Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “computational fluid dynamics simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Computational Fluid Dynamic Optimization of an Experimental Rotating Detonation Rocket Engine Nozzle

A parametric optimization study is performed on the nozzle of a laboratory rotating detonation rocket engine (RDRE) using a three-dimensional computational fluid dynamic simulation. The primary optimization objective is maximum nozzle thrust. The basic nozzle configuration is a shrouded, truncated plug. The fluid in the RDRE chamber leading to the nozzle is choked at its exit so that its cyclic behavior is unaffected by any changes to the nozzle design. Optimization is performed for a single operating point. Parameters varied are the overall nozzle area expansion ratio and the fraction of the expansion area that is provided by the shroud. These two parameters indirectly affect the angle of the plug nozzle cone, and the bluff body area associated with its truncation. Nozzle thrust is evaluated as the difference between the thrust of the RDRE chamber-plus-nozzle combination and that of the chamber alone. The nozzle produces approximately 20% of the total engine thrust. The baseline nozzle is found to perform well, yielding 58.1% of the thrust calculated for a notional ideal RDRE nozzle which can instantaneously change shape to allow isentropic expansion of every fluid element. Optimization improves the performance, bringing the nozzle thrust to 70.0% of the notional ideal, and total engine thrust (chamber-plus-nozzle) to 94% of the ideal.

detonation↗
NASA NTRSDate not supplied

Computational Fluid Dynamic Optimization of an Experimental Rotating Detonation Rocket Engine Nozzle

A parametric optimization study is performed on the nozzle of a laboratory rotating detonation rocket engine (RDRE) using a three-dimensional computational fluid dynamic simulation. The primary optimization objective is maximum nozzle thrust. The basic nozzle configuration is a shrouded, truncated plug. The fluid in the RDRE chamber leading to the nozzle is choked at its exit so that its cyclic behavior is unaffected by any changes to the nozzle design. Optimization is performed for a single operating point. Parameters varied are the overall nozzle area expansion ratio and the fraction of the expansion area that is provided by the shroud. These two parameters indirectly affect the angle of the plug nozzle cone, and the bluff body area associated with its truncation. Nozzle thrust is evaluated as the difference between the thrust of the RDRE chamber-plus-nozzle combination and that of the chamber alone. The nozzle produces approximately 20% of the total engine thrust. The baseline nozzle is found to perform well, yielding 58.1% of the thrust calculated for a notional ideal RDRE nozzle which can instantaneously change shape to allow isentropic expansion of every fluid element. Optimization improves the performance, bringing the nozzle thrust to 70.0% of the notional ideal, and total engine thrust (chamber-plus-nozzle) to 94% of the ideal.

detonation↗
NASA NTRSDate not supplied

Evaluating the performance of portable air filter walls for the James Webb Space Telescope launch campaign

The James Webb Space Telescope (JWST) launched from the Centre Spatial Guyanais (CSG) in December 2021. JWST’s requirements permitted processing in International Organization for Standardization (ISO) Class 7 or better facilities, but CSG was only equipped with ISO Class 8 facilities. To temporarily upgrade the air cleanliness in the Payload Processing Facility, Fueling Hall, and Final Assembly Building Encapsulation Hall, NASA provided two portable High Efficiency Particulate Air (HEPA) and carbon filter walls that were used in each location. The walls were comprised of stacks of two modules high and arranged in push-push configurations as shown to be most effective via Computational Fluid Dynamics simulations of expected floor layouts in each facility. After delivery to NASA’s Goddard Space Flight Center in 2020, the walls underwent initial verification measurements inside a cleanroom and validation testing in an uncontrolled area to quantify their improvement of air cleanliness and particle and molecular fallout. Validation testing showed improvements of 83-99% for airborne particle counts, 79-91% for particle fallout, and 50-90% for molecular fallout. The particle improvements were applied to the contamination budget analysis that tracked current and predicted future cleanliness against End-of-Life requirements for JWST’s critical surfaces. At CSG, the walls successfully maintained an ISO Class 7 environment or better within their envelope in each location, despite their presence in ISO Class 8 facilities with dense integration operations.

HEPA, Contamination Control, Filtration↗
NASA NTRS2022

Evaluating the Performance of Portable Air Filter Walls for the James Webb Space Telescope Launch Campaign

The James Webb Space Telescope (JWST) launched from the Centre Spatial Guyanais (CSG) in December 2021. JWST’s requirements permitted processing in International Organization for Standardization (ISO) Class 7 or better facilities, but CSG was only equipped with ISO Class 8 facilities. To temporarily upgrade the air cleanliness in the Payload Processing Facility, Fueling Hall, and Final Assembly Building Encapsulation Hall, NASA provided two portable High Efficiency Particulate Air (HEPA) and carbon filter walls that were used in each location. The walls were comprised of stacks of two modules high and arranged in push-push configurations as shown to be most effective via Computational Fluid Dynamics simulations of expected floor layouts in each facility. After delivery to NASA’s Goddard Space Flight Center in 2020, the walls underwent initial verification measurements inside a cleanroom and validation testing in an uncontrolled area to quantify their improvement of air cleanliness and particle and molecular fallout. Validation testing showed improvements of 83-99% for airborne particle counts, 79-91% for particle fallout, and 50-90% for molecular fallout. The particle improvements were applied to the contamination budget analysis that tracked current and predicted future cleanliness against End-of-Life requirements for JWST’s critical surfaces. At CSG, the walls successfully maintained an ISO Class 7 environment or better within their envelope in each location, despite their presence in ISO Class 8 facilities with dense integration operations.

HEPA, Contamination Control, Filtration↗
NASA NTRS2022

FUN3D Manual: 14.0

This manual describes the installation and execution of FUN3D version 14.0,including optional dependent packages. FUN3D is a suite of computational fluid dynamics simulation and design tools that uses mixed-element unstructured grids in a large number of formats, including structured multiblock and overset grid systems. A discretely-exact adjoint solver may be used for for-mal design optimization, error estimation, and mesh adaptation. FUN3D also offers a reacting, real-gas capability and provides GPU acceleration of many common simulation options.1

William K Anderson↗
NASA NTRSDate not supplied

Operational Techniques in Microgravity for Cryogenic Fluid Management

Management of cryogens in microgravity is a critical challenge for exploration missions to the Moon and Mars. Operational strategies to aid in cryogenic fluid management (CFM) are proposed and demonstrated using computational fluid dynamics simulations. Application of axial settling thrust is an essential – but potentially expensive – tool for CFM. Demonstrations show that its utilization and timing are important during certain unsettling events, such as engine cutoff. At other times, substantial savings can be realized by reducing the average acceleration (through pulsing thrusters, for example). If the metric for reaching a settled condition is a particular number of slosh periods, then fewer settling resources are needed with a lower acceleration. Alternatively, if a target wave amplitude is the settling objective, then a lower average acceleration will also allow for a higher allowable amplitude for the same heat transfer. Savings can also be obtained by rolling the vehicle, which can mitigate lateral slosh. Advantages and disadvantages of anti-slosh baffles are also discussed along with practical examples of their impact on CFM and ullage collapse. Ullage collapse examples are presented along with recommendations for slewing a vehicle with angular and translational acceleration to mitigate mixing between liquid and ullage.

Cryogenic Fluid Management↗
NASA NTRS2023

FUN3D Manual: 14.0.2

This manual describes the installation and execution of FUN3D version 14.0.2, including optional dependent packages. FUN3D is a suite of computational fluid dynamics simulation and design tools that uses mixed-element unstructured grids in a large number of formats, including structured multiblock and overset grid systems. A discretely-exact adjoint solver may be used for formal design optimization, error estimation, and mesh adaptation. FUN3D also offers a reacting, real-gas capability and provides GPU acceleration of many common simulation options.

William K Anderson↗
NASA NTRSDate not supplied

Statistically Consistent Dispersions of Line Loads to Uncertain Integrated Forces and Moments

This work presents a method to generate line loads that are consistent with integrated force and moment constraints, while also following the statistical distribution underlying known line load data. The motivation for this method is to address a particular problem that can arise during the pre-flight analysis of an ascent vehicle. That problem is constructing separate databases, for line loads and integrated aerodynamic coefficients, that contain different data and thus different amounts of quantified uncertainty. A dispersed line load method is described and applied to a data set generated by 29 computational fluid dynamics simulations at various angles of attack and sideslip. The statistical similarity of the generated line loads to the known data is confirmed by using the Maximum Mean Discrepancy 2-sample test. The promising results from this novel method are compared against results from applying an existing line load adjustment procedure to the same data set. Finally, potential future avenues of research are briefly discussed.

Aaron C. Burkhead↗
NASA NTRSDate not supplied

Modeling Low-G Slosh Using Negative Mass

The modeling of the behavior of fluids in low- or microgravity is a field with little validated data but of great interest to space agencies and companies in the face of humanity’s expanding presence beyond low Earth orbit. Efforts to refuel and repair satellites in geostationary orbit require an understanding of the behavior of sloshing fuel in microgravity. The stability of remote sensing equipment and satellites depends on robust fluid slosh dampening or very accurate modeling, and the Artemis program includes the refueling of large landing systems in its architecture. However, current methodologies are quite binary: either use a relatively low-accuracy equivalent mechanical model or use computational fluid dynamics which are not practical for onboard systems due to their relatively high computational cost. In this work, a novel method of tracking the bubble rather than tracking the fuel itself is presented. Computational fluid dynamics simulations are used to validate the model based on available experimental data, and the dynamics of a refueler spacecraft based on Gateway’s Logistics Module are simulated both for the sloshing case and without sloshing considered.

Matthew M. Wittal↗
NASA NTRSDate not supplied

Tiltwing Transition Flight Analysis Using High-Fidelity CFD

Transition from hover to forward flight and vice versa represents the most critical flight phase of tiltwing aircraft. Despite its importance to ensure a safe operation, the aerodynamics of this maneuver are not sufficiently understood. This paper focuses on the study of transition flight for NASA’s six-passenger tiltwing air taxi by means of high-fidelity computational fluid dynamics simulations. On the basis of a static trim solution, four points within the transition corridor are analyzed: transition mode at wing tilt angles of60and44, and airplane mode at airspeeds of110 ktand155 kt. We investigate the balance of forces and moments for rotor-borne and wing-borne regimes, and how rotor-on-rotor and rotor-on-wing interactions affect performance. The simulations indicate that during the early stages of transition, the vortices remain in close proximity to the proprotors, inducing large fluctuations on the order of the mean blade loading. Additionally, the blowing and swirling effects of the proprotor wakes delay flow separation over a portion of the wing. The mid-transition conditions appear to be critical, with extensive regions of separated flow over the wing. In airplane mode, proprotor-wing slipstream effects can be exploited to enhance lift generation. The results of this paper contribute to a deeper understanding of the complex aerodynamic interactions during transition flight to enable a safer and more efficient operation of tiltwing aircraft.

ARMD↗
NASA NTRS2024

FUN3D Manual: 14.1

This manual describes the installation and execution of FUN3D version 14.1, including optional dependent packages. FUN3D is a suite of computational fluid dynamics simulation and design tools that uses mixed-element unstructured grids in a large number of formats, including structured multiblock and overset grid systems. A discretely-exact adjoint solver may be used for formal design optimization, error estimation, and mesh adaptation. FUN3D also offers a reacting, real-gas capability and provides GPU acceleration of many common simulation options.

William K Anderson↗
NASA NTRSDate not supplied

Visualization of Freestream Vortices in the NASA Langley 4-Foot Supersonic Unitary Plan Wind Tunnel

Streamwise vortices present in the freestream of the NASA Langley 4-Foot Supersonic Unitary Plan Wind Tunnel have been observed experimentally for the first time. A high-energy, burst-mode laser system was used to conduct time-resolved planar laser Mie scattering in the freestream of this facility. The freestream of the facility was observed over Mach numbers ranging from 2.4 to 4.6 and (unit) Reynolds number between 3.3 × 10 6 to 14.8 × 10 6 1/m. Apparent vortical structures were observed in the tunnel freestream at Mach numbers ≤ 3 with little difference observed for varying Reynolds number. With further-increasing Mach number, protrusive and oscillatory vertical ‘sprite’ structures were observed emanating from the tunnel floor boundary layer. Neither of these structural phenomena have been observed before experimentally in the facility and act to confirm and inform predictions made in computational fluid dynamic simulations of the facility.

Flow visualization↗
NASA NTRSDate not supplied

Visualization of Freestream Vortices in the NASA Langley 4-Foot Supersonic Unitary Plan Wind Tunnel

Streamwise vortices present in the freestream of the NASA Langley 4-Foot Supersonic Unitary Plan Wind Tunnel have been observed experimentally for the first time. A high-energy, burst-mode laser system was used to conduct time-resolved planar laser Mie scattering in the freestream of this facility. The freestream of the facility was observed over Mach numbers ranging from 2.4 to 4.6 and (unit) Reynolds number between 3.3 × 10 6 to 14.8 × 10 6 1/m. Apparent vortical structures were observed in the tunnel freestream at Mach numbers ≤ 3 with little difference observed for varying Reynolds number. With further-increasing Mach number, protrusive and oscillatory vertical ‘sprite’ structures were observed emanating from the tunnel floor boundary layer. Neither of these structural phenomena have been observed before experimentally in the facility and act to confirm and inform predictions made in computational fluid dynamic simulations of the facility.

Flow visualization↗
NASA NTRSDate not supplied

Fluidic Fence Flow Control on A 30° Swept Wing in Compressible Freestreams

A 30° swept wing with a NACA 64(3)-618 airfoil cross-section was evaluated in four different freestream conditions with Mach numbers increasing from 0.05 to 0.7 using computational fluid dynamics simulations. Active flow control (AFC) through a streamwise row of vortex generating jets was applied at 70% span, blowing inboard to obstruct the development of spanwise flow and increase lift outboard of the control location. The effectiveness of the AFC was evaluated at α = 5° and 10° as freestream Mach number increased and the AFC mass flow coefficient was held constant. Increases to lift coefficient were reduced at higher Mach numbers, but the ratio of change in lift coefficient and the AFC momentum coefficient remained roughly constant. The fluidic fence caused decreased pressure coefficients on the outboard wing sections, but this region of decreased pressure coefficient moved aft on the chord with increasing Mach number. Mach 0.7 is higher than the critical Mach number of the wing and produced interesting interplay with the AFC, as the suction surface shock moved forward on the inboard wing section but moved aft on the outboard wing section.

Evan J McFadden↗
NASA NTRSDate not supplied

Computational Optimization of a Rotary Valved Pulse Combustor Concept

A resonant pulse combustor valve concept is introduced that utilizes two slotted, coaxial counterrotating discs for mechanical actuation at the combustor inlet. The intended test article for prototype demonstration is a small, 22 in. long, propane fueled laboratory combustor, flowing approximately 0.006 lbm/s of air. The objective is to develop an externally actuated (i.e., active) valve that yields better performance and longer life than the traditional internally actuated (i.e., passive), reed-type valve found on most pulse combustors. The rotary valve motion is optimized using an axisymmetric, two-dimensional computational fluid dynamic simulation with a domain that includes the valve as a moveable interior wall. Parameters such as slew rate, dwell period in the open position, and total closed period are varied using fuel specific impulse as the figure of merit. Variations in fuel injector location and air fuel ratio are also examined. Additionally, the performance impact of leakage from the rotary valve is quantified since leakage is endemic to the design. The optimized simulation results indicate that the rotary valve concept can deliver the desired performance attributes using disc rotational speeds and stresses that are well within the realm of modern materials. A preliminary mechanical valve design is included in the report.

pressure gain combustion↗
NASA NTRSDate not supplied

Fluidic Fence Flow Control on A 30° Swept Wing in Compressible Freestreams

A 30° swept wing with a NACA 64(3)-618 airfoil cross-section was evaluated in four different freestream conditions with Mach numbers increasing from 0.05 to 0.7 using computational fluid dynamics simulations. Active flow control (AFC) through a streamwise row of vortex generating jets was applied at 70% span, blowing inboard to obstruct the development of spanwise flow and increase lift outboard of the control location. The effectiveness of the AFC was evaluated at α = 5° and 10° as freestream Mach number increased and the AFC mass flow coefficient was held constant. Increases to lift coefficient were reduced at higher Mach numbers, but the ratio of change in lift coefficient and the AFC momentum coefficient remained roughly constant. The fluidic fence caused decreased pressure coefficients on the outboard wing sections, but this region of decreased pressure coefficient moved aft on the chord with increasing Mach number. Mach 0.7 is higher than the critical Mach number of the wing and produced interesting interplay with the AFC, as the suction surface shock moved forward on the inboard wing section but moved aft on the outboard wing section.

Evan J McFadden↗
NASA NTRSDate not supplied

Computational Optimization of a Rotary Valved Pulse Combustor Concept

A resonant pulse combustor valve concept is introduced that utilizes two slotted, coaxial counterrotating discs for mechanical actuation at the combustor inlet. The intended test article for prototype demonstration is a small, 22 in. long, propane fueled laboratory combustor, flowing approximately 0.006 lbm/s of air. The objective is to develop an externally actuated (i.e., active) valve that yields better performance and longer life than the traditional internally actuated (i.e., passive), reed-type valve found on most pulse combustors. The rotary valve motion is optimized using an axisymmetric, two-dimensional computational fluid dynamic simulation with a domain that includes the valve as a moveable interior wall. Parameters such as slew rate, dwell period in the open position, and total closed period are varied using fuel specific impulse as the figure of merit. Variations in fuel injector location and air fuel ratio are also examined. Additionally, the performance impact of leakage from the rotary valve is quantified since leakage is endemic to the design. The optimized simulation results indicate that the rotary valve concept can deliver the desired performance attributes using disc rotational speeds and stresses that are well within the realm of modern materials. A preliminary mechanical valve design is included in the report.

pressure gain combustion↗
NASA NTRS1984

Feasibility of using the Massively Parallel Processor for large eddy simulations and other Computational Fluid Dynamics applications

The results of an investigation into the feasibility of using the MPP for direct and large eddy simulations of the Navier-Stokes equations is presented. A major part of this study was devoted to the implementation of two of the standard numerical algorithms for CFD. These implementations were not run on the Massively Parallel Processor (MPP) since the machine delivered to NASA Goddard does not have sufficient capacity. Instead, a detailed implementation plan was designed and from these were derived estimates of the time and space requirements of the algorithms on a suitably configured MPP. In addition, other issues related to the practical implementation of these algorithms on an MPP-like architecture were considered; namely, adaptive grid generation, zonal boundary conditions, the table lookup problem, and the software interface. Performance estimates show that the architectural components of the MPP, the Staging Memory and the Array Unit, appear to be well suited to the numerical algorithms of CFD. This combined with the prospect of building a faster and larger MMP-like machine holds the promise of achieving sustained gigaflop rates that are required for the numerical simulations in CFD.

Bruno, John↗