. The equivalent neutron flux that would produce the same ionization fraction in helium is 1x10(exp 12) n/sq cm/s. Experiments will simulate the neutron generated plasma modeled by Bitteker, which takes into account the products of thermal neutron absorption in He-3, and includes various ion species in estimating the conductivity of the resulting plasma. Several different probes will be designed and implemented to verify the plasma kinetics model. System parameters and estimated operating ranges are summarized. The predicted ionization fraction, electron density, and conductivity levels are provided in for an equivalent neutron flux of 1x10(exp 12) n/cm2/s. Understanding the complex plasma kinetics throughout a MHD channel is necessary to design an optimal power conversion system for space propulsion applications. The proposed experiments seek to fully characterize the helium plasma and to determine the reliability of each measurement technique, such that they may be applied to more advanced MHD studies. The expected value of each plasma parameter determined from theoretical models will be verified experimentally by several independent techniques to determine the most reliable method of obtaining each parameter. The results of these experiments will be presented in the final paper.

Bragg-Sitton, Shannon M.↗
DOE OSTI2023

Electronic transport in copper–graphene composites

In this work, we investigate electronic transport properties of copper–graphene (Cu–G) composites using a density-functional theory (DFT) framework. Conduction in composites is studied by varying the interfacial distance of copper/graphene/copper (Cu/G/Cu) interface models. Electronic conductivity of the models computed using the Kubo–Greenwood formula shows that the conductivity increases with decreasing Cu–G distance and saturates below a threshold Cu–G distance. The DFT-based Bader charge analysis indicates increasing charge transfer between Cu atoms at the interfacial layers and the graphene with decreasing Cu–G distance. The electronic density of states reveals increasing contributions from both copper and carbon atoms near the Fermi level with decreasing Cu–G interfacial distance. By computing the space-projected conductivity of the Cu/G/Cu models, we show that the graphene forms a bridge to the electronic conduction at small Cu–G distances, thereby enhancing the conductivity.

36 MATERIALS SCIENCE↗
NASA NTRS1984

Ambipolar diffusion in the middle atmosphere

In the middle atmosphere above 60 km, the electron concentration increases with altitude, reaching values of 10 to the 10th per cu m in the daytime ionospheric E region near 100 km. The electrons are more mobile than the ions and diffuse more rapidly through the neutral atmosphere. The electron diffusion polarizes the medium, causing an electric field to develop that acts to retard the electron diffusion and enhance the conduction current of ions. A global zonally averaged numerical model of atmosheric electricity from the ground to 100 km is used to examine the effect of ambipolar diffusion and the earth's geomagnetic field on the currents and fields in the middle atmosphere. The results show that above about 65 km, ambipolar diffusion generates local electric fields and conduction currents that balance electron diffusion currents. The electric fields and conduction currents are a few orders of magnitude larger than the vertical fields and currents calculated from the downward mapping of the ionospheric potential without taking electron diffusion into account. Ambipolar diffusion does not alter the total current flowing in the global circuit. It is a local effect where enhanced conduction currens flow to balance the electron diffusion current.

Tzur, I.↗
DOE OSTI2024

Aluminum Ultra-conductors for Energy-Efficient Aerospace Busbar Applications (Abstract)

In this project, we will develop aluminum ultra-conductors with graphene additives demonstrating enhanced electrical conductivity at 90 °C compared to electric grade aluminum alloy AA1100 (43% IACS at 90 °C). While ultra-conductivity has been developed in copper and copper alloys, it is yet to be reported extensively in aluminum-based materials. This project will scale initial work done at PNNL on aluminum ultra-conductors using shear-assisted processing and extrusion (ShAPETM), a novel solid phase processing technique. Ultra-conductors are an emerging class of composites, comprised of a metal substrate with small quantities of nanocrystalline additives such as graphene or carbon nanotubes that demonstrate enhanced conductivity at relevant operating temperatures. Aluminum ultra-conductors can improve efficiency and power density while reducing the demand for copper in a wide range of applications, such as power transmission cables and electric motors. Busbars are an important component in aerospace systems that require lightweight and high-current power distribution including both future electric vertical take-off and landing (eVTOL) aircrafts and current aircraft electrical systems. We will accelerate aluminum ultra-conductor composite formulation development using combinatorial synthesis and testing methods aided by process/microstructure modeling, developed previously at PNNL. Eaton will test the properties of the ShAPE aluminum ultra-conductor feedstock (used to make the busbars) in relevant operating conditions (20 – 90 °C), predict the improvement in busbar performance when manufactured with ultra-conductors over commercial conductors (such as AA1100), and perform technoeconomic analysis to evaluate the potential for commercialization of ShAPE aluminum ultra-conductors. The project is expected to have a budget of $\$375$K, with $\$300$K in federal funding and $\$75$K in-kind cost-share contribution from Eaton over a period of performance of 24 months. Of the $\$300$K of federal funds, $\$140$K is allocated for CRADA activities that generate intellectual property (IP), and the remaining $\$160$K is reserved for modeling, material testing, characterization, travel, and reporting-related activities.

36 MATERIALS SCIENCE↗
NASA NTRS1972

Residual conductivity in unannealed amorphous germanium.

An enhanced residual conductivity which persists long after cessation of illumination has been observed in amorphous germanium at 77 K. The effect may be thermally quenched by heating to 120 K, returning the sample to its initial condition.

Burke, T. J.↗
DOE OSTI2025

Scaling behavior and giant field enhancement of the thermal conductivity in the honeycomb antiferromagnet BaCo 2⁢ (AsO 4 ) 2

The layered honeycomb material BaCo 2 (AsO 4 ) 2 is of topical interest because its magnetic state is related to that of the Kitaev magnet α-RuCl 3 . Using thermal transport to probe how magnetic excitations interact with phonons in the magnetically disordered regime, we have uncovered an unusually large enhancement of the thermal conductivity κ xx in an in-plane magnetic field H. Just above the Néel temperature T N , a field of 13 T increases κ xx by a factor of ∼ 211, which is very large compared to other magnetic insulators. Interestingly, κ xx (H, T) exhibits a scaling behavior in the entire magnetically disordered region that surrounds the ordered zigzag state. The ratio Δκ xx (H, T)/κ xx (13, T), measured throughout the disordered region, collapses to a one-parameter scaling function exp(−1/gx) (where x = μ B B/k B T and g is a constant).

36 MATERIALS SCIENCE↗
NASA NTRS1981

Ionic conductivity and thermoelectric power of pure and Al2O3-dispersed AgI

Ionic and electronic conductivities, and thermoelectric power have been measured for AgI and AgI containing a dispersion of submicron size Al2O3 particles. While the dispersion of Al2O3 enhances the ionic conductivity significantly, it does not affect the electronic properties of the matrix. The enhancement is a strong function of the size and concentration of the dispersoid. Various models have been tested to account for the enhanced conduction. However, the complex behavior of the present results points out the need for more sophisticated theoretical models. Ionic conduction and thermoelectric power data suggest that the dispersed Al2O3 generates an excess of cation vacancies and thereby enhances the conductivity and suppresses the thermoelectric power of the matrix. The individual heats of transport of cation interstitials and vacancies have been estimated and compared to their respective migration energies.

Shahi, K.↗
NASA NTRS1996

Electrically conductive polyimides containing silver trifluoroacetylacetonate

Polyimides with enhanced electrical conductivity are produced by adding a silver ion-containing additive to the polyamic acid resin formed by the condensation of an aromatic dianhydride with an aromatic diamine. After thermal treatment the resulting polyimides had surface conductivities in the range of 1.7.times.10.sup.-3 4.5 .OMEGA..sup.-1 making them useful in low the electronics industry as flexible, electrically conductive polymeric films and coatings.

Rancourt, James D.↗
DOE OSTI2025

Enhancing surface activity and durability in triple conducting electrode for protonic ceramic electrochemical cells

With the material system operating at lower temperatures, protonic ceramic electrochemical cells (PCECs) can offer high energy efficiency and reliable performance for both power generation and hydrogen production, making them a promising technology for reversible energy cycling. However, PCEC faces technical challenges, particularly regarding electrode activity and durability under high current density operations. To address these challenges, we introduce a nano-architecture oxygen electrode characterized by high porosity and triple conductivity, designed to enhance catalytic activity and interfacial stability through a self-assembly approach, while maintaining scalability. Electrochemical cells incorporating this advanced electrode demonstrate robust performance, achieving a peak power density of 1.50 W cm −2 at 600 °C in fuel cell mode and a current density of 5.04 A cm −2 at 1.60 V in electrolysis mode, with enhanced stability on transient operations and thermal cycles. The underlying mechanisms are closely related to the improved surface activity and mass transfer due to the dual features of the electrode structure. Additionally, the enhanced interfacial bonding between the oxygen electrode and electrolyte contributes to increased durability and thermomechanical integrity. This study underscores the critical importance of optimizing electrode microstructure to achieve a balance between surface activity and durability.

Protonic Ceramic Electrochemical Cells↗
DOE OSTI2020

A Low-Cost Iron-Based Current Collector for Alkaline Battery Electrodes

The use of three-dimensional porous nickel foam as the current collector of the nickel hydroxide electrode adds significantly to the cost of the nickel-based alkaline rechargeable batteries. Although iron is considerably less expensive than nickel, iron corrodes at the operating potential of the nickel hydroxide electrode. We have found that a 70–100 nm thick thermal coating of cobalt ferrite spinel protects the iron from corrosion. Such a coated iron substrate was found to be stable against corrosion even when polarized anodically at 10 mA cm -2 in 30% potassium hydroxide electrolyte for 1000 h. While the thermal coating of cobalt ferrite protected iron against corrosion, incorporation of lithium ions into the coating was found to enhance the electrical conductivity of the coating. XPS and EXAFS studies confirmed that the enhanced conductivity resulted from an increase in the population of Co 3+ in the ferrite spinel lattice. An inexpensive iron (steel) substrate protected by such a coating when used as a nickel hydroxide battery electrode exhibited a specific capacity of 0.25 Ah g -1 at C/5 discharge rate, comparable to a nickel hydroxide electrode based on a relatively expensive nickel foam substrate. The steel-based electrode also exhibited no noticeable degradation over 150 cycles at C/2 rate. This demonstration of a robust and economical steel substrate presents a unique opportunity for reducing the cost of the nickel hydroxide battery electrode in alkaline batteries

25 ENERGY STORAGE↗
DOE OSTI2021

Polymer-ceramic composite electrolytes for all-solid-state lithium batteries: Ionic conductivity and chemical interaction enhanced by oxygen vacancy in ceramic nanofibers

Perovskite Li 3x La 2/3-x TiO3 (LLTO) nanofibers have been heat-treated in the hydrogen-containing atmosphere and then incorporated with the poly(vinylidene fluoride)-co-hexafluoropropylene (PVDF-HFP) polymer to form a composite electrolyte. Hydrogen treatment has created oxygen vacancies in the LLTO nanofibers, which has reduced the activation energy of Li ion transport along intra-grains and inter-grains, leading to improvement in the ion conductivity of LLTO nanofibers. Hydrogen treatment of the LLTO nanofibers has also enhanced the chemical interaction between the LLTO nanofibers and the polymer matrix in the composite electrolyte, and favored the Li ion transport at the nanofiber/polymer interface, improving the ion conductivity of the composite electrolyte to 3.4×10- 4 S/cm at room temperature. As a result, the Li|composite-electrolyte|Li half-cell exhibits good stability during lithium plating/stripping cycling at room temperature, showing an overpotential of ~91 mV at a constant current density of 0.5 mA/cm 2 . Finally, the full-cell battery with the composite electrolyte, lithium metal anode and lithium iron phosphate cathode shows excellent rate capacity and cycling performance.

25 ENERGY STORAGE↗
DOE OSTI2021

Conducting thermal energy to the membrane/water interface for the enhanced desalination of hypersaline brines using membrane distillation

Membrane distillation (MD) is a membrane-based thermal desalination process capable of treating hypersaline brines. Standard MD systems rely on preheating the feed to drive the desalination process. However, relying on the feed to carry thermal energy is limited by a decline of the thermal driving force as the water moves across the membrane, and temperature polarization. In contrast, supplying heat directly into the feed channel, either through the membrane or other channel surfaces, has the potential of minimizing temperature polarization, increasing single-pass water recoveries, and decreasing the number of heat exchangers in the system. When solar thermal energy can be utilized, particularly if the solar heat is optimally delivered to enhance water evaporation and process performance, MD processes can potentially be improved in terms of energy efficiency, environmental sustainability, or operating costs. Here we describe an MD process using layered composite membranes that include a high-thermal-conductivity layer for supplying heat directly to the membrane-water interface and the flow channel. Here, the MD system showed stable performance with water flux up to 9 L/m 2 /hr, and salt rejection >99.9% over hours of desalinating hypersaline feed (100 g/L NaCl). In addition to bench-scale system, we developed a computational fluid dynamics model that successfully described the transport phenomena in the system.

42 ENGINEERING↗