Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “characterization and analytical techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Compound Specific Hydrogen Isotope Composition of Type II and III Kerogen Extracted by Pyrolysis-GC-MS-IRMS

The use of Hydrogen (H) isotopes in understanding oil and gas resource plays is in its infancy. Described here is a technique for H isotope analysis of organic compounds pyrolyzed from oil and gas shale-derived kerogen. Application of this technique will progress our understanding. This work complements that of Pernia et al. (2013, this meeting) by providing a novel method for the H isotope analysis of specific compounds in the characterization of kerogen extracted by analytically diverse techniques. Hydrogen isotope analyses were carried out entirely "on-line" utilizing a CDS 5000 Pyroprobe connected to a Thermo Trace GC Ultra interfaced with a Thermo MAT 253 IRMS. Also, a split of GC-separated products was sent to a DSQ II quadrupole MS to make semi-quantitative compositional measurements of the extracted compounds. Kerogen samples from five different basins (type II and III) were dehydrated (heated to 80 C overnight in vacuum) and analyzed for their H isotope compositions by Pyrolysis-GC-MS-TC-IRMS. This technique takes pyrolysis products separated via GC and reacts them in a high temperature conversion furnace (1450 C) which quantitatively forms H2, following a modified method of Burgoyne and Hayes, (1998, Anal. Chem., 70, 5136-5141). Samples ranging from approximately 0.5 to 1.0mg in size, were pyrolyzed at 800 C for 30s. Compounds were separated on a Poraplot Q GC column. Hydrogen isotope data from all kerogen samples typically show enrichment in D from low to high molecular weight compounds. Water (H2O) average deltaD = -215.2 (V-SMOW), ranging from -271.8 for the Marcellus Shale to -51.9 for the Polish Shale. Higher molecular weight compounds like toluene (C7H8) have an average deltaD of -89.7 0/00, ranging from -156.0 for the Barnett Shale to -50.0 for the Monterey Shale. We interpret these data as representative of potential H isotope exchange between hydrocarbons and sediment pore water during formation within each basin. Since hydrocarbon H isotopes readily exchange with water, these data may provide some useful information on gas-water or oil-water interaction in resource plays, and further as a possible indicator of paleo-environmental conditions. Alternatively, our data may be an indication of H isotope exchange with water and/or acid during the kerogen isolation process. Either of these interpretations will prove useful when deciphering H isotope data derived from kerogen analysis. More experiments are planned to discern these two or other possible scenarios.

Socki, Richard A.↗
DOE OSTI2022

Synthesis of La 2–x Sr x CuO 4 films via atomic layer-by-layer molecular beam epitaxy

Atomic layer-by-layer molecular beam epitaxy (ALL-MBE) is a sophisticated technique to synthesize high-temperature superconductor (HTS) materials. ALL-MBE produces single-crystal HTS films with atomically smooth surfaces and interfaces, as well as precise multilayer heterostructures engineered down to a single atomic layer level. This enables the fabrication of tunnel junctions, nanowires, nanorings, and other HTS devices of interest. Our group has focused on ALL-MBE synthesis and materials science of La 2–x Sr x CuO 4 (LSCO), a representative HTS cuprate. In the past two decades, we have synthesized over three thousand LSCO thin films and characterized them by a range of analytical techniques. Here, we present in full detail a systematic process for the synthesis and engineering of atomically perfect LSCO films. The procedure includes the preparation of substrates, calibration of the elemental sources, the recipe for ALL growth of LSCO films without any secondary-phase precipitates, post-growth annealing of the films, and ex situ film characterization. This report should aid replication and dissemination of this technique of synthesizing single-crystal LSCO films for basic research as well as for HTS electronic applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2009

XPS Protocol for the Characterization of Pristine and Functionalized Single Wall Carbon Nanotubes

Recent interest in developing new applications for carbon nanotubes (CNT) has fueled the need to use accurate macroscopic and nanoscopic techniques to characterize and understand their chemistry. X-ray photoelectron spectroscopy (XPS) has proved to be a useful analytical tool for nanoscale surface characterization of materials including carbon nanotubes. Recent nanotechnology research at NASA Johnson Space Center (NASA-JSC) helped to establish a characterization protocol for quality assessment for single wall carbon nanotubes (SWCNTs). Here, a review of some of the major factors of the XPS technique that can influence the quality of analytical data, suggestions for methods to maximize the quality of data obtained by XPS, and the development of a protocol for XPS characterization as a complementary technique for analyzing the purity and surface characteristics of SWCNTs is presented. The XPS protocol is then applied to a number of experiments including impurity analysis and the study of chemical modifications for SWCNTs.

Sosa, E. D.↗
NASA NTRS1992

Resin transfer molding of textile preforms for aircraft structural applications

The NASA LaRC is conducting and supporting research to develop cost-effective fabrication methods that are applicable to primary composite aircraft structures. One of the most promising fabrication methods that has evolved is resin transfer molding (RTM) of dry textile material forms. RTM has been used for many years for secondary structures, but has received increased emphasis because it is an excellent method for applying resin to damage-tolerant textile preforms at low cost. Textile preforms based on processes such as weaving, braiding, knitting, stitching, and combinations of these have been shown to offer significant improvements in damage tolerance compared to laminated tape composites. The use of low-cost resins combined with textile preforms could provide a major breakthrough in achieving cost-effective composite aircraft structures. RTM uses resin in its lowest cost form, and storage and spoilage costs are minimal. Near net shape textile preforms are expected to be cost-effective because automated machines can be used to produce the preforms, post-cure operations such as machining and fastening are minimized, and material scrap rate may be reduced in comparison with traditional prepreg molding. The purpose of this paper is to discuss experimental and analytical techniques that are under development at NASA Langley to aid the engineer in developing RTM processes for airframe structural elements. Included are experimental techniques to characterize preform and resin behavior and analytical methods that were developed to predict resin flow and cure kinetics.

Hasko, Gregory H.↗
DOE OSTI2025

In-situ monitoring of atomically dispersed Pt sites supported on OMS-2 during CO 2 activation

Atomically dispersed catalysts have drawn great interest lately, as they showcase a high density of active sites, selectivity, and high turnover frequencies in oxidation chemistry due to labile oxygen activation. In contrast, the applications of these catalysts have lagged in reduction reactions due to the ambiguity caused by the sintering and restructuring of active sites. To bridge this gap, the evolution of Pt 4+ isomorphically substituted into an octahedral molecular sieve structure (OMS-2) under reductive conditions was correlatively characterized using multiple in-situ analytical techniques such as ambient pressure X-ray photoelectron spectroscopy, environmental transmission electron microscopy, and solid-state nuclear magnetic resonance. The surface dynamics of the Pt single atoms were revealed during the Reverse Water Gas Shift (RWGS) reaction, where the active sites were identified as two-coordinated platinum single atoms. Under reaction, we show nonbinding atoms adjacent to the single atoms restructured the motif of the single atoms to Pt 2+ via ion mobility of potassium, increasing the activation energy by 25.6 kJ/mol. Here, this work also highlights the potential for increased stability of the single atom sites via isomorphic substitution of the metal oxide support, since the Pt-OMS-2 catalyst retained activity for about 33 h before deactivation, after which nanoparticles were observed in TEM images. This work offers a new perspective in single atom synthesis using the metal oxide as the host for the single atom site, instead of adatoms on the surface

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

A survey study on arsenic speciation in coal fly ash and insights into the role of coal combustion conditions

Coal fly ashes (CFAs) are the low-density byproducts of the coal combustion process. Improper or uncontrolled CFA disposal poses significant environmental and health concerns due to the potential leaching of toxic heavy metals such as arsenic (As). Previous studies have investigated the content and speciation of As in different CFA samples, yet systematic information on As speciation in CFA with representative coal source and combustion conditions is still missing. Based on a recent survey study on the typical coal sources and combustion conditions across the U.S., this study selected 19 representative CFA samples to systematically investigate As speciation and potential correlations with these parameters. The composition, morphology, mineralogy, and As speciation of these CFA samples were characterized by complementary analytical, microscopic, and spectroscopic techniques. Synchrotron X-ray spectroscopy and microscopy analyses revealed the dominant As oxidation state to be As(V) and with strong associations to Ca, with the exception of 3 samples that had 19–51% As(III), likely due to the use of selective catalytic reduction (SCR) process. Principal component analysis was conducted to identify potential correlations of As concentration and oxidation state with parameters such as major element content, loss on ignition (LOI), average particle size, coal source, and combustion condition. Al 2 O 3 and FeO content were found to capture a majority of the variability. Further, results from this study provide fundamental basis for understanding the correlations between coal source, combustion conditions, CFA characteristics, and As speciation, and providing insights for downstream beneficial utilization or disposal management.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Leveraging Nitrogen Linkages in the Formation of a Porous Thorium–Organic Nanotube Suitable for Iodine Capture

We report the synthesis, characterization, and iodine capture application of a novel thorium–organic nanotube, TSN-626, [Th 6 O 4 (OH) 4 (C 6 H 4 NO 2 ) 7 (CHO 2 ) 5 (H 2 O) 3 ]·3H 2 O. The classification as a metal–organic nanotube (MONT) distinguishes it as a rare and reduced dimensionality subset of metal–organic frameworks (MOFs); the structure is additionally hallmarked by low node connectivity. TSN-626 is composed of hexameric thorium secondary building units and mixed O/N-donor isonicotinate ligands that demonstrate selective ditopicity, yielding both terminating and bridging moieties. Because hard Lewis acid tetravalent metals have a propensity to bind with electron donors of rival hardness (e.g., carboxylate groups), such Th–N coordination in a MOF is uncommon. However, the formation of key structural Th–N bonds in TSN-626 cap some of the square antiprismatic metal centers, a position usually occupied by terminal water ligands. TSN-626 was characterized by using complementary analytical and computational techniques: X-ray diffraction, vibrational spectroscopy, N 2 physisorption isotherms, and density functional theory. TSN-626 satisfies design aspects for the chemisorption of iodine. The synergy between accessibility through pores, vacancies at the metal–oxo nodes, and pendent N-donor sites allowed a saturated iodine loading of 955 mg g –1 by vapor methods. Furthermore, the crystallization of TSN-626 diversifies actinide–MOF linker selection to include soft electron donors, and these Th–N linkages can be leveraged for the investigation of metal-to-ligand bonding and unconventional topological expressions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Exploring the First High-Entropy Thin Film Libraries: Composition Spread-Controlled Crystalline Structure

Thin films of two types of high-entropy oxides (HEOs) have been deposited on 76.2 mm Si wafers using combinatorial sputter deposition. In one type of the oxides, (MgZnMnCoNi)O x , all the metals have a stable divalent oxidation state and similar cationic radii. In the second type of oxides, (CrFeMnCoNi)O x , the metals are more diverse in the atomic radius and valence state, and have good solubility in their sub-binary and ternary oxide systems. Therefore, the resulting HEO thin films were characterized using several high-throughput analytical techniques. The microstructure, composition, and electrical conductivity obtained on defined grid maps were obtained for the first time across large compositional ranges. The crystalline structure of the films was observed as a function of the metallic elements in the composition spreads, that is, the Mn and Zn in (MgZnMnCoNi)O x and Mn and Ni in (CrFeMnCoNi)O x . The (MgZnMnCoNi)O x sample was observed to form two-phase structures, except single spinel structure was found in (MgZnMnCoNi)O x over a range of Mn > 12 at. % and Zn < 44 at. %, while (CrFeMnCoNi)O x was always observed to form two-phase structures. Composition-controlled crystalline structure is not only experimentally demonstrated but also supported by density function theory calculation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Radiation-Induced Modifications in Copper Oxide Growth

Radiation-induced effects and their influence on oxidation processes were evaluated for their use as a forensic tool for special nuclear material (SNM). A beam of 10 MeV Au³⁺ ions was used to mimic the accumulation of microstructural damage from self-irradiation through the decay of radionuclides. Several copper samples were irradiated as suitable surrogate materials at 200 °C with a flux of 1x10¹² ions/cm·s to damage levels of 5, 10, and 15 displacements per atom (dpa). This corresponds to about 50, 100, and 150 years, respectively, of accumulated α-decay damage in a PuGa alloy assuming a damage rate of 0.1 dpa/year. After irradiation, all samples were exposed to an accelerated aging process induced by thermal treatment at 350 °C for 1 hour in air. This resulted in the growth of a mixed oxide layer (Cu₂O and CuO) which was characterized in detail using several complementary analytical techniques: Scanning Electron Microscopy, Raman spectroscopy, Synchrotron X-ray diffraction (transmission mode), and Grazing Incidence X-ray diffraction. The oxide layer growth of irradiated Cu at 350°C is distinctly modified as a result of the ion irradiation. Most notably, the growth of the CuO phase is suppressed with increasing radiation damage on the Cu substrate, and structural changes occurred in the Cu₂O phase. These results indicate that damage from self-irradiation over time can cause quantifiable modifications in the oxidation process of metals that could be harnessed for their use as a novel forensic tool.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Leaching of Rare Earth Elements from Central Appalachian Coal Seam Underclays

Rare earth elements (REE) are necessary for advanced technological and energy applications. To support the emerging need, it is necessary to identify new domestic sources of REE and technologies to separate and recover saleable REE product in a safe and economical manner. Underclay rock associated with Central Appalachian coal seams and prevalent in coal utilization waste products is an alternative source of REE to hard rock ores that are mainly composed of highly refractory REE-bearing minerals. This study utilizes a suite of analytical techniques and benchtop leaching tests to characterize the properties and leachability of the coal seam underclays sampled. Laboratory bench-top and flow-through reactor leaching experiments were conducted on underclay rock powders to produce a pregnant leach solution (PLS) that has relatively low concentrations of gangue elements Al, Si, Fe, and Th and is amenable to further processing steps to recover and produce purified REE product. The leaching method described here uses a chelating agent, the citrate anion, to solubilize elements that are adsorbed, or weakly bonded to the surface of clay minerals or other mineral solid phases in the rock. The citrate PLS produced from leaching specific underclay powders contains relatively higher concentrations of REE and lower concentrations of gangue elements compared to PLS produced from sequential digestion using ammonium sulfate and mineral acids. Citrate solution leaching of underclay produces a PLS with lower concentrations of gangue elements and higher concentrations of REE than achieved with hydrochloric acid or sulfuric acid. The results provide a preliminary assessment of the types of REE-bearing minerals and potential leachability of coal seam underclays from the Central Appalachian basin.

58 GEOSCIENCES↗
DOE OSTI2025

Metasurfaces with Multipolar Resonances and Enhanced Light–Matter Interaction

Metasurfaces, composed of engineered nanoantennas, enable unprecedented control over electromagnetic waves by leveraging multipolar resonances to tailor light–matter interactions. This review explores key physical mechanisms that govern their optical properties, including the role of multipolar resonances in shaping metasurface responses, the emergence of bound states in the continuum (BICs) that support high-quality factor modes, and the Purcell effect, which enhances spontaneous emission rates at the nanoscale. These effects collectively underpin the design of advanced photonic devices with tailored spectral, angular, and polarization-dependent properties. This review discusses recent advances in metasurfaces and applications based on them, highlighting research that employs full-wave numerical simulations, analytical and semi-analytic techniques, multipolar decomposition, nanofabrication, and experimental characterization to explore the interplay of multipolar resonances, bound and quasi-bound states, and enhanced light–matter interactions. A particular focus is given to metasurface-enhanced photodetectors, where structured nanoantennas improve light absorption, spectral selectivity, and quantum efficiency. By integrating metasurfaces with conventional photodetector architectures, it is possible to enhance responsivity, engineer photocarrier generation rates, and even enable functionalities such as polarization-sensitive detection. The interplay between multipolar resonances, BICs, and emission control mechanisms provides a unified framework for designing next-generation optoelectronic devices. This review consolidates recent progress in these areas, emphasizing the potential of metasurface-based approaches for high-performance sensing, imaging, and energy-harvesting applications.

Kerker effect↗
NASA NTRS1986

Analyses of spacecraft polymeric materials

Partial analytical characterizations are made by four different techniques of three polymeric materials used in conjunction with the Space Telescope for samples flown on mission STS-8. The polymers were Tedlar, Kapton H, and Kapton F. The surfaces of the three polymers were attacked and oxidized by atomic oxygen, and fluorine is lost from the surface of Kapton F, largely due to displacement by atomic oxygen.

Worley, S. D.↗
NASA NTRS2003

Functionalization of Carbon Nanotubes

These project will explore the functionalization of carbon nanotubes via the formation of molecular complexes with perylene diimide based systems. It is anticipated that these complexes would be soluble in organic solvent and enable the homogenous dispersion of carbon nanotubes in polymer films. Molecular complexes will be prepared and characterized using standard spectroscopic and thermal analytical techniques. Polymer films will be prepared with these complexes and their properties (electrical and thermal conductivity, mechanical properties, stability) evaluated.

Webber, Stephen E.↗
DOE OSTI2021

BETO 2021 Peer Review - FCIC Task 6: High Temperature Conversion

The impacts of feedstock variability on pyrolysis processes are significant but poorly defined. Current engineering designs are based on empirical guidelines, useful only over a narrow range of feedstock properties. The objectives of this project are to (1) Develop science-based knowledge of how feedstock attributes and operational parameters impact pyrolysis process reliability and product quality; and (2) Build an experimental and computational toolset that predicts these outcomes, enabling processes to optimize reliability and product quality. Biomass is a complex feedstock. Controlling for and testing the effects of individual attributes is very challenging. This project couples multiscale experimentation and modeling to accurately capture the fundamental physics and chemistry of biomass flow and conversion behavior in feeding and pyrolysis reactor operations. Our focus is on pine residue attributes – anatomical fraction (bark, needles, wood), particle morphology (size/shape distribution, density, porosity), and chemical composition (extractives, biopolymers, alkali metals) – that impact product quality for downstream catalytic upgrading. Because detailed pyrolysis product characterization is limited, cutting-edge analytical techniques are being developed to reveal impactful product attributes. The tools and knowledge developed here will enable integrated pyrolysis-based processes that are more robust, flexible, and market-responsive with respect to feedstock variability.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

Pilot-scale hydrotreating of catalytic fast pyrolysis biocrudes: process performance and product analysis

Catalytic fast pyrolysis (CFP) is a technology option for producing advanced biofuels from hydrocarbon-rich biocrude intermediates. The relatively high oxygen content of biocrudes compared to petroleum intermediates increases hydrogen consumption and the lower thermal stability accelerates catalyst deactivation and reactor fouling hindering the adaptation of hydrotreating technology for biocrude upgrading into biofuels. In this study, four chemically different biocrude feeds were upgraded in a pilot scale hydroprocessing unit at similar process conditions using a commercial hydrodeoxygenation (HDO) catalyst. The biocrude feeds and hydrotreated products were characterized using standard ASTM procedures and advanced analytical techniques (GCxGC-FID and GCxGC-MS). HDO catalyst activity was monitored by changes in physical properties and chemical composition of the upgraded products as a function of time on stream. Aliphatic acids, ketones, aldehydes, and furan derivatives were completely converted during the hydrotreating tests while the concentration of aromatics, aliphatic hydrocarbons and phenolics increased during the hydrotreating tests. The oxygen content, nitrogen content, specific gravity, viscosity and the heavy end of the boiling point range (determined by simulated distillation) of the upgraded products increased with increasing time on stream during hydrotreating. The deactivation rate was the lowest for the biocrude feed that contained the most aliphatic and aromatic hydrocarbons and was the highest for the biocrude feed that had the most anhydrosugars. Overall, the HDO deactivation rate correlates with the total amount of oxygen in the feed (17 wt% to 29 wt%, on a wet basis).

09 BIOMASS FUELS↗
NASA NTRS1982

Reduction of chromium in Ni-base superalloys through element substitution and rapid solidification processing

The reduction in the use of Cr in Ni base superalloys by the combined approaches of both elemental substitution and rapid solidification processing is studied. The elements Si, Zr, Y and Hf were chosen as potential partial substitutes for Cr in Waspaloy and IN 713LC sine their separate addition to other alloys has previously resulted in enhanced oxidation resistance. The roles of Cr and these replacement elements in determining the microstructure and properties are evaluated. The elements Si, Zr, and Y and Hf are used as partial replacements for Cr in the base superalloys and these resultant alloys are processed using rapid solidification techniques. The mechanical properties and oxidation resistance of the processed materials are evaluated. The microstructure is characterized using state of the art techniques (e.g. analytical transmission electron microscopy), and the mechanism by which these structures are produced is determined.

Fraser, H. D.↗
NASA NTRSDate not supplied

Evaluating Crystallinity in Thermoplastic Composites for Aerospace Applications

Polymer matrix composites (PMCs) offer many benefits for the aerospace industry due to their potential for weight reduction when compared to metal or ceramic based materials. Most PMCs currently in flight use thermoset matrices, however, thermoplastic resins are being explored as alternatives due to their ability to be remelted, which is of particular interest due to the potential for in-situ repair and faster production. Most thermoplastic resins are semicrystalline polymers. The properties of semicrystalline thermoplastics are directly influenced by their crystallinity, which can vary due to many factors including thermal treatments, environmental conditions, and mechanical deformation. Within thermoplastic PMC parts, crystallinity gradients can arise due to variations in part geometry, across part thicknesses, and along bonded joints. Monitoring the crystallinity of thermoplastic composites is key to ensuring these materials meet the high demands required for aerospace. Several different analytical techniques exist that can be used to characterize the bulk crystallinity of thermoplastic materials. However, many existing methods lack the specificity required to identify the subtle variations in crystallinity that may play a significant role in the performance and durability of PMC parts. Because of this, a significant amount of work is still required to fully characterize and understand the crystallinity profiles of thermoplastic PMCs and the resulting impact to material properties. This talk discusses the use of multiple techniques such as Differential Scanning Calorimetry, Polarized Light Optical Microscopy, and Fourier-Transform Infrared Spectroscopy to characterize the crystallinity in carbon fiber/thermoplastic composites. Samples of different crystallinity profiles were manufactured using various cooling procedures. This work aims to provide the fundamental data necessary to understand the effects of crystallinity on thermoplastic PMCs, which is key to advancing their use in aerospace applications.

Thermoplastics↗