Results for “effective core potentials” — Page 10

NASA NTRS2021

Experimental and Analytical Characterization of Fluted-Core Sandwich Composite Structures

As composite materials continue to gain wider acceptance for aerospace primary structures, experimental characterization and analysis methods must evolve, especially if new or underutilized composite structural concepts are to be successfully implemented. One such potentially underutilized concept is the fluted-core sandwich composite, which consists of facesheets separated by angled web members, and has a number of potential advantages over traditional-core (honeycomb, foam, etc.) sandwich composites. However, fluted-core sandwich composites also exhibit a behaviors not seen with traditional-core sandwich composites. For example, stable local buckling that can lead to material failure can occur in the facesheets between webs or in the webs themselves. Additionally, in the direction perpendicular to the webs, the effective transverse-shear stiffness is largely determined by the bending stiffnesses of the facesheets and the webs and is generally much lower than in the direction parallel to the webs. These local buckling and transverse-shear behaviors can have a large influence on material failure and global buckling, respectively. Thus, it is important to accurately characterize and model these behaviors. In this report, a series of experiments designed to elicit some of these fluted-core sandwich composite structural responses is discussed and the results are compared with results from a previously developed finite element analysis approach; qualitative and quantitative agreement between the experiment and analysis is shown.

Marc R. Schultz↗

NASA NTRS1993

Development of hypersonic engine seals - Flow effects of preload and engine pressures

A new type of engine seal is being developed to meet the needs of advanced hypersonic engines. A seal braided of emerging high temperature ceramic fibers comprised of a sheath-core construction has been selected for study based on its low leakage rates. Flexible, low-leakage, high-temperature seals are required to seal the movable engine panels of advanced ramjet-scramjet engines either preventing potentially dangerous leakage into backside engine cavities or limiting the purge coolant flow rates through the seals. To predict the leakage through these flexible, porous seal structures as a function of preload and engine pressures, new analytical flow models are required. An empirical leakage resistance/preload model is proposed to characterize the observed decrease in leakage with increasing preload. Empirically determined compression modulus and preload factor are used to correlate experimental leakage data for a wide range of seal architectures. Good agreement between measured and predicted values are observed over a range of engine pressures and seal preload.

Cai, Zhong↗

NASA NTRS2015

Ice Accretion Measurements on an Airfoil and Wedge in Mixed-Phase Conditions

This paper describes ice accretion measurements from experiments conducted at the National Research Council (NRC) of Canada's Research Altitude Test Facility during 2012. Due to numerous engine power loss events associated with high altitude convective weather, potential ice accretion within an engine due to ice crystal ingestion is being investigated collaboratively by NASA and NRC. These investigations examine the physical mechanisms of ice accretion on surfaces exposed to ice crystal and mixed phase conditions, similar to those believed to exist in core compressor regions of jet engines. A further objective of these tests is to examine scaling effects since altitude appears to play a key role in this icing process.

ice crystals↗

NASA NTRSDate not supplied

Uncertainty Quantification of Inducer Natural Frequency using Conditional Assessment of Modeling and Modal Testing of Simpler Systems

The low pressure fuel pump inducer of the new Space Launch System RS25 core stage engine operates in a highly complex environment that substantially affects its modal characteristics. Some of the more important effects are fluid-added mass resulting from operation within a light liquid (Hydrogen), and the magnification of this effect due to tight tip clearance. Since higher order cavitation has been identified as a significant harmonic driver, knowledge of the natural frequency of potentially excitable modes is critical for safe operation, but this frequency cannot be measured during the severe operational environment. A comprehensive testing and analysis program has therefore been performed over the last four years to identify the nominal value and uncertainty of the frequency by modeling and testing four simpler structures which share some of the characteristics of the operational inducer. This testing was used to assess and adjust modeling techniques and excellent correlation was achieved. Identification of the uncertainty in the inducer frequency itself was still problematic, however. This difficulty led to an investigation of Bayesian uncertainty quantification techniques, and to the application of the relatively simple technique of Multi-Variate Normal conditional distributions to calculate the inducer natural frequency uncertainty. Assumptions on prior distributions of uncertainty of the fluid-added mass and tip clearance effect are initially applied to models of each of the simple structures and the inducer itself, and these uncertainties are propagated to generate natural frequencies using design of experiments. Simple response surfaces are then created from this data in order to calculate a Covariance Matrix relating all of these natural frequencies. Finally, the results from modal test of the simple structures are considered to be observations and used to calculate the conditional variance of the desired inducer frequencies. As this method is less rigorous than more complicated Bayesian methods reported in the literature, a conservative factor is applied to the result, but the resulting uncertainty is still significantly less than originally estimated and will greatly assist certification of the inducer for use in the engine.

Uncertainty Quantification↗

NASA NTRSDate not supplied

Uncertainty Quantification of Inducer Eigenvalues using Conditional Assessment of Models and Modal Test of Simpler Systems

The low pressure fuel pump inducer of the new Space Launch System RS25 core stage engine operates in a highly complex environment that substantially affects its modal characteristics. Some of the more important effects are fluid-added mass resulting from operation within a light liquid (Hydrogen), and the magnification of this effect due to tight tip clearance. Since higher order cavitation has been identified as a significant harmonic driver, knowledge of the natural frequency of potentially excitable modes is critical for safe operation, but this frequency cannot be measured during the severe operational environment. A comprehensive testing and analysis program has therefore been performed over the last four years to identify the nominal value and uncertainty of the frequency by modeling and testing four simpler structures which share some of the characteristics of the operational inducer. This testing was used to assess and adjust modeling techniques and excellent correlation was achieved. Identification of the uncertainty in the inducer frequency itself was still problematic, however. This difficulty led to an investigation of Bayesian uncertainty quantification techniques, and to the application of the relatively simple technique of Multi-Variate Normal conditional distributions to calculate the inducer natural frequency uncertainty. Assumptions on prior distributions of uncertainty of the fluid-added mass and tip clearance effect are initially applied to models of each of the simple structures and the inducer itself, and these uncertainties are propagated to generate natural frequencies using design of experiments. Simple response surfaces are then created from this data in order to calculate a Covariance Matrix relating all of these natural frequencies. Finally, the results from modal test of the simple structures are considered to be observations and used to calculate the conditional variance of the desired inducer frequencies. As this method is less rigorous than more complicated Bayesian methods reported in the literature, a conservative factor is applied to the result, but the resulting uncertainty is still significantly less than originally estimated and will greatly assist certification of the inducer for use in the engine.

Uncertainty Quantification↗

NASA NTRS1980

The X-ray structure of two rich galaxy clusters and its implications for the detectability of microwave diminutions

The X-ray observations of the galaxy clusters Abell 2319 and 576 show a reduced temperature of the microwave background due to the Suniaev-Zeldovich effect. The X-ray maps indicate smooth emission in these clusters concentrated toward the optical center; the surface brightness in the 1-3 keV band falls with the inverse square of radius outside a small core, and fits the Hubble's law of optical surface brightness of elliptical galaxies. The low temperature indicates that in A576 (1) the core radius of the gravitational potential is two to three times larger than inferred from galaxy counts, (2) the temperature rises with radius over most of the cluster and falls to zero at large radii, and (3) the gas does not obey the equation of state.

White, S. D. M.↗

NASA NTRS2005

Acoustic and Aero-Mixing Experimental Results for Fluid Shield Scale Model Nozzles

The principle objectives of this investigation are to evaluate the acoustic and aerodynamic characteristics of fluid shield nozzle concept and to assess Far 36, Stage 3 potential for fluid shield nozzle with Flade Cycle. Acoustic data for nine scale model nozzle configurations are obtained. The effects of simulated flight and geometric and aerothermodynamic flow variables on the acoustic behavior of the fluid shield are determined. The acoustic tests are aimed at studying the effect of: (1) shield thickness, (2) wrap angle, (3) mass flow and velocity ratios between shield and core streams at constant cycle specific thrust (i.e., mixed velocity), (4) porous plug, and (5) subsonic shield. Shadowgraphs of six nozzle configurations are obtained to understand the plume flowfield features. Static pressure data on suppressor chutes in the core stream (shielded and unshielded) sides and on plug surface are acquired to determine the impact of fluid shield on base drag of the 36-chute suppressor nozzle and the thrust augmentation due to the plug, respectively.

Salikuddin, M.↗

NASA NTRS1994

Equatorial heating and hemispheric decoupling effects on inner magnetospheric core plasma evolution

We have extended our previous semikinetic study of early stage plasmasphere refilling with perpendicular ion heating by removing the restriction that the northern and southern boundaries are identical and incorporating a generalized transport description for the electrons. This allows investigation of the effects of electron heating and a more realistic calculation of electric fields produced by ion and electron temperature anisotropies. The combination of perpendicular ion heating and parallel electron heating leads to an equatorial electrostatic potential peak, which tends to shield and decouple ion flows in the northern and southern hemispheres. Unequal ionospheric upflows in the northern and southern hemispheres lead to the development of distinctly asymmetric densities and other bulk parameters. At t = 5 hour after the initiation of refiling with different source densities (N(sub north) = 100 cu/cm, N(sub south) = 50 cu/cm), the maximum potential drops of the northern and southern hemispheres are 0.6 and 1.3 V, respectively. At this time the minimum ion densities are 11 and 7 cu/cm for the northern and southern hemispheres. DE 1 observations of asymmetric density profiles by Olsen may be consistent with these predictions. Termination of particle heating causes the reduction of equatorial potential and allows interhemispheric coupling. When the inflows from the ionospheres are reduced (as may occur after sunset), decreases in plasma density near the ionospheric regions are observed while the heated trapped ion population at the equator persists.

Lin, J.↗

NASA NTRS2013

Development of Stacked Core Technology for the Fabrication of Deep Lightweight UV Quality Space Mirrors

Decadal Survey stated that an advanced large-aperture ultraviolet, optical, near-infrared (UVOIR) telescope is required to enable the next generation of compelling astrophysics and exoplanet science; and, that present technology is not mature enough to affordably build and launch any potential UVOIR mission concept. Under Science and Technology funding, NASA's Marshall Space Flight Center (MSFC) and ITT Exelis have developed a more cost effective process to make up to 4m monolithic spaceflight UV quality, low areal density, thermally and dynamically stable primary mirrors. A proof of concept mirror was completed at ITT Exelis and tested down to 250K at MSFC which would allow imaging out to 2.5 microns. The parameters and test results of this concept mirror will be shown. The scale-up process will be discussed and the technology development path to a 4m mirror system by 2018 will also be outlined.

Matthews, Gary↗

NASA NTRS2013

Development of Stacked Core Technology for the Fabrication of Deep Lightweight UV Quality Space Mirrors

Decadal Survey stated that an advanced large-aperture ultraviolet, optical, near-infrared (UVOIR) telescope is required to enable the next generation of compelling astrophysics and exoplanet science; and, that present technology is not mature enough to affordably build and launch any potential UVOIR mission concept. Under Science and Technology funding, NASA's Marshall Space Flight Center (MSFC) and ITT Exelis have developed a more cost effective process to make up to 4m monolithic spaceflight UV quality, low areal density, thermally and dynamically stable primary mirrors. A proof of concept mirror was completed at ITT Exelis and tested down to 250K at MSFC which would allow imaging out to 2.5 microns. The parameters and test results of this concept mirror will be shown. The scale-up process will be discussed and the technology development path to a 4m mirror system by 2018 will also be outlined.

Matthews, Gary W.↗

NASA NTRS2013

The Development of Stacked Core Technology for the Fabrication of Deep Lightweight UV-quality Space Mirrors

The Decadal Survey stated that an advanced large-aperture ultraviolet, optical, near-infrared (UVOIR) telescope is required to enable the next generation of compelling astrophysics and exoplanet science; and, that present technology is not mature enough to affordably build and launch any potential UVOIR mission concept. Under Science and Technology funding, NASA's Marshall Space Flight Center (MSFC) and Exelis have developed a more cost effective process to make up to 4m monolithic spaceflight UV quality, low areal density, thermally and dynamically stable primary mirrors. A proof of concept mirror was completed at Exelis and tested down to 250K at MSFC which would allow imaging out to 2.5 microns. The parameters and test results of this concept mirror will be shown. The scale-up process will be discussed and the technology development path to a 4m mirror system by 2018 will also be outlined.

Matthews, Gary W.↗

NASA NTRS2014

The Development of Stacked Core for the Fabrication of Deep Lightweight UV-Quality Space Mirrors

The 2010 Decadal Survey stated that an advanced large-aperture ultraviolet, optical, near-infrared (UVOIR) telescope is required to enable the next generation of compelling astrophysics and exoplanet science; and, that present technology is not mature enough to affordably build and launch any potential UVOIR mission concept. Under Science and Technology funding, NASA's Marshall Space Flight Center (MSFC) and Exelis have developed a more cost effective process to make 4m class or larger monolithic spaceflight UV quality, low areal density, thermally and dynamically stable primary mirrors. A proof of concept 0.43m mirror was completed at Exelis optically tested at 250K at MSFC which demonstrated the ability for imaging out to 2.5 microns. The parameters and test results of this concept mirror are shown. The next phase of the program includes a 1.5m subscale mirror that will be optically and dynamically tested. The scale-up process will be discussed and the technology development path to a 4m mirror system by 2018 will be outlined.

Matthews, Gary W.↗

NASA NTRS1982

O1, P1, N2 models of the global ocean tide on an elastic earth plus surface potential and spherical harmonic decompositions for M2, S2, and K1

The models of M2, S2, and K1 presented in Parke and Hendershott (1980) are supplemented with models of O1, P1, and N2. The models satisfy specified elevation boundary conditions and are generated by fighting a small number of test functions to island data. Maps are presented of the geocentric tide, the induced free space potential, the induced vertical component of the solid earth tide, and the induced vertical component of the gravitational field for each new component. Maps of the tidal potential seen by an observer fixed to the surface of the solid earth are also presented for all six constituents. Spherical harmonic coefficients up to order four and the rms magnitude of the coefficients to order fifteen are presented for each constituent. The rms magnitudes of the P1 and K1 coefficients normalized by their respective equilibrium amplitudes are compared to determine the effect of the diurnal core resonance.

Parke, M. E.↗

NASA NTRS2019

Near-Exit Pressure Fluctuations in Jets from Circular and Rectangular Nozzles

This article documents some experimental observations made for near-exit unsteady pressure fluctuations in high-speed jets. These fluctuations are apparently related to ‘trapped waves’ within the jet potential core as investigated and reported recently by other researchers. Round nozzles of three different diameters and rectangular nozzles of three different aspect ratios are studied. The pressure fluctuations manifest as a series of peaks in the spectra. These ‘trapped wave spectral peaks’ are found with all nozzles. Their characteristics and variations with axial and radial distances as well as with jet Mach number are documented. Effects of initial boundary layer state and the presence of a surface nearby as well as the scaling of the frequencies of the spectral peaks are studied and discussed.

Zaman, K. B. M. Q.↗

NASA NTRS1992

The time-dependent response of 3- and 5-layer sandwich beams

Simple sandwich beam models have been developed to study the effect of the time-dependent constitutive properties of fiber-reinforced polymer matrix composites, considered for use in orbiting precision segmented reflectors, on the overall deformations. The 3- and 5-layer beam models include layers representing the face sheets, the core, and the adhesive. The static elastic deformation response of the sandwich beam models to a midspan point load is studied using the principle of stationary potential energy. In addition to quantitative conclusions, several assumptions are discussed which simplify the analysis for the case of more complicated material models. It is shown that the simple three-layer model is sufficient in many situations.

Hyer, M. W.↗

NASA NTRS2020

Low NOx Fuel-Flex Combustor Summary

Combustion and emissions testing of United Technologies Research Center’s (UTRC’s) small core combustor in NASA GRC’s CE-5 flametube test facility comprising of LTO and cruise conditions has been completed. Sufficient NOx emissions data was collected to formulate correlation equations for assessing reductions in NOx for LTO against CAEP/6 and cruise against 2005 best-in-class. Back-to-back testing of Jet-A fuel and a 50/50 blend of Jet-A with an alternative fuel demonstrated a measurable effect of fuel composition on non-volatile particulate matter emissions. Post-test analysis indicates LTO NOx emissions >80% below CAEP6 in UTRC single-sector tests of small-core N+3 combustor. Documentation describing N+3 combustor concept selected, design approach, initial flametube test & analysis results; and preferred concept recommended for higher fidelity research has also been completed. This Lean Burn combustor concept shows potential to meet/exceed NASA’s Far Term LTO NOX reduction goals, but further investigation of dynamic characteristics of the combustor concept are required to ensure good operability over the entire flight regime conditions.

Angela D Surgenor↗

NASA NTRS2020

Turbulent mixing in supercritical jets: effect of compressibility factor and inflow condition

Fuel injection and turbulent mixing at supercritical pressures determines ignition and combustion in numerous engineering applications. Flow evolution under such conditions is characterized by strong non-linear coupling between dynamics, transport coefficients, and thermodynamics. Experimental studies observe that the jets injected at supercritical pressures exhibit significantly different dynamics from the jets at subcritical conditions, owing to the lack of distinct liquid and gas phases in supercritical state. Thus, the averaged flow quantities such as the potential core length, jet spatial growth rate and velocity decay profiles differ in the two conditions, resulting in different mixed-fluid distributions. In this study, turbulent jet direct numerical simulations (DNS) are performed to examine the variations in flow statistics between injection of Nitrogen (N₂) in Nitrogen (N₂) at both subcritical (perfect-gas) and supercritical conditions. In all cases, isothermal round jets at Reynolds number (Re_{D}), based on jet diameter (D) and jet orifice velocity (U₀), of 5000 are considered. For mixing analyses, a passive scalar transported with the flow is examined.

Sharan, Nek↗

NASA NTRSDate not supplied

Flow Characterization of the NASA Langley Unitary Plan WindTunnel, Test Section 2: Computational Results

Flow in the empty Unitary Planform Wind Tunnel at the NASA Langley Research Center issimulated with computational fluid dynamics methods. The objectives are to assess CFD’s truepredictive capability and to generate flow-field maps upstream of the tunnel’s test section foruse in associated vehicle tests. Multiple CFD solvers, grid adaption methods, and turbulencemodels are used by five teams doing the simulations. The simulation domain is as large aspractical: from the start of the settling chamber, just downstream of the last set of turningvanes, to well downstream of the test section. Simulations are done at three Mach numbers andseveral Reynolds numbers that cover most of the tunnel’s operating range. The sensitivity ofthe CFD solutions to simulation process details, including turbulence model, spatial resolutionand settling-chamber inflow velocity profile, is characterized. Significant sensitivities in somedetails of the predicted test section flow are described. CFD predicts that details of flow inthe settling chamber can affect the flow in the test section. Turning of the flow through thetunnel contraction and past nozzle-block hardware generates streamwise vortices, some ofwhich survive into the core of the test section, principally at low Mach number. Preliminarycomparisons to experimental measurements are given. The major flow characteristics andthe dynamical vortices predicted by CFD exist in the experiment. Several details in CFD andexperiment are observed to differ, including the effects of the vortices and features that appearto be Mach waves in the test section. Sensitivity to grid resolution and turbulence modelingis noted in the vortices; no potential cause for the differences in Mach waves has yet beenidentified in the CFD sensitivity studies.

wind tunnel↗