Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “developable planes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Stereographic cloud heights from imagery of SMS/GOES satellites

Stereographic pairs of SMS/GOES images, generated simultaneously by the spin-scan cameras of each of two geostationary satellites (SMS 1 and SMS 2, separated by 32 degrees of longitude on February 17, 1975), have been analyzed photogrammetrically to yield cloud heights with a two-sigma uncertainty of 500 meters. The 32-degree angle between the image plane of the two satellites, plus the distortions involved in transferring the image of a nearly full hemisphere of the earth onto a plane, required the development of a special instrument to permit stereographic compilation. Cloud heights measured stereographically compared favorably with heights of the same clouds measured by radar and IR methods. The same SMS image pairs were used to measure mountain-top heights with a mean deviation of 0.24 km from cartographic values.

Minzner, R. A.↗
NASA NTRS1978

Aspheric grating for extreme ultraviolet astronomy

A family of plane curves is developed which can diffract incident parallel rays to a point focus. These curves, termed diffractoidal curves, are rotated around an axis to produce surfaces of revolution correspondingly termed diffractoids, whose imaging properties for sources at infinity are studied by ray tracing in a few examples. The paraboloid emerges as a limiting case of the diffractoid. A comparison is made between the stigmatic focusing properties of the diffractoid and the toroidal grating.

Kastner, S. O.↗
NASA NTRS1978

Modal control of the planar motion of a long flexible beam in orbit

Attitude control techniques for the pointing and stabilization of very large, inherently flexible spacecraft systems are investigated. The attitude dynamics and control of a long, homogeneous flexible beam whose center of mass is assumed to follow a circular orbit is analyzed. In this study, first order effects of gravity-gradient are included, whereas external perturbations and related orbital station keeping maneuvers are neglected. A mathematical model which describes the system deflections within the orbital plane has been developed by treating the beam as having a maximum of three discretized mass particles connected by massless, elastic structural elements. The uncontrolled dynamics of this system are simulated and, in addition, the effects of the control devices are considered. The concept of distributed modal control, which provides a means for controlling a system mode independently of all other modes, is examined. The effect of varying the number of modes in the model as well as the number and location of the control devices are also considered.

Sellappan, R.↗
NASA NTRS1979

A general and computationally fast formulation for radiative transfer with scattering

A general formulation of monocromatic radiative transfer with scattering has been developed for plane-parallel geometry. The inhomogeneous and nonisothermal medium absorbs, emits, and anisotropically scatters radiation. Surfaces can emit and scatter radiation in any specified manner. The solution procedure uses the fact that phase incoherent scattering is linear in radiative sources. Certain basic scattering functions are then defined and calculated by an adding computer code using matrix algebra. These scattering functions are weighted by the temperature field and summed (superimposed) to obtain the solution for any specific problem. Numerical results for exiting intensities and one-sided heat fluxes from general media bound by one arbitrary surface are presented. These parametric studies demonstrate the effects of scattering particles and surfaces on radiative transfer from inhomogeneous and nonisothermal media. Application of the formulation to radiative equilibrium is also discussed. The conclusion is that all problems in plane-parallel radiative transfer with scattering can be solved by a common and computationally fast algorithm based on this formulation.

Cogley, A. C.↗
NASA NTRS1982

MLA imaging systems

The development of the enabling technology and instrument/mission definition phase for the application of advanced solid state sensors for future experimental remote sensing missions is discussed. The development of focal planes, instrument concept/design, mission studies, and service requirements and an imaging spectrometer technology and a Shuttle sortie mission definition are outlined.

Ando, K. J.↗
NASA NTRS1982

Turbulent solution of the Navier-Stokes equations for an inhomogenous developing shear layer

To study the nonlinear physics of inhomogeneous turbulent shear flow, the unaveraged Navier-Stokes equations are solved numerically. For initial conditions a three-dimensional cosine velocity fluctuation and a mean-velocity profile with a step are used. Although the initial conditions are nonrandom. The flow soon becomes turbulent. Concentrated turbulent energy develops near the plane where the mean velocity gradient is initially infinite. The terms in the one-point correlation equation for turbulent energy, including those for the diffusion and production of turbulence, are calculated, the diffusion terms tend to make the turbulence more homogeneous.

Deissler, R. G.↗
NASA NTRS1986

Review of convectively cooled structures for hypersonic flight

Resurgent interest in development of Aerospace Plane and Orient Express type vehicles promises to stretch structural technology for hypersonic flight vehicles to the uppermost limits. Significant portions of the structure may require active cooling of some type to survive hostile environments. Despite a lack of recent research activity for cooled structures, a significant body of unclassified knowledge exists concerning such structures. Contractual and in-house research conducted mainly by NASA's Langley Research Center during the 60's and 70's on vehicles very similar to the proposed Orient Express has provided a substantial data base for convectively cooled hypersonic flight structures. Specifically, results are presented for regeneratively cooled structural concepts which have a relatively high heat flux capability and use the hydrogen fuel directly as a coolant; and for structural concepts which use a secondary coolant loop to absorb incident heating and then transfer the absorbed heat to the liquid hydrogen fuel as it flows to the engines. Results are presented to indicate application regions in terms of heat flux capability for various concepts and benefits for each concept. Experience gained and costs are discussed in terms of heat flux capability for various concepts and benefits for each concept. Additionally, experience gained and cost involved with design, fabrication, and testing of full-scale convectively cooled structures are discussed.

Shore, Charles P.↗
NASA NTRS1989

Navier-Stokes analysis of cold scramjet-afterbody flows

The progress of two efforts in coding solutions of Navier-Stokes equations is summarized. The first effort concerns a 3-D space marching parabolized Navier-Stokes (PNS) code being modified to compute the supersonic mixing flow through an internal/external expansion nozzle with multicomponent gases. The 3-D PNS equations, coupled with a set of species continuity equations, are solved using an implicit finite difference scheme. The completed work is summarized and includes code modifications for four chemical species, computing the flow upstream of the upper cowl for a theoretical air mixture, developing an initial plane solution for the inner nozzle region, and computing the flow inside the nozzle for both a N2/O2 mixture and a Freon-12/Ar mixture, and plotting density-pressure contours for the inner nozzle region. The second effort concerns a full Navier-Stokes code. The species continuity equations account for the diffusion of multiple gases. This 3-D explicit afterbody code has the ability to use high order numerical integration schemes such as the 4th order MacCormack, and the Gottlieb-MacCormack schemes. Changes to the work are listed and include, but are not limited to: (1) internal/external flow capability; (2) new treatments of the cowl wall boundary conditions and relaxed computations around the cowl region and cowl tip; (3) the entering of the thermodynamic and transport properties of Freon-12, Ar, O, and N; (4) modification to the Baldwin-Lomax turbulence model to account for turbulent eddies generated by cowl walls inside and external to the nozzle; and (5) adopting a relaxation formula to account for the turbulence in the mixing shear layer.

Baysal, Oktay↗
NASA NTRS1990

Effects of streamwise vorticity injection on turbulent mixing layer development

This paper investigates the effect of injected strong streamwise vorticity on the structure and development of a plane mixing layer originating from tripped boundary layers. The experiments were conducted in a mixing layer wind tunnel consisting of two separate legs which were driven individually by centrifugal blowers. It was found that, while the vorticity injection increased the growth rate in the near-field, the asymptotic growth rate was reduced by a factor of about two, together with the peak Reynolds stress levels. The result is attributed to the effect of the relatively strong and short wavelength streamwise vorticity in making the spanwise structures more three-dimensional and slowing down their pairing process, thus reducing entrainment, and hence growth.

Bell, James H.↗
NASA NTRS1993

Aeroelastic character of a National Aerospace Plane demonstrator concept

The paper provides an analytical assessment of the flutter character of an unclassified National Aerospace Plane configuration known as the demonstrator. Linear subsonic, supersonic, and hypersonic analysis indicate that the vehicle is prone to body-freedom flutter resulting from the decrease in vibration frequency of the all-moveable wing at high flight dynamic pressures. As the wing-pivot frequency decreases, it couples with the vehicle short-period mode resulting in dynamic instability. A similar instability sometimes occurs when the pivot mode couples with the fuselage-bending mode. Also assessed, for supersonic flight conditions, are configuration variations that include relocation of the wing further aft on the lifting-body fuselage, and the addition of body flaps to the rear of the vehicle. These changes are destabilizing because they result in severe wing-pivot/fuselage-bending instabilities at dynamic pressures lower than the instabilities indicated for the original demonstrator. Finally, a two-point wing support and actuation system concept is proposed for the National Aerospace Plane, which if developed may (according to cursory analysis) enhance overall stability.

Spain, Charles V.↗
NASA NTRS1994

Transport aircraft loading and balancing system: Using a CLIPS expert system for military aircraft load planning

The requirement for improving aircraft utilization and responsiveness in airlift operations has been recognized for quite some time by the Canadian Forces. To date, the utilization of scarce airlift resources has been planned mainly through the employment of manpower-intensive manual methods in combination with the expertise of highly qualified personnel. In this paper, we address the problem of facilitating the load planning process for military aircraft cargo planes through the development of a computer-based system. We introduce TALBAS (Transport Aircraft Loading and BAlancing System), a knowledge-based system designed to assist personnel involved in preparing valid load plans for the C130 Hercules aircraft. The main features of this system which are accessible through a convivial graphical user interface, consists of the automatic generation of valid cargo arrangements given a list of items to be transported, the user-definition of load plans and the automatic validation of such load plans.

Richardson, J.↗
NASA NTRS1995

Computerized design of controllers using data models

The major contributions of the grant effort have been the enhancement of the Compensator Improvement Program (CIP), which resulted in the Ohio University CIP (OUCIP) package, and the development of the Model and Data-Oriented Computer Aided Design System (MADCADS). Incorporation of direct z-domain designs into CIP was tested and determined to be numerically ill-conditioned for the type of lightly damped problems for which the development was intended. Therefore, it was decided to pursue the development of z-plane designs in the w-plane, and to make this conversion transparent to the user. The analytical development needed for this feature, as well as that needed for including compensator damping ratios and DC gain specifications, closed loop stability requirements, and closed loop disturbance rejection specifications into OUCIP are all contained in Section 3. OUCIP was successfully tested with several example systems to verify proper operation of existing and new features. The extension of the CIP philosophy and algorithmic approach to handle modern multivariable controller design criteria was implemented and tested. Several new algorithms for implementing the search approach to modern multivariable control system design were developed and tested. This analytical development, most of which was incorporated into the MADCADS software package, is described in Section 4, which also includes results of the application of MADCADS to the MSFC ACES facility and the Hubble Space Telescope.

Irwin, Dennis↗
NASA NTRS1999

Climb to Cruise Noise Test Results

A semi-empirical formula for the prediction of the broadband shock associated noise from rectangular supersonic jets in the fly-over plane has been developed. The predicted noise spectra compared very favorable with the measurement of Ponton, Manning and Seiner. Extension to side-line directions will be carried out.

Joshi, M. C.↗
NASA NTRS2002

Analysis of the Magneto-Hydrodynamic (MHD) Energy Bypass Engine for High-Speed Air-Breathing Propulsion

The performance of the MHD energy bypass air-breathing engine for high-speed propulsion is analyzed in this investigation. This engine is a specific type of the general class of inverse cycle engines. In this paper, the general relationship between engine performance (specific impulse and specific thrust) and the overall total pressure ratio through an engine (from inlet plane to exit plane) is first developed and illustrated. Engines with large total pressure decreases, regardless of cause or source, are seen to have exponentially decreasing performance. The ideal inverse cycle engine (of which the MHD engine is a sub-set) is then demonstrated to have a significant total pressure decrease across the engine; this total pressure decrease is cycle-driven, degrades rapidly with energy bypass ratio, and is independent of any irreversibility. The ideal MHD engine (inverse cycle engine with no irreversibility other than that inherent in the MHD work interaction processes) is next examined and is seen to have an additional large total pressure decrease due to MHD-generated irreversibility in the decelerator and the accelerator. This irreversibility mainly occurs in the deceleration process. Both inherent total pressure losses (inverse cycle and MHD irreversibility) result in a significant narrowing of the performance capability of the MHD bypass engine. The fundamental characteristics of MHD flow acceleration and flow deceleration from the standpoint of irreversibility and second-law constraints are next examined in order to clarify issues regarding flow losses and parameter selection in the MM modules. Severe constraints are seen to exist in the decelerator in terms of allowable deceleration Mach numbers and volumetric (length) required for meaningful energy bypass (work interaction). Considerable difficulties are also encountered and discussed due to thermal/work choking phenomena associated with the deceleration process. Lastly, full engine simulations utilizing inlet shock systems, finite-rate chemistry, wall cooling with thermally balanced engine (fuel heat sink), fuel injection and mixing, friction, etc. are shown and discussed for both the MHD engine and the conventional scramjet. The MHD bypass engine has significantly lower performance in all categories across the Mach number range (8 to 12.2). The lower performance is attributed to the combined effects of 1) additional irreversibility and cooling requirements associated with the MHD components and 2) the total pressure decrease associated with the inverse cycle itself.

Riggins, David W.↗
NASA NTRS2003

Estimation of Instantaneous TOA Albedo at 670 nm over Ice Clouds from POLDER Multidirectional Measurements

An algorithm that determines the 670-nm top-of-atmosphere (TOA) albedo of ice clouds over ocean using Polarization and Directionality of the Earth's Reflectance ( POLDER) multidirectional measurements is developed. A plane-parallel layer of ice cloud with various optical thicknesses and light scattering phase functions is assumed. For simplicity, we use a double Henyey-Greenstein phase function to approximate the volume-averaged phase function of the ice clouds. A multidirectional reflectance best-fit match between theoretical and POLDER reflectances is used to infer effective cloud optical thickness, phase function and TOA albedo. Sensitivity tests show that while the method does not provide accurate independent retrievals of effective cloud optical depth and phase function, TOA albedo retrievals are accurate to within similar to 3% for both a single layer of ice clouds or a multilayer system of ice clouds and water clouds. When the method is applied to POLDER measurements and retrieved albedos are compared with albedos based on empirical angular distribution models (ADMs), zonal albedo differences are generally smaller than similar to 3%. When albedos are compared with those on the POLDER-I ERB and Cloud product, the differences can reach similar to 15% at small solar zenith angles.

Sun, W.↗
NASA NTRS2008

Electrical Resistance as a NDE Technique to Monitor Processing and Damage Accumulation in SiC/SiC Composites

Ceramic matrix composites are suitable for high temperature structural applications such as turbine airfoils and hypersonic thermal protection systems. The employment of these materials in such applications is limited by the ability to process components reliable and to accurately monitor and predict damage evolution that leads to failure under stressed-oxidation conditions. Current nondestructive methods such as ultrasound, x-ray, and thermal imaging are limited in their ability to quantify small scale, transverse, in-plane, matrix cracks developed over long-time creep and fatigue conditions. Electrical resistance of SiC/SiC composites is one technique that shows special promise towards this end. Since both the matrix and the fibers are conductive, changes in matrix or fiber properties should relate to changes in electrical conductivity along the length of a specimen or part. Initial efforts to quantify the electrical resistance of different fiber and different matrix SiC/SiC composites will be presented. Also, the effect of matrix cracking on electrical resistivity for several composite systems will be presented. The implications towards electrical resistance as a technique applied to composite processing, damage detection, and life-modeling will be discussed.

Smith, Craig↗
NASA NTRS2008

Electrical Resistance Technique to Monitor SiC Composite Detection

Ceramic matrix composites are suitable for high temperature structural applications such as turbine airfoils and hypersonic thermal protection systems. The employment of these materials in such applications is limited by the ability to process components reliable and to accurately monitor and predict damage evolution that leads to failure under stressed-oxidation conditions. Current nondestructive methods such as ultrasound, x-ray, and thermal imaging are limited in their ability to quantify small scale, transverse, in-plane, matrix cracks developed over long-time creep and fatigue conditions. Electrical resistance of SiC/SiC composites is one technique that shows special promise towards this end. Since both the matrix and the fibers are conductive, changes in matrix or fiber properties should relate to changes in electrical conductivity along the length of a specimen or part. The effect of matrix cracking on electrical resistivity for several composite systems will be presented and some initial measurements performed at elevated temperatures under stress-rupture conditions. The implications towards electrical resistance as a technique applied to composite processing, damage detection (health monitoring), and life-modeling will be discussed.

Smith, Craig↗