SEARCH · Engineering Papers

Results for “dry lubricant”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS1987

The effect of Tricresyl-Phosphate (TCP) as an additive on wear of Iron (Fe)

The effect of tricresyl phosphate (TCP) as an antiwear additive in lubricant trimethyol propane triheptanoate (TMPTH) was investigated. The objective was to examine step loading wear by use of surface analysis, wetting, and chemical bonding changes in the lubricant. The investigation consisted of steploading wear studies by a pin or disk tribometer, the effects on wear related to wetting by contact angle and surface tension measurements of various liquid systems, the chemical bonding changes between lubricant and TCP chromatographic analysis, and by determining the reaction between the TCP and metal surfaces through wear scar analysis by Auger emission spectroscopy (AES). The steploading curve for the base fluid alone shows rapid increase of wear rate with load. The steploading curve for the base fluid in presence of 4.25 percent by volume TCP under dry air purge has shown a great reduction of wear rate with all loads studied. It has also been found that the addition of 4.25 percent by volume TCP plus 0.33 percent by volume water to the base lubricant under N2 purge also greatly reduces the wear rate with all loads studied. AES surface analysis reveals a phosphate type wear resistant film, which greatly increases load-bearing capacity, formed on the iron disk. Preliminary chromatographic studies suggest that this film forms either because of ester oxidation or TCP degradation. Wetting studies show direct correlation between the spreading coefficient and the wear rate.

Ghose, Hiren M.↗

NASA NTRS1989

Plasma-deposited amorphous hydrogenated carbon films and their tribological properties

Recent work on the properties of diamondlike carbon films and their dependence on preparation conditions are reviewed. The results of the study indicate that plasma deposition enables one to deposit a variety of amorphous hydrogenated carbon (a-C:H ) films exhibiting more diamondlike behavior to more graphitic behavior. The plasma-deposited a-C:H can be effectively used as hard, wear-resistant, and protective lubricating films on ceramic materials such as Si(sub 3)N(sub 4) under a variety of environmental conditions such as moist air, dry nitrogrn, and vacuum.

Miyoshi, Kazuhisa↗

NASA NTRS1989

Plasma-deposited amorphous hydrogenated carbon films and their tribological properties

Recent work on the properties of diamondlike carbon films and their dependence on preparation conditions are reviewed. The results of the study indicate that plasma deposition enables one to deposit a variety of amorphous hydrogenated carbon (a-C:H) films exhibiting more diamondlike behavior to more graphitic behavior. The plasma-deposited a-C:H can be effectively used as hard, wear-resistant, and protective lubricating films on ceramic materials such as Si(sub 3)N(sub 4) under a variety of environmental conditions such as moist air, dry nitrogen, and vacuum.

Miyoshi, K.↗

NASA NTRS1981

Evaluation of boundary lubricants using steady-state wear and friction

A friction and wear study was made at 20 C to establish operating limits and procedures for obtaining improved reproducibility and reliability in boundary lubrication testing. Ester base and C-other base fluids were used to lubricate a pure iron rider in sliding contact with a rotating M-50 steel disk in a pin-on-disk apparatus. Results of a parametric study with varying loads and speeds slowed that satisfactory test conditions for studying the direction and wear characteristics in the boundary lubrication regime with this test device were found to be 1 kilogram load; 7 to 9 meters-per-minute (50 rpm) surface speed; dry air test atmosphere (less than 100 ppm H2O); and use of a time stepwise procedure for measuring wear. Highly reproducible steady-state wear rates resulted from the two fluid studies which had a linearity of about 99 percent after initially higher wear rates and friction coefficients during run-in periods of 20 to 40 minutes.

Loomis, W. R.↗

NASA NTRS1982

Tribological characteristics of nitrogen (N+) implanted iron

The effect of implantation of nitrogen ions (1.5 MeV) on the friction and wear characteristics of pure ion sliding against M-50 steel (unimplanted) was studied in a pin-on-disk sliding friction apparatus. Test conditions included room temperature (25 C), a dry air atmosphere, a load of 1/2 kg (4.9 N), sliding velocities of 0.043 to 0.078 m/sec (15 to 25 rpm), a pure hydrocarbon lubricant (n-hexadecane), or a U.S.P. mineral oil and nitrogen ion implantation doses of 5x10 to the 15th power and 5x10 to the 17th power ions/sq cm. No differences in wear rates were observed in the low dose experiments. In the high dose experiments, small reductions in initial (40 percent) and steady state (20 percent) wear rates were observed for nitrogen implanted iron riders as compared with unimplanted controls. No differences in average friction coefficients were noted for either dose. Auger electron spectroscopy combined with argon ion bombardment revealed a subsurface Gaussian nitrogen distribution with a maximum concentration of 6 atomic percent at a depth of 0.8 microns. Similar analysis within the wear scar of an implanted rider after 20 microns of wear yielded only background nitrogen concentration. No inward migration of nitrogen ions was observed.

Jones, W. R.↗

NASA NTRS1983

Tribological characteristics of nitrogen (N+) implanted iron

Jones, W. R., Jr.↗

NASA NTRS1995

Diamond and diamondlike carbon as wear-resistant, self-lubricating coatings for silicon nitride

Recent work on the friction and wear properties of as-deposited fine-grain diamond, polished coarse-grain diamond, and as-deposited diamondlike carbon (DLC) films in humid air at a relative humidity of approximately 40 percent and in dry nitrogen is reviewed. Two types of chemical vapor deposition (CVD) processes are used to deposit diamond films on silicon nitride (Si3N4) substrates: microwave-plasma and hot-filament. Ion beams are used to deposit DLC films of Si3N4 substrates. The diamond and DLC films in sliding contact with hemispherical bare Si3N4 pins have low steady-state coefficients of friction (less than 0.2) and low wear rates (less than 10(exp -7) mm(exp 2)/N-m), and thus, can be used effectively as wear-resistant, self-lubricating coatings for Si3N4 in the aforementioned two environments.

Miyoshi, Kazuhisa↗

DOE OSTI2021

Stress- and Time-Dependent Formation of Self-Lubricating In Situ Carbon (SLIC) Films on Catalytically-Active Noble Alloys

Abstract Low shear strength (30 MPa) organic films were grown in situ on Pt 0.9 Au 0.1 surfaces via cyclic sliding contact in dry N 2 with trace concentrations of ambient hydrocarbons. We present a systematic investigation of the stress- and time-dependent film formation. Steady-state friction coefficients were found to be as low as µ ~ 0.015 and inversely proportional to contact pressure, revealing non-Amontonian behavior. Above a Hertzian contact pressure of ~500 MPa, shear strength dropped, indicating an activated process. Raman spectroscopy identified non-uniformity in areal coverage and relative order with contact pressure. Regions of steady-state low-friction behavior exhibited spectra similar to DLC coatings. Atomic force microscopy was used to study the formation and growth of films at the nanoscale. Stress- and time-dependent measurements suggested a sublinear increase of film volume with time, and a transition from growth to wear at a Hertzian contact pressure of ~1.2 GPa.

Jones, Morgan R.↗

NASA NTRS2010

Test Validation of the Repair to the Space Station Solar Alpha Rotary Joint

The Solar Array Alpha Joint Lubrication Interval Test (SARJ LITE) test rig was built as a method to evaluate the performance of the grease repair on the Starboard SARJ of the International Space Station (ISS) . The on-orbit SARJ was temporarily parked after receiving significant damage on one of its race ring surfaces as a result of inadequate lu brication (high dry contact friction) and unaccounted for roller traction kinematics. In a scaled down rig, flight-like roller bearings wer e preloaded and cycled on a nitrided 15-5 race surface. Grease was ad ded to the track and with instrumentation monitoring performance, trending data will be extracted and used to determine lubrication interva ls for both Port and Starboard ISS SARJ?s. The grease lubrication was found to be effective in eliminating the high friction that contributed to the onorbit race damage.

Allmon, Curtis↗

DOE OSTI2022

Alternate Methods for Cleaning Zirconium Plate

The United States High Performance Research Reactor Conversion Program identified the need to transition from highly enriched uranium fuel to lowly enriched uranium fuel for high power research and civil reactors. One of the fuel configurations selected for these reactors was a uranium (U) foil alloyed with 10% molybdenum (Mo). The U-10Mo fuel foil was then covered with a zirconium (Zr) interlayer and pressed into an aluminum cladding. Idaho National Laboratory prescribed a need to remove surface oxidation on the Zr prior to bonding it with U-10Mo fuel foil. To determine the best method of oxidation removal, a variety of polishing methods, including hand polishing with a diamond paste or Scotch-Brite™ pads, mechanically wet-polishing with abrasive belts, and chemical etching with hydrofluoric/nitric acid mixtures, were investigated on pre-polished Zircaloy 702 sheets purchased directly from the manufacturer. No change in surface roughness was detected using any of these methods relative to the as-received material. In fact, scanning electron microscopy detected grit from hand polishing with Amplex Grade 30 waste soluble diamond paste and Scotch-Brite™ pads. Visible staining was found, and fluorine detected via X-ray photoelectron spectroscopy on the flash etching samples. These contaminants were not seen on the as-received material. In addition to the need to remove the oxide layer on the Zr prior to co-rolling, there are concerns that the Neolube debonding agent on the co-rolling can may contaminate the Zr surface after co-rolling. The experimental results found that zirconium in contact with Neolube coated steel plates was easily cleaning with ethanol wiping after heat treated and no carbide inclusions remained on the surface. Overall, all cleaning methods tested did not significantly change the surface roughness of the plates or reduce the oxide layer present on the zirconium. Carbon was found on all the samples, before and after cleaning, except for the flash etch samples which detected fluorine instead. The insignificant changes seen in the cleaned plates relative to the as received plates question the need for cleaning prior to rolling. Further investigation in the requirements for cleaning at this step is recommended. Current methods for cleaning the surface after hot rolling with alcohol appear sufficient. After hot rolling, if Neolube does peel off the can and onto the zirconium coated foil surface, a dry abrasive or diamond paste polish is not recommended due to the chance of abrasive being embedded into the surface. However, the ability of an etchant to lift the lubricant off the zirconium surface indicates that a spot etch method could work to clean specific spots where Neolube is present, if the need arises.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS2010

Ceramic Rail-Race Ball Bearings

Non-lubricated ball bearings featuring rail races have been proposed for use in mechanisms that are required to function in the presence of mineral dust particles in very low-pressure, dry environments with extended life. Like a conventional ball bearing, the proposed bearing would include an inner and an outer ring separated by balls in rolling contact with the races. However, unlike a conventional ball bearing, the balls would not roll in semi-circular or gothic arch race grooves in the rings: instead, the races would be shaped to form two or more rails (see figure). During operation, the motion of the balls would push dust particles into the spaces between the rails where the particles could not generate rolling resistance for the balls

Balzer, Mark A.↗

DOE OSTI2020

Towards developing robust solid lubricant operable in multifarious environments

Abstract Conventional solid lubricants such as MoS 2 , graphite, or diamond-like carbon films demonstrate excellent tribological performance but only in specific environments due to their inherent materials properties. This limitation prohibits using these solid lubricants in environments that change dynamically. This study presents the results of a novel solid lubricant that was developed using a combination of solution-processed 2D-molybdenum disulfide and graphene-oxide (GO) that can be deposited on to stainless steel substrates using a simple spray-coating technique and show exceptional performance in multifarious environments namely, ambient (humid) atmosphere, dry nitrogen, and vacuum. The tribological performance of the coatings was evaluated using a ball-on-disc sliding test and demonstrated an excellent wear/friction performance in all environments and coating survived even after 44 km of linear sliding. Transmission electron microscopy and Raman spectroscopy analysis of the tribolayers suggested in-operando friction-induced re-orientation of MoS 2 layers that were protected by GO layers and, an absence of MoO x peaks indicate a strong resistance to intercalation with moisture and oxygen. The simplicity and robustness of the hybrid MoS 2 –GO solid lubricant in mitigating wear-friction behavior of steel-on-steel tribopair in a multifarious environment is a game-changing and is promising for various applications.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Electrodeposited Mo x S y O z /Ni Tribological Coatings

Deposition of molybdenum disulfide (MoS 2 ) coatings using physical vapor deposition (PVD) and mechanical burnishing has been widely assessed for solid lubricants in space applications but still suffers from line-of-sight constraints on complex geometries. Here, we highlight one of the first demonstrations of electrodeposited Mo x S y O z and Mo x S y O z /Ni thin-film coatings from aqueous solutions of ammonium tetrathiomolybdate for solid lubricant applications and their remarkable ability to provide low coefficients of friction and high wear resistance. Characterization of the coating morphology shows amorphous microstructures with a high oxygen content and cracking upon drying. Even so, electrodeposited Mo x S y O z can achieve low steady-state coefficients of friction (μ ∼ 0.05–0.06) and wear rates (2.6 × 10 –7 mm 3 /(N m)) approaching those of physical vapor deposited coatings (2.3 × 10 –7 mm 3 /(N m)). Additionally, we show that adding dopants such as nickel increased the wear rate (7.5 × 10 –7 mm 3 /(N m)) and initial coefficient of friction (μ i = 0.23) due to compositional modifications such as dramatic sub-stoichiometry (S/Mo ∼ 1) and expression of a NiO x surface layer, although doping did reduce the degree of cracking upon drying.

Babuska, Tomas F.↗

NASA NTRS1991

Lubrication with sputtered MoS2 films: Principles, operation, limitations

The present practices, limitations, and understanding of thin sputtered MoS2 films are reviewed. Sputtered MoS2 films can exhibit remarkable tribological properties such as ultralow friction coefficients (0.01) and enhanced wear lives (millions of cycles) when used in vacuum or dry air. To achieve these favorable tribological characteristics, the sputtering conditions during deposition must be optimized for adequate film adherence and appropriate structure (morphology) and composition.

Spalvins, T.↗

NASA NTRS1986

A thin film degradation study of a fluorinated polyether liquid lubricant using an HPLC method

A High Pressure Liquid Chromatography (HPLC) separation method was developed to study and analyze a fluorinated polyether fluid which is promising liquid lubricant for future applications. This HPLC separation method was used in a preliminary study investigating the catalytic effect of various metal, metal alloy, and ceramic engineering materials on the degradation of this fluid in a dry air atmosphere at 345 C. Using a 440 C stainless steel as a reference catalytic material it was found that a titanium alloy and a chromium plated material degraded the fluorinated polyether fluid substantially more than the reference material.

Morales, W.↗

DOE OSTI2020

Literature Review on the Theory and Measurement of Dry Sliding Friction of Metals

Understanding the friction behavior between two sliding bodies can inform the design of machines, processing of materials, and simulation of dynamic processes. Kinetic friction is a complex phenomenon that depends on a multitude of factors such as sliding velocity, normal force, contact area, surface roughness, material properties, lubrication conditions, and thermal effects. This literature review covers the major known effects of sliding velocity, normal load, and surface roughness on the measured kinetic friction coefficient in the context of microscopic friction phenomena. Classic macroscale friction models are reviewed to illustrate approaches for simulating friction behavior. Prominent experimental friction setups within the literature are discussed with respect to achievable velocity and pressure regimes. The background information gathered here will be used to inform experimental procedures and modeling strategies of the exploratory research (ER) project titled “Measurement of Dynamic Friction via Kolsky Bar” (20200418ER).

36 MATERIALS SCIENCE↗

NASA NTRS1992

Computing Thermal Performances Of Shafts And Bearings

SHABERTH computer program developed to predict steady-state and transient thermal performance of multi-bearing shaft system operating with either wet or dry friction. Calculates loads, torques, temperatures, and fatigue lives for ball and/or roller bearings on single shaft. Enables study of many causes of instabilities in bearings. Also provides for analysis of reaction of system to termination of supply of lubricant to bearings and other lubricated mechanical elements. Valuable software tool in design and analysis of shaft bearing systems. Written in FORTRAN IV.

Woods, Claudia M.↗

NASA NTRS2011

Effect of Test Environment on Lifetime of Two Vacuum Lubricants Determined by Spiral Orbit Tribometry

The destruction rates of a perfluoropolyether (PFPE) lubricant, Krytox 143AC, subjected to rolling contact with 440C steel in a spiral orbit tribometer at room temperature have been evaluated as a function of test environment. The rates in ultrahigh vacuum, 0.213 kPa (1.6 torr) oxygen and one atmosphere of dry nitrogen were about the same. Water vapor in the test environment-a few ppm in one atmosphere of nitrogen-reduced the destruction rate by up to an order of magnitude. A similar effect of water vapor was found for the destruction rate of Pennzane 2001A, an unformulated multiply alkylated cyclopentane (MAC) hydrocarbon oil.

Pepper, Stephen V.↗