SEARCH · Engineering Papers

Results for “building extraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS2016

Post-Test Inspection of NASA's Evolutionary Xenon Thruster Long-Duration Test Hardware: Discharge and Neutralizer Cathodes

The NEXT Long-Duration Test is part of a comprehensive thruster service life assessment intended to demonstrate overall throughput capability, validate service life models, quantify wear rates as a function of time and operating condition, and identify any unknown life-limiting mechanisms. The test was voluntarily terminated in February 2014 after demonstrating 51,184 hours of high-voltage operation, 918 kg of propellant throughput, and 35.5 MN-s of total impulse. The post-test inspection of the thruster hardware began shortly afterwards with a combination of non-destructive and destructive analysis techniques, and is presently nearing completion. This paper presents relevant results of the post-test inspection for both discharge and neutralizer cathodes. Discharge keeper erosion was found to be significantly reduced from what was observed in the NEXT 2 kh wear test and NSTAR Extended Life Test, providing adequate protection of vital cathode components throughout the test with ample lifetime remaining. The area of the discharge cathode orifice plate that was exposed by the keeper orifice exhibited net erosion, leading to cathode plate material building up in the cathode-keeper gap and causing a thermally-induced electrical short observed during the test. Significant erosion of the neutralizer cathode orifice was also found and is believed to be the root cause of an observed loss in flow margin. Deposition within the neutralizer keeper orifice as well as on the downstream surface was thicker than expected, potentially resulting in a facility-induced impact on the measured flow margin from plume mode. Neutralizer keeper wall erosion on the beam side was found to be significantly lower compared to the NEXT 2 kh wear test, likely due to the reduction in beam extraction diameter of the ion optics that resulted in decreased ion impingement. Results from the post-test inspection have led to some minor thruster design improvements.

Electric Propulsion↗

NASA NTRS2021

Post-test Inspection of NASA’s Evolutionary Xenon Thruster Long-Duration Test Hardware: Discharge and Neutralizer Cathodes

The NEXT Long-Duration Test is part of a comprehensive thruster service life assessment intended to demonstrate overall throughput capability, validate service life models, quantify wear rates as a function of time and operating condition, and identify any unknown life-limiting mechanisms. The test was voluntarily terminated in February 2014 after demonstrating 51,184 h of high-voltage operation, 918 kg of propellant throughput, and 35.5 MN-s of total impulse. The post-test inspection of the thruster hardware began shortly afterwards with a combination of non-destructive and destructive analysis techniques, and is presently nearing completion. This paper presents relevant results of the post-test inspection for both discharge and neutralizer cathodes. Discharge keeper erosion was found to be significantly reduced from what was observed in the NEXT 2 kh wear test and NSTAR Extended Life Test, providing adequate protection of vital cathode components throughout the test with ample lifetime remaining. The area of the discharge cathode orifice plate that was exposed by the keeper orifice exhibited net erosion, leading to cathode plate material building up in the cathode-keeper gap and causing a thermally-induced electrical short observed during the test. Significant erosion of the neutralizer cathode orifice was also found and is believed to be the root cause of an observed loss in flow margin. Deposition within the neutralizer keeper orifice as well as on the downstream surface was thicker than expected, potentially resulting in a facility-induced impact on the measured flow margin from plume mode. Neutralizer keeper wall erosion on the beam side was found to be significantly lower compared to the NEXT 2 kh wear test, likely due to the reduction in beam extraction diameter of the ion optics that resulted in decreased ion impingement. Results from the post-test inspection have led to some minor thruster design improvements.

Ion engine↗

NASA NTRS2015

Formal Foundations for Hierarchical Safety Cases

Safety cases are increasingly being required in many safety-critical domains to assure, using structured argumentation and evidence, that a system is acceptably safe. However, comprehensive system-wide safety arguments present appreciable challenges to develop, understand, evaluate, and manage, partly due to the volume of information that they aggregate, such as the results of hazard analysis, requirements analysis, testing, formal verification, and other engineering activities. Previously, we have proposed hierarchical safety cases, hicases, to aid the comprehension of safety case argument structures. In this paper, we build on a formal notion of safety case to formalise the use of hierarchy as a structuring technique, and show that hicases satisfy several desirable properties. Our aim is to provide a formal, theoretical foundation for safety cases. In particular, we believe that tools for high assurance systems should be granted similar assurance to the systems to which they are applied. To this end, we formally specify and prove the correctness of key operations for constructing and managing hicases, which gives the specification for implementing hicases in AdvoCATE, our toolset for safety case automation. We motivate and explain the theory with the help of a simple running example, extracted from a real safety case and developed using AdvoCATE.

Hierarchy↗

NASA NTRS1988

Using AGNESS (A Generalized Network-based Expert System Shell) for matching images

The image correspondence problem is considered the most difficult step in both stereo and motion analysis. Stereo vision is useful in determining the 3-D positions of points on visible surface in a scene. Motion analysis is useful in determining the spatial and temporal relationships of objects in an environment. Besides stereo and motion analysis, there is the image correspondence problem. Most of this work is based on point or local area properties of the observed gray level values in 2-D images. A global and general approach to this problem is described by using a knowledge-based system. The knowledge it uses consists of both physical properties and spatial relationships of the edges and regions extracted from the given images. The physical component depends on features of the edge or region) in isolation. The spatial component involves the set of edges and regions adjacent to a given edge (or region) of the first image and the set of edges and regions adjacent to each potentially matching edge (or region) of the second image; thus the spatial context of each edge or region is considered. A computational network is used to represent this knowledge, it allows the computation of the likelihood of matching two edges or regions with logical and heuristic operators. An expert system shell called AGNESS (A Generalized Network-based Expert System Shell) is used to build a prototype system.

Pong, Ting-Chuen↗

NASA NTRS2005

A Review of Diagnostic Techniques for ISHM Applications

System diagnosis is an integral part of any Integrated System Health Management application. Diagnostic applications make use of system information from the design phase, such as safety and mission assurance analysis, failure modes and effects analysis, hazards analysis, functional models, fault propagation models, and testability analysis. In modern process control and equipment monitoring systems, topological and analytic , models of the nominal system, derived from design documents, are also employed for fault isolation and identification. Depending on the complexity of the monitored signals from the physical system, diagnostic applications may involve straightforward trending and feature extraction techniques to retrieve the parameters of importance from the sensor streams. They also may involve very complex analysis routines, such as signal processing, learning or classification methods to derive the parameters of importance to diagnosis. The process that is used to diagnose anomalous conditions from monitored system signals varies widely across the different approaches to system diagnosis. Rule-based expert systems, case-based reasoning systems, model-based reasoning systems, learning systems, and probabilistic reasoning systems are examples of the many diverse approaches ta diagnostic reasoning. Many engineering disciplines have specific approaches to modeling, monitoring and diagnosing anomalous conditions. Therefore, there is no "one-size-fits-all" approach to building diagnostic and health monitoring capabilities for a system. For instance, the conventional approaches to diagnosing failures in rotorcraft applications are very different from those used in communications systems. Further, online and offline automated diagnostic applications are integrated into an operations framework with flight crews, flight controllers and maintenance teams. While the emphasis of this paper is automation of health management functions, striking the correct balance between automated and human-performed tasks is a vital concern.

Patterson-Hine, Ann↗

NASA NTRSDate not supplied

Case Study: Analysis of Autonomous Center line Tracking Neural Networks

Deep neural networks have gained widespread usage in a number of applications. However, limitations such as lack of explainability and robustness inhibit building trust in their behavior, which is crucial in safety critical applications such as autonomous driving. Therefore, techniques which aid in understanding and providing guarantees for neural network behavior are the need of the hour. In this paper, we present a case study applying a recently proposed technique, Prophecy, to analyze the behavior of a neural network model, provided by our industry partner and used for autonomous guiding of airplanes on taxi runways. This regression model takes as input an image of the runway and produces two outputs, cross-track error and heading error, which represent the position of the plane relative to the center line. We use the Prophecy tool to extract neuron activation patterns for the correctness and safety properties of the model. We show the use of these patterns to identify features of the input that explain correct and incorrect behavior. We also use the patterns to provide guarantees of consistent behavior. We explore a novel idea of using sequences of images (instead of single images) to obtain good explanations and identify regions of consistent behavior.

Deep Neural Networks↗

NASA NTRSDate not supplied

Using Landsat 8 Satellite Imagery to Analyze Biogeochemical Constituents in the Waters of the San Francisco Bay Area and Beyond

The ocean's coastal zones play a key role in our planet's health and mitigate the adverse effects of climate change. Building on the success of NASA satellite imagery in mapping land cover changes around the globe in response to climate change, deforestation, and natural disasters, I have worked to determine how aquatic reflectance images from the Landsat 8 sensor could be correlated with biogeochemical constituents within the waters of the San Francisco Bay Area and California coastline. By analyzing Landsat 8 satellite imagery from the years 2013-2020 in collaboration with data from the United States Geological Survey (USGS), San Francisco Estuary Institute (SFEI), and universities involved with the Harmful Algal Bloom Monitoring and Alert Program (HABMAP), I investigated which areas of the San Francisco Bay and California coastline demonstrated significant correlations with values extracted from the satellite imagery. Using a Chlorophyll Index (CI) ratio calculated from two Landsat 8 satellite reflectance bands, it was found that there is a positive correlation between the CI and calculated oxygen, suspended particulate matter, and silicate from several USGS sampling points. In contrast, there is a significant negative correlation between the CI and salinity, nitrite, and phosphate at those same locations. Moreover, large suspected harmful algal blooms (HABs) along the California coastline seen in the Landsat 8 imagery were corroborated with HAB data from various institutions. Understanding the effectiveness of Landsat 8 aquatic reflectance images will allow scientists to predict HABs and other nutrient cycling that may be harmful to aquatic ecosystems around the world.

Landsat↗

NASA NTRS1980

Solar heating, cooling, and domestic hot water system installed at Kaw Valley State Bank and Trust Company, Topeka, Kansas

The building has approximately 5600 square feet of conditioned space. Solar energy was used for space heating, space cooling, and preheating domestic hot water (DHW). The solar energy system had an array of evacuated tube-type collectors with an area of 1068 square feet. A 50/50 solution of ethylene glycol and water was the transfer medium that delivered solar energy to a tube-in-shell heat exchanger that in turn delivered solar heated water to a 1100 gallon pressurized hot water storage tank. When solar energy was insufficient to satisfy the space heating and/or cooling demand, a natural gas-fired boiler provided auxiliary energy to the fan coil loops and/or the absorption chillers. Extracts from the site files, specification references, drawings, and installation, operation and maintenance instructions are presented.

Source record↗

NASA NTRS2022

A Global Evaluation of IMERG Precipitation Occurrence Using SMAP Detected Soil Moisture Change

A globally consistent ground validation method for remotely sensed precipitation products is crucial for building confidence in these products. This study develops a new methodology to validate the IMERG precipitation products through the use of SMAP soil moisture changes as a proxy for precipitation occurrence. Using a standard 2x2 contingency table method, preliminary results provide confidence in SMAP’s ability to be utilized as a validation tool for IMERG as results are comparable to previous validation studies. However, the method allows for an overestimate of false alarm frequency due to light precipitation events that can evaporate before the subsequent SMAP overpass and changes in overpass-to-overpass SMAP soil moisture that are within the range of SMAP uncertainty. To counter these issues, a 3x3 contingency table is used to reduce noise and extract more signal from the detection method. Through the use of this novel approach, the validation method produces a global mean POD of 0.64 and global mean FAR of 0.40, the first global-scale ground validation skill scores for the IMERG products. Advancing the method to validate precipitation quantity and the development of a real-time validation for the IMERG Early product are the crucial next developments.

Precipitation↗

NASA NTRS1988

A generic expert system for materials processing in space

A generic expert system is described for inspecting materials processed in space (MPS). The system may be applied, with the appropriate knowledge base, to any of the nondestructive testing methods (NDT) which are appropriate to MPS. Regardless of the method being used, the inspection process consists of three tasks: (1) signal or image processing of the NDT output and feature extraction, (2) interpretation of features in terms of MPS discontinuities, and (3) evaluation of the quality of the MPS based upon industry standards. In contrast to rule based systems, this system represents its knowledge as multidimensional vectors and appropriate functions on them. Currently, the expert system accepts manual input of observed features. Once the expert system has been tested and compared to human expert inspectors, a vision front-end will be developed to complete automation of the expert MPS inspection system, based on visual discontuities. Then the data base will be extended to include a variety of other NDT methods. In addition to functional performance, ease of use was established through menu window driven input as well as flexibility in building, using and modifying data bases for different applications.

Andersen, Kristinn↗

NASA NTRS2004

Electrokinetic In Situ Treatment of Metal-Contaminated Soil

An electrokinetic technique has been developed as a means of in situ remediation of soils, sludges, and sediments that are contaminated with heavy metals. Examples of common metal contaminants that can be removed by this technique include cadmium, chromium, zinc, lead, mercury, and radionuclides. Some organic contaminants can also be removed by this technique. In the electrokinetic technique, a low-intensity direct current is applied between electrodes that have been implanted in the ground on each side of a contaminated soil mass. The electric current causes electro-osmosis and migration of ions, thereby moving aqueous-phase subsurface contaminants from one electrode to the other. The half reaction at the anode yields H+, thereby generating an acid front that travels from the anode toward the cathode. As this acid front passes through a given location, the local increase in acidity increases the solubility of cations that were previously adsorbed on soil particles. Ions are transported towards one electrode or the other which one depending on their respective electric charges. Upon arrival at the electrodes, the ionic contaminants can be allowed to become deposited on the electrodes or can be extracted to a recovery system. Surfactants and other reagents can be introduced at the electrodes to enhance rates of removal of contaminants. Placements of electrodes and concentrations and rates of pumping of reagents can be adjusted to maximize efficiency. The basic concept of electrokinetic treatment of soil is not new. What is new here are some of the details of application and the utilization of this technique as an alternative to other techniques (e.g., flushing or bioremediation) that are not suitable for treating soils of low hydraulic conductivity. Another novel aspect is the use of this technique as a less expensive alternative to excavation: The cost advantage over excavation is especially large in settings in which contaminated soil lies near and/or under industrial buildings and therefore excavation would be made even more expensive by the need to prevent damage to numerous underground pipes and cables.

Quinn, Jacqueline↗

NASA NTRS2019

Comprehensive Assessment of Models and Events Using Library Tools (CAMEL) Framework: Time Series Comparisons

The Comprehensive Assessment of Models and Events using Library Tools (CAMEL) framework leverages existing Community Coordinated Modeling Center services: Run on Request post processing tools that generate model time series outputs and the new Community Coordinated Modeling Center Metadata Registry that describes simulation runs using Space Physics Archive Search and Extract metadata. The new CAMEL visualization tool compares the modeled time series with observational data and computes a suite of skill scores such as Prediction Efficiency, Root Mean Square Error, and Symmetric Signed Percentage Bias. Model data pairs used for skill calculations are obtained considering a user selected maximum difference between the time of observation and the nearest model output. The system renders available data for all locations and time periods selected using interactive visualizations that allow the user to zoom, pan, and pick data values along traces. Skill scores are reported for each selected event or aggregated over all events for all participating model runs. Separately, scores are reported for all locations (satellites or stations) and for each location individually. We are building on past experiences with model data comparisons of magnetosphere and ionosphere model outputs from GEM2008, GEMCEDAR Electrodynamics Thermosphere Ionosphere, and the SWPC Operational Space Weather Model challenges. The CAMEL visualization tool is demonstrated using three validation studies: (a) Wang Sheeley Arge heliosphere simulations compared against OMNI solar wind data, (b) ground magnetic perturbations from several magnetosphere and ionosphere electrodynamics models as observed by magnetometers, and (c) electron fluxes from several ring current simulations compared to Radiation Belt Storm Probes Helium Oxygen Proton Electron instrument measurements, integrated over different energy ranges.

Rastätter, Lutz↗

NASA NTRSDate not supplied

A Lunar Ground Truth of Microbes that are Integral to Sustaining Biological Life Support Systems

A lunar outpost such as Gateway or a Mars transit vehicle will use a semi-closed to closed loop biological life support system (BLSS) adapted for microgravity and high levels of radiation. A moon habitat will likely exist under partial gravity conditions and sustained levels of high radiation as a semi-closed loop system able to get resources from Earth via Gateway. Additionally, the moon will act as a closed-loop testbed for Mars habitat operations and will employ various elements of in situ resource utilization (ISRU). Perhaps the longest running BLSS collective study to date is that of the European MELiSSA (Micro Ecological Life Support System Alternative) project, a circular life support system, established to gain knowledge on regenerative systems aimed at the highest degree of autonomy to produce food, water and oxygen from mission wastes. This setup has evaluated the use of discrete microbial compartments and a higher plant compartment to carry out the necessary life support functions to support crew. Such compartments utilize thermophilic anaerobes to break down human and inedible plant wastes, photoheterotrophic bacteria that can further metabolize volatile fatty acids, nitrifying bacteria that can convert ammonium to plant and microalgae available nitrates, and photoautotrophic bacteria and higher plants which will convert carbon dioxide to oxygen, purify water, and provide food for human consumption. This being the most advanced BLSS model example to date -aside from the Yuegong-1, Chinese Lunar Palace- with the most defined compartment composition, and the assumption that other BLSSs will build upon such models, it becomes relevant to study the effects of the lunar environment upon the microbes that are integral to a BLSS. In ramping up to advanced stage BLSS systems, relatively simple experiments can be conducted on Artemis missions using continuous culturing and sampling of the model microbes, subsequently subjected to DNA sequencing for mutational analysis monitoring and chemical analysis to assess the sustained ability to carry out their hallmark biochemical processes efficiently. A suite of microbes should be assessed, prioritizing those with the duel capacity to be utilized in an BLSS and the ability to biochemically facilitate ISRU goals, such as the ability to transform the biogeochemistry of Moon or Martian regolith into materials that can support crop growth or extract elements of industrial significance such as aluminum or iron.

Biological Life Support Systems↗

NASA NTRS2011

NASA Lunabotics Mining Competition for Universities: Results and Lessons Learned

Space Mining for resources such as water ice, and regolith, which contain many elements in the form of metals, minerals, volatiles and other compounds, is a necessary step in Space Resource Utilization. One of the primary goals is to extract propellants from the regolith such as oxygen and hydrogen which could then be used for in-space transportation. In addition, the space mining system can be used for various construction tasks that can benefit human and robotic exploration as well as scientific investigations based on the exposed topography. The National Aeronautics & Space Administration (NASA) Lunabotics Mining Competition is a university-level competition designed to engage and retain students in science, technology, engineering and mathematics (STEM). NASA will directly benefit from the competition by encouraging the development of innovative lunar excavation concepts from universities which may result in clever ideas and solutions which could be applied to an actual lunar excavation device or payload. The challenge is for students to design and build a remote controlled or autonomous excavator, called a lunabot, that can collect and deposit a minimum of 10 kilograms of lunar simulant within 15 minutes. The complexities of the challenge include the abrasive characteristics of the lunar simulant, the weight and size limitations of the lunabot, and the ability to control the lunabot from a remote control center. This paper will present the results of the first and second annual Lunabotics Mining Competitions held in May 2010 and May 2011. In 2010, 22 United States (US) universities competed, and in May 2011 the competition was opened to international participation, with 46 Universities expected to attend. There are 12 international teams and 34 US teams. This combined total directly inspired an estimated 544 university students. More students and the public were engaged via internet broadcasting and social networking media. The various designs will be cataloged and categorized to provide information to future Lunabotics mining robot designers and competitors. It is also expected to be of value for actual future space missions, as knowledge is gained from testing many innovative prototypes in simulated lunar regolith.

Mueller, Robert P.↗

NASA NTRS2012

Lunabotics Mining Competition: Inspiration through Accomplishment

Space Mining for resources such as water ice, and regolith, which contain many elements in the form of metals, minerals, volatiles and other compounds, is a necessary step in Space Resource Utilization. One of the primary goals is to extract propellants from the regolith such as oxygen and hydrogen which could then be used for in-space transportation. In addition, the space mining system can be used for various construction tasks that can benefit human and robotic exploration as well as scientific investigations based on the exposed topography. The National Aeronautics & Space Administration (NASA) Lunabotics Mining Competition is a university-level competition designed to engage and retain students in science, technology, engineering and mathematics (STEM). NASA will directly benefit from the competition by encouraging the development of innovative lunar excavation concepts from universities which may result in clever ideas and solutions which could be applied to an actual lunar excavation device or payload. The challenge is for students to design and build a remote controlled or autonomous excavator, called a lunabot, that can collect and deposit a minimum of 10 kilograms of lunar simulant within 15 minutes. The complexities of the challenge include the abrasive characteristics of the lunar simulant, the weight and size limitations of the lunabot, and the ability to control the lunabot from a remote control center or operate autonomously. This paper will present an update of the results and lessons learned during the first and second annual Lunabotics Mining Competitions held in May 2010 and May 2011. It will also preview the 2012 competition with a review of the revised rules. In 2010,22 United States (US) universities competed, and in May 2011 the competition was opened to international participation. In 2011, 36 teams actually competed from 26 USA states and 4 foreign countries (India, Bangladesh, Colombia and Canada). This combined total directly inspired an estimated 653 university students. In 2012 more students and the public will be engaged via internet broadcasting and social networking media. The various designs will be cataloged and categorized to provide information to future Lunabotics mining robot designers and competitors. It is also expected to be of value for actual future space missions, as knowledge is gained from testing many innovative prototypes in simulated lunar regolith.

Mueller, Robert P.↗

NASA NTRSDate not supplied

Failure Modes and Mitigation Strategies for a Turboelectric Aircraft Concept with Turbine Electrified Energy Management

The electrification of gas turbine engines represents a major step-change in aircraft propulsion systems commonly known as Electrified Aircraft Propulsion (EAP). EAP involves the integration of electric machines potentially functioning as generators for large scale power extraction, as motors providing electrical augmentation of the engine spools, and even as a means of driving propulsors beyond the immediate scope of the engine. It may also include the use of energy storage. These and other characteristics of hybrid electric propulsion systems are relatively new to aircraft propulsion. The expanded propulsion architecture can be leveraged to improve propulsive efficiency and achieve better vehicle aerodynamics and controllability. It can also allow for additional benefits such as those enabled through Turbine Electrified Energy Management (TEEM). As the propulsion system and its functions expand, new failure modes are introduced. Due to the highly coupled nature of the propulsion system, failures could propagate throughout the system in ways that are unique to the new EAP architectures. To build confidence in the safety and practicality of EAP concepts, these failure modes need to be identified, explored, and addressed through mitigation strategies. This paper seeks to evaluate failure modes and failure mitigation strategies for the EAP concept known as the Single aisle Turboelectric AiRCaft with Aft Boundary Layer propulsor (STARC-ABL). The TEEM control concept is applied to improve transient operability. Several failure modes are considered and control based failure mitigation strategies are proposed with the goal of retaining operability and overall thrust. The results demonstrate the ability to maintain operability and a substantial amount of thrust in the event of various types of failures. Some challenges are also identified and discussed.

Turbine Electrified Energy Management↗

NASA NTRSDate not supplied

Beyond BioSentinel: Iterative Development of Automated Microfluidics

NASA Ames has flown a series of Bio-CubeSats that performed biology experiments supported by automated fluidic systems. Since Genesat-1 in 2006, these payloads have increased in complexity and functionality, building upon previous successes, and applying lessons learned. BioSentinel was the most recent of this series, launched into heliocentric orbit onboard Artemis-1 in 2022. This presentation will discuss how the fluidic technology developed for these Bio-CubeSat missions, including the multi-layer polycarbonate manifolds at the heart of the BioSentinel BioSensor, have spurred the development of several additional projects. Most directly is the modified BioSensor that will be a part of LEIA, which will perform its Lunar biology experiment onboard a Commercial Lunar Payload Services lander. Several search-for-life manifolds have been designed to prepare samples from icy moons for downstream analyses. Two early career Polaris projects are developing fluidics to perform genetic sequencing on samples from multigenerational cell culture and to extract and quantify target miRNAs to support astronaut radiation health assessment. Improving the readiness of these systems has been accelerated by adopting the established flight heritage and microgravity-compatibility of the Bio-CubeSat fluidic hardware and designs, while focusing development efforts on the integration of novel functionalities and components.

microfluidics↗

NASA NTRSDate not supplied

Vacuum Sealable Container (VSC) and Astronaut Lunar Drill (ALD) for Artemis

Introduction: NASA’s Artemis Program is under development to send first woman and next man to the Moon. Artemis will utilize a suite of new technology for Lunar exploration, including new space vehicles, new space suits, and new Astronaut Tools. Honeybee Robotics has been working with NASA JSC to develop a new Vacuum Sealable Container (VSC) and new Astronaut Lunar Drill (ALD) for the upcoming Artemis missions. Vacuum Sealable Container: Sample return continues to be the “Holy Grail” of space exploration, allowing for the analysis of materials using Earth-based laboratories instead of needing to miniaturize and ruggedize instrumentation for space. The Apollo missions to the Moon had several kinds of Sealable Containers which brought back Lunar samples for analysis [1]. These samples are still being analyzed, fifty years later. The VSC requirements are different from that for Apollo containers and as such, new development was required. One major difference between Artemis samples and those from Apollo is the desire to bring back volatiles which may be part of lunar regolith. The VSC is designed to withstand a high-pressure differential caused by sublimating volatiles. Because of the new, stricter sealing requirements, additional features have been added to the VSC. For example, the seal on the container is required to be more robust, thus required more force to actuate, and the seal must be locked in place with a secondary mechanism. Astronaut Lunar Drill: The ALD is designed to be a multi-functional platform for Lunar sample acquisition. The drill builds on lessons learned from the Apollo Lunar Surface Drill (ALSD), as well as Honeybee’s long history of mechanized sample acquisition devices for space [2]. The main functionality of the ALD is Deep Core Regolith Drilling. Additional functionality includes Surface Rock Coring (SRC), and GeoTech Tools (GTT). The ALD is a rotary-percussive drill designed with deep drilling in mind. The ALD is currently designed to have decoupled rotary and percussion subsystems to allow for maximum battery life and reduced fatigue on the crewmember. Honeybee drill technology will automatically engage the percussion when needed to drill at maximum efficiency. The mechanized drill stand helps improve drilling efficiency; the system utilizes advanced drilling algorithms which only require the crewmember to hold a single switch. Additionally, the stand aids in extraction of deep cores, something which was a problem on Apollo. The SRC functionality of the ALD utilizes Honeybee’s Eccentric Tube Core Breakoff technology to collect and retain rock core samples. This technology has also been infused into the Perseverance rover mission. The ALD is removable from the stand to allow crewmembers to collect samples from large boulders. Bringing back rock cores samples instead of full rocks allows for a wider variety of samples to be returned to Earth for study and puts them in a uniform form-factor for effective sealing and analysis. SRC bits will utilize the power of the drill’s percussion system to drill hard Lunar rocks and expedite sample acquisition. The mechanized stand on the ALD allows for additional attachments for taking geotechnical measurements with a Static Cone Penetrometer (SCP) and a Shear Vane (SV). With the stand, the ALD can take SCP measurements with the touch of a button, storing data for return to Earth. SV measurements utilize the ALD’s Rotary motor to spin the vanes in a controlled manner, getting clean data untampered by human error. References: [1] Bar Cohen and Zacny (2009), Drilling in Extreme Environments - Penetration and Sampling on Earth and Other Planets, Wiley. [2] Bar-Cohen and Zacny, Advances in Terrestrial and Extraterrestrial Drilling, CRC Press. [3] Myrick (2003), Core Break-off Mechanism. US Patent No. 6,550,549 Acknowledgements: This work has been supported by NASA via SBIR Phase 3.

Artemis↗