Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “compositional properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Polymer-Infiltrated Metal–Organic Frameworks for Thin-Film Composite Mixed-Matrix Membranes with High Gas Separation Properties

Thin-film composite mixed-matrix membranes (TFC-MMMs) have potential applications in practical gas separation processes because of their high permeance (gas flux) and gas selectivity. In this study, we fabricated a high-performance TFC-MMM based on a rubbery comb copolymer, i.e., poly(2-[3-(2H-benzotriazol-2-yl)-4-hydroxyphenyl] ethyl methacrylate)-co-poly(oxyethylene methacrylate) (PBE), and metal–organic framework MOF-808 nanoparticles. The rubbery copolymer penetrates through the pores of MOF-808, thereby tuning the pore size. In addition, the rubbery copolymer forms a defect-free interfacial morphology with polymer-infiltrated MOF-808 nanoparticles. Consequently, TFC-MMMs (thickness = 350 nm) can be successfully prepared even with a high loading of MOF-808. As polymer-infiltrated MOF is incorporated into the polymer matrix, the PBE/MOF-808 membrane exhibits a significantly higher CO 2 permeance (1069 GPU) and CO 2 /N 2 selectivity (52.7) than that of the pristine PBE membrane (CO 2 permeance = 431 GPU and CO 2 /N 2 selectivity = 36.2). Therefore, the approach considered in this study is suitable for fabricating high-performance thin-film composite membranes via polymer infiltration into MOF pores.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Toward improved PVDF-BaTiO 3 composite dielectrics: mechanical activation of the filler versus filler content

Abstract Barium titanate (BT) perovskite particles were surface modified by means of mechanical treatment and used as inorganic component in polyvinylidene fluoride (PVDF) based composites. The changes in electrical properties of the composite films with increasing in filler content were followed by dielectric spectroscopy, breakdown strength andD-Emeasurements. A comparison of the properties of the composites prepared with untreated and mechanically activated particles revealed that there is a significant difference in their performances at low filler concentrations (<20 wt%). Introduction of the surface modified ceramic particles into PVDF matrix led to an increase of the dielectric constant without affecting significantly the electrical breakdown strength. In contrast, when as received BT particles were used a filler, both dielectric constants and breakdown strengths of the composite films were lower than the corresponding values observed for the pure PVDF. At higher concentrations, however, the influence of pre-treatment of the filler on the effective electrical properties becomes less significant. The obtained results were discussed in terms of the pronounced crystallization of polarβandγcrystal phases of PVDF in the presence of surface modified BT fillers, which is confirmed by Raman spectroscopy.

Physics↗
DOE OSTI2020

Styrene-Based Elastomer Composites with Functionalized Graphene Oxide and Silica Nanofiber Fillers: Mechanical and Thermal Conductivity Properties

The mechanical and thermal conductivity properties of two composite elastomers were studied. Styrene–butadiene rubber (SBR) filled with functionalized graphene oxide (GO) and silica nanofibers, and styrene–butadiene–styrene (SBS) block copolymers filled with graphene oxide. For the SBR composites, GO fillers with two different surface functionalities were synthesized (cysteamine and dodecylamine) and dispersed in the SBR using mechanical and liquid mixing techniques. The hydrophilic cysteamine-based GO fillers were dispersed in the SBR by mechanical mixing, whereas the hydrophobic dodecylamine-based GO fillers were dispersed in the SBR by liquid mixing. Silica nanofibers (SnFs) were fabricated by electrospinning a sol–gel precursor solution. The surface chemistry of the functionalized fillers was studied in detail. The properties of the composites and the synergistic improvements between the GO and SnFs are presented. For the SBS composites, GO fillers were dispersed in the SBS elastomer at several weight percent loadings using liquid mixing. Characterization of the filler material and the composite elastomers was performed using x-ray photoelectron spectroscopy, x-ray diffraction, transmission electron microscopy, scanning electron microscopy, thermogravimetric analysis, dynamic mechanical analysis, tensile testing, nanoindentation, thermal conductivity and abrasion testing.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Quantitative assessment of particle dispersion in polymeric composites and its effect on mechanical properties

In this work, an automated image analysis tool is developed to establish quantitative correlations between the particle/cluster size distribution and the mechanical properties of particle reinforced polymer composites (PRPC).This automated image analysis tool is developed within python programming software to process and analyze the microstructural images of the polymerbased composite materials. The spent coffee bean powder (SCBP) reinforced poly-propylene carbonate (PPC) polymer composite with differing wt.% of the filler is selected for the analysis. Detailed statistical analysis of the microstructural images reveals that ‘clustering of clusters’ is also presented in addition to the most commonly reported ‘clustering of particles’, and the distribution of particle/clusters is bimodal. Based on these findings, an effective volume fraction for the filler material is proposed to mainly capture the agglomeration effect. With this effective volume fraction, the standard rule-of-mixture model correctly captures the experimentally measured tensile strength and modulus as a function of filler wt.%. Further, the applicability of this effective volume fraction for other theoretical models is also analyzed. The detailed statistical analysis of the microstructure and the proposed effective volume fraction helps to develop a deeper quantitative understanding of the PRPC than the conventional qualitative correlation of microstructural features with the properties and failure processes.

36 MATERIALS SCIENCE↗
DOE OSTI2020

On the Use of Surfactant-Complexed Chitosan for Toughening 3D Printed Polymethacrylate Composites

This work reports a simple approach to prepare toughened 3D-printed polymethacrylate (PMA) composites using surfactant-modified chitosan (SMCS) particles at loadings between 2–10 wt%. Chitosan (CS) is modified with anionic surfactant, sodium dodecyl sulfate, via ionic complexation to facilitate compatibility and dispersion of CS to PMA matrix by non-covalent interactions between the components. The study successfully demonstrates high-accuracy 3D printing of composites with significant improvements in the overall mechanical properties. The composite with the best loading of 8 wt% SMCS shows a tensile modulus of 1.23 ± 0.05 GPa, a tensile strength at 49.8 ± 0.96 MPa, a yield stress at 33.3 ± 1.48 MPa, and a strain-at-ailure 10.3 ± 0.61%, which are 45%, 40%, 32%, and 68% higher than neat PMA, respectively. This provides a significant improvement in toughness at 4.92 ± 0.55 MJ m -3 for the composite, 184% higher than that of neat PMA. The marked increase in toughness is due to enhanced filler-matrix interactions which improve the ability of the 3D printed composite to absorb energy under tensile load. The results from this work provide new understandings into the strategies for design and preparation of stereolithography 3D printed materials reinforced with toughening fillers from renewable resources.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Effect of vanadium on phase composition and hard magnetic properties of as-solidified and heat-treated Sm–Fe–(Ti,V) alloys

Although the intrinsic magnetic properties of Ti-stabilized Sm(Fe,Co,Ti) 12 compounds exhibit potential of excellent rare-earth-lean permanent magnets, it has been much easier to realize large coercivities with the isostructural compounds stabilized by either V or by certain combinations of Ti and V. To elucidate the influence of V on the microstructure and magnetic properties, a series of Sm 8.1 Fe 78.4 (Ti 1-x V x ) 13.5 alloys was studied after arc-melting and annealing at 850–1000 °C. The alloys were found to fall into three groups. For x ≤ 0.2, solidification generates mostly the Sm(Fe,Ti,V) 12 phase, but annealing converts at least part of it into the non-magnetic Sm(Fe,Ti,V) 11 and the magnetically soft Sm 2 (Fe,Ti,V) 17 phases. For 0.2 < x < 0.6, the alloys solidify into a near-equilibrium mixture of the Sm(Fe,Ti,V) 12 , TiFe 2 and Sm-rich phases. For x ≥ 0.6, solidification generates large fractions of α-Fe solid solution and Sm-rich phases; an annealing step is necessary to complete the formation of Sm(Fe,Ti,V) 12 phase. Also, for x ≥ 0.6 the temperature below which the Sm(Fe,Ti,V) 12 phase is stable decreases with x, as does the fraction of this phase formed during solidification. Here, the differences between these three groups of alloys suggest different strategies for developing hard magnetic properties, with the likelihood of a success increasing with increasing x. For x ≥ 0.6, heat treatment alone is demonstrated to generate a microstructure of micron and submicron Sm(Fe,Ti 1-x V x ) 12 crystallites separated by a Sm-rich phase and exhibiting a coercivity with values up to 3.5 and 5.7 kOe for x = 0.8 and 1.0, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Ceramic–Metal (Cermet) Composites: A Review of Key Properties and Synthesis Methods Focused on Nuclear Waste Immobilization

Here this paper reviews key properties, applications, and examples of ceramic-metal composites (cermets), and metal matrix composites (MMC) with emphasis on their applicability as waste forms for immobilizing nuclear waste. While the literature is mature for vitrified and cementitious radioactive waste forms, cermet materials have not received adequate attention as potential candidates for immobilizing nuclear waste. To promulgate this effort, this review connects cermet and MMC design, such as hardened tools, with the chemistry of radioactive waste streams. A discussion on certification and qualification standards for cermet waste forms, literature gaps, and “how-to” sections on cermet processing techniques. Key parameters discussed include thermal conductivity, chemical durability, and waste loading, as well as examples for metal-containing waste forms. As cermet waste forms gain momentum within the community, this review paper aims ensure the end-of-life nuclear fuel cycle is addressed from a materials and waste disposition perspective.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Compositional Tuning of Magnetic Properties in a Series of Transition Metal Site-Deficient UCo x Bi 2 and UNi x Bi 2 Phases

Varying the electronic structure of topological materials through aliovalent substitution is a primary approach to tuning their physical properties. Unlike substitution, metal site deficiency intrinsic to some structure types, including HfCuSi 2 -type, has rarely been employed for controlling the properties of topological phases. In this report, we describe the synthesis and characterization of two new series of compounds, UCoxBi 2 and UNixBi 2 , which demonstrate the variation of transition metal content through synthetic conditions. Magnetic measurements reveal the dependence between the extent of transition metal incorporation and the magnetism of the resulting phase. DFT calculations demonstrated the ability to model their formation and predict the stability ranges of transition metal-site deficient compounds.

Crystal structure↗
DOE OSTI2023

Characterizing the composition, structure, and mechanical properties of magnetron sputtering physical vapor deposition TiN and TiSiN coatings

Ti(Si)N coatings were deposited on Si wafers via magnetron sputtering physical vapor deposition technique. Scanning electron microscopy and atomic force microscopy were used to study the morphologies, grain size, and thicknesses of the different films. X-ray diffraction confirmed the formation of the titanium nitride cubic phase. X-ray photoelectron spectroscopy (XPS) was used to study the silicon and oxygen levels in the films, and high resolution XPS was used to determine the surface oxide to nitride ratios as well as the silicon–nitrogen environment. The hardness of these films was then determined with nanoindentation. It was shown that grain size and film density could be controlled by the Si level and the ion bombardment to eliminate the oxygen level in the nitride coatings, which led to the harder films. It was suggested that due to the miscibility of Si, a ternary TiSiN solid solution was formed. Stronger (200) orientation of the TiN B1-NaCl crystals was associated with increased hardness of the coatings. In conclusion, this crystalline structure was preserved after incorporating Si.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A Comparative Study of Imidazolium-Based Ionic Liquid-Single-Walled Carbon Nanotube Composites with Enhanced Conductivity Properties for Supercapacitor Applications

Mixtures of ionic liquids (ILs) containing single-walled carbon nanotubes (SWCNTs) were prepared and characterized to obtain electrolytes with optimized transport properties for use in energy storage devices such as supercapacitors. Imidazolium ILs bearing cations with side chains of different functionality coupled with bis(trifluoromethylsulfonyl)amide (NTf 2- ) or bis(fluorosulfonyl)-amide (FSA-) anions, were used in mixtures containing up to 5 wt% SWCNTs. At and above 2 wt% nanotube loading, the mixtures exhibited higher conductivities than the pure ILs, in spite of the extremely high viscosities. Loadings of 5 wt% produced very high conductivities, and studies of the temperature dependence indicated a change in the charge transport mechanism between 2 and 5 wt% loading. At 5 wt% loading, the highest conductivities (up to 540 mS/cm at 25 °C) were obtained for the ILs containing the NTf 2- anion. Overall, these results can significantly contribute to the development of improved energy storage devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗