Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “air electrode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Scaling of energy delivered through an electrostatic discharge to a small series load

We study the energy delivered through a small-resistance series “victim” load during electrostatic discharge events in air. For gap lengths over 1 mm, the fraction of the stored energy delivered is mostly gap-length independent, with a slight decrease at larger gaps due to electrode geometry. The energy to the victim scales linearly with circuit capacitance and victim load resistance but is not strongly dependent on circuit inductance. This scaling leads to a simple approach to predicting the maximum energy that will be delivered to a series resistance for the case where the victim load resistance is lower than the spark resistance.

42 ENGINEERING↗
DOE OSTI2025

Ion-Pair Proton Exchange Membrane Fuel Cells for Heavy-duty Transportation

The purpose of this project is to build a fuel cell prototype that demonstrates high temperature proton exchange membrane fuel cell technology (HT PEMFC) commercial readiness. It advances from a technology baseline established in a prior CRADA in which these same Parties collaborated during the years 2020-2024. These efforts are aligned with the intentions of the DOE Hydrogen Fuel Cell Technology Office (HFTO) L’Innovator Pilot Program. Participant observes that its US-based competitive advantage may be improved by further optimizing Laboratory inventions. This CRADA is intended to further improve National Laboratory compositions and to develop commercial HT PEMFC membrane electrode assemblies (MEAs) that perform over a range of operating temperatures and relative humidity, that generate power from both low grade and pure hydrogen, and that are resistant to air impurities. Participant’s goal is to advance the commercial competitiveness of National Laboratory technologies in fuel cell products for heavy-duty truck integrators, for stationary power generation, marine applications, and for emerging interest from commercial aviation. The Parties will collaborate on producing a HT PEMFC MEA that integrates LANL ion pair technology and Brookhaven catalyst technology. The Laboratories plan to research and develop compositions for testing and evaluation. The participant will manufacture multiple MEAs based on the Laboratory compositions and will enable selected customers to validate performance characteristics. The Laboratories will convey to Participant the methods of making the National Laboratory compositions such that Participant may reproduce and then scale Laboratory methods into commercial production. Throughout the project, the Laboratories and Participant will iteratively test and optimize the compositions of materials of the MEAs, intending to optimize characteristics such as power density and lifecycle durability. Participant’s intended customers include fuel cells for large trucks, aviation, power back up, marine, and portable power.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2020

Fabrication of high-performance gas-diffusion-electrode based membrane-electrode assemblies

This paper demonstrates the fabrication and processing steps required to produce high performance fuel cell membrane electrode assemblies (MEAs) based on spray-coated gas-diffusion electrodes (GDEs). It is demonstrated that coating the catalyst layer with a thin layer of ionomer and then hot pressing the GDEs to the membrane is required to achieve comparable catalyst activity and air performance to catalyst-coated-membrane MEAs. We show that there is a critical amount of ionomer required to achieve maximized performance. Using electron microscopy, we show that the combination of the ionomer overlayer and hot-pressing bonds the catalyst layer to the membrane, increasing the interfacial contact area and quality of this interface. We also find that the ionomer overlayer smooths the surface of the GDE and provides increased contact area between the GDE and the membrane. Additionally, we demonstrate that much less ionomer is required for high-performance than has been previously reported. Through model fitting of electrochemical impedance spectroscopy, we show that this improvement in the catalyst layer - membrane interface reduces the effective catalyst layer resistance, which reduces Ohmic losses and increases catalyst utilization.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Advanced Computational Modeling of High-Level Waste Vitrification at the Hanford Site

The U.S. Department of Energy (DOE) has selected vitrification for stabilizing legacy tank waste at the Hanford site, where radioactive waste from plutonium production was historically stored in underground tanks. This waste will be separated into low-activity waste (LAW) and high-level waste (HLW) fractions and processed at the Waste Treatment and Immobilization Plant (WTP). At WTP, glass melters are used for the vitrification of radioactive tank waste, transforming it into a stable borosilicate glass form for safe long-term storage. The melter vessel is constructed from highly durable and heat-resistant materials, where the vitrification process occurs. The main regions that are modeled are the melt pool, plenum, cold cap, riser/discharge chamber, and surrounding structure with insulation layers. Forced convection induced by air bubblers at the base of the melter ensure uniform temperature distribution and provide heat to the cold cap layer. The cold cap is a region of reacting batch feed that floats on top of the molten glass and is where the batch-to-glass reactions occur. Joule heating provided by electrodes mounted along the vertical walls of the melter and immersed directly in the glass, generates the necessary heat for the net endothermic conversion processes that occur in the cold cap. The high temperatures, radioactivity, and opaque nature of the glass prevent direct observation inside the melters. Therefore, computational models are essential for providing insight into factors that affect melter throughput. Thermocouples in the plenum provide operators with plenum temperature measurements. Operational adjustments include bubbling rate, voltage supplied to the electrodes, feed adjustments, and glass removal rate. Different computational fluid dynamics (CFD) models have been developed, each serving a specific purpose. There are CFD models of different scale melters, as well as models that capture the two-phase flow interfaces of rising bubbles in the molten glass or models with a simplified molten glass region so that the surrounding structure and plenum can be feasibly incorporated. Pilot-scale melter models have been developed to serve as validation of the methods employed in the simulation of the full-scale WTP melters. Models incorporating resolved bubbling are used to develop momentum source terms to implement into a single phase, multi-region, steady-state flow model that is being validated by measured process parameters such as glass production rate, voltage, input power, plenum temperatures, etc. The resolved bubbling model uses the multiphase volume of fluid approach to model the system with a high-resolution interface capturing scheme to maintain sharp interfaces between the molten glass and the air phase. The suite of CFD models is continually being improved to incorporate more realistic physics and achieve faster turnaround time. For example, an incremental controller is implemented to automatically adjust electrode voltage within the simulation to a molten glass set point temperature of 1150°C. Newer models feature improved meshes to ensure conformal meshes between regions and eliminate unnecessary mesh refinement in areas that are not of interest (such as boundary layers in offgas ports). Instead of explicitly modeling the structural, refractory, and insulation layers of the melter, a thermal resistance approach is used with published correlations used for boundary conditions. The development of robust and efficient CFD models will be instrumental in enabling the WTP to successfully fulfill its mission of safely stabilizing legacy nuclear waste.

12 - MGMT OF RADIOACTIVE AND NON-RADIOACTIVE WASTE↗
DOE OSTI2021

Strong Fermi-level pinning at metal contacts to halide perovskites

The performance of halide perovskite-based electronic and optoelectronic devices is often related to interfacial charge transport. To shed light on the underlying physical and chemical properties of CH 3 NH 3 PbI 3 (MAPbI 3 ) in direct contact with common electrodes Al, Ti, Cr, Ag, and Au, the evolution of interfacial properties and Fermi level pinning is systematically studied. Given a unique experimental facility, pristine interfaces without any exposure to ambient air were prepared. We observe aggregation of substantial amounts of metallic lead (Pb 0 ) at the metal/MAPbI 3 interface, resulting from the interfacial reaction between the deposited metal and iodine ions from MAPbI 3 . It is found that the Schottky barrier height at the metal/MAPbI 3 interface is independent of the metal work function due to strong Fermi level pinning, possibly due to the metallic Pb 0 aggregates, which act as interfacial trap sites. The charge neutrality level of MAPbI 3 is consistent with the energy level of Pb 0 -related defects, indicating that Pb 0 interfacial trap states can be nonradiative recombination sites. Here this work underlines that control of chemical bonding at interfaces is a key factor for designing future halide perovskite-based devices.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Propagation of positive discharges in an air bubble having an embedded water droplet

Low temperature plasmas generated inside gas bubbles immersed in water is an effective method of rapidly transferring plasma generated reactive species to the water for applications in biomedicine, agriculture and environment. Reactive species are generally produced in the gas phase plasma and then solvate into the liquid. The large surface-to-volume ratio (SVR) of the bubble accelerates this process. In generating bubbles in water, aerosols and droplets are also contained within the bubble. These droplets also have a large SVR and so can be rapidly plasma activated. However, the presence of the droplets can also impact the propagation of the plasma in the bubble. In this paper, results are discussed from computational and experimental investigations of the formation and evolution of discharges in an air bubble immersed in water with an embedded water droplet. The computations were performed with a two-dimensional plasma hydrodynamics model. Experiments were performed with a quasi-2D bubble apparatus. In bubbles having a droplet, a plasma filament typically bridges from the powered electrode to the droplet, and then from the droplet to the bubble surface. A surface-hugging streamer also occurs on the inner bubble surface and on the surface of the droplet. Both surface streamers result in part from surface charge accumulation and can dominate the formation of reactive species that transport into the droplet. Increasing droplet conductivity suppresses propagation of the surface discharge and leads to a lower density of aqueous reactive species. Increasing conductivity of the surrounding water does not change the overall structure of the discharge but does slightly elevate the discharge intensity. Finally, the size and shape of the embedded droplet can significantly affect the formation and propagation of the streamer.

2D fluid modelling↗
DOE OSTI2025

Single Crystalline Na 0.67 Ni 0.33 Mn 0.67 O 2 Positive Electrode Material via Molten Salt Synthesis for Sodium Ion Batteries

P2-layered Na 0.67 Ni 0.33 Mn 0.67 O 2 (NNMO) has emerged as a promising positive electrode material for sodium ion batteries due to its appealing electrochemical properties. Synthesis of polycrystalline NNMO (PC-NNMO) materials through conventional calcination of solid precursors remains the prevailing method, where heating occurs in a dry environment with air or O 2 . On the other hand, the molten salt method, where precursors are submerged in molten salt medium during calcination, emerged in recent years to be a scalable technique for more controlled crystal growth and uniform morphology in a variety of materials. Here, we utilize the molten salt method to synthesize single crystalline NNMO (SC-NNMO) materials with enhanced electrochemical properties. The SC-NNMO material exhibits an initial specific discharge capacity of 95 mAh g –1 at a 0.1C rate, retaining approximately 88.5% of its capacity after 100 cycles over a wide voltage range of 2.0–4.2 V. Furthermore, SC-NNMO maintains a capacity retention of 83.9% after 300 cycles at a 1C rate compared to 66.6% for PC-NNMO, indicating excellent long-term cycling stability. This stability is further confirmed by the performance of an SC-NNMO//hard carbon full cell, which retains 90.3% of its capacity after 200 cycles at 1C within a voltage window of 1.9–4.1 V. The enhancement in stability of the SC-NNMO sample is attributed to the single crystalline structure suppressing the undesired P2–O2 phase transition at high voltage. This study also presents an easy, efficient, and straightforward molten salt process for SC-NNMO material synthesis, offering valuable insights into the potential application of such methodology for the large-scale, cost-effective production of various sodium-layered transition metal oxide positive electrode materials for SIBs.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Disinfection system with high throughput and low power requirements

Devices, methods and techniques are disclosed to perform high confidence sterilization of indoor air with low power requirements. In one example aspect, a sterilization device includes a power source, an energy storage coupled to the power source and configured to store electric charges, a set of electrodes arranged in a specified geometry to have a fixed characteristic impedance, and a switch positioned between the energy storage and the set of electrodes. The switch is configured to operate to establish a pulsed electric field on the set of electrodes.

Sampayan, Stephen↗
DOE OSTI2021

Electronic tuning of confined sub-nanometer cobalt oxide clusters boosting oxygen catalysis and rechargeable Zn–air batteries.

Reasonable design of robust bifunctional oxygen catalysts from an electronic structure perspective is intriguing and challenging for the development of high active rechargeable zinc-air batteries (ZABs). In this study, the favorable regulation of the electronic structure of the cobalt oxide nanoclusters was firstly predicted by density functional theory (DFT) simulation, and then experimentally verified by confining sub-nanometer CoOx clusters (0.86 nm) into the small pore of ZIF-8 derived N-doped nanomaterials (PNC) using a microporous MOFs confinement strategy. The confined effect of the MOF micropores not only enhanced the stability of the subnanometer cobalt oxide clusters, but also make it coupled with Co-Nx to further regulate the electronic structure of the former, synergistic resulting in enhanced ORR/OER actives. As a result, the optimized 0.05CoOx@PNC catalyst demonstrates outstanding bifunctional oxygen performance with a smaller potential gap of 0.67 V. Moreover, the rechargeable Zn-air batteries integrated 0.05CoOx@PNC air cathode displays encouraging performance with a peak power density of 157.1 mW cm(-2), a specific capacity of 887 mAh g(Zn)(-1)at 10 mA cm(-2) and long-term cyclability for over 200 h, significantly outperforming the benchmark electrode couple consisted of Pt/C/RuO2. DFT calculation further revealed that reducing particle size and coupling with Co-N could effectively regulate the charge distribution of CoOx nanoclusters and downshift the D-band center of Co adsorption sites in CoOx nanoclusters, which reduced the reaction barrier of intermediate O-2* and OH* and ORR/ OER over potential, thus accelerating the overall ORR/OER kinetic process. This work offers a novel reference for the construction of a robust sub-nanometer cluster catalysts in the field of ZABs.

Bifunctional oxygen electrocatalysts↗
DOE OSTI2024

A redox-reversible A/B-site co-doped BaFeO 3 electrode for direct hydrocarbon solid oxide fuel cells

Solid oxide fuel cells (SOFCs) can directly convert the chemical energy in fuel to electrical energy with fuel flexibility; however, the conventional nickel-based anodes face great challenges due to coking upon direct oxidation of hydrocarbon fuels and redox instability. Thus, developing new anode materials which can provide high coking resistance as well as redox stability is crucial. In this work, Ba 0.6 La 0.4 Fe 0.8 Mo 0.1 Ni 0.1 O 3-δ (BLFMN) has been synthesized in air using a sol–gel combustion method, resulting in a dual phase consisting of a cubic BLFMN main phase and scheelite BaMoO 4 (BMO 4 ) secondary phase. By heat-treating the BLFMN dual phase in H 2 at 800 °C for 5 h, a metallic nanoparticle-decorated BLFMN triple phase compound comprising cubic BLFMN, cubic BaMoO 3 (BMO 3 ) and in situ exsolved FeNi 3 alloy was obtained. BLFMN was subsequently investigated as an electrode material for La 0.8 Sr 0.2 Ga 0.83 Mg 0.17 O 3-δ (LSGM) electrolyte (300 μm) supported SOFCs. Symmetrical cells using BLFMN as electrodes with the cell configuration of BLFMN//LSGM//BLFMN showed excellent redox reversibility and a peak power density (PPD) of 1.32 W cm -2 at 850 °C when using H 2 as fuel. Single cell with the cell configuration of BLFMN//LSGM//LSCF (La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ ) reached PPD of 1.61 and 0.41 W cm -2 at 850 °C when operating with H 2 and CH 4 fuel, respectively. Moreover, the single cell exhibit excellent stability (over 300 h) upon direct oxidation of hydrocarbon fuels of CH 4 and C 3 H 8 . This study indicates that BLFMN is a promising redox reversible and coking resistant anode for SOFCs.

08 HYDROGEN↗
DOE OSTI2022

Plasma breakdown in bubbles passing between two pin electrodes

The ignition of plasmas in liquids has applications from medical instrumentation to manipulation of liquid chemistry. Formation of plasmas directly in a liquid often requires prohibitively large voltages to initiate breakdown. Producing plasma streamers in bubbles submerged in a liquid with higher permittivity can significantly lower the voltage needed to initiate a discharge by reducing the electric field required to produce breakdown. The proximity of the bubble to the electrodes and the shape of the bubbles play critical roles in the manner in which the plasma is produced in, and propagates through, the bubble. In this paper, we discuss results from a three-dimensional direct numerical simulation (DNS) used to investigate the shapes of bubbles formed by injection of air into water. Comparisons are made to results from a companion experiment. A two-dimensional plasma hydrodynamics model was then used to capture the plasma streamer propagation in the bubble using a static bubble geometry generated by the DNS The simulations showed two different modes for streamer formation depending on the bubble shape. In an elliptical bubble, a short electron avalanche triggered a surface ionization wave (SIWs) resulting in plasma propagating along the surface of the bubble. In a circular bubble, an electron avalanche first traveled through the middle of the bubble before two SIWs began to propagate from the point closest to the grounded electrode where a volumetric streamer intersected the surface. In an elliptical bubble approaching a powered electrode in a pin-to-pin configuration, we experimentally observed streamer behavior that qualitatively corresponds with computational results. Optical emission captured over the lifetime of the streamer curve along the path of deformed bubbles, suggesting propagation of the streamer along the liquid/gas boundary interface. Plasma generation supported by the local field enhancement of the deformed bubble surface boundaries is a mechanism that is likely responsible for initiating streamer formation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Effects of surface chemical potentials on cation segregation

Surface cation segregation on perovskite-type electrodes is one of the major issues limiting the durability of high-temperature solid-oxide electrochemical cells, and this process is strongly dependent on temperature, the external gas-environment, and impurities in air, such as CO 2 . Here cation segregation on La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF) is systematically evaluated under a set of chemical potentials to determine the origin of surface segregation and the dominant factors that govern the segregation process. Temperature is the main driving force for surface strontium segregation as the thermodynamic stability of each phase varies, and the SrO particles appear primarily in a specific operating window. In addition to the required thermal energy, the presence of gaseous oxygen-containing molecules as reactants help drive the precipitation of SrO. Oxygen partial pressure (pO 2 ) controls the defect chemistry of LSCF, leading to promotion or suppression of surface segregation. The presence of CO 2 promotes the nucleation process and suppresses the surface migration step, significantly altering the surface morphology. We also show that A-site deficiency can limit the SrO segregation in certain conditions but shows no effect in others. This study reveals the impact of gas–solid interactions on surface segregation and highlights the subtle relationship between multiple segregation driving forces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Electric field measurements of DC-driven positive streamer coronas using the E-FISH method

This paper reports on electric field measurements, using the electric field-induced second harmonic (E-FISH) method, sampling the spatial structure and temporal development of DC-driven positive streamer coronas in atmospheric-pressure air at relevant timescales to examine the self-pulsating behavior of the discharge. The discharge is triggered from a point-to-plate geometry and consists of transient coronas, which bridge the inter-electrode gap and pulsate at about 3 kHz, superimposed with a persisting glow corona. The measurements presented challenge the phenomenological explanation for the pulsations based on field recovery at the anode driven by the evacuation of positive ions by electric drift effects and hint at a propagating wave-like feature from the plate-cathode to the tip-anode.

42 ENGINEERING↗
DOE OSTI2020

Use of in Situ Synchrotron Techniques to Probe the Oxidized Surface of Molybdenum Nitride Oxygen Reduction Electrocatalysis

The development of active and stable earth-abundant catalysts for the oxygen reduction reaction (ORR) is needed for widespread, economic development of fuel cell technologies. Designing and optimizing these non-platinum group metals is challenging, however, because they are susceptible to composition and structure changes, including dissolution, oxidation, and corrosion, both in air and under reaction conditions. To identify the active surface, and thus understand the properties that affect activity, the catalyst surface must be characterized in situ. Herein, we utilize a grazing incidence electrochemical cell to investigate in situ composition and morphology changes of a molybdenum nitride (Mo-N) thin film catalyst using grazing incidence x-ray absorption spectroscopy (GI-XAS) and x-ray reflectivity (XRR). In rotating ring disk electrode measurements, we find that the activity, selectivity, stability, and capacitance of the Mo-N catalyst is dependent on the maximum potential to which it has been exposed. Specifically, the overpotential required to reach -2 mA cm-2geo decreases by over 90 mV when the maximum potential is increased from 0.3 to 0.8 V vs RHE (Figure 1). Because the Mo-N oxidizes rapidly in air, ex situ characterization methods including x-ray photoelectron spectroscopy and time-of-flight secondary ion mass spectrometry can provide only limited insight into these in situ catalyst changes. Using in situ GI-XAS measurements at applied potentials between 0.3 and 0.9 V vs RHE, however, we are able to determine that the surface of the film oxidizes and becomes more amorphous when exposed to increasingly higher potentials (Figure 1). Furthermore, the surface remains oxidized on the order of several hours when returned to "ORR relevant potentials" (< 0.6 V vs RHE), indicating that this surface-oxidized nitride is the active surface for ORR. Using in situ XRR measurements, we find that there is no change in surface roughness at potentials below 0.7 V vs RHE, but the film roughens significantly at 0.8 V vs RHE, correlating with ex situ measurements of Mo dissolution at this potential (Figure 1). We therefore conclude that the intrinsic activity of the Mo-N catalyst increases when exposed to potentials up to 0.7 V vs RHE, while above that potential activity enhancements are due to the exposure of more active sites through dissolution. The in situ electrochemical surface-sensitive x-ray characterization as used here is a promising methodology for understanding and leveraging surface dynamics to improve the performance of non-traditional catalysts.

Kreider, Melissa↗
DOE OSTI2020

Recovering cavity effects in corrugated organic light emitting diodes

Cavity effects play an important role in determining the out-coupling efficiency of an OLED. By fabricating OLEDs on corrugated substrates, the waveguide and SPP modes can be extracted by diffraction. However, corrugation does not always lead to an enhancement in out-coupling efficiency due to the reduction of the electrode reflectance and hence the cavity effects. Based on the results of our rigorous couple-wave analysis (RCWA) simulation, we found that the cavity effects can be partially recovered using a low index Teflon layer inserted between the ITO anode and the substrate due to the enhancement of the reflectance of the corrugated electrodes. To verify the simulation results, we fabricated corrugated OLEDs having a low-index Teflon interlayer with an EQE of 36%, which is 29% higher than an optimized planar OLED. By experimentally measuring the OLED air mode dispersion, we confirm the cavity emission of a corrugated OLED is enhanced by the low index layer.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Optical interferometry of high-energy nanosecond pin-to-pin discharges in atmospheric air

This paper describes the construction and application of an optical-frequency Michelson interferometer for measuring electron number density within high-energy, high-power nanosecond pin-to-pin discharges (>10 mJ pulse energy, >1 MW pulse power). A 21 mJ, 11 ns spark across a 3 mm pin-to-pin electrode gap was analyzed at 7 ns into the discharge to demonstrate the operation of the interferometer. A peak electron density of 2.3 × 10 17 cm −3 was observed at these conditions, and it was consistent with estimates of plasma channel resistance based on V–I measurements. This initial work paves the way for a larger parametric study of the spatial and temporal dynamics of electron number density in nanosecond pin-do-pin discharges under various conditions.

electron number density↗
DOE OSTI2021

Simultaneous Electrospinning and Electrospraying for the Preparation of a Precursor Membrane Containing Hydrothermally Generated Biochar Particles to Produce the Value-Added Product of Carbon Nanofibrous Felt

Biochar is a byproduct generated from the hydrothermal liquefaction of biomass, such as corn stover, in an anaerobic environment. This work aims to convert biochar into a value-added product of carbon nanofibrous felt. First, the biochar-containing precursor membrane was prepared from simultaneous electrospinning and electrospraying. After thermal stabilization in air and carbonization in argon, the obtained precursor membrane was converted into a mechanically flexible and robust carbon nanofibrous felt. Electrochemical results revealed that the biochar-derived carbon nanofibrous felt might be a good candidate as a supercapacitor electrode with a good rate capability and high kinetic performance.

25 ENERGY STORAGE↗
DOE OSTI2020

X-ray Nanocomputed Tomography in Zernike Phase Contrast for Studying 3D Morphology of Li–O 2 Battery Electrode

In this work, we investigated the lithium peroxide (Li 2 O 2 ) and pore size distribution in lithium-O 2 battery electrodes at different states of charge using transmission X-ray microscopy coupled with Zernike phase contrast to carry out nano-Computed Tomography. We report that such technique enables, at the nanoscale, to distinguish light elements such as carbon and Li 2 O 2 in Li-O 2 battery cathode electrodes. We verified by wave-propagation simulation that this approach efficiently improves the contrast of images in comparison with the pure absorption. The Li 2 O 2 distribution and thickness, interphases, and pore network are visualized and quantified, which give a valuable insight into our cathode architecture. From this 3D analysis, we highlight modifications of the air-cathode morphology and the Li 2 O 2 spatial organization as well as their potential implication in terms of carbon surface passivation and pore-clogging. After the full recharge process, this technique can also reveal the spatial distribution of the residual Li 2 O 2 and other byproducts.

25 ENERGY STORAGE↗