Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “elastomers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Implementation of Statistical Process Control: Evaluating the Mechanical Performance of a Candidate Silicone Elastomer Docking Seal

The National Aeronautics and Space Administration has been developing a novel docking system to meet the requirements of future exploration missions to low-Earth orbit and beyond. A dynamic gas pressure seal is located at the main interface between the active and passive mating components of the new docking system. This seal is designed to operate in the harsh space environment, but is also to perform within strict loading requirements while maintaining an acceptable level of leak rate. In this study, a candidate silicone elastomer seal was designed, and multiple subscale test articles were manufactured for evaluation purposes. The force required to fully compress each test article at room temperature was quantified and found to be below the maximum allowable load for the docking system. However, a significant amount of scatter was observed in the test results. Due to the stochastic nature of the mechanical performance of this candidate docking seal, a statistical process control technique was implemented to isolate unusual compression behavior from typical mechanical performance. The results of this statistical analysis indicated a lack of process control, suggesting a variation in the manufacturing phase of the process. Further investigation revealed that changes in the manufacturing molding process had occurred which may have influenced the mechanical performance of the seal. This knowledge improves the chance of this and future space seals to satisfy or exceed design specifications.

docking seal↗
DOE OSTI2023

Investigation of the structure, filler interaction and degradation of disulfide elastomers made by Reversible Radical Recombination Polymerization (R3P)

In this paper we report the synthesis and analysis of cyclic polydisulfides, their redox depolymerization as well as their interaction with carbon black. Cyclic poly(3,6-dioxa-1,8-octanedithiol)s (pDODT) were synthesized by Reversible Radical Recombination Polymerization (R3P). R3P is a scalable “green” polymerization process using triethylamine (TEA), H 2 O 2 and air for the polymerization of dithiol monomers. pDODTs were synthesized in 5 and 20 g batches. The effect of peroxide concentration (3, 5, 10, 20, 30%) was investigated. It was found that the molecular weights increased exponentially with increasing peroxide concentrations. At 30% peroxide concentration pDODTs with M n up to 400,000 g/mol and polydispersity of 2 were obtained. 700 and 800 MHz NMR were used for investigating the chemical structure of the polymers. The absence of thiol end group signals in polymers made with > 10wt % H 2 O 2 and M n < 100,000 g/mol, including a sample of a fractionated polymer with starting Mn = 600,000 g/mol, verified cyclic structures. Dithiothreitol reduced the polymers to monomer and a small percentage of oligomers. Carbon black was shown to increase the moduli of high molecular weight pDODTs. Swelling tests in chloroform showed that polymers made with 20 and 30w% peroxide swelled 14 and 10 times of their starting weight without dissolving, indicating chemical interaction between the polymers and carbon black. In conclusion, further analysis of these interesting elastomers, available at the 20 g scale, is in progress.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

A Physically-Based Model for Thermo-Oxidative and Hydrolytic Aging of Elastomers

A computationally efficient model is proposed to capture the loss of mechanical performance due to chemical aging that are formed as the competition of chain scission and cross-link formation/dissolution, such as thermo-oxidative aging or hydrolytic aging. The model should be considered an extension of our recent models [1, 2, 3] which further simplifies the matrix behavior based on the assumption of independence of environmental and mechanical damage. The model uses this assumption to reduce the necessary material parameters needed to model constitutive and inelastic behavior of elastomers during aging. To this end, the model can provide accurate predictions of the material performance with the significantly fewer number of fitting parameters. The model is relevant for all decay mechanisms formed by the occurrence of two simultaneous micro-mechanisms; (i) formation/reduction of the cross-links, and (ii) chain scission, both of which are present in thermo-oxidation and hydrolytic aging. Assuming the alteration of the chain density along the aging trajectory is identical to the peroxide cross-link density for thermo-oxidation, and the change of the average molecular weight for hydrolysis, the strain energy of polymer matrix can be rewritten as a function of deformation, deformation history, storage time and aging temperature. Next, the modified network alteration model is formulated for implementation into Finite Element (FE) simulations. The model is built on the presumption of homogeneous and consistent oxygen/water absorption and thus is mainly relevant for relatively thin samples exposed to environmental loads for a long time. The proposed model includes only six physically inspired material parameters. Therefore, while it is computationally efficient, it shows good agreement with own experimental data, which performed on various range of accelerated aging temperatures and times. With respect to its computational efficiency, simplicity, accuracy, and interpret-ability, the model is the right choice for advanced implementations in FE programs.

42 ENGINEERING↗
DOE OSTI2022

A physics-informed multi-agents model to predict thermo-oxidative/hydrolytic aging of elastomers

This paper introduces a novel physics-informed multi-agents constitutive model to propose prediction in quasi-static constitutive behavior of cross-linked elastomer and the loss of mechanical performance during environmental aging. The presented model is used to simulate the effect of single-mechanism chemical aging (i.e. thermal-inducedor hydrolytic aging) on the behavior of the material in this hybrid framework. Those environmental single-mechanism damages change the polymer matrix over time due to massive chain scission, chain formations, and changing the arrangement of molecules in the polymer matrix. Here we propose a data-driven super-constrained machine-learned engine to represent damage in the polymer matrix and capture the changes in material behavior, including its inelastic features such as Mullins effect and permanent set in the course of aging. We have simplified the 3D stress–strain tensor mapping problem into a small number of super-constrained 1D mapping problems by means of a sequential order reduction. An assembly of multiple replicated conditional neural-network learning-agents (L-agents) is trained to systematically simplify the high-dimensional mapping problem into multiple 1D problems, each represented by a different type of agent. Our hybrid framework is designed to capture the effect of deformation history, aging time, and aging temperature. The model is validated with respect to a comprehensive set of experiments specifically designed to benchmark model capabilities and also against available data in the literature. Thermodynamic consistency and frame independency have been verified. Besides acceptable predictive abilities, a significant reduction of computational cost to predict behavior at multiple states of deformation is the most significant feature of this model.

42 ENGINEERING↗
DOE OSTI2021

Direct comparison of gamma, electron beam and X-ray irradiation doses on characteristics of low-density polyethylene, polypropylene homopolymer, polyolefin elastomer and chlorobutyl rubber medical device polymers

There is a growing need for increased efficiency in the sterilization of single use medical devices and other products that contain polymer components. Gamma radiation is widely used for devices suited for radiation sterilization; however, safety, throughput and cobalt-60 source availability are challenging the prospect of relying on gamma radiation to meet the anticipated needs of the industry. Use of electron beam (e-beam) and X-rays as alternatives to gamma for radiation sterilization have been hampered in part by a concern that these modalities may adversely affect polymer integrity and performance relative to the gamma method, for which the industry has had much more experience. To address this concern, the effects of sterilization-relevant doses of ebeam, X-ray and gamma radiation were directly compared using common medical device polymers found in two prototypical commercial devices currently sterilized using cobalt-60 gamma irradiation. The Becton, Dickinson and Company (BD) Vacutainer™ Plus tube contains low-density polyethylene and chlorobutyl rubber components, while the BD Vacutainer™ Push Button Blood Collection Set contains polypropylene homopolymer and polyolefin elastomer components. Injection-molded samples prepared from the polymers used in these products were exposed to target doses of 15, 35, 50 and 80 kGy using gamma, e-beam and X-ray radiation. Changes in coloration, tensile properties and hardness were measured for each condition, and the effects of e-beam and X-ray irradiation compared with the effects of gamma irradiation on these properties. Both e-beam and X-ray appear as viable alternatives to gamma irradiation for sterilization of the polymers tested.

sterilization, gamma, X-ray, electron beam, radiat↗
DOE OSTI2021

Multiscale Structural Characterization of a Smectic Liquid Crystalline Elastomer upon Mechanical Deformation Using Neutron Scattering

Liquid crystalline elastomers (LCEs) exhibit unique shape memory behavior due to the combination of liquid crystalline orientation and rubber elasticity. Multiscale structural characterization of these materials upon deformation is crucial to understanding their structure–property relationships. In this work, the structure evolution of an epoxy-based, main-chain LCE with deuterated flexible spacers upon uniaxial mechanical deformation is investigated at different length scales. Wide-angle and small-angle X-ray scattering (WAXS/SAXS) reveal the presence of smectic polymorphism and rotations of the smectic domains upon mechanical stretching, which is also confirmed by small-angle neutron scattering (SANS). Importantly, the selective deuteration enables an improved neutron scattering contrast between the smectic and amorphous domains. SANS patterns of the deformed, deuterated LCE exhibit strong scattering streaks that are not observed in SAXS or SANS of hydrogenated LCE, indicating the presence of highly aligned amorphous domains. The macroscopic orientation also results in the formation of structures in the micrometer scale revealed by the ultrasmall-angle neutron scattering (USANS) experiment.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Asymmetric Miktoarm Star Polymers as Polyester Thermoplastic Elastomers

A library of polyester-based A(BA') n asymmetric miktoarm star polymers was synthesized with A, A' = poly(l-lactide) (PLLA) as the semicrystalline hard blocks and B = poly(4-methylcaprolactone) (PMCL) as the soft segment using a grafting-through platform known as μSTAR. The synthetic versatility of μSTAR enabled a systematic investigation of architectural design parameters, in particular the number of BA' arms (n), while holding the A, A', and B block lengths constant. The value of n has a pronounced impact on the mechanical properties of these high-molecular-weight miktoarm materials. Tensile toughness increases with n, an effect likely related to bridging, as the modulus drops because the hard-block volume fraction decreases. Furthermore, these insights expand our understanding of architecture effects in sustainable thermoplastic elastomers.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Exchangeable Liquid Crystalline Elastomers: Enabling Rapid Processing and Enhanced Actuation Stability through On-Demand Deactivation

Exchangeable liquid crystalline elastomers (xLCEs) bearing dynamic covalent bonds are promising candidates for soft actuators due to their unique capability to adjust both network structure and liquid crystalline (LC) alignment after polymerization. While current xLCEs with low exchange temperatures are convenient for processing, they suffer from issues such as creep and loss of LC alignment during repeated thermal actuation. Herein, we present an effective solution using dynamic anhydride chemistry within a thiol-ene-based xLCE. This approach enables a catalyst-free, low-temperature bond exchange of the xLCE after polymerization, allowing for the adjustment of LC orientation under mild conditions. More importantly, it enables on-demand deactivation of the bond exchange via anhydride hydrolysis, effectively eliminating creep and enhancing actuation stability for over 100 cycles. Furthermore, the hydrolysis process results in the formation of carboxylic acid groups, which can be converted into carboxylates via alkali treatment, thereby providing the xLCE with humidity responsiveness. Finally, these findings highlight the use of dynamic anhydride bonds in the fabrication and optimization of xLCEs with enhanced durability and functionality, which is expected to facilitate significant advancements in their applications in soft actuators and robotics.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Aligned Conjugated Polymer Nanofiber Networks in an Elastomer Matrix for High-Performance Printed Stretchable Electronics

Conjugated polymer films are promising in wearable X-ray detection. However, achieving optimal film microstructure possessing good electrical and detection performance under large deformation via scalable printing remains challenging. Herein, we report bar-coated high-performance stretchable films based on a conjugated polymer P(TDPP-Se) and elastomer SEBS blend by optimizing the solution-processing conditions. The moderate preaggregation in solution and prolonged growth dynamics from a solvent mixture with limited dissolving capacity is critical to forming aligned P(TDPP-Se) chains/crystalline nanofibers in the SEBS phase with enhanced π–π stacking for charge transport and stress dissipation. The film shows a large elongation at break of >400% and high mobilities of 5.29 cm 2 V –1 s –1 at 0% strain and 1.66 cm 2 V –1 s –1 over 500 stretch–release cycles at 50% strain, enabling good X-ray imaging with a high sensitivity of 1501.52 μC Gy air –1 cm –2 . Finally, our work provides a morphology control strategy toward high-performance conjugated polymer film-based stretchable electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Revealing Deformation Mechanisms in Polymer-Grafted Thermoplastic Elastomers via In Situ Small-Angle X-ray Scattering

The tunable properties of thermoplastic elastomers (TPEs), through polymer chemistry manipulations, enable these technologically critical materials to be employed in a broad range of applications. The need to “dial-in” the mechanical properties and responses of TPEs generally requires the design and synthesis of new macromolecules. In these designs, TPEs with nonlinear macromolecular architectures outperform the mechanical properties of their linear copolymer counterparts, but the differences in the deformation mechanism providing enhanced performance are unknown. Here, in situ small-angle X-ray scattering (SAXS) measurements during uniaxial extension reveal distinct deformation mechanisms between a commercially available linear poly(styrene)–poly(butadiene)–poly(styrene) (SBS) triblock copolymer and the grafted SBS version containing grafted poly(styrene) (PS) chains from the poly(butadiene) (PBD) midblock. The neat SBS (φ SBS = 100%) sample deforms congruently with the macroscopic dimensions, with the domain spacing between spheres increasing and decreasing along and transverse to the stretch direction, respectively. At high extensions, end segment pullout from the PS-rich domains is detected, which is indicated by a disordering of SBS. Conversely, the PS-grafted SBS that is 30 vol % SBS and 70% styrene (φ SBS = 30%) exhibits a lamellar morphology, and in situ SAXS measurements reveal an unexpected deformation mechanism. During deformation, there are two simultaneous processes: significant lamellar domain rearrangement to preferentially orient the lamellae planes parallel to the stretch direction and crazing. The samples whiten at high strains as expected for crazing, which corresponds with the emergence of features in the 2D SAXS pattern during stretching consistent with fibril-like structures that bridge the voids in crazes. The significant domain rearrangement in the grafted copolymers is attributed to the new junctions formed across multiple PS domains by the grafting of a single chain. In conclusion, the in situ SAXS measurements provide insights into the enhanced mechanical properties of grafted copolymers that arise through improved physical cross-linking that leads to nanostructure domain reorientation for self-reinforcement and craze formation where fibrils help to strengthen the polymer.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Elastomer Mechanics of Cross-Linked Linear-Ring Polymer Blends

Cross-linking a blend of linear and ring polymers creates a new topology-based dual-network elastomer in which the two components differ significantly in their topology. We use molecular simulations and topological analysis to examine key mechanical properties as functions of ring polymer volume fraction Φ R . For Φ R < Φ R *, where the rings begin to overlap, the network shear modulus G and the maximum stretch ratio λ p are weakly dependent on Φ R . For Φ R > Φ R *, entanglements trapped in the network are diluted as the rings overlap, leading to a significant decrease in G and an increase in λ p with increasing Φ R . Here, the peak tensile stress, σ p , exhibits a maximum around Φ R *, indicating an enhancement of network strength due to the stronger cohesion from the entanglements between linear and ring polymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Commodity Thermoplastic Elastomer-Enabled Templated Synthesis of Large-Pore Ordered Mesoporous Materials

Fabrication of ordered mesoporous materials (OMMs) has predominantly relied on templating-based methods. However, these methods are constrained by several limitations, especially the limited pore sizes attainable with commercially available surfactants used as structure-directing agents. To unlock the full potential of the OMMs, it is essential to develop synthetic strategies that facilitate the production of large-pore OMMs using scalable processes and cost-effective precursors. This work demonstrates the use of thermoplastic elastomer (TPE)-derived carbon replicas for synthesizing ordered mesoporous silica (OMS) and metal oxides (OMMOs) via precursor infiltration and template removal. The nanostructural evolution of the resulting inorganic materials was systematically investigated. Specifically, using tetraethyl orthosilicate (TEOS) as a silica precursor, this method can produce an OMS with relatively large pores. To establish the generalizability of this process, the fabrication approach was extended to other commercially available TPEs with varied chemical compositions and molecular weights while consistently resulting in ordered structures. Additionally, this synthetic strategy can be successfully applied to the production of OMMOs, including tin and titanium oxide matrix chemistries, yielding pore sizes of 16.0 and 19.2 nm, respectively. By developing a general method and using low-cost precursors, this work presents a scalable approach for fabricating large-pore OMMs with tunable pore textures and matrix chemistries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Direct synthesis of ordered mesoporous materials from thermoplastic elastomers

Abstract The ability to manufacture ordered mesoporous materials using low-cost precursors and scalable processes is essential for unlocking their enormous potential to enable advancement in nanotechnology. While templating-based methods play a central role in the development of mesoporous materials, several limitations exist in conventional system design, including cost, volatile solvent consumption, and attainable pore sizes from commercial templating agents. This work pioneers a new manufacturing platform for producing ordered mesoporous materials through direct pyrolysis of crosslinked thermoplastic elastomer-based block copolymers. Specifically, olefinic majority phases are selectively crosslinked through sulfonation reactions and subsequently converted to carbon, while the minority block can be decomposed to form ordered mesopores. We demonstrate that this process can be extended to different polymer precursors for synthesizing mesoporous polymer, carbon, and silica. Furthermore, the obtained carbons possess large mesopores, sulfur-doped carbon framework, with tailorable pore textures upon varying the precursor identities.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Alignment switching in 3D-printed smectic liquid crystal elastomers

Extrusion-based additive manufacturing has emerged as a powerful platform for designing shape-morphing materials through controlled orientation. However, existing approaches primarily rely on a single mode of flow-induced alignment, limiting orientation programmability. Herein, we present a direct-ink-writing approach for smectic liquid crystal elastics that exploits two distinct alignment modes within a single ink. The smectic ink exhibits shear- and temperature-dependent orientation switching, enabling molecular alignment either perpendicular or parallel to the print direction. Combined rheological, X-ray, and molecular dynamics analyses reveal that this alignment inversion arises from the preservation or collapse of smectic layers under flow. This reversible switching encodes both contractile and elongational actuation within individual filaments, greatly expanding the design freedom of printed liquid crystal elastomers. We demonstrate 2D and 3D structures with diverse programmed shape transformations, highlighting the potential of this platform for adaptive soft actuators and architected functional materials.

Lee, Jin Hyeong [Pusan National University, Busan,↗
DOE OSTI2022

On the mechanism of marine fouling-prevention performance of oil-containing silicone elastomers

For many decades, silicone elastomers with oil incorporated have served as fouling-release coating for marine applications. In a comprehensive study involving a series of laboratory-based marine fouling assays and extensive global field studies of up to 2-year duration, we compare polydimethylsiloxane (PDMS) coatings of the same composition loaded with oil via two different methods. One method used a traditional, one-pot pre-cure oil addition approach (o-PDMS) and another method used a newer post-cure infusion approach (i-PDMS). The latter displays a substantial improvement in biofouling prevention performance that exceeds established commercial silicone-based fouling-release coating standards. We interpret the differences in performance between one-pot and infused PDMS by developing a mechanistic model based on the Flory–Rehner theory of swollen polymer networks. Using this model, we propose that the chemical potential of the incorporated oil is a key consideration for the design of future fouling-release coatings, as the improved performance is driven by the formation and stabilization of an anti-adhesion oil overlayer on the polymer surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Mechanically tunable elastomer and cellulose nanocrystal composites as scaffolds for in vitro cell studies

Considering the range of properties that various materials offer for tissue engineering it has come clear that no one size fits all, as no one material can be fully effective for all types of cell and ensuing tissues. Scaffolds need to address the delicate balance between cell-scaffold interactions and the particular requirements of different cell types. To address the specific needs for the controlled growth of tissues it is imperative to match scaffold stiffness and elasticity to cells and tissues of interest to promote regeneration success. We here report an efficient method for creating scaffolds of tunable elasticity by generating a range of composites based on ε-caprolactone-D,L-lactide-based elastomer with cellulose nanocrystals (CNC). Two specific composites with different Young's modulus (E) values (~5 MPa and ~15 MPa) were selected and fully evaluated by tensile tests, Fourier Transform-Infrared (FT-IR), Scanning Electron Microscopy (SEM), contact angle measurements, and X-ray scattering. As a proof of concept this work studies how matching the scaffold's mechanical properties to neuroblastomas and fibroblasts cells affects cell behavior. Specifically, the composite with lower E, by design with less CNC content, is more suitable for neuroblastomas, whereas the one with higher E via higher CNC content is more suited for human dermal fibroblasts. The approach of matching cells with appropriate mechanical environments can provide important insights into fundamental cell behaviors.

36 MATERIALS SCIENCE↗
DOE OSTI2022

PolyDODT: a macrocyclic elastomer with unusual properties

The effect of reaction conditions on the structure of poly(3,6-dioxa-1,8-octanedithiol) (polyDODT) made by Reversible Radical Recombination Polymerization (R3P) using triethylamine (TEA), H 2 O 2 and air was investigated. 800 MHz (1 and 2D) NMR was used to investigate the polymer structures. Sensitivity analysis provided direct evidence for high purity cyclic polyDODT up to M n ~ 100 000 g mol –1 . Here, comparative analysis by High Resolution Multidetector Size Exclusion Chromatography (SEC) using integrated data showed that the cycles had lower viscosity and were more compact (both for R g and R h ) than linear samples of similar molecular weight. However, differential data revealed unusual behavior. While lower molecular weight cyclic polymers eluted later and had lower intrinsic viscosity than their linear counterparts at the same molecular weight, at higher molecular weights the polymers showed strange behavior: both the diffusion coefficient measured by Quasielastic Light Scattering (QELS) and Mark–Houwink–Sakurada plots of intrinsic viscosity for linear and cyclic polyDODT were found to converge. R3P, an aqueous based “green” method is capable of producing polymers at the 10–100 g scale in the lab, which will allow more detailed studies of this new class of biodegradable elastomers so further experimentation can be performed to elucidate the reasons for the unusual findings.

36 MATERIALS SCIENCE↗